SPT SD-9252SS Installation Guide
Contents
1. cma oo Figure 10 ADJUSTMENT If door does not open easily or falls too quickly you should adjust the tension of door spring Pull the spring adjustment pin out of the holes insert it in the next highest or lowest hole and test again Continue moving the spring pin until door is balanced Figure 11 Installation Instructions INSTALL POWER CORD Skip this step if dishwasher will be direct wired or has a factory installed power cord The power cord and connections must comply with the National Electrical Code Section 422 and or local codes and ordinances Be sure power is turned off at the source 1 Remove junction box cover 2 Secure house wiring to the back of the junction box with a strain relief 3 Connect incoming power cord white or ribbed to dishwasher white black or smooth to black and Ground to green wire Use UL listed wire nuts of appropriate size Replace junction box cover Check to be sure that wires are not pinched under the cover A A WARNING If house wiring is not 2 wire with ground a ground must be provided by the installer When house wiring is aluminum be sure to use UL Listed anti oxidant compound and aluminum to copper Connectors A C N Remove Insert Power Junction Box Cord Wires Thr Cover Strain Relief and Tighten Black Check That White Black and Green Dishwasher Wires Are Threaded D Thru Small Hole in Bracket Use UL Listed2. 5 Insert Drain Hose through Cabinet and Connect Water Line eee eer eer eee ee eee eee ee ee eee 5 IMPORTANT O N Slide Dishwasher into Cabinet sssssssicesissicsscsses 6 The dishwasher must be installed to allow for future removal from the enclosure if service is required Level Dishwasher sosro acne tkascsaeen tenses ctw teneti 6 Position Dishwasher Secure to Cabinet T Before You Begin Examine the dishwasher carefully 0 E if the productis damaged you should immediately contact ia a ae bi your dealer Connect Drain Ming sid sdtactsarenawssee seadae ad ae 8 Pre Test Check List siscs eeicisic sa cs eeinedscnsaaseceecs 9 FOR YOUR SAFETY Dishwasher Wet Test sss dsicecevesdengseeae ese s 9 Read carefully all WARNINGS and CAUTIONS in this instructions which will guarantee your safety Replace Toekick oo secee ccc e eee cece ence e eee eeees 9 Literature sed estes cas dae dander daadeseaswwteone es 9 Installation Preparation PARTS SUPPLIED Rae ces O Two 8 Philips flat head wood screws 5 8 long Z Z to secure dishwasher to underside of countertop or side of cabinetry taped to top or side of dishwasher 2 Wood Screws MATERIALS YOU WILL NEED O Ferrule compression nut and 90 Elbow 3 8 NPT PD external thread on one end opposite end sized to au Ay OS 0 fit water supply Wire Nuts 3 Hand shut off valve 90 Elbow O Thread Thread seal tape Ferruleand shut off Sea Tape UL listed wire nus 3
3. Compression Nut Valve Sy Waste tee for house plumbing if applicable Waste Tee Ey Hot Water fe Electrical cable or power cord if applicable Women Cable or Power Cord if applicable Materials For New Installations Only Air gap for drain hose if required Screw type hose clamps Strain relief for electrical connection Water line 3 8 min copper or 1 2 min plastic plastic must be tested for temperature and pressure Strain Relief Coupler for extending drain lin if applicable l Screw Type 01 Hose Clamps TOOLS YOU WILL NEED Phillips head screwdriver Ww 5 16 and 1 4 nutdriver pa yY Phillips head 5 16 and 6 Adjustable 6 adjustable wrench saat screwdriver 1 4 nutdriver wrench Carpenters square FN TAEA Carpenters Measuring tape g f square __ Safety glasses satety gasses Flashlight Flashlight AN Bucket to catch water when flushing the line 15 16 socket optional for skid removal Gloves Coupler QOOOOO0Oo0o000oo00 For New Installations Only O Tubing cutter O Drill and appropriate bits O Hole saw set Tubing cutter Drill and Bits Hole saw set CHOOSE and LV Installation Preparation UNIT DIMENSIONS 18 ee 2 3 LAJ DEPTH 23 580mm 33 35 WIDTH 18 450mm HEIGHTS33 35 840 890mm Figure 1 PREPARE THE LOCATION The dishwasher should be installed near a sink for water supply connection and proper drainage A build in dish
