Vinotemp VT-WINEDISP2 Use and Care Manual
Contents
1. A PROUD HERITAGE OF EXPERIENCE amp QUALITY 09 ee oe oo 2 BOTTLE WINE DISPENSER DISPENSER amp PRESERVER VT WINEDISP2 OWNER S MANUAL WWW VINOTEMP COM SERVING WINES Storing wines at the proper temperature is important To preserve them as long as possible wine should be stored at approximately 55 Fahrenheit However the chart below suggests the optimal drinking temperature for the different styles of wine E Wine Style 19 66 Armagnac Brandy Cognac Full Bodied Red Wines Shiraz 17 62 Tawny Port 18 64 15 59 Medium Bodied Red Wines 14 57 Amontillado Sherry 13 55 Light Bodied Red Wines 12 54 Full Bodied White Wines 11 52 Medium Bodied White Wines Rose Light Bodied White 29 a Wines 9 48 Vintage Sparkling 8 46 Fino Sherry 7 45 Non Vintage Sparkling WWW VINOTEMP COM General Operating Instructions Remove all external and internal packaging from your appliance Be sure that all parts have been included before discarding any packaging materials You may want to keep the box and packing materials for use at a later date Upon receipt and inspection of unit the supply cord must be replaced if it is damaged Contact our customer service at 1 800 777 8466 or info vinotemp com NOTE Before connecting your wine dispenser to the power source let the unit stand upright for 24 hours This will reduce the possibilit2. remedy is limited at Seller s option to repair or replace defective part s with either new or factory reconditioned part s Purchaser is responsible for shipping the unit pre paid to designated facility and Seller will pay return shipping charges in the continental United States for items repaired under warranty within 12 twelve months from date of sale Since the natural variation in texture density grain color tone and shade of wood is unavoidable Seller does not guarantee the texture color tone or shade of the wood nor does seller guarantee the colorfastness of wood or against peeling chipping cracking or scratching Note Unfinished wood is subject to warping all wood surfaces must be sealed before placing cellar into service Improper placement of the unit will void the warranty By Vinotemp in writing any third party repair facility must be pre approved before providing parts free of charge This limited warranty does not cover damage due to such things as accident misuse abuse mishandling neglect acts of God fires earthquakes floods high winds government war riot or labor trouble strikes lockouts delay of carrier unauthorized repair or any other cause beyond the control of the Seller whether similar or dissimilar to the foregoing Seller is not responsible for any damages caused to Purchaser s property resulting from the good This limited warranty applies only inside the Continental US Alaska Puerto Rico and Hawaii a
3. e humidity variations temperature variations leaks fire water damage mold mildew dryness and similar and any other perils that might occur Seller is not responsible for incidental or consequential damages and there are no warranties expressed or implied which extend beyond the Limited Warranty described above The implied warranties of merchantability and of fitness for a particular purpose are hereby expressly disclaimed Some states do not allow the exclusion of incidental or consequential damages or a waiver of the implied warranties of fitness and or merchantability so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Seller disclaims any indemnification for claims of infringement of any intellectual property of protectable nature In the event of any dispute between Seller and Purchaser arising out of or relating to these terms and conditions or to the goods sold generally Purchaser must first file a written claim with Seller within ten days of the occurrence giving rise to the claim and wait an additional thirty days for a response before initiating any legal action The sale and all terms are subject to California law Any legal proceeding arising out of or relating to these terms and conditions or to the goods sold generally shall be brought solely and exclusively in the County of Los Angeles In no event may Purchaser initiate any lega
4. enser before cleaning or performing maintenance Never use harsh cleansers or scouring pads to clean any part of the wine dispenser Cleaning To clean the stopper dispenser and solenoid valve 1 Fill a bottle with clean warm water and place the stopper dispenser onto the bottle 2 Press and hold the button to begin dispensing the warm water 3 To start the automatic cleaning setting press the portion button 5 times and then hold until the display begins to flash and shows CL 4 Continue to dispense and flush the system until dry argon comes from the spout WWwW VINOTEMP COM CIRCUIT DIAGRAM Gas cartridge gt y gi Wine tube Gas tube Gas valve Wine bottle Wine solenoid _ Nine spout valve B Safety valve Wine tube Gas valve B gt Wine bottle Gas valve A Gas tube Wine bottle Gas regulator lt ii Wine spout Wine solenoid valve A Gas cartridge 17621 South Susana Road Rancho Dominguez California 90221 11 info vinotemp com PROBLEMS WITH YOUR WINE DISPENSER Most common problems can be solved easily saving you the cost of a possible service call Try the suggestions below to solve the problem before contacting Vinotemp at info vinotemp com TROUBLESHOOTING Dispensing System Complaint Possible Causes Response One canister only a Canister gasket unaligned bad a Ali
