Home

Touch T714C Use and Care Manual

image

Contents

1. MM 16 PART 1 SET UP Helpful Hints Plug the brewer s electrical cord into its own grounded outlet If the same outlet is used with another electrical appliance then the electrical circuit may be overloaded causing the fuse or the circuit breaker to trip Filtered or bottled water is recommended for best tasting coffee tea or hot cocoa Use K Cup pack to brew 8 10 oz cup of coffee use our XBold cup packed with more coffee to brew 10 14 oz cup of coffee and use our XLarge cup to brew strong 12 14 oz cup of coffee T714C model offers five cup sizes 6 oz 8 oz 10 oz 12 oz 14 oz and three taste preference buttons to suit your taste MILD for mild strength coffee MED for medium strength coffee and BOLD for stronger strength coffee The default setting is BOLD which can be changed by pressing on the other MILD or MED button 5 Remove the Pod from the Red Cup Holder after each use A WN CAUTION POD IS HOT Unpacking Instructions Place the brewer box on a large steady surface such as a table or countertop or on the floor Open the box Remove the enclosed literature Turn the box on its side with front of the box face down Reach into the box and grasp the styrofoam that contains the brewer Carefully pull the styrofoam and packaging materials toward you and out of the box Remove the top styrofoam packaging material Carefully lift the brewer off of the bottom styrof
2. TOUGH serving people one cup at a time REAR VIEW PLUMBED READY T714C IMPORTANT SAFEGUARDS for Safe Operation amp Use When using electrical appliances basic safety precautions should be followed including the following a MS w N Read and follow all of the instructions in this manual before using the brewer to avoid injury The brewer pumps extremely hot water DO NOT touch hot surfaces Install the brewer in proper location as instructed in this manual Do not use accessory parts not recommended by Touch Coffee amp Beverages LLC Using unauthorized accessory parts may result in fire electrical shock or injury to persons Do not place on or near a hot gas or electric burner or in a heated oven The brewer is designed for indoor use only Do not use the brewer outdoors or near damp areas Do not immerse the electrical cord or the brewer in water or any other liquid as this may result in fire electric shock and injury to person Do not overfill the Water Tank with water Only use water to fill the Water Tank Do not put any other liquids or foods in the Water Tank unless instructed otherwise to clean the brewer in this manual Unplug the brewer from the outlet when not in use and before cleaning it Allow the brewer to cool before putting on or taking off parts Plug the electrical cord into its own dedicated electrical outlet with ground to reduce the risk of an electrical shock
3. Double check the top needle to see if it is clogged If so unclog the top needle using a paper clip or a tooth brush Double check the Red Cup Holder to see if the two bottom needles are clogged If they are clogged then use a paper clip or a tooth brush to clean the two bottom needles Brewer shuts off automatically The brewer is designed to automatically turn OFF after 30 minutes of non use to conserve power Double check the top needle underneath the cover to see if it is clear of coffee grind If the top needle is clogged use a paper clip or tooth brush to unclog the top needle On a rare occasion the brewer may shut OFF while brewing This may happen if the water in the water tank is too hot This is done to protect the heating mechanism in the brewer If this happens let the brewer cool down and replace the water in the water tank with room temperature water If the brewer continues to shut OFF while brewing after replacing the water please contact the customer service 14 PART 4 TROUBLESHOOTING The Brewed Water is not Hot Enough The water temperature can depend on the water temperature inside the Water Tank If you recently filled the Water Tank with cold water then brewed water may not seem hot as usual Pour some warm water into the Water Tank so that water temperature is about 24 C or 75 F If the room temperature is cold such as during the winter then the water temperature in the Water Tank may be too co
4. FROM ANY BREACH OF THIS WARRANTY EVEN IF FORESEEABLE Some states or provinces do not allow the exclusion or limitations of incidental or consequential damages so the above limitation or exclusion may not apply to you depending on the state or province of purchase Nor does this warranty cover damages caused by use accessories services performed by anyone other than Touch or its authorized service providers use of parts other than genuine Touch parts or external causes such as abuse misuse inappropriate power supply or acts of God Other Limitations THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS WARRANTY WHETHER WRITTEN OR ORAL IN ADDITION TOUCH HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO THE TOUCH S BREWER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE Some states or provinces do not allow disclaimers of such implied warranties or limitations on how long an implied warranty lasts so the above limitation may not apply to you depending on the state or the province of purchase 16 PART 5 WARRANTY Limited One Year Warranty How do you obtain warranty service Touch brewers are high quality appliances and with proper care are intended to provide years of satisfying performance However should the need arise for warranty servicing simply call Touch s Customer Service number provided on back of this manual Please do not return your brewer for s