4. max From the opening 6 to 16 above the floor Installation Instructions PREPARE WATER LINE The line may enter from either side rear or floor within the shaded area The line may pass through the same hole as the electrical cable and drain hose Or cut an additional hole of 1 1 2 max Note Power cords with plug must pass through a separate hole 1 1 2 Dia 4 5 SRL Shut off Hole 1 naa i Figure 9 2 From Floor Cabinet Face WATER LINE CONNECTION Note to Consumer This dishwasher can use both hot or cold water Turn off the water supply Install a hand shut off valve in an accessible location such as under the sink Optional but strongly recommended Water connection is on the left side of the dishwasher Install the hot water inlet line using no less than 3 8 O D Copper tubing Route the line as shown and extend forward at least 19 from rear wall Flush water line to clean out debris The water pressure must be 20 120 PSI REMOVE TOEKICK Remove the two screws to remove toekick ADJUST DOOR BALANCE To check door balance hold the top of the dishwasher firmly Open the door slowly if the door drops when released increase spring tension If the door closes when released decrease tension Increase Spring Tension Decrease Spring Tension
5. 2 of length for a total of 10 ft to the factory installed hose Use 5 8 or 7 8 inside diameter hose and a coupler to connect the two hose ends Secure the connection with hose clamps Hose Clamp Coupler Hose Clamp Figure 22 Secure the drain hose to the air gap waste tee or disposer with clamps NOTE TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10 FEET FOR PROPER DRAIN OPERATION Connect drain line to air gap waste tee or disposer using either previously determined method Method 1 Air gap with waste tee of disposer a ee A yo Figure 23 air gap with waste tee Figure 24 air gap with disposer Method 2 Waste tee of disposer pa Figure 25 waste tee Figure 26 disposer Ly 4 Remove P IMPORTANT ja Hopper Plug If drain plug of disposer or waste tee has not been removed the dishwasher will not drain Disposer Waste tee Figure 27 Installation Instructions PRE TEST CHECK LIST Review this list after installation to avoid charges fora service call that is not covered by your warranty e Check to be sure power is OFF e Open door and remove all foam and paper packaging Locate the owner s manual in the literature package e Read the owner s manual for operating instruction e Check door opening and closing If door does not open close freely or tends to fall che
6. Srl 18inch Built In Dishwasher Installation Instruction SD 9252W SD 9252S5 Quality Innovation Style READ CAREFULLY AND KEEP THESE INSTRUCTIONS BEFORE INSTALLATION CONTENTS Read these instructions completely and carefully Material You Will Need is cscccc ceeds seescsececeass 1 IMPORTANT TOOIS earnederetineixasiaresedexmeemoene cian eee EEE eens 1 it Di IONS acs srsdarege g Ha 60s Masts bane veleeaeewees 2 Observe all governing codes and ordinances Gay Dusen Prepare the Location cccc cece eee e cece eee eeeeees 2 Note to Installer Corner Installation lt vs lt aiea snese seanids sanean imsaas 2 Be sure to leave these instructions for the consumers Ways of Drain Connections sessesssesesessseseo 2 and local inspectors use Prepare Electrical Wiring s ceeecceeeeeneeeees 3 Note to Consumer Electrical Requirement ccc cece cece cece ee eee 3 Keep these instructions with your Owners Manual for future reference Prepare Water Line cece cece cece cence eee eee eenee 4 Skill level Adjust Door Balance cece cece cece cece eeees 4 Installation of this dishwashers require basic mechanical f and electrical skills Improper installation can result in Remove Toekick ciisciccdisecssdcccidiviondoc ven cleeenes 4 prope t tatters Wiel is nay ebverdd undsr ale Eronet Install Power Cord ssdsisssscax sais ees caeee es siceaies 5 Warranty Position Water Line and House Wiring
7. Wire Nuts Figure 12 POSITION WATER LINE AND HOUSE WIRING Position water supply line and house wiring on the floor ofthe opening to avoid interference with base of dishwasher and components under dishwasher Water House Line Wiring Figure 13 INSERT DRAIN HOSE AND CONNECT WATER LINE Upright the dishwasher and position in the front of opening Insert drain hose into cabinet wall hole If a power cord is used guide the end througha separate hole hx X y NEI iy Figure 14 Connect the water line of dishwasher into user water line Installation Instructions SLIDE DISHWASHER INTO CABINET DO NOT PUSH AGAINST FRONT PANEL WITH KNEES DAMAGE WILL OCCUR Slide dishwasher into the