5. gn change or install the gasket dispensing 1 or 2 missing bottles gas b Canister not tightened b Turn the canister clockwise all the way leaking escaping c Gas tube broken c Change the gas tube d Gas tube not tightened at the d Check for these connections regulator or valve e Regulator leak e Check for gas escaping at the regulator f Gas valve stuck open f If gas continues to escape from the gas tube check for gas valve and wirings g Bottle not tightened g Check the plug fixer Unit not dispensing a Argon Nitrogen leak a If none of the spouts dispense wine check for canister pressure gauge or turn the canister slightly counter clockwise to see if any gas escapes turn clockwise to re tighten then check for gas leaking as instructed above b Defective pressure regulator b If none of the spouts dispense wine and the canister has pressurized gas check the regulator c Bottle neck not tightened or c Press dispense button to check if gas is defective plug escaping from the plug or fixer d Defective gas solenoid valve or d Press the dispense button to see of gas is incorrect wiring escaping out of the gas tube e Defective wine solenoid valve or e Switch the questionable valve to a working incorrect wiring spout and check to see if problem still exists f Check all wirings and connections f Incorrect or loose wirings defective power board or control board Dispensing a Argon Nitrogen low a Ifall spouts are dispensing wine sl
6. h just the touch of a button temperature display temperature amp portion setting light switch amp portion calibration temperature setting wine dispensing button top panel cleaning button Stainless stee ace panel spout side panel bottle fixer anti UV door Voltage 120V Freguency 60 Hz Cooling Power 85W Refrigerant R134a Protection Class I Adjustable Temperature Range 45 65 F 7 18 C Ambient Temperature Range 45 90 F 7 32 C Bottle Capacity 2 Maximum Bottle Shelf Life 45 days Approx Dimensions W x D x H 9 3 x 16 28 x 20 7 NOTE Argon and nitrogen gas cartridge gas weight of approximately 14 grams not included Suitable standard gas cartridges are non refillable and have a threaded neck size of 20 and minimum length of 0 5 The cartridge must have a diameter not exceeding 1 75 and a length not to exceed 5 5 17621 South Susana Road Rancho Dominguez California 90221 info vinotemp com INSTALLATION INSTRUCTIONS Before Using Your Unit Remove all packing material before using your wine dispenser Check to be sure the appliance is in good condition Use a soft dry cloth to wipe down the outside of the wine dispenser thoroughly Before connecting your wine dispenser to the power source let the unit stand upright for 24 hours This will reduce the possibility of a malfunction in the cooling system from handl
7. ician to check for restrictions Noisy operation Installation area not firm a Make sure unit is level and on flat solid surface b Screws nuts and metal parts may be loose Fan blade is hitting other parts d Fanis faulty e Compressor is faulty b Check to see if the noise is coming from the fan mount compressor mount or loose tubing c Check the blade clearance d Check to see if the fan blade is broken or if the motor is making noise e Call customer service 17621 South Susana Road Rancho Dominguez California 90221 13 info vinotemp com WWW VINOTEMP COM TERMS OF SALE AND WARRANTY Vinotemp International Seller and the person or entity that acquires these goods from Seller Purchaser hereby fully agree to the following terms and conditions of the sale Shipping fees are the responsibility of the Purchaser whether freight prepaid or freight collect Seller assumes no responsibility for the goods sold to the Purchaser once the goods have left the Seller s premises including but not limited to late delivery by the moving carrier or for events caused by any difficulty carrier incurs in attempting to fit the goods into the Purchaser s place of business or residence due to the size of the goods or otherwise Purchaser assumes all responsibility for delivery payment of freight access measurement installation hook up wiring moving and storage of the goods The tran
8. inances It is the personal responsibility of the consumer to have the proper 3 prong wall receptacle installed by a qualified electrician DO NOT UNDER ANY CIRCUMSTANCE REMOVE THE POWER CORD GROUNDING PRONG separate adequately fused and grounded circuit should be available for this appliance Do not remove any grounding wires from individual components while servicing unless the component is to be removed and POWER SUPPLY CORD replaced It is extremely important to WITH 3 PRONG replace all grounding wires when GROUNDING PLUG components are replaced DO NOT USE A GROUND FAULT INTERRUPTER GFI A DEDICATED 15 AMP CIRCUIT IS HIGHLY RECOMMENDED Electrical Cord We strongly recommend against the use of an extension cord However if you still elect to use an extension cord it is necessary that it be a properly rated UL listed 3 wire grounding type appliance extension cord with a 3 blade grounding plug and a 3 slot receptacle GE WWW VINOTEMP COM PARTS AND SPECIFICATIONS This refrigerated wine dispenser displays stores and dispenses 2 opened wine bottles keeping them fresh from oxidation for up to 45 days Wines be maintained at a chosen storage and serving temperature between 45 and 65 F NSF approved plastic components sanitary stainless steel spouts and electronic valves keep wines clean and prevent any drips from spouts Easily dispense a perfect glass of wine at any time wit
