Rust-Oleum Automotive 249415 Use and Care Manual
Contents
1. IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 800 424 LEAD or log on to www eps gov lead ENGINE PRIMER PRODUCT APPLICATION cont APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle If mixing ball fails to rattle DO NOT STRIKE CAN Contact Rust Oleum Shake often during use Hold can 12 16 from surface and spray in a steady back and forth motion slightly overlapping each stroke Keep the can the same distance from the surface and in motion while spraying For best adhesion apply ONE thin coat Do not apply a heavy coat or multiple coats of Auto Plastic Primer Do not use near open flame DRY amp RECOAT Dry and recoat times are based on 70 F 21 C and 50 relative humidity Allow more time at cooler temperatures Dries to the touch in 20 minutes and dries to handle in 1 hour Top coat after 1 hour Apply a second coat or top coat within 1 hour or after 48 hours CLEAN UP Wipe off tip when finished Clean up wet paint with xylene or mineral spirits Properly discard empty container Do not burn or place in home trash compactor CLOGGING If the valve cl2. ogs twist and pull off spray tip and rinse ina solvent such as mineral spirits Do not insert any object into can valve opening Form GDH 108 Rev 071513 TECHNICAL DATA ENGINE PRIMER PHYSICAL PROPERTIES ENGINE PRIMER Resin Type Modified Alkyd Pigment Type Titanium Dioxide Solvents Acetone Aliphatic and Aromatic Hydrocarbons MIR 1 20 Max Fill Weight 12 ounces Recommended Dry Film Thickness DFT Per Coat 1 5 2 5 mils 37 5 62 5p Practical Coverage at Recommended DFT 10 12 sq ft can 0 90 1 09 m can Dry Times Touch 20 minutes and 50 Relative Handle tO Humidity Recoat Within 1 hour or after 48 hours Dry Heat Resistance 500 F 260 C Intermittent Shelf Life 5 years Flash Point 156 F 104 C Safety Information For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice ge RUST OLEUM BRANDS Rust Oleum Corporation Fo
3. po TECHNICAL DATA ATO 55 DESCRIPTION AND USES Rust Oleum Engine Primer bonds to bare metal and helps create a smooth surface for top coat application It is formulated to prevent rust and is recommended for use on automotive engines and other automotive surfaces which reach intermittent temperatures up to 500 F 260 C For maximum protection top coat with Rust Oleum Engine Enamel Engine Primer features an advanced spray system that allows you to spray at any angle even upside down for those hard to reach areas A comfort spray tip with a wider finger pad reduces fatigue caused by continuous spraying PRODUCTS SKU 12 ounce spray Description 249410 Gray PRODUCT APPLICATION PAINTING CONDITIONS Use outdoors or in a well ventilated area such as an open garage Use when temperature is between 50 90 F 10 32 C and humidity is below 85 to ensure proper drying Do not apply to galvanized metal Do not use on metal directly exposed to flames Avoid spraying in very windy and dusty conditions Cover surrounding area to protect from spray mist SURFACE PREPARATION Wash the surface with a commercial detergent or other suitable cleaning method Rinse with fresh water and dry with a clean cloth Remove loose paint and rust with a wire brush or sandpaper until the metal surface is completely bare Lightly sand smooth and glossy surfaces WARNING If you scrape sand or remove old paint you may release lead dust LEAD
4. rm GDH 108 11 Hawthorn Parkway Phone 877 385 8155 Rev 071513 Vernon Hills Illinois 60061 www rustoleum com An RPM Company
Download Pdf Manuals
Related Search