Summit Appliance SWC1535B Use and Care Manual
Contents
1. N Remove the bottom hinge 2 by unscrewing the four lock screws 1 Be careful to hold the door firmly after removing the screws Fig 1 Gently pull down to remove the door from the right top hinge and place it on a padded surface to avoid the risk of damage Then remove the right top hinge 7 Fig 2 amp 3 Unscrew and transfer pins 4 and 3 of the hinge plate to the opposite side Fig 1 Pop out the cover caps on the left side of cabinet and use them to cover the screw holes on the right hand side Screw the alternative left top hinge 8 included in the fittings on the left hand side of cabinet Fig 3 Relocate the door to the designated position Then screw the bottom hinge assembly on the left designated position and tighten it after the door is leveled Fig 1 Remove the handle from the left side of the door and install it on the right side See page 9 Model SWC1875B gt t i AnnNnNNNA oA Sy a 2 lt Remove the door shaft assembly 2 by unscrewing the two lock screws 1 Be careful to hold the lower glass door firmly after removing the screws Fig 1 Gently pull down to remove the lo2. Door Shelves 6 Handle Security Lock Ventilation Grille t J Logs ice Legs Cabinet MODEL SWC1875B Digital Control Panel waa TT Fae Upper Door Handle Upper Zone Security U Lock Lower Door Lower Zone Shelves 14 Ventilation Grille Adjustable Legs Cabinet INSTALLATION INSTRUCTIONS BEFORE USING YOUR APPLIANCE Remove the exterior and interior packing Before connecting the appliance to the power source let it stand upright for approximately 2 hours This will reduce the possibility of a malfunction in the cooling system from handling during transportation Clean the interior surface with lukewarm water using a soft cloth Install the handle on the door See page 9 INSTALLATION OF YOUR APPLIANCE The appliance is designed for built in recessed or free standing installation WARNING Do not store or install the appliance outdoors CAUTION This appliance is designed for storing and cooling
3. e Switch on circuit breaker or replace fuse e The temperature is not set correctly e Check the set temperature e The ambient temperature could require e Set a lower temperature a lower temperature setting e The door was opened too often e Do not open the door more often than Appliance is price ane e The door was not closed completely e Close door properly not cold enough e Door is not hermetically sealed e Check the door seal and clean or replace e The condenser is too dirty e Clean the condenser when necessary e The ventilation opening is blocked or too e Clear the obstructions and clean the dusty dust e The room temperature is higher than e Put the appliance in a cooler place average e A large amount of bottles has been e Leave the appliance to work for a Appliance added to the unit while until the set temperature has turns itself on been reached and off e The door is open too often e Do not open the door more often than frequently necessary The door is not closed completely The door gasket does not seal properly Close door properly Check the door seal and clean or replace The light does Appliance is not connected to a power supply Tripped circuit breaker or a blown fuse Connect the appliance Switch on circuit breaker or replace k NOL NOE e The light was switched off on the control fuse panel e Switch on the light Vibrations e The appliance is not properly level e Level the appl
4. This unit is designed for either built in or free standing installation If you plan to use the unit in a built in application use the following dimensions for the enclosure Model SWC1535B SWC1875B Width 15 38 cm 23 60 cm Depth 23 59 cm 231 59 cm Height 341 87 cm 697 177 5 cm ELECTRICAL CONNECTION A WARNING Improper use of the grounded plug can result in the risk of electrical shock If the power cord is damaged have it replaced by a qualified electrician or an authorized service center This appliance should be properly grounded for your safety The power cord of this appliance is equipped with a three prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock Do not under any circumstances cut or remove the third ground prong from the power cord supplied For personal safety this appliance must be properly grounded This appliance requires a standard 115 120 Volt AC 60Hz three prong grounded electrical outlet Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded When a standard 2 prong wall outlet is encountered it is your responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet To prevent accidental injury the cord should be secured behind the appliance and not left exposed or dangling The appliance should alway
