Zinsser 2008 Use and Care Manual
Contents
1. Aliphatic Hydrocarbons Glycol Ethers Water Weight Per Gallon NA 10 5 Ibs Per Liter NA 1 26 kg Solids By Weight NA 50 5 By Volume NA 34 0 Volatile Organic Compounds N A lt 100 g l 0 83 Ibs gal Recommended Dry Film 1 5 2 5 mils 1 0 2 0 mils Thickness DFT per Coat 37 5 62 5u 25 50 Wet Film to Achieve DFT NA 3 0 6 0 mils Unthinned material 75 150 Theoretical Coverage at NA 545 sq ft gal 1 mil DFT 25p 13 4 m A Practical Coverage at 10 12 sq ft an 450 sq ft gal 11 1 m il non porous Recommended DFT assume 0 9 1 1 m P 350 sq ft gal 8 6 m l porous 15 material loss Dry Times at Touch 30 minutes 35 minutes 70 80 F 21 Recoat 1 hour 1 hour 27 C and Stain sealing 2 hours 2 hours 50 Relative 24 hours over cedar 24 hours over cedar Humidity Full hardness 7 days 7 days Shelf Life 5 years 5 years Flame Spread ASTM 84 97A N A Class 1 Smoke Contribution ASTM 84 N A Class 1 97A Flash Point 156 F 104 C gt 180 F 82 C Safety For additional information see MSDS NOTE Calculated values may vary slightly from the actual manufactured material The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only2. sss TECHNICAL DATA BEY123 01 BULLS EYE 1 2 3 WATER BASED PRIMER ZINSSER QUALITY SINCE 1849 DESCRIPTION AND USES Zinsser Bulls Eye 1 2 3 is a high hide water based styrenated acrylic water based primer sealer stain blocker and bond coat designed for priming all surfaces Apply to interior and exterior walls ceilings doors trim fascia soffits foundations railings and related paintable surfaces Bulls Eye 1 2 3 bonds to wood plaster concrete gloss enamels hardboard glass and tile It provides a rust inhibitive coating on iron railings steel frames piping etc It resists the growth of mold and mildew in damp humid environments It resists high pH surfaces up to 12 5 and seals most porous surfaces Bulls Eye 1 2 3 traps most stains in the primer film including graffiti grease rust cedar and redwood tannin creosote and asphalt stains PERFORMANCE CHARACTERISTICS Designed for interior and exterior surfaces Bonds to glossy surfaces without scuff sanding Formulated with stain blocking resins Rust inhibitive may be used to prime ferrous metal Is mold and mildew resistant Fast drying Recoat in under 1 hour Sticks to all surfaces and sands easily High hiding formula blocks most stains Excellent for sealing water soluble tannin bleed on cedar and redwood e Easy soap and water clean up PRODUCTS SKU Container Size 2008 Aerosol 2004 1 Quart 2001 1 Gallon 2000 5 Gallon PROD
3. to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice T Rust Oleum Corporation Form CS2243 RU ST OLEU M 11 Hawthorn Parkway Phone 877 385 8155 Rev 100313 E Vernon Hills Illinois 60061 www rustoleum com BRANDS An RPM Company
4. UCT APPLICATION SURFACE PREPARATION Surfaces should be clean dry sound and free of dust dirt excessive chalky material grime grease oil wax mildew wallpaper adhesive or any contamination that may interfere with adhesion If unsure of cleanliness always wash surface with an appropriate ammoniated cleaning solution or solvent do not use TSP as a cleaner Remove any peeling and or unsound coatings Sand any remaining paint film edges smooth with the surface Lightly sand exposed exterior wood with 80 to 100 grit sandpaper to remove loose or weathered wood fibers and mill glaze When priming over stained areas first attempt to remove as much of the stain as possible by washing sanding scraping etc Bare wood that has been exposed for more than 4 weeks should be lightly sanded or abraded to remove weathered wood fibers Remove exterior mold amp mildew with Zinsser Jomax Mildew Killer and House Cleaner Remove interior mold and before painting with a solution of one cup household bleach per gallon of water or a quality mildew cleaner Rinse well and allow surface to dry completely before priming Countersink exposed nail heads spot prime and fill all nail holes and gouges with Zinsser Ready Patch spackling compound Wire brush rusty areas Spot prime knots and sap streaks with B I N Primer Sealer before whole surface priming with Cover Stain High Base WARNING If you scrape sand or remove old paint you may release le
5. ad dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH Approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 800 424 LEAD or log on to www epa gov lead Form CS2243 Rev 100313 TECHNICAL DATA BULLS EYE 1 2 3 WATER BASED PRIMER PRODUCT APPLICATION cont MIXING Brush Goods Mix thoroughly to ensure any settled pigment is re dispersed DO NOT THIN APPLICATION Apply only when air material and surface temperatures are between 50 90 F 10 32 C and the surface temperature is at least 5 F 3 C above the dew point The relative humidity should not be greater than 85 Brush Goods Mix thoroughly to ensure any settled pigment is re dispersed before using In most cases only one coat is necessary to prime most surfaces If excessive absorption occurs over very porous substrates a second coat may be necessary Spot priming is recommended only under high hiding topcoat paints For best results prime entire surface before painting Apply with a natural or synthetic bristle brush roller pad or sprayer Follow manufacturer s instructions when using spray equipment Airless spraying use a 017 tip at 2000 to 2500 psi Aerosol Sha
6. ke can vigorously for one minute after the mixing ball begins to rattle If mixing ball fails to rattle DO NOT STRIKE CAN Contact Rust Oleum Shake often during use Hold can upright 10 16 from surface and spray in a steady back and forth motion slightly overlapping each stroke Keep the can the same distance from the surface Keep the can in motion while spraying Apply two or more light coats a few minutes apart to avoid drips and runs Do not use near open flame CLEAN UP Brush Goods Clean up spills and paint drips with warm water and liquid detergent Wipe up splatters before they dry Follow manufacturer s directions to clean spray equipment Dispose of unused or unwanted product in accordance with local laws regulating solvent based coatings Aerosol Wipe off tip before storing Clean up wet paint with xylene or mineral spirits Properly discard empty container Do not burn or place in home trash compactor If the valve clogs twist and pull off spray tip and rinse ina solvent such as mineral spirits Do not insert any object into can valve opening 2 Form CS2243 Rev 100313 TECHNICAL DATA BULLS EYE 1 2 3 WATER BASED PRIMER PHYSICAL PROPERTIES Aerosol Brush Goods Resin Type Styrene Acrylate Copolymer Styrenated Acrylic Pigment Type Titanium Dioxide Titanium Dioxide MIR 1 2 Max NA Fill Weight 13 ounces NA Solvents Acetone
Download Pdf Manuals
Related Search