Rust-Oleum Automotive 252467 Use and Care Manual
Contents
1. IOSH approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 800 424 LEAD or log on to www eps gov lead PRODUCT APPLICATION cont PRIMING Use of a Rust Oleum Primer provides added corrosion protection on metal and promotes adhesion and hiding A primer is especially recommended for heavily rusted or pitted surfaces Recommended primers include 249321 Primer Sealer and any of the sandable primers 249419 Red 252472 Light Gray or 249415 Gray APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle If mixing ball fails to rattle DO NOT STRIKE CAN Contact Rust Oleum Shake often during use Hold can upright 10 16 from surface and spray in a steady back and forth motion slightly overlapping each stroke Keep the can in motion while spraying Apply 2 or more light coats a few minutes apart Apply multiple coats versus applying one heavy coat Do not use near open flame DRY amp RECOAT Dry and recoat times are based on 70 F and 50 relative humidity Allow more time at cooler temperatures Dries to touch in 15 minutes and to handle in 1 2 hours Surface can be recoated within 2 hours or after 48 hours If recoating after 48 hours repeat the surface preparation steps Light wet sanding with 600 grit sandpaper is recommended The2. erials All technical information is subject to change without notice ST OLE Rust Oleum Corporation Form CS1924 Hl 11 Hawthorn Parkway Phone 877 385 8155 Rev 010813 Vernon Hills Illinois 60061 www rustoleum com BRANDS An RPM Company
3. freshly coated surface can be buffed with wax or polish after one week CLEAN UP When finished spraying clear spray valve by turning can upside down and depressing spray button for 3 5 seconds some paint will be sprayed out so be careful to not inadvertently spray yourself or other objects Clean up wet paint with xylene or mineral spirits Properly discard empty container Do not burn or place in home trash compactor CLOGGING If the valve clogs twist and pull off spray tip and rinse in a solvent such as mineral spirits Do not insert any object into can valve opening Form CS1924 Rev 010813 TECHNICAL DATA AUTOMOTIVE ENAMEL PHYSICAL PROPERTIES es C e T C Recommend Dry Film 1 0 2 0 mil 25 50 Thickness DFT Per Coat Practical Coverage 8 10 sq ft can 0 90 1 1 m can at Recommended DFT Touch 15 minutes Dry Times at 77 F 25 C 1 2h Rel Hum Fully Dry 24 hours 156F 104 C Fash Point Wanin For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective mat
4. po TECHNICAL DATA ATO 28 AUTOMOTIVE ENAMEL DESCRIPTION AND USES Rust Oleum Automotive Enamel provides a long lasting protective barrier that seals out moisture and prevents rust and corrosion Its durable formula can be applied over bare and primed metal surfaces for a smooth gloss finish Ideal for use on autos trailers RVs and auto accessories PRODUCTS 252459 Cherry Red 252461 Extreme Yellow 252462 Gloss Black 252464 Flat Black 252465 Semi Gloss Black 252467 Semi Gloss White 252468 Gloss White PAINTING CONDITIONS Use outdoors or in a well ventilated area such as an open garage Use when temperature is between 50 F 10 C and 90 F 32 C and humidity is below 65 to ensure proper drying Do not apply to surfaces when heated exceed 200 F 93 C Avoid spraying in very windy and dusty conditions Cover surrounding area to protect from spray mist SURFACE PREPARATION Remove loose paint and rust with a wire brush or sandpaper Lightly sand glossy surfaces For best results dry or wet sand with 400 grit sandpaper to feather adjacent paint surface and prepare metal Clean area to be painted with Rust Oleum Mineral Spirits to remove all oil grease wax and dirt Dry thoroughly WARNING If you scrape sand or remove old paint you may release lead dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a N
Download Pdf Manuals
Related Search