opening a few inches at a time As you proceed pull the drain hose through the opening under the sink Stop pushing when the dishwasher is a few inches forward of adjacent cabinetry Make sure drain hose is not kinked under the dishwasher and there is no interference with the water line and wiring or any other component Figure 15 LEVEL DISHWASHER IMPORTANT Dishwasher must be level for proper dish rack operation and wash performance Place level on door and rack track inside the tub as shown to check that the dishwasher is level Level the dishwasher by adjusting the four leveling legs If adjustment to the right rear leveling leg is required lo
8. ck spring adjustment e Check to be sure that wiring is secure under the dishwasher not pinched or in contact with door springs or other components e Check door alignment with tub If door hits the tub level the dishwasher Pull lower rack out about half way Check to be sure it does not roll back or forward on the door If the rack moves adjust leveling legs e Check door alignment with cabinet If door hits cabinet reposition dishwasher e Check that door spring does not contact water line fill hose wiring or other components e Verify water supply and drain lines are not kinked or in contact with other components Contact with motor or dishwasher frame could cause noise Add 1 5 quarts of water to the bottom of the dishwasher to lubricate the pump seal e Turn on water supply Check for leaks Tighten connections if needed REPLACE TOEKICK Figure 28 Align toe kick along the bottom edge make sure it is against the floor Replace the two screws DISHWASHER WET TEST e Turn on power supply or plug power cord into outlet if equipped Start with normal wash e Check to be sure that water enters the dishwasher If water does not enter the dishwasher check to be sure that water and power supply are turned on e Check for leaks under the dishwasher If leak is found turn power supply off then tighten connections Turn on power again after leak is corrected e Check for leaks around the door A leak ar
9. hile the dishwasher is in operation The dishwasher requires the full capacity of the circuit If the wall socket used for the dishwasher is controlled by a switch turn off the switch before installation 1 The power supply socket for the appliance shall be installed in a cabinet or on a wall adjacent to the oe Alternate undercounter space in which the appliance is to be i Receptacle 1 installed i Location N 2 There shall be an opening through the partition coat aes i between the compartments specified in 1 that is o Locatie large enough for the attachment plug to pass through Ane ce ol The longest dimension of the opening shall not be more than 38mm 3 The edges ofthe opening specified in 2 shall if the partition is wood be smooth and rounded or if the partition is metal be covered with an edge protector provided for this purpose by the manufacturer and 3 1o fro Cabinet Px from Wall 4 Care shall be exercised when the appliance is Ground e installed or removed to reduce the likelihood of Figure 8 Waite damage to the power supply cord ELECTRICAL CONNECTION Electrical connection is on the right front of dishwasher For cable direct connections the cable must be routed as shown Cable must extend a minimum of 24 from the rear wall For power cord connections install a 3 prong grounding type receptacle in the sink cabinet rear wall 6 min and 16
10. osen junction box bracket screw and rotate bracket clockwise Check Level Front to Back Check Level Side To Side Turn Legs to Adjust Figure 17 Figure 16 Installation Instructions POSITION DISHWASHER SECURE TO CABINET The dishwasher must be secured to the countertop or the cabinet sides When countertops are made of wood use Method 1 When countertops are granite or other materials that will not accept screws use Method 2 to secure at the sides Method 1 Secure dishwasher to wood countertop Position dishwasher so that the door lines up with the front face of adjacent cabinets Fasten the dishwasher to the underside of the countertop with the 2 Phillips special head screws provided Brackets Wood Countertop T ols H sl c Je Brackets Figure 18 The dishwasher must be secured to the countertop by the two brackets on top of the dishwasher Method 2 Secure dishwasher with side mounting brackets Position dishwasher so that the door lines up with the front face of adjacent cabinets Remove plug buttons one on each side Install screws through the dishwasher side mount bracket and into the adjacent cabinet on each side Reinstall plug buttons Granite Counter