5. 1 F Indicator Light The indicator light is located at the right lower corner of the display The indicator light will be on when the multi key function is selected To perform the multi key function press and hold the first key then press the additional key s for at least 5 seconds and then release all the keys F C Selector Select the temperature display setting in Fahrenheit or Celsius degree To change the temperature from Fahrenheit to Celsius or from Celsius to Fahrenheit press and hold the LIGHT key for 5 seconds Setting the Temperature Control e The unit has two separate temperature zones The temperature of both zones can be set between 41 F and 72 F 5 C and 22 C The LOWER temperature zone is ideal for storing white and red wine at a setting of 55 F to 72 F 13 C to 22 C The UPPER temperature zone is suitable for storing champagne and white wine at a setting of 41 F to 55 F 5 C to 13 C e When the unit is plugged in for the first time the unit will power up automatically to the preset defaults The preset temperature at the factory for the UPPER temperature zone is 50 F 10 C and for the LOWER temperature zone is 60 F 16 C e You can press the left side UP and DOWN keys to control the internal temperature of the UPPER temperature zone and press the right side UP and DOWN keys to control the internal temperature of the LOWER temperature zone When you press the two keys at the same time the display
6. DEFROSTING e The unit defrosts automatically in normal operating conditions e The evaporator behind the rear wall of the unit defrosts automatically The condensate collects in the drainage channel behind the rear wall of the unit and flows through the drainage hole into the drip tray by the compressor where it evaporates e However frost may accumulate on the evaporator if the unit is repeatedly opened in a high heat or high humidity location If this frost pattern does not clear within 24 hours your unit will require manual defrosting STORAGE Bottles can differ in size Accordingly the actual number of bottles you can store may vary The approximate maximum bottle capacity can be achieved when storing traditional Bordeaux 750 ml bottles in bulk storage You may load your wine bottles in single rows or by stacking while taking note of the following if you do not have enough bottles to fill your wine cellar it is better to distribute the load throughout the wine cellar so as to avoid all on top or all below type loads Do remove or relocate adjustable wooden shelves to accommodate larger type of bottles or increase the capacity of the cellar by stacking the bottles up when necessary See instructions for removing shelves above Keep small gaps between the walls and the bottles to allow air to circulate As in an underground cellar air circulation is important to prevent mold and for a more homogeneous temperature with
7. of the appliance The size of the fuse or circuit breaker should be 15 amperes It is important that the appliance be leveled in order to work properly You may need to make several adjustments to level it All installations must be in accordance with local plumbing code requirements Make certain that the pipes are not pinched kinked or damaged during installation Check for leaks after connection Never allow children to operate play with or crawl inside the appliance Although the unit has been tested at the factory due to long term transit and storage the first batch of cubes must be discarded Do not use solvent based cleaning agents or abrasives on the interior These cleaners may damage or discolor the interior Use this appliance only for its intended purpose as described in this Instruction Manual Keep fingers out of the pinch point areas Clearances between the doors and between the doors and cabinet are necessarily small Be careful closing doors when children are in the area A DANGER A Risk of child entrapment Child entrapment and suffocation are not problems of the past Junked or abandoned appliances are still dangerous even if they will just sit in the garage a few days Before discarding your old refrigerator e Take off the doors e Leave the shelves in place so that children may not easily climb inside SAVE THESE INSTRUCTIONS LOCATION OF PARTS MODEL SWC1535B Digital Control Panel
8. or explosion And do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance The fumes can create a fire hazard or explosion Do not connect or disconnect the electric plug when your hands are wet Unplug the appliance or disconnect power before cleaning or servicing Failure to do so can result in electrical shock or death Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual All other servicing should be referred to a qualified technician A WARNING FOLLOW WARNING CALLOUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL Use two or more people to move and install appliance Failure to do so can result in back or other injury To ensure proper ventilation for your appliance the front of the unit must be completely unobstructed Choose a well ventilated area with temperatures above 60 F 16 C and below 90 F 32 C This unit must be installed in an area protected from the elements such as wind rain water spray or drips The appliance should not be located next to ovens grills or other sources of high heat The appliance must be installed with all electrical water and drain connections in accordance with state and local codes A standard electrical supply 115 V AC only 60 Hz properly grounded in accordance with the National Electrical Code and local codes and ordinances is required Do not kink or pinch the power supply cord