9. ing during transportation Locating Your Unit The wine preserver dispenser is designed for free standing installation only It is recommended that this unit be kept in a location with an ambient temperature range of 45 F 90 F Not intended for garage or basement installation Place your wine dispenser on a solid level surface other than carpet This will ensure vibration and noise free operation Use the adjustable legs to ensure that the unit is level Leave 5 inch clearance on all sides of the unit This is to ensure proper circulation OPERATING YOUR WINE DISPENSER Loading Unloading Argon Nitrogen Inert Gas Bottle 1 Press and hold the wine dispensing button to empty the remaining gas in the cartridge Unplug the unit Rotate the cover upwards to access the gas cartridge Pull the cartridge and turn it counter clockwise to loosen Place a new cartridge and align it to the neck thread of the regulator To properly position the cartridge rotate once clockwise and once aligned continue to turn clockwise to tighten 6 Move the cartridge back and close the cover amp Note It is normal that a little gas escapes when the gas cartridge is being tightened to the regulator open cover COM Attaching and Removing Wine Bottles Unscrew lower part of bottle fix nut and place it on the neck of desired wine bottle Slide bottle upward with gas and wine tube inside
10. l proceeding more than six months after the occurrence of the event giving rise to the dispute The above terms and conditions are the only ones governing this transaction and Seller makes no oral representations of any kind These Terms and Conditions can only be modified in writing signed by both Purchaser and Seller 05 12 SERVICE amp IMPORTANT NOTICE Upon receipt and inspection of unit the supply cord must be replaced if it is damaged Contact our customer service at 1 800 777 8466 or info vinotemp com The manufacturer has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice WARNING Please do not place the unit within reach of children For adult use only Contact info vinotemp com with any questions or visit www vinotemp com 17621 5 Susana Road Rancho Dominguez CA 90221 www vinotemp com Vinotemp is a registered trademark of Vinotemp International All products features and services are subject to change without notice We cannot guarantee the accuracy of the contents of this document We disclaim liability for errors omissions or future changes 2012 Vinotemp International All rights reserved 17621 South Susana Road Rancho Dominguez California 90221 17 info vinotemp com
11. le Causes Response Unit not running a Power cord unplugged b Power switch off a Check the power cord b Turn the switch on it will light up when power is on c No power to the outlet c Check for power at the outlet and fuse d Incorrect and loose wirings d Check the wirings and connections at the power switch and power board Unit running high a Improper door seal a Check the door opening and gasket temperature or b Ambient temperature is too high b Check the installation location continually c Improper condenser air flow d Refrigeration system problems c Check the fan and clearance d Call customer service Temperature is too a Temperature setting is too high a Lower temperature setting high b Displayed temperature is correct but inside temperature is high b Temperature sensor is touching the cold panel Temperature is too low a Temperature sensor is faulty a Insert the sensor in a cup of iced water to see if it displays 32 F b Unit is iced b Unplug unit to defrost c Power board is faulty c Change the power board d Display Control board is faulty d Change the display control board Compressor running a Poor evaporator air flow a Check for any restrictions but not cooling b Faulty evaporator fan b Check to see if the fan is turning c Refrigerant leakage c Call service technician to check for lass of refrigerant d Refrigeration system restricted d Call service techn
12. owly check interrupted or slow the gas pressure and install a new canister if necessary b Gas tubes kinked or twisted b Press dispensing button to see if gas is escaping out of the gas tube slowly c Bottle neck not tightened c Check the bottle plug and fixer for escaping gas d Gas solenoid valve restricted d Remove bottle press dispensing button to see if gas is escaping out of the gas tube e Wine solenoid valve restricted e Switch the to a working spout to check Wine spurting or a Wine tube is restricted a Check for any restrictions spitting b Bottle is near empty and there is b Change the empty wine bottle out for a full too much gas in the bottle one c Gas pressure is too high c Replace the pressure regulator d Wine solenoid valve is dirty d Clean solenoid valves W COM Dispensing System Complaint Possible Causes Response Wine dripping a Solenoid valve seat leak a Check for debris if constant dripping use warm water to flush the system b Spout loose b Push the spout to tighten if there is intermittent dripping a Wine tube leak a Check the wine tube b Spout loose b Push the spout to tighten c Empty bottle c Change the empty bottle out for a full bottle Wine divided a Debris in spout a Clean out debris Too many bubbles a Argon Nitrogen pressure is too high a Replace the pressure regulator Cooling system Complaint Possib
