PULSE Showerspas 1028 Installation Guide
Contents
1. PULSE SHOWERSPAS Lanikai ShowerSpa Model 1028 CH Owner s Manual Lanikai ShowerSpa Installation Instructions BEFORE YOU BEGIN Measure the following to ensure your Lanikai ShowerSpa will fit properly 1 Center of existing shower arm to top of valve trim ring Minimum 2714 69 8cm required 2 Center of existing shower arm to top of ceiling Minimum 10 25 4cm required MINIMUM CLEARANCE Ceiling rm Trim Ring M o Shower Valve D 25 4cm 27 69 8cm Ar Parts and Tools Required Please lay out and become familiar with all parts prior to assembly Read all instructions once before beginning and contact Customer Support if you have any questions at 1 888 785 7320 8 30 am 5 00 pm pacific time Monday Friday or email support pulseshowerspas com For more information visit www pulseshowerspas com lanikai A Shower Arm 1 N Teflon Tape 1 B Top Tee 1 O Optional Screws 2 C Inlet Fitting 1 P Optional Wall Anchors 2 D 2 NPT Brass Nipple 1 Q 2 5mm Allen Wrench 1 E Shower Pipe 1 R Actuator F Escutcheon 2 R 1 Actuator Housing G Lower Mount w Tape 1 R 2 Actuator Piston H Shower Head 1 R 3 Brass Fitting I Hand Shower 1 S Diverter J Flexible Hose 1 S 1 Cartridge K Set Screw 1 S 2 Retaining Nut L Set Screw 2 S 3 Handle M Rubber Washer 4 1 extra Tools Required Adjustable Wrench Pencil Allen Wrench 2 5mm supplied Level option2. completely dry Remove covering of two face tape and reposition Lower Mount G to mark so the optional mounting holes are horizontal Apply pressure to mount for 30 seconds by push ing firmly against the Diverter To ensure proper adhesion allow one hour before using your ShowerSpa and keep area around the mount as dry as possible for the first 24 hours Tape will be fully cured after 24 hours OPTIONAL Secure Lower Mount G with permanent wall anchors Mark hole locations in Lower Mount Drill 144 deep holes using 6mm 1 4 masonry tile drill bit Insert Wall Anchors P and secure Lower Mount with Screws O CAUTION LIVE PLUMBING IN WALL 10 Position Shower Pipe E parallel to wall by adjusting Diverter on Lower Mount G Secure Diverter to Lower Mount with Set Screw L 11 Insert Rubber Washer M into both ends of Hose J Con nect hex head end to outlet on Diverter and tapered end to Hand Shower I Place Hand Shower I into Holder 12 Insert Rubber Washer M in Shower Head H and tighten securely to Shower Arm A Flow Restrictor Information This unit contains flow restrictors limiting flow to 2 5 gallons per minute If the flow rate is less than expected or reduces over time you may have an obstruction at the inlet restrictor To check for debris remove shower unit from wall exposing the Inlet Fitting C attached to wall Using needle nose pliers rotate C clip until one end enters the cut
3. use ShowerSpa as a support device Do not use harsh chemicals or abrasives when cleaning Turn water supply off when servicing your ShowerSpa Pulse Showerspas Inc 49 Hangar Way Suite A Watsonville CA 95076 888 785 7320 info pulseshowerspas com www pulseshowerspas com support pulseshowerspas com Part 1028 CH OM ENG Rev Y2013 03 05
4. al Drill with 6mm 44 masonry bit optional Flashlight optional Nut S Lanikai ShowerSpa Installation Instructions Congratulations on your purchase of the PULSE Lanikai Rain Shower system There s no better way to start your day Follow these simple steps in the order presented to help avoid mistakes When finished multiple soothing showering options are at your fingertips Assembly and installation of the Lanikai Rain Shower System is designed to be quick and easy If you have any installation questions or performance problems call PULSE Customer Service toll free at 1 888 785 7320 8 30 am 5 00 pm pacific time Monday Friday or email support pulseshowerspas com before returning this product to the store FOR NEW CONSTRUCTION OR COMPLETE REMODEL e A hot cold Automatic Compensating Shower Valve which complies with ASSE 1016 2011 ASME A112 1016 2011 CSA B125 16 11 is required NOT INCLUDED e Nipple should extend no more than 1 2 past finished wall surface 1 Determine the length Nipple D needed a Place mark on existing shower arm at wall surface Unscrew shower arm from elbow in wall b Measure distance from mark on shower arm to end of shower arm threads Add 14 to this measurement and then round to nearest 1 2 Example 1 If measurement 114 add 1 2 134 rounded 2 NPT nipple this is the length needed Example 2 If measurement 1 add 14 214 rou