9. safety messages in this manual and on your appliance Always read and obey all safety messages This is the Safety Alert Symbol The symbol alerts you to potential hazards that can kill or injure you and others All safety messages will follow the Safety Alert Symbol and either the words DANGER or WARNING A DANGER A Danger means that failure to heed this safety statement may result in severe personal injury or death A WA R N N t Warning means that failure to heed this safety statement may result in extensive product damage serious personal injury or death All safety messages will alert you about the potential hazard tell you how to reduce the chance of injury and let you know what can happen if the instructions are not followed IMPORTANT SAFEGUARDS Before the appliance is used it must be properly positioned and installed as described in this manual so read the manual carefully To reduce the risk of fire electrical shock or injury when using the appliance follow basic precautions including the following DANGER A Plug into a grounded 3 prong outlet do not remove grounding prong do not use an adapter and do not use an extension cord Replace all panels before operating It is recommended that a separate circuit serving only your appliance be provided Use receptacles that cannot be turned off by a switch or pull chain Never clean appliance parts with flammable fluids These fumes can create a fire hazard
10. will show the last temperature set previously e NOTE The temperature set for the LOWER temperature zone must always be just as high as or higher than that in the UPPER temperature zone For optimal performance the set temperature of the two zones should differ by at least 8 F e The temperature that you desire to set will increase 1 C or 1 F if you press the UP key once on the contrary the temperature will decrease 1 C or 1 F if you press the DOWN key once The display flashes while you make the setting e After the temperature has been set the display shows the current inner temperature of the particular temperature zone e To view the set temperature at any time press the UP or DOWN key the set temperature will temporarily flash in the display for 5 seconds Then the display shows the current inner temperature again NOTE e If the unit is unplugged or power is lost or turned off you must wait 3 to 5 minutes before restarting the unit If you attempt to restart before this time delay the unit will not start When you use the unit for the first time or restart the unit after it has been shut off for a long time there could be a few degrees variance between the temperature you select and the one indicated on the LED readout This is normal and is due to the length of the activation time There should not be a problem once the unit has been running for a few hours 11 INTERIOR LIGHT The interior light makes it easy to vi
11. 1 over the pins 3 of the door and tighten the handle lt by screwing in screws 2 with an Allen wrench J OPERATING YOUR APPLIANCE It is recommended you install the appliance in a place where the ambient temperature is between 72 and 78 F 23 26 C If the ambient temperature is above or below the recommended temperatures the performance of the unit may be affected For example placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate The range of 41 72 F 5 22 C may not be reached RECOMMENDED TEMPERATURE SETTINGS Conservation 49 57 F 10 14 C Red Wines 58 72 F 15 22 C Dry White Wines 48 57 F 9 14 C Ros Wines 49 51 F 10 11 C Sparkling Wines 41 47 F 5 8 C CONTROL PANEL for SWC1535B ON OFF Power To turn the appliance ON or OFF touch the 0 symbol and hold for 5 seconds NOTE Pressing the POWER key once can switch off the audible alarm when the alarm is on LIGHT Turn the interior light on and off with this switch UP a Used to increase warm the set temperature by 1 C 1 F DOWN y Used to decrease cool the set temperature by 1 C 1 F Indicator Light The indicator light is located at the right lower corner of the display The indicator light will be on when the multi key function is selected To perform the multi key function press and hold the first key then pres
12. N TIME e Short vacations Leave the appliance operating during vacations of less than three weeks e Long vacations If the appliance will not be used for several months remove all items and turn off the appliance Clean and dry the interior thoroughly To prevent odor and mold growth leave the door open slightly blocking it open if necessary MOVING YOUR APPLIANCE 1 Remove all items 2 Securely tape down all loose items shelves inside your appliance 3 Turn the adjustable legs up to the base to avoid damage 4 Tape the door shut 5 Be sure the appliance stays secure in the upright position during transportation Also protect the outside of the appliance with a blanket or similar item ENERGY SAVING TIPS e The appliance should be located in the coolest area of the room away from heat producing appliances and out of direct sunlight e Ensure that the unit is adequately ventilated Never cover air vents e Do not keep the door open any longer than necessary 14 TROUBLESHOOTING You can solve many common problems easily saving you the cost of a possible service call Try the suggestions below to see if you can solve the problem before calling the servicer Troubleshooting Guide PROBLEM POSSIBLE CAUSE REMEDY e Appliance is not connected to a power e Connect the appliance Appliance supply does not e The appliance is turned off e Switch on the appliance operate e Tripped circuit breaker or a blown fuse