13. r decrease the portion control settings in 1 02 increments until you reach your desired setting Calibrating the portion If the amount of wine dispensed varies additional calibration may be used to correct the dispensed portion of wine To calibrate the portion control setting press and hold the 9 button until the display shows and the previously set portion control amount begins to flash Using the buttons you can increase or decrease the portion control settings if necessary Once you have checked the portion control setting press the button to dispense wine and verify the amount poured Note You may need to repeat this procedure several times until the correct portion is dispensed 17621 South Susana Road Rancho Dominguez California 90221 info vinotemp com Setting the Temperature The temperature display will show the current temperature inside the unit To set a temperature press and hold the button till the display shows H1 and the displayed temperature starts to flash Once the temperature display starts to flash use the 4 or buttons to select your desired temperature For wine to stay fresh up to 45 days bottles must be closed and unit preservation system must be properly sealed to prevent deterioration Keep wine at proper temperature in unit LED Light The LED light can be switched on or off by pressing the 9 button CARE AND MAINTENANCE IMPORTANT Always unplug your wine disp
14. rate play with or crawl inside the appliance Keep packing materials away from children Do not clean appliance with flammable fluids Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance The fumes can create a fire hazard or explosion To clean only use mild detergents or glass cleaning products Do not use solvent based cleaning agents or abrasives Do not operate with housing panels removed or damaged When disposing of refrigerated appliances special handling is often required It is the consumer s responsibility to comply with federal and local regulations when disposing of this product Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual All other servicing should be referred to a qualified technician Locate the unit away from direct sunlight and sources of heat stove heater radiator etc Do not use this appliance for other than its intended purpose Do not store food in cabinet Do not place any other appliance on top of the unit For adult use only Do not lift or carry the wine dispenser by the cord Do not plug in to the power socket before setup is complete When positioned or if moving the appliance ensure that it is not set horizontally positioned at an angle of more than 45 or turned upside down Place the appliance on a solid level surface Allow for proper clearances on all side
15. re not warranted For Non New Units Scratch amp Dent Refurbished Floor Models warranty for compressor units is 90 days from your dated invoice and 30 days for thermoelectric units parts for function only not cosmetic defects These units are refurbished and sold as is Purchaser assumes risks to the quality and performance of goods and assumes the costs of all necessary service or repair not covered herein For Element Grills via Element Products LLC grills have a 1 year comprehensive parts warranty on entire product Three years limited parts warranty covering the stainless burner and a thirty day limited parts warranty on grill accessories If grill is defective and unused plus all packaging and parts are intact we will either replace the grill or provide service to repair the grill Returned product must accompany all original packaging and parts and is subject to our 35 restocking fee and freight both ways With Wine Mate products if the customer calls and the product is defective you must obtain a letter from your qualified refrigeration technician at the customers cost to verify that the unit was installed properly with proper ventilation and the unit is truly malfunctioning due to manufacture defect Purchaser understands and acknowledges that the goods sold here are wine cellars cigar humidors and or other similar units which house wine or cigars Purchaser assumes all risk of using these units including risk of spoilag
16. s payment on a check or credit card for any reason Purchaser agrees to pay for all costs associated with the Seller s collection or litigation of such a claim including without limitation extra damages court costs and attorneys fees Finance charges begin the date of invoice Collection fees plus NSF fee of 50 will be added to your invoice which you agree to promptly pay Title to the goods does not pass until payment is received in full by Seller and Seller retains a security interest in the goods until they are paid for in full LIMITED WARRANTY Seller warrants that the goods will be free of defects in materials and workmanship as follows Furniture style wood wine cabinets all cooling unit parts for a period of 5 five years cabinetry and labor uninstalled for a period of 12 twelve months from date of sale For the metal cabinet wine units parts and labor for cooling system and cabinetry for a period of 12 twelve months from date of sale Thermoelectric Units 90 ninety days from the date of sale including Wine Coolers Beer Dispensers Humidor Portofino Wood Cellars and Refrigerators Wine Mate Split Systems and installed products are parts only for 1 year no labor Other Wine Mate Cooling Systems are 5 years parts 1 year labor Wine Accessories and Racking Systems are not warranted There is no warranty on parts purchased separately Removal and re installation of unit is not included in warranted labor Purchaser s exclusive