5. and to prevent the fuse and circuit breaker from tripping The electrical cord comes with a grounding wire with a grounding plug to reduce the risk of electrical shock The electrical cord must be plugged into a 3 prong properly grounded outlet If your outlet is a 2 prong wall outlet then it is your personal responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet 14 Consult a qualified electrician to replace a 2 prong wall outlet with a 3 prong grounded wall outlet If the grounding instructions in this manual are not lear then consult a qualified electrician Do NOT cut or remove the third ground prong from the power cord Do not run the electrical cord through high traffic area or near hot surfaces Adult supervision is necessary when the brewer is used by or near children Do not open the brewer cover when the brewer is brewing a beverage Keep the lid closed on the Water Tank unless the Water Tank is being refilled with water Do not use the brewer for other than its intended use Do not modify or alter the brewer in any way Do not place smashed or damaged Pods in the brewer Do not use modified pods in brewer ex Pods that have been reused with tapes and adhesives Do not operate the brewer unattended Do not let the electrical cord hang over an edge of table or counter or touch hot surfaces Extreme caution must be used when moving the brewer containin
6. to hot water for five 5 minutes Fig 17 and rinse with warm water 3 Insert the Red Cup Holder back into the brewer Cleaning the two bottom Needles 1 There are two bottom Needles inside the Red Cup Holder Pull down the bottom funnel from the top Holder Fig 18 2 Check to make sure the two Needles are not clogged 3 If the two bottom Needles are clogged then use a paper clip or tooth brush to clean the Needles and rinse with warm water Fig 19 CAUTION There is a sharp Needle underneath the Cover and two sharp Needles inside the Red Cup Holder To avoid risk of injury and do not put your fingers in the Red Cup Holder Fig 19 i 5 min Fig 17 Fig 18 Fig 19 13 PART 4 TROUBLESHOOTING Brewer does not have power Plug the brewer into an independent outlet Check to be sure that it is plugged in securely Plug into a different outlet Reset your home s circuit breaker if necessary Make sure that the Power Button has been turned ON and the Power Light is illuminating Brewer will not brew If the upper left blue Low Water Light is blinking then add water to the Water Tank Make sure the Water Tank is seated and secured in properly on its base Double check the top needle underneath the cover to see if it is clear of coffee grind If the top needle is clogged use a paper clip or tooth brush to unclog the top needle Check to make sure Pod is not damaged Brewing a partial cup
7. N during warm up and the light will BLINK during the brewing cycle Fig 10 CAUTION The brewer will heat the water EXTREMLY HOT during the brewing process To avoid risk of injury do not pull on the Latch or open the Cover while brewing Contents will be EXTREMELY HOT Fig 10 6 If the brewer has been OFF for some time before turning ON the brewer there may be a short pause up to 30 seconds before the brewing process starts At the end of the brewing process the brewer will pump water to the Water Tank and a burst of air to purge the Pod of remaining liquid 7 Enjoy your cup of coffee tea or hot cocoa Fig 11 8 Pull the Latch and dispose of the used Pod Fig 12 CAUTION Pod will be HOT Fig 12 10 PART 2 BREWING A CUP Stopping the Brew Process If you need to stop the brewing process for any reason then press on the Power Button to turn OFF the brewer NOTE If the brewer is turned ON after terminating the previous brewing process the next brewing cycle may NOT brew a full cup We recommend performing a brewing cycle without the POD and then restart the brewing cycle with a POD in the Red Cup Holder Brewing Iced Beverages Place a tall cup filled with ice on the Drip Tray the Drip Tray Assembly can be removed to accommodate taller cups choose your favorite Pod and press the desired cup size button Purging the Brewer If your brewer has not been used for more than one week we recommend emptying the wat