13. Service calls to repair or replace appliance light bulbs or broken shelves Consumable parts Such as filters are excluded from warranty coverage Damage resulting from accident alteration misuse abuse fire flood acts of God improper installation installation not in accordance with electrical or plumbing codes or use of products not approved by warrantor Replacement parts or repair labor costs for units operated outside the United States Repairs to parts or systems resulting from unauthorized modifications made to the appliance Expenses for travel and transportation for product service in remote locations The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES CUSTOMER S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE O
14. THER RIGHTS WHICH VARY FROM STATE TO STATE FELIX STORCH INC cMMIT 770 Garrison Avenue Bronx NY 10474 aa Phone 718 893 3900 For parts and accessory ordering Fax 718 842 3093 troubleshooting and helpful hints visit www summitappliance com www summitappliance com support Printed in China 17
15. bient air flowed in when rearranging and removing food Power failure for some time The appliance is faulty e The audible alarm is automatically silenced and the temperature display stops flashing when the temperature is sufficiently cold again e lf the door has been left open for more than 60 seconds the alarm will sound Pressing the POWER key once will switch off the audible alarm DOOR LOCK Your unit is provided with a lock and key combination The keys are located inside the plastic bag that contains the nstruction Manual Insert the key into the lock and turn it counterclockwise to unlock the door To lock the door do the reverse operation making sure the metal pin is engaged completely Remove the key and place it in a secure place for safekeeping WINE SHELVES To prevent damaging the door gasket make sure to have the door all the way open when pulling the shelves out of the rail compartment e For easy access to the stored bottles you can pull the 12 shelf approximately halfway out of the rail compartment However this unit was designed with a plastic post on each side of the shelf track to prevent bottles from falling When removing the wooden shelf from the inner rails make sure to remove all bottles first Then move the shelf to the position where the notches in the wooden shelf are exactly aligned with the plastic posts and lift the wooden shelf In order to replace the shelf repeat this procedure in reverse
16. ew your wine labels and enhances the display of your collection The LIGHT switch allows you to toggle between 2 modes of operation for the internal lights functional default mode and showcase mode If you are in functional default mode the lights will turn on only when the door is open If you are in showcase mode the lights will be on whether or not the door is open SABBATH MODE Sabbath mode is available for the observance of certain religious holidays This mode turns off the displays interior light and audible alarms and prevents them from turning on again Normal cooling operations will still take place To initiate Sabbath mode press the POWER and LIGHT keys at the same time for at least 5 seconds The indicator light will flash four times and confirm the Sabbath mode is ON Sabbath mode can be exited by repeating the above process The Sabbath Mode will automatically turn off after 96 hours TEMPERATURE MEMORY FUNCTION In the event of a power interruption power surge breaker switch etc the unit will remember the previous temperature settings and when the power is recovered the cabinet temperature will return to the same setting as before the power went off TEMPERATURE ALARM DOOR ALARM e The audible alarm sounds if the storage temperature is not cold enough The temperature display flashes at the same time e The cause of the temperature being too high may be Warm fresh food was placed inside Too much warm am
