iRobot 4409705 Use and Care Manual
Contents
1. untangled d Allow the unit to run in the pool for the entire cleaning cycle e Check that the Motor is operating f After following all of the above if there is still a problem visit global irobot com 7 Debris Comes Out Of The Unit When Removing It From Pool a Filter lock handle Top Access Lid Does Not Close Properly Check that the Lock handle release mechanism is not damaged The lid edges should be aligned with the unit s body and the top filter is properly locked b Intake Valves Check that the Filter Intake Valve Flaps see image above move freely to open and close Clean flaps if necessary global irobot com 13 Robo Power Supply Grounding The power supply must be connected to a grounded 3 conductor socket The main power supply must be connected via a GFCI ground fault circuit interrupter or RCD residual current device having a rated residual operating current not greater than 30mA e Ayla N Maintenance and safety Dimensions W D H 973mm 242mm 90mm The cover should not be removed except by an authorized service agent or trained and 10 75in 9 53in 3 54in qualified person No internal adjustment or component replacement can be carried out by Weight 1 9 Kg 4 19 lbs the user The power cable must be disconnected before removing the cover If the power TT supply cord is damaged it must be replaced by an authorized service agent or trained and Electrical qualified person Do not o2. IRODO L Mirra Pool Cleaning Robot Model 530 Manual irtobot IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL THE INSTRUCTIONS CAUTION Do not plug the power supply into a grounded outlet or do not switch the pool cleaner ON if it is not fully immersed in water Operating the cleaner out of waterwill cause severe damage immediately and will result in loss of warranty Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its cleaning cycle This will allow the motors to cool adequately Do not leave the cleaner in the pool all the time Always remember to turn the power supply OFF and unplug it from the power outlet before removing the cleaner from the pool WARNING The cleaner must not be used when people are in the water For use with swimming pool only Safety Note e The unit must be supplied through a residual current device RCD or GFCI having a rated residual operating current not exceeding 30 mA e The connection to the branch circuit should be consistent with the local and national wiring rules electrical code e Mishandling of the unit can result in leakage of lubricants e If the supply cord is damaged it must be replaced by the manufacturer s service agent or a qualified and trained person in order to avoid hazards This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack o
3. e 3 6m 11 8ft 12cm 4 7 inch 3 Place the unit in the water Turn the unit side to side in the water to allow air to escape from the body and then let the cleaner sink to the bottom of the pool Then spread the cable over thesurface of the pool asevenly as possible 10 iRobot Mirra 500 Series Owner s Manual 4 Plug the cable into the power supply Make sure the key on the plug corresponds exactly with the key slot on the socket of the power supply See details on the next page 5 Plug the power supply into a grounded outlet Ensure that the electric outlet has been properly grounded 6 Press the CLEAN button and the light will glow indicating that the system is ON and the pool cleaner will start the cleaning cycle 0 IMPORTANT Please be sure to always keep your pool cleaner properly stored anywhere between 10 to 40 degrees Celsius 50 to 104 degrees Fahrenheit This will keep the motors plastics and seals protected Robot can be used in water with temperatures ranging from 13 C to 35 C 55 F to 95 F However the recommended optimal temperature is between 22 C and 32 C 72 F and 90 F Robot Operating Your Pool Cleaner Plugging the Cable Plug To plug the cable Fig A into the socket on the power supply Fig B please do the following 1 Pre