8. and repeat cleansing by repeating the brewing cycle at least two 2 more times Fig 6 8 The one time set up process is now complete and the brewer is now ready AS Fig 4 PART 2 BREWING A CUP Ready to Brew Your First Cup 1 Make sure the brewer is powered ON Place a cup or mug on the Drip Tray 2 Pull on the Latch to open the Cover Fig 7 Insert a desired Pod into the Red Cup Holder Fig 8 NOTE DO NOT remove the foil lid or puncture the Pod Fig 8 When using a smaller cup the Drip Tray may be inserted into the Upper Slot to minimize splattering of coffee Fig 7 CAUTION There are three sharp Needles that puncture the Pod a top Needle underneath the Cover and two bottom Needles in the Red Cup Holder To avoid risk of injury do not put your fingers in the Red Cup Holder Fig 8 3 Close the Cover by pressing down on the Cover Handle Fig 9 4 Press on the desired cup button The default taste is BOLD You may select a different taste preference by pressing on the MILD or MED Button Fig 9 NOTE If you do not push a cup size button to start brewing within 60 seconds the brewer will be disabled to prevent accidental activation Re activate the Brewer by pulling on the Latch and Closing the Cover again 2 e i amp 2 MILD med BOLD PART 2 BREWING A CUP Ready to Brew Your First Cup Continued 5 The upper right brewing indicating light will stay O
9. er in the Water Tank and brew one cup without the POD Then start a brewing cycle with a Pod CAUTION Extremely Hot Water 11 PART 3 MAINTENANCE Cleaning External Parts We recommend regularly cleaning the brewer s external components CAUTION Only use a moist cloth and if necessary a mild detergent never use abrasive or aggressive detergents Do not wash machine parts in the dishwasher Fig 13 1 Use damp non abrasive cloth for cleaning the exterior of the brewer Never immerse the brewer in water or use a dishwasher to clean the brewer Fig 13 2 The Drip Tray can accumulate up to 6 oz of overflow To drain the Drip Tray remove the Drip Tray by pulling on it and discard the liquid Fig 14 Use damp non abrasive cloth to clean the Drip Tray Fig 14 DO NOT use a dishwasher to clean the Drip Tray Cleaning the top Needle 1 Double check the top Needle underneath the Cover Fig 15 to see if it is clear of coffee grind 2 If the top Needle is clogged then use a paper clip or tooth brush to clean the Needle Fig 15 DO NOT insert the paper clip to deep inside the needle Fig 15 PART 3 MAINTENANCE Cleaning the top Needle Continued CAUTION Top Needle is very sharp To avoid risk of injury do not directly touch this Needle with your finger Fig 15 Cleaning the Red Cup Holder 1 Open the Cover and remove the Red Cup Holder from the brewer by pulling on it Fig 16 2 Immerse the Red Cup Holder in
10. ervicing without first speaking to Touch Customer Service to obtain a Return Merchandise Authorization RMA number Touch brewers returned without an RMA number will be returned to the sender without servicing Touch is committed to your satisfaction If you have questions just give us a call to have them answered quickly without leaving the comfort of your home Touch Coffee amp Beverages LLC 15312 E Valley Blvd City of Industry CA 91746 U S A www touchbeverages com 17 PART 5 WARRANTY Warranty Registration Serial Number Po The serial number can be found on the bottom of the brewer and on the side of color box Date of Purchase p Where did you purchase your brewer Po Mr M Sr Po First Name FOO Last Name Po 18 Address Po State Po State Zip Code LL L Phone Number E mail Address Po would like to receive product news and information and special offer as described in your Privacy Policy at www touchbeverages com privacy policy Mail the Warranty and Registration Card to Touch Coffee amp Beverages LLC 15312 E Valley Blvd City of Industry CA 91746 U S A MEMO e UL us LISTED For Commercial Use Only To learn more about Touch visit www touchbeverages com or Call Toll Free 844 20TOUCH 844 208 6824 2014 Touch Incorporated All rights reserved
11. g hot liquids To unplug the brewer turn OFF the brewer first then unplug the electrical cord from the outlet SAVE THESE INSTRUCTIONS Warning to user and parents 1 Brewer injects EXTREMELY HOT WATER DO NOT let children use the brewer without adult supervision 2 After brewing cocoa or soluble IMMEDIATELY RUN an 8 oz brew cycle without the Pod in the brewer to rinse the brewer This will avoid clogging up the two Needles in the Red Cup Holder 3 Disconnect electrical cord immediately if brewer begins to malfunction 4 Do not place fingers directly under the spout while brewer is operating This may result in burning your fingers and scalding A WARNING CAUTION There is one 1 sharp Needle underneath the Cover and two 2 sharp Needles inside the Red Cup Holder Do not put your fingers in the Red Cup Holder CAUTION EXTREMELY HOT WATER is injected into the Red Cup Holder during the brewing process DO NOT lift the Cover during the brewing process CAUTION Keep the brewer in its upright position and place the brewer on a dry surface CAUTION 120V 60Hz 12 5A 1500W EXTENSION CORD INSTRUCTIONS In the event that a longer extension cord is necessary make sure 1 the marked electrical rating of the extension cord exceeds or meets the electrical rating of the brewer 2 arrange the cord so that it does not drape over the countertop and it cannot be pulled on by children or tripped over unintentionally and 3 the exte