17. iance with the adjustable feet The appliance The rattling noise may come from the flow of the refrigerant which is normal As each cycle ends you may hear gurgling sounds caused by the flow of refrigerant in your appliance plete If temperature fluctuations occur the contraction and expansion of the inner walls may m ch foise cause popping and cracking noises e The appliance is not properly level e Level the appliance with the adjustable feet e The appliance is not properly level e Level the appliance with the ig bie will adjustable feet properly e The door was reversed and not properly e Check the door hinge and reassemble installed correctly 15 e The gasket is dirty e The shelves are out of position e Clean the door gasket e Check the shelves and refit correctly Display E1 or E2 e The air temperature sensor has failed e Call for service The alarm sounds and the temperature display flashes Has the appliance door been open for longer than 60 seconds If not then the temperature has risen higher or fallen lower than the temperature that has been set This could be due to e The appliance door being opened too often e The ventilation opening being covered or too dusty e A lengthy interruption to the power supply e A large amount of bottles has been added to the unit If yes close the door e Do not open the door more
18. in the cellar To facilitate air circulation do not overload your wine cellar Avoid obstructing the internal fans located inside on the rear panel of the wine cellar To prevent bottles from falling do not try to slide the shelves outward beyond the fixed position Do not pull out more than one loaded shelf at a time as this may cause the wine cellar to tilt forward if not properly installed 13 CARE AND MAINTENANCE CLEANING YOUR WINE CELLAR e Turn off the power unplug the appliance and remove all items including shelves e Wash the inside surfaces with a solution of warm water and baking soda about 2 tablespoons of baking soda to a quart of water e Wash the shelves with a mild detergent solution e Wring excess water out of the sponge or cloth when cleaning the area where the controls are located or any electrical parts e Wash the outside cabinet with warm water and mild liquid detergent Rinse well and wipe dry with a clean soft cloth e Do not use steel wool or a steel brush on the stainless steel CAUTION Failure to unplug the appliance during cleaning could result in electrical shock or other personal injury POWER FAILURE Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you minimize the number of times the door is opened If the power is going to be off for a longer period of time you need to take the proper steps to protect the contents VACATIO
19. often than necessary e Clear the obstructions and remove the dust e Leave the appliance to work for a while until the set temperature has been reached The icon is lit up and flashing in the temperature display e The display temperature is out of range e Only temperatures within the range 0 99 F 9 37 C can be displayed If the temperature is not within this range the icon will be displayed instead This is normal 16 LIMITED WARRANTY ONE YEAR LIMITED WARRANTY Within the 48 contiguous United States for one year from the date of purchase when this appliance is operated and maintained according to instructions attached to or furnished with the product warrantor will pay for factory specified parts and repair labor to correct defects in materials or workmanship Service must be provided by a designated service company Outside the 48 states all parts are warranted for one year from manufacturing defects Plastic parts shelves and cabinets are warranted to be manufactured to commercially acceptable standards and are not covered from damage during handling or breakage 5 YEAR COMPRESSOR WARRANTY 1 The compressor is covered for 5 years 2 Replacement does not include labor ITEMS WARRANTOR WILL NOT PAY FOR Service calls to correct the installation of your appliance to instruct you how to use your appliance to replace or repair fuses or to correct wiring or plumbing
20. s be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance This provides the best performance and also prevents overloading house wiring circuits that could cause a fire hazard from overheating Never unplug the appliance by pulling on the power cord Always grip the plug firmly and pull straight out from the receptacle Repair or replace immediately all power cords that have become frayed or otherwise damaged Do not use a cord that shows cracks or abrasion damage along its length or at either end When moving the appliance be careful not to damage the power cord EXTENSION CORD Because of potential safety hazards under certain conditions it is strongly recommended that you do not use an extension cord with this appliance However if you must use an extension cord it is absolutely necessary that it be a UL CUL Listed 3 wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes REVERSING THE DOOR SWING OF YOUR APPLIANCE This unit has the capability of the door opening from either the left or right side The unit is delivered to you with the door opening from the left side Should you desire to reverse the opening direction please follow the reversal instructions shown below NOTE All parts removed must be saved to allow the door swing to be reversed Model SWC1535B