5. ing functions Change the angle of spray by pushing the jet left right up or down Adjust hand shower height by depressing button on holder and sliding it up or down Always turn cold water on first to help prevent any accidental burning or scalding especially for children and elderly Do not use any part of the Lanikai Rain Shower System as a support device ULSE SHOWERSPAS To keep your ShowerSpa looking new wipe down after each use with a soft cotton cloth Protect your ShowerSpa from hard water stains and mineral deposits by periodically using an auto spray wax Clean using mild liquid soap and a non abrasive sponge or cloth Rinse with clean water Do not use any kind of chemicals or abrasives If the flow rate of your ShowerSpa is less than expected reduces over time or functions are not completely independent the actuator can be removed to clean sediment Please CALL TECH SUPPORT 1 888 785 7320 8 30 am 5 00 pm pacific time Monday Friday and we will be happy to assist you Manufacturer s Warranty PULSE Shower Spas Inc warrants that all ShowerSpas are free from defect in workmanship and or materials for a period of three years from the date of purchase This warranty extends to the original purchaser only and is non transferable This warranty does not cover and PULSE ShowerSpas will not pay for conditions malfunctions or damages resulting from 1 normal wear and tear improper installation whethe
6. nded 2 NPT nipple this is the length needed IMPORTANT If existing shower arm is located above the tile fiberglass wall surface you must add the distance from the sheetrock to face of the tile fiberglass shower wall to the above measurement NOTE If supplied 2 Nipple D is not the correct length based on above formula you must obtain the correct size sold separately Various length NPT brass nipples are readily available at most hardware stores 2 Apply a generous amount of Teflon Tape N to both ends of the Nipple D 3 Hand tighten Inlet Fitting C onto Nipple D then Nipple to fitting in wall Use adjustable wrench on the Inlet Fitting to tighten both connections simultaneously Continue tightening until both connections are secure with no leaks 4 Connect Top Tee B into Shower Pipe E and align with Diverter Make sure Top Tee is fully seated into Shower Pipe and secure with Set Screw K 5 Slide Shower Arm A into Top Tee B and hand tighten Retaining Nut until secure 6 Slide Top Escutcheon F over Top Tee B then slide Bottom Escutcheon F over Diverter 7 Loosen Set Screw L on Diverter slide Lower Mount G into Diverter and tighten set screw Do Not Expose Tape 8 Push Top Tee B over Inlet Fitting C until flush against fit ting Position Diverter so Shower Pipe E is plumb vertical Mark location of Lower Mount G with pencil 9 Wall surface must be clean of any residue and
7. out section of the fitting then pull the C clip out completely With needle nose pliers gently depress the inner yellow ring of the restrictor to expose the white spindle Hold the spindle with pliers and pull toward you to remove Remove the screen and turn cold water on SLOWLY Run water for 15 seconds to remove debris from water line Check screen and restrictor for sediment Use water and a soft nylon brush if necessary to remove sediment When finished first replace the screen then the restrictor and finally the C clip The Shower Head H and Hand Shower are equipped with flow restrictors limiting flow rate to 2 5GPM 9 5LPM as per the standard ASME A112 18 1 CSA B 125 1 Your Lanikai Showerspa is fully functional with or without the restrictors Depending on your local plumbing codes the restrictors may or may not be necessary AP Usage Diverter valve controls the shower head handheld shower and body spray functions Turn diverter knob right or left to the de sired setting The diverter will click into place at each function The shower arm height is adjustable by sliding the arm up or down while holding the shower pipe with your free hand The arm also swings freely to the left or right by gently pressing on the arm or shower head Rotate face of hand shower to switch settings and rotate holder forward or back to adjust angle Rotate body jets 14 turn left or right to select stimulating or sooth
8. r performed by a contractor service company or the consumer improper maintenance misuse abuse negligence accident or alteration 2 the use of abrasive caustic or no rinse cleaning agents 3 the use of the product in any manner contrary to the product instructions 4 conditions in the home such as excessive water pressure or corrosion Should any ShowerSpa be determined by PULSE ShowerSpas Inc to be defective in normal residential use at the option of PULSE ShowerSpas Inc such product shall either be replaced or repaired and returned to the customer free of defects The consumer shall give notice of any defects to PULSE ShowerSpas Inc within thirty days of discovery of such defect Proof of purchase original sales receipt must be provided to PULSE Shower Spas Inc with all warranty claims PULSE ShowerSpas Inc is not responsible for labor charges removal charges installation or other consequential costs In no event shall the liability of PULSE ShowerSpas Inc exceed the purchase price of the ShowerSpa Some states provinces do not allow limitations of how long an implied warranty lasts or the exclusion or limitation of such dam ages so these limitations and exclusions may not apply to you This warranty gives the consumer specific legal rights You may also have other rights that vary by state province Follow manufacturers recommended installation Use caution with children under ten years of age Do not
Download Pdf Manuals
Related Search