Wagner 0529002 Use and Care Manual
Contents
1. e Spray parallel to the surface with smooth passes at a consistent speed as illustrated below Doing this will help avoid irregularities in the finish i e runs and sags Even coat throughout r 6 to 12 inches Correct Keep stroke smooth and at an even speed e Always apply a thin coat of material on the first pass and allow to dry before applying a second slightly heavier coat e When spraying larger surfaces overlap each spray pass by at least 50 This will ensure full coverage e When spraying always trigger the spray gun after spray pass has begun and release trigger before stopping the pass Always keep the gun pointed squarely at the spray surface and overlap passes slightly to obtain the most consistent and professional finish possible Light coat Heavy coat IT Incorrect Do not flex wrist while spraying Note When you quit spraying for any length of time unplug the spray gun When you restart wipe the nozzle with a damp cloth to remove any dried paint Wagner Spray Tech All Rights Reserved Pattern Examples Use the images and guidelines below in order to assist you in achieving the desired spray pattern for your project These are meant to be general starting points you may have to slightly modify certain controls on the system in order to get the exact performance you need Large Surface Projects Generally high material flow is needed for spraying large surface ar2. Technique properly masked in order to prevent overspray from covering woodwork floors or furnishings Make sure you have properly masked the room per the instructions on the enclosed Taping Guide If spraying with an air assisted spray system is new or unfamiliar to you it is advisable to practice on a piece of scrap wood or cardboard before beginning on your intended workpiece and or test with water s The room you are spraying must be Surface Preparation All objects to be sprayed should be thoroughly cleaned before spraying material on them Areas not to be sprayed may in certain cases need to be masked or covered Spray Area Preparation The spray area must be clean and free of dust in order to avoid blowing dust onto your freshly sprayed surface How to Spray Properly It is important to keep your arm moving whenever the gun is being triggered If you pause or linger in one spot too long too much material will be sprayed to the surface Partially pulling the trigger will start the turbine but no material will spray until the trigger is pulled fully It is recommended that the trigger first be pulled partially in order to start the turbine before a spray pass is made e Position the spray gun perpendicular to and six 6 or more inches from the spray surface depending upon the spray pattern size desired With reduced material flow and air power you can get closer to the spraying surface
3. eas such as walls and decks e The air cap position will determine the movement direction of the spray gun Technique Small Surface Projects Generally low material flow is needed for spraying smaller surface areas such as corners lattice or spindles e Ifyou feel the material is going on too thin increase the material flow e Ifyou feel the material is going on too thick decrease the material flow even further or move the spray gun further away from the surface Note If after following the guidelines on these two pages you are still not getting the spray performance you need refer to the Troubleshooting section on page 14 Besides adjusting the controls other factors that should be considered when spraying e Distance from the spray object if you are too far from the spraying surface the material will go on too thin and vice versa e Material thickness if the spray pattern runs and or is too splotchy the material may need to be thinned Note Only thin the material if absolutely necessary to improve spray performance Optimal spray performance should be acheived simply by adjusting the various controls on the unit Spray gun movement moving the gun too quickly will cause the spray pattern to be too thin and excess overspray Moving the gun too slowly will cause the spray pattern to be too coarse or thick Wagner Spray Tech All Ri
4. eft over in the system Pull the trigger so that the material inside the spray nozzle drains back into the container IMPORTANT If you cleaned the sprayer using mineral spirits repeat steps 1 6 using warm soapy water Move on to Cleanup Cleaning the Nozzle next page Empty waste container 10 Wagner Spray Tech All Rights Reserved Cleaning the Gun To Clean the Nozzle iP Make sure power cord is unplugged Push the tab below the trigger twist and separate the spray gun from the turbine Wipe the exterior of the cup and gun until clean Remove the adjustment ring a carefully from the connecting nut b Loosen the connecting nut Remove the parts as shown Clean all parts with a cleaning brush and the appropriate cleaning solution Clean the air vent c on the suction tube with a soft bristled cleaning brush Clean the rear of the nozzle d with the appropriate cleaning solution Use a thin layer of petroleum jelly to lubricate the O ring e To reassemble see the instructions on the next page Nozzle seal It is important that the nozzle The nozzle seal may become seal inside the nozzle be re stuck inside the iSpray or Detail installed properly Make sure the Finish nozzle when the nozzle cup side of the seal the side with is removed If this occurs make the groove is facing out towards sure to pull it out the front of the nozzle Improper installat
5. ghts Reserved Flushing the unit Before you begin When cleaning use the appropriate cleaning solution warm soapy water for latex materials mineral spirits for oil based materials IMPORTANT Never clean air cap or air holes in the nozzle with sharp metal objects Do not use solvents or lubricants containing silicone Special cleanup instructions for use with flammable solvents must have a flashpoint above 100 F 38 C e Always flush spray gun outside e Area must be free of flammable vapors e Cleaning area must be well ventilated e Do not submerge turbine To Flush the Unit 1 Unplug the power cord Loosen the material container by 1 2 turn but do not remove it This will relieve any pressure left over in the system Pull the trigger so that the material inside the spray nozzle drains back into the container 2 Unscrew the container and remove Empty any remaining material back into the material container 3 Pour a small amount of the appropriate cleaning solution into the cup Water 1 2 full Mineral spirits 1 4 full 4 Attach the cup to the nozzle and plug in the sprayer 5 Spray the cleaning solution into a safe area While spraying gently shake the spray gun This slight agitation will help break up smaller particles of spray material 6 Unplug the power cord Loosen the material container by 1 2 turn but do not remove it This will relieve any pressure l
6. ion will cause leakage and damage to the turbine Wagner Spray Tech All Rights Reserved 11 To Reassemble 1 Install the nozzle seal 1 with the groove a slot facing toward the nozzle away from the front end assembly 2 Insert the nozzle 2 Make sure to align the groove b and notch c and align the nozzle opening with the needle 3 Put the air screen d in the air cap e Put both 3 on the nozzle 2 and secure with the connecting nut 4 Note This step is easier if the spray gun is facing up 4 Snap the adjustment ring 5 into the connecting nut 4 enabling the adjustment lever f on the peg g to be positioned in the air cap Note Make sure that the two recesses on the adjustment ring are engaged in the air cap tabs 5 Reassemble the spray gun Note Make sure the air valve tube is free of paint If not clean the air valve tube by following the instructions on the next page If clean make sure it is attached securely at both ends see inset Nozzle seal DO NOT LOSE It is important that the nozzle seal inside the nozzle be re installed properly Make sure the cup side of the seal the side with the groove is facing out towards the front of the nozzle Improper installation will cause leakage and damage to the turbine 12 Wagner Spray Tech All Rights Reserved
Download Pdf Manuals
Related Search