11. ound the door could be caused by door rubbing or hitting against adjacent cabinetry Reposition the dishwasher if necessary e Check drain lines when draining If leaks are found turn power off and correct as necessary After the unit drains open the door and make sure most of the water has drained If not check that disposer plug has been removed and or air gap is not plugged Let dishwasher turn through another fill and drain cycle Check again for leaks and correct as required LITERATURE Be sure to leave complete literature package and installation instructions with the consumer
12. s appliance must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is installed in an accordance with all local codes and ordinances A WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service representative if you are in doubt wether the appliance is properly grounded Do you modify the plug provided with the appliance If it will not fit the outlet have a proper outlet installed by a qualified electrician GROUNDING INSTRUCTIONS Cable Direct This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on appliance ELECTRICAL REQUIREMENT This dishwasher is designed for operation on an adequately wired individual 120VAC 60HZ and connected to an individual properly grounded branch circuit protected by a 15 or 20 amp circuit breaker or time delay fuse If the electric supply does not meet the above specifications contact a licensed electrician before proceeding Your dishwasher circuit should not be used for any other appliance w
13. top PE m aag 4 N Plug Buttons b Screws Figure 19 When step is complete either method close dishwasher door and verify that gap between countertop and top of dishwasher door is at least 1 2 Countertop a Min Dishwasher Door IMPORTANT Check to be sure the dishwasher is centered in the opening and there is no interference with adjacent cabinets when opening or closing the door Figure 20 Drive screws straight and flush Protruding screw heads will scratch the top or sides of the control panel and can interfere with door closing CONNECT WATER SUPPLY IMPORTANT Check to be sure that dishwasher does not rub or contact the fill hose or water supply line Test by opening and closing the door Re route the lines if a rubbing noise or interference occurs Wrap 90 elbow with tread seal tape Wrap 90 elbow onto the water valve Do not over tighten the 90 elbow water valve bracket could bend or water valve fitting could break Position the end of the elbow to face the left Connect water supply line to 90 elbow If water supply line could not be connected to 90 elbow directly slide ferrule against elbow and secure with compression nut 90 Elbow Thread Seal Tape Hot Water Supply Line Fill Hose Figure 21 Installation Instructions CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES If a longer drain hose is required add up to 4
14. washer must be fully enclosed on the top sides and back and must not support any part of the enclosure _ of the enclosure 33 35 1 2 Underside of Min 18 Floor must be Even With Room Floor Figure 2 DEPTH 24 610mm WIDTH 18 460mm HEIGHT 33 35 1 2 840 900mm CORNER INSTALLATION When installed into a corner allow 2 minimum clearance between dishwasher and adjacent cabinet wall or other appliances Allow 22 clearance from the front of the dishwasher for door opening Minimum Clearance 2 Fi gure 3 DRAIN CONNECTIONS The type of drain installation depends on the answers to the following questions e Is air gap required by local codes and ordinances e Will waste tee or disposer connection be less than 18 above the floor If both answers are YES use method A or B Otherwise choose C or D A air gap with waste tee a ee A yo Figure 4 B air gap with disposer Figure 5 C waste tee A Figure 6 D disposer Figure 7 Installation Preparation PREPARE ELECTRICAL WIRING A WARNING FOR PERSONAL SAFETY Remove house fuse or open circuit breaker before beginning installation Do not use an extension cord or adapter plug with this appliance GROUNDING INSTRUCTIONS Power Cord Models Thi
Download Pdf Manuals
Related Search