GE JX15BUMPWW Installation Guide
Contents
1. line drawn for cabinets with front overhang Line up the notch and center line on the mounting plate to the center line on the wall If the tabs are not in line with front overhang unit will be tilted While holding mounting plate with one hand draw circles on the wall at holes A B C and D see illustration above Four holes must be used for mounting NOTE Holes C and D are inside area E If neither C nor D is in a stud find a stud somewhere in area E and draw a fifth circle to line up with the stud It is important to use at least one wood screw mounted firmly in a stud to support the weight of the oven Set the mounting plate aside Drill holes on the circles If there is a stud drill a 346 hole for wood screws For holes that don t line up with a stud drilla hole for toggle bolts NOTE DO NOT MOUNT THE PLATE AT THIS TIME Installation Instructions 2 INSTALLING THE BUMP OUT BRACKET A ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using 2 4 toggle bolts At least one wood screw must be used to attach the plate to a wall stud NOTE Use hardware from OTR packaging 1 Remove the toggle wings from the bolts 2 Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to onto each bolt To use toggle bolts Spacing f2. Installation Bump Out Kit Instructions JX15BUMP For 15 Deep Cabinets 49 40719 07 14 GE Installation Instructions TOOLS YOU WILL NEED Ruler or tape a DEE O measure and 1 and 2 Phillips screwdriver A straight edge Carpenter square optional 2 A Tin snips for cutting damper if required Sgiesors to cut template if necessary Electric drill with 746 746 7 and drill bits Filler blocks or scrap wood pieces if needed for top cabinet spacing used on recessed YA f bottom cabinet be i k SN installations only Saw saber hole or keyhole Stud finder or Hammer optional Safety goggles Duct and masking tape MOUNTING SPACE needs to and free of obstructions be 30 or _ If the space between the cabinets is greater more from than 30 a Filler Panel Kit may be used to fill the eas in the gap between the oven and the cabinets i Your Owner s Manual contains the kit number for your model NOTES Il I Il Bottom edge NOTE Maximum cabinet depth is 15 of cabinet The space between the cabinets must be 30 wide i BaeKepieeh This oven is for installation over ranges up to 36 wide 66 or more If you are going to vent your oven to the outside from the see Hood Exhaust Section for exhaust duct floor to the preparation Teal the e When installing the oven beneath smooth flat cabinets be careful to follow the instr
3. or _ Toggles More Than gt lt Wall Thickness Toggle Wings Mounting Bolt End Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall Tighten all bolts Pull the plate away from the wall to help tighten the bolts
4. uctions on the top cabinet template for power cord clearance Installation Instructions PLACEMENT OF THE BUMP O UT BRACKET Find the studs using one of the following methods FINDING THE WALL STUDS A Stud finder a magnetic device which locates nails OR B Use a hammer to tap lightly across the mounting surface to find a solid sound This will indicate a stud location After locating the stud s find the center by probing evel line for front overhang Wall Studs the wall with a small nail to find the edges of the stud Then place a mark halfway between the edges The center of any adjacent studs should be 16 or 24 from this mark 3 Draw a line down the center of the studs THE OVEN MUST BE CONNECTED TO AT LEAST ONE WALL STUD ALIGNING THE WALL PLATE A i CAUTION Wear gloves to avoid cutting fingers NOTE Appearance and shape of the mounting plate on sharp edges may vary from your Hole Location A a model e Hole Location B Center of Top Cabinet Peak o 0 0 0 0 o aoge I C 1 mia Hole Location D Draw a vertical line on the wall at the center of the 30 wide space Use mounting plate as the template for the rear wall Place mounting plate on the wall making sure that the tabs are touching the bottom of the cabinet or the level
Download Pdf Manuals
Related Search