4. f experience and knowledge unless they have been A given supervision or instruction concerning use of the appliance A by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance WARNING A Ground Fault Current Interrupter GFCI USA or a Residual Current Device RCD EUROPE must be installed to protect your electric outlet and preventany possible electric shock SAVE THESE INSTRUCTIONS Please read this manual completely before operating your pool cleaner 2 Robot Mirra 500 Series Owner s Manual Registration and Warranty Please visit www irobot com register to register your product and activate your warranty Components While the appearance of your cleaner and some of its components may differ from those shown here the function of the cleaner operating procedures and maintenance practices are the same 1 Handle 2 Cable 3 Outlet Top 4 Filter Access 5 Filter Lock Lever 6 Wheels 7 Unit Body 8 Intake Valves 9 Rolling Brush Your new automatic pool cleaner contains e The robotic pool cleaner with its floating cable e The Power Supply transformer iRobot Welcome Robot Dear Mirra Owner Thank you for choosing a new generation Robot Mirra pool cleaning robot You re joining a very special community of people 7 5 million worldwide and growing who are discovering just how useful convenient and straightforward having a
5. home robot is In fact owners tend to like their robots so much they ve even given them nicknames We re passionate about our robots too Not surprisingly given that making robots is all we ve ever done in the 20 odd years of our existence Now you re probably itching to give your Mirra a go but it s worth having a quick read of this manual first That way it will be even easier to use and save you even more time hope you will have many enjoyable experiences with your Mirra and on behalf of all the team thank you for choosing iRobot ES Colin Angle Chairman CEO and Co Founder Robot Corporation Best Wishes global irobot com 3 iRobot Table of Contents 2111 00 AA 5 Maintenance and Adjustment 6 Cleaning the Filter Changing the Rolling Brush 8 Accessing and Cleaning the Propeller 9 Operating Your Pool Cleaner pp 10 12 Troubleshooting pp 13 Power cansas 14 Declaration of Conformity pp 15 iRobot Customer Care pp 16 4 iRobot Mirra 500 Series Owners Manual Getting Started iRobot 3 6m 11 8ft mA SD i i 12 cm 4 7 inch Robo Maintenance and Adjustment INTAKE VALVES ADJUSTMENT Adjust filter valve to get best suction on gr
6. ilter canisters are thoroughly clean Clean as necessary After following all of the above if there is still a problem visit global irobot com 3 Unit does not move but does pump water a Check to see if forward reverse motion is obstructed by foreign matter hair debris etc on wheels or there is an entanglement with the power cord b Check there is no debris stuck inside the wheel between gears Verify if the rolling brush is properly positioned and not broken The brush is transferring the rotation to the wheels and if broken the robot will not move properly d After following all of the above if there is still a problem visit global irobot com 4 Unit does not climb the wall a Check to see if the filter canisters are thoroughly clean Clean as necessary 5 Unit does not pick up dirt and debris a Check 2a and 2b of this guide b Extend the water intake see page 6 Check the Filter Intake Valve Flaps on the underside of your unit see image below The Flaps should move freely to open and close Clean and free the Valve Flaps if necessary Filter Intake Valve Flaps 6 Unit does not seem to cover the entire pool a Most likely a thorough cleaning of the filter is needed b Verify that the unit rotates by 90 degrees on the first turn of a new cycle If not add or remove floats according to the instructions on page 7 c Check to see that the floating cable is properly spread out and is
7. light and avoid leaving it in the rain e Periodically straighten out the floating power cord e Occasionally you should rinse your cleaner in clean fresh water e Save your cleaner s packaging for off season storage or for shipping the unit to your This will lengthen the service life of your cleaner dealer if service is required e Clean the propeller once a month 12 iRobot Mirra 500 Series Owner s Manual Troubleshooting ireobot PLEASE CHECK THE FOLLOWING BEFORE CALLING YOUR SERVICE CENTER Before troubleshooting the pool cleaner must be disconnected from the power supply and the power supply must be unplugged from the electrical outlet to prevent damage to the unit and possible personal injury 1 Unit does not pump water or move a Check to see if electric outlet has power b Check if transformer is plugged into a grounded outlet and the cable assembly is plugged into the transformer Switch the power supply OFF and ON a few times Allow 45 seconds between ON and OFF d Check for and remove any debris such as hair string or leaves that may be obstructing the free movement of the wheels 2 Unit does not pump water at all or pumps slowly but moves a Check to see if propeller is seized due to accumulation of hair or debris on the propellers Remove the top screw on the outlet top and clean the propeller When reassembling the top cover do not overtighten the screw b Check to see if the f