12. ical cord and remove all pieces of adhesive tapes Then view the rear of the product Fig 1 2 Insert a 1 4 diameter water supply line into the Water Inlet Adaptor on the rear of the water tank Fig 2 NOTE If the water supply line is not 1 4 diameter an adapter may be needed Please consult a professional plumber if necessary 3 Place a large mug or cup 12 oz minimum on the Drip Tray Plug the brewer into a 3 prong grounded outlet Fig 3 4 Press the Power Button on top of the brewer The blue Power Light will illuminate Fig 3 5 About half of the water tank will fill automatically NOTE DO NOT insert a Pod into the Red Cup Holder at this time PART 2 BREWING A CUP Setting Up Your Brewer Continued CAUTION DO NOT pull the Latch to open the Cover during the brewing period Fig 4 CAUTION Extremely Hot Water Fig 5 6 With the cover closed press the 10 oz Button to start the brewing cycle Fig 5 The brewing indicating light on the upper right corner will stay ON while the brewer is warming up Note that the brewer will pump the water to the Water Tank while warming up This is normal and it may take up to 30 seconds to warm up from a cold start The brewing indicating light will start to blink when the brewing cycle starts CAUTION DO NOT remove the mug until the brewing indicating light stops blinking 7 Once the brewing is done remove the mug and pour the hot water into the sink Discard the hot water
13. ld Pour some warm water into the Water Tank so that water temperature is about 24 C or 75 F If the MILD taste preference is blinking then pres on BOLD button for hotter brew temperature If any problems persist contact Customer Service at the number noted on the back of this manual 15 PART 5 WARRANTY Limited One Year Warranty Touch Coffee amp Beverages LLC warrants that your brewer will be free of defects in materials or workmanship under normal commercial use for one year from the date of purchase It is recommended that you fill out and return the warranty card enclosed with the brewer so that the purchase information will be stored in our system Touch will at its option repair or replace a defective brewer without charge upon its receipt of proof of the date of purchase If a replacement brewer is necessary to service this warranty the replacement brewer may be new or reconditioned If a replacement brewer is sent a new limited one year warranty will be applied to the replacement brewer This warranty only applies to brewers operated in the United States and Canada This warranty gives you specific legal rights and you may also have other rights that vary from state to state and in the case of Canada from province to province What is not covered by the Limited Warranty THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND EXPENSES RESULTING
14. nsion cord has a 3 prong grounding plug THIS PRODUCT IS FOR COMMERCIAL USE ONLY UL US JS WARNING m THIS PRODUCT CONTAINS CHEMICALS INCLUDING LEAD WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM ZS WARNING A RISK OF FIRE OR ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT REMOVE THE BOTTOM COVER NO USER SERVICEABLE PARTS ARE INSIDE REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY TABLE OF CONTENTS Using Touch s T714C Brewing System PART 1 SET UP ISNT HIN Sienaan a ETE adb ca cess seite utes A a AT sntstehap vexed a N stones 5 Unpacking Instructions 5 giisredg lg 6 PART 2 BREWING A CUP Setting Up Yo r BreEWET Ready to Brew Your First Cup y Stopping the Brew PLOCESS ieinter M M ME Brewing Iced Beverages rrr eee tn nnt E TTN AAE RR XR ERE Naai EaP eT SEa erneut at PART 3 MAINTENANCE Cleaning the top MCCS e sets Cleaning the Red Cup Holder Cleaning ithe two bottom needles ettet rer rtr rh nee cuter shaves enar ex E ELI neo Fe Caa ia Ia 13 PART 4 TROUBLESHOOTING tnnt aa aS oko KE Vat aa EFE RE RE FEE REFERRI pd 14 PART5 ioni paqm T
15. oam and place it upright on a flat steady surface Lift plastic bag off of the brewer Record the serial number for this brewer The serial number can be found on the bottom of the brewer Place the brewer upright on a flat steady surface 0 100 oN A We recommend you save all packing materials in case future shipping of the product is necessary WARNING Keep all plastic bags away from children Touch Coffee amp Beverages is NOT affiliated with Keurig Inc Keurig amp and K Cup are register trademarks of Keurig Inc PART 1 SET UP Product Features T714C Brewer parts QO Cover o Cover Handle Red Cup Holder Deep Well e Housing Q Power Cord Drip Tray Slots Qo Drip Plate o Drip Tray Water Tank Q Water Inlet Adapter Controls and Indicators Power Button V Low Water Indicator Qo Brewing Indicating Light Q9 6 oz Button Q 8 oz Button 10 oz Button Qo 12 oz Button S 14 oz Button MILD Taste Button MED Taste Button BOLD Taste Button Latch kd 9 D b D MED BOLD PART 2 BREWING A CUP Setting Up Your Brewer IMPORTANT DO NOT use the brewer until it has been set up for its first use NOTE If the brewer has been exposed to temperatures below freezing allow the brewer at least two hours to reach room temperature before using it A frozen or extremely cold brewer may not operate properly 1 Unwrap the electr

Download Pdf Manuals

image

Related Search

Related Contents

Minka Lavery 5741-206 Installation Guide  Operating Instructions Titration Unit TitroLine easy  取扱説明書 - 日立の家電品  Experiment  Element Electronics ELE E850PD User's Manual  Mode d`emploi 100112 7084462    CCD English manual  Manuale tecnico Planux kit bifamiliare Art. 8172IP Technical manual  Téléchargement du guide utilisateur ZTE-F160  

Copyright © All rights reserved.
Failed to retrieve file