21. s the additional key s for at least 5 seconds and then release all the keys F C Selector Select the temperature display setting in Fahrenheit or Celsius degree To change the temperature from Fahrenheit to Celsius or from Celsius to Fahrenheit press and hold the LIGHT key for 5 seconds Setting the Temperature Control e You can set the temperature by touching the UP and DOWN symbols When you push the two buttons at the same time the LED readout will show the original temperature set previously The temperature preset at the factory is 54 F or 12 C e The temperature you are setting will increase by one degree each time you touch the UP symbol and will decrease by one degree each time you touch the DOWN symbol e The range of the temperature control is from 41 F to 72 F e To view the set temperature at any time touch the UP or DOWN symbol The set temperature will flash in the display window for 5 seconds After 5 seconds the temperature inside the unit will reappear in the display window CONTROL PANEL for SWC1875B o a amp Ms O A e A E ON OFF Power To turn the appliance ON or OFF touch the symbol and hold for 5 seconds NOTE Pressing the POWER key once can switch off the audible alarm when the alarm is on LIGHT Turn the interior light on and off with this switch 10 UP A Used to increase warm the set temperature by 1 C 1 F DOWN V Used to decrease cool the set temperature by 1 C
22. suMMIT WINE CELLAR INSTRUCTION MANUAL Model Nos SWC1535B SWC1875B BEFORE USE PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS Write Serial No on lower left corner of Felix Storch Inc 770 Garrison Avenue inside cabinet here Bronx NY 10474 www summitappliance com TABLE OF CONTENTS Important Safeguards Appliance Safety Location of Parts Installation Instructions Before Using Your Appliance Installation of Your Appliance Built in Cabinet Instructions Electrical Connection Extension Cord Reversing the Door Swing of Your Appliance Installing the Stainless Steel Handle Operating Your Appliance Recommended Temperature Settings Control Panel for SWC1535B Control Panel for SWC1875B Interior Light Sabbath Mode Temperature Memory Function Temperature Alarm Door Alarm Door Lock Wine Shelves Defrosting Storage Care and Maintenance Cleaning Your Wine Cellar Power Failure Vacation Time Moving Your Appliance Energy Saving Tips Troubleshooting Limited Warranty APPLIANCE SAFETY Your safety and the safety of others are very important We have provided many important
23. wer glass door from the middle hinge and place it on a padded surface to avoid the risk of damage Fig 2 Remove the middle hinge 6 by unscrewing the three bolts by the provided hex wrench Be careful to hold the glass door firmly after removing the screws Pull down to remove the upper glass door and place it on a padded surface to prevent scratching it Then remove the right top hinge 7 Fig 2 amp 3 Pop out the cover caps on the left side of cabinet and use them to cover the screw holes on the right hand side 5 Screw the alternative left top hinge 8 included in the fittings on the left hand side of cabinet Fig 3 6 Set the upper glass door to the designated position Then turn around the middle hinge 180 and refit it on the opposite side by screwing in the three bolts Level the door by adjusting the three fixing bolts And make sure that the spacers which the hinge pins sit on are correctly positioned Fig 3 7 Set the lower glass door to the designated position and install the two lock screws 1 to connect the door shaft assembly 2 with the glass door and tighten them before the door is leveled Fig 1 8 Remove the handles from the left side of the doors and install them on the right side See next section INSTALLING THE STAINLESS STEEL HANDLE This appliance includes a stainless steel handle that is not required to operate the unit To install the handle follow the instructions below a Locate the handle
24. wines Do not store perishable food medicine or other medical products Place your Wine Cellar on a floor that is strong enough to support it when it is fully loaded To level the unit adjust the front adjustable legs For freestanding installation 5 inches 127mm of space between the back and sides of the unit are suggested which allows the proper air circulation to cool the compressor and condenser for energy saving Even for built in installation you should provide the following clearances to ensure the best operation and proper ventilation 3 16 on both sides 2 at the rear and 1 16 at the top Take care that the air vent at the front of the appliance is never covered or blocked in any way NOTE It is recommended that you do not install the appliance near an oven radiator or other heating source Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption Don t install in a location where the temperature will fall below 60 F 16 C For best performance do not install the appliance behind a cabinet door or block the base grille Avoid locating the unit in moist areas Plug the Wine Cellar into an exclusive properly grounded wall outlet Do not under any circum stances cut or remove the third ground prong from the power cord Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized service center BUILT IN CABINET INSTRUCTIONS
Download Pdf Manuals
Related Search