8. ound Adjust filter valve to get best clearance on ground PVA WHEELS SOAKING Soak wheels after extended period of storage 6 iRobot Mirra 500 Series Owner s Manual iRobot Maintenance and Adjustment Continued FLOAT INSTALLATION Robot should turn 90 degrees on the first turn of a new cleaning cycle Remove filter canister to access float block holder Adjust amount of float blocks to achieve desired turning behaviors global irobot com 7 Robo Cleaning the Filter KN gt lt CLICK 8 iRobot Mirra 500 Series Owner s Manual ireobot Accessing and Cleaning the Propeller AN DISCONNECT THE ROBOT FROM THE POWER SUPPLY BEFORE PERFORMING THIS ACTION Clean the propeller if experiencing poor suction Robot global irobot com 9 irtobot Operating Your Pool Cleaner Set Up 1 Place the power supply transformer at least 3 6 meters 11 8 feet from the pool and atleast 12 cm 4 Inch above the surface The transformer will supply low voltage to the cleaner 2 Uncoil the cabl
9. pare the plug as seen in Fig C with the key and 3 outside slots exactly as shown 2 Fit exactly the key and the slots from cable plug with the corresponding key and slots from the power supply socket Fig D 3 Push the plug all the way into the socket of the power supply 4 Once the plug is in rotate the plug to the right to lock it into place Fig E 5 To remove the plug first rotate the plug to the left to unlock it then pull it out Fig F D slot Push and rotate right to lock Socket B Cable plug A global irobot com 11 irtobot Operating Your Pool Cleaner Power Button a Power LED The blue LED flashes when the power supply is in standby mode and lights continuously when the pool cleaner is operating b CLEAN button The button switches between ON and STANDBY IMPORTANT After every cycle the pool cleaner will automatically go to stand by In case you want to turn the machine off during the working cycle press the CLEAN button once and the LED will start flashing indicating that the machine has stopped running Maintenance Tips e Shut off and unplug the power supply every time you remove the cleaner from the water e Do not leave your cleaner in direct sunlight when not in use e It is recommended to clean the filter after every cycle e Never leave the power supply in direct sun
10. perate the supply if the cord is damaged Input rating 100 240V 50 60Hz 210W Output rating 29V 6 3A Environmental conditions Storage temperature 10 C 60 C 14 F 140 F The power supply is designed to work both indoors and outdoors However the unit should Operating temperature 0 C 45 C 32 F 113 F not be operated in direct sunlight or be exposed to water The power supply should not be gie proteron ey A operated in an ambient temperature in excess of 40 C 14 iRobot Mirra 500 Series Owners Manual Declaration of Conformity Test Standards EN60335 1 Household and similar electrical appliances Safety Part 1 General requirements EN60335 2 41 Household and similar electrical appliances Safety Part 2 Particular requirement for pumps EN62233 Electromagnetic fields Methods for evaluation and measurement FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception
11. ration 8 Crosby Drive Bedford MA 01730 USA All rights reserved iRobot is a registered trademark of iRobot Corporation Mirra is trademark of iRobot Corporation WC 4409773 Mirra Manual_EN BK0016000 REV PA
12. which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the manufacturer dealer or an experienced radio TV technician for help WARNING Changes modifications not expressly approved by Robot could void your warranty Robo global irobot com 15 ireobot Get Robot Updates Register your Robot Go to global irobot com iRobot Customer Care USA If you have questions or comments about this product please contact iRobot before contacting a retailer Please visit the iRobot home support site at www irobot com support for support tips frequently asked questions or information about accessories and other iRobot products Should you still need assistance Call our Customer Care team at 877 855 8593 iRobot Customer Care Hours e Monday Friday 7PM Eastern Time e Saturday 9AM 6PM Eastern Time Robot Customer Care Outside USA amp Canada Visit global irobot com to e Learn hints and tips to improve the performance of your robot e Get answers to questions e Download a detailed product manual e Contact your local distributor E 2008 2014 iRobot Corpo
Download Pdf Manuals
Related Search