17. s of the unit The wine dispenser is an electrical appliance To avoid injury or death from electrical shock do not operate the unit with wet hands while standing on a wet surface or while standing in water Allow unit to stand upright for 24 hours prior to first plugging it in This unit is designed for indoor household use only Any other use will void the warranty WARNING Risk of child entrapment and suffocation Before you throw away this or an old unit take off the door Leave the shelves in place so that children may not easily climb inside WARNING Gas bottle contents under pressure Do not puncture or incinerate Keep away from heat and out of direct sunlight Keep away from sharp objects that could puncture chamber Do not store in an enclosed vehicle Do not discharge towards face or body KEEP OUT OF REACH OF CHILDREN 17621 South Susana Road Rancho Dominguez California 90221 info vinotemp com ELECTRICAL CONNECTION A WARNING ELECTRIC SHOCK HAZARD Disconnect electric supply from appliance before servicing Replace all panels before operating Failure to do so could result in death or electrical shock To avoid the risk of electrical shock property damage personal injury or death The power cord must be plugged into 3 prong grounding type wall receptacle GROUNDING TYPE grounded in accordance with the National Electrical Code ANSI NFPA 70 latest WALL RECEPTACLE edition and local codes and ord
18. sportation of all goods is subject to the terms and conditions which the moving carrier imposes on Purchaser including but not limited to additional charges imposed per flight of stairs and or additional charges resulting from the 5 inability to safely and or adequately use the building elevator to lift the goods to an upper floor Any claim for damages incurred during shipment by the carrier of the goods are insured and handled directly with the carrier and must be noted at time of delivery Any damages due to manufacture defects will be handled directly with Vinotemp International subject to the limited warranty All sales are final and unless authorized in writing by the Seller Purchaser may not return the goods under any circumstance If Purchaser refuses to accept the goods under any circumstance the Purchaser is liable for the return and cost of freight both ways and if Seller does take back the goods there will be a restocking service fee that is 35 of the purchase price of the goods Product must be in original packaging Built to Order products including Cabinets Racking and Accessories are non returnable Purchaser must notify Seller of non conforming goods within four days of delivery after which time all goods are deemed accepted If an order has been placed and production has started cancellation of your order will be a 15 charge If Purchaser tenders payment with a check that has insufficient funds NSF or stop
19. the bottle Fit bottle mouth into silicon plug If bottle mouth is larger lift upper part of bottle fix nut to free silicon plug completely and ease bottle mouth into the silicon plug first Tighten lower part of bottle fix nut to the upper part Press the dispensing button to allow wine out and check to see if gas leakage will occur Reconnect tighter if needed so gas does not escape Place wine fully in refrigerated cabinet and close door BOTTLE FIX NUT SILICON _ PLUG GAS TUBE WINE TUBE SEE WINE POWER 8 BOTTLE SWITCH i Once the wine dispenser is positioned and plugged in turn the power on vo 0 Dispensing Wine The wine dispenser features two sets of two dispensing buttons each positioned directly above its corresponding wine bottle spout The two dispensing button options are Press and hold the button over the desired spout to begin dispensing wine into your glass Wine will continue to be dispensed until the button is released Press the 2 button to dispense wine 102 increments Press it once to dispense 10z twice to dispense 20z and so forth Resetting the 1 portion control setting The 1 preset portion control setting can be reset by the user To set the portion control press and hold the button until the display shows H2 and the previously set portion amount begins to flash Using the 2 or 7 buttons you can increase o
20. y of a malfunction in the cooling system from handling during transportation READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Save these instructions To register your product visit http www vinotemp com Warranty aspx Register your warranty within 10 days of receiving the unit Please be sure to retain your proof of purchase 17621 South Susana Road Rancho Dominguez California 90221 info vinotemp com TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS diate ces 5 ELECTRICAL CONNECTION PARTS AND SPECIFICATION Sia 7 INSTALLATION INSTRUCTIONS 8 OPERATING YOUR WINE DISPENSER a 8 AND MAINTENANGE 10 CIRCUIT DIAGRAM 11 TROUBLESHOOTING GUIDE 12 TERMS OF SALE AND 14 IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire electrical shock or injury when using your appliance follow these basic precautions Read and follow all instructions before use Do not operate this or any other appliance with a damaged cord Always unplug the appliance before performing any care or maintenance Exercise caution and use reasonable supervision when appliance is used near children Never allow children to ope
Download Pdf Manuals
Related Search