Wolman 14706 Use and Care Manual
Contents
1. Causes eye and skin irritation Prevent contact with eyes and skin During preparation and application wear rubber or PVC gloves and safety goggles Wash thoroughly after handling May cause respiratory and throat irritation Do not breathe spray mist If applying with a sprayer wear a properly fitted NIOSH approved respirator Use only with adequate ventilation KEEP OUT OF REACH OF CHILDREN Form JPB 189 2 Rev 082213 TECHNICAL DATA DECKSTRIP ASR ACRYLIC STAIN REMOVER PHYSICAL PROPERTIES Active Ingredient Sodium Hydroxide Weight Per gallon 8 9 9 3 Ibs 1 06 1 11 kg Depending on coating type number of layers surface porosity and method of application Theoretical Coverage 1 gallon covers approximately 150 sq ft Application Parameters Minimum 50 10 C Dry Time Allow wood to dry thoroughly before applying a water based stain or finish Allow a minimum of 24 hours before applying oil based stain or finish Biodegradable Biodegrades into inert chemicals Flash Point gt 200 F The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replac2. ement of defective materials All technical information is subject to change without notice 3 Rust Oleum Corporation Form JPB 19 11 Hawthorn Parkway Phone 877 385 8155 Rev 082213 Vernon Hills Illinois 60061 www rustoleum com An RPM Company
3. po TECHNICAL DATA W OL07 DECKSTRIP ASR ACRYLIC STAIN REMOVER DESCRIPTION AND USES PRODUCT APPLICATION CONT Wolman DeckStrip ASR Acrylic Stain Remover is a ready to use premium quality exterior wood stripper for all types of acrylic deck and siding stains In just 15 minutes DeckStrip ASR will cut through and remove relatively new or weathered acrylic latex solid and semi solid stains including those labeled 100 acrylic With the aid of a highly concentrated formula special wetting agents and a thickener for vertical surfaces tough to remove acrylics are quickly dissolved and easily rinsed away with a pressure washer no scraping or sanding required Once stripped wood is restored to its bright clean natural look Using DeckStrip ASR before re application of a protective finish or stain ensures its proper adhesion penetration and optimum performance FEATURES Safe to use no methylene chloride or caustics Spray on pressure wash away No scraping or sanding Clings to vertical surfaces for one application stripping 100 Biodegradable safe for grass plants and shrubs PRODUCT SKU 14706 1 Gallon RECOMMENDED USES FOR EXTERIOR USE ONLY Use DeckSirip ASR to strip and restore outdoor wood decks fences siding shakes and shingles boat docks amp boardwalks outdoor furniture amp d cor gazebos amp arbors play sets and more WOOD TYPES Use on all wood types including pressure trea
4. ted lumber Cedar Redwood exotic hardwoods Mahogany lp Teak etc and North American hardwoods Note To strip traditional oil or solvent based deck stains semi transparent toners tinted wood protectors or sealers etc select Wolman DeckSirip Stain amp Finish Remover and use according to label directions PRODUCT APPLICATION Before You Start Make sure entire wood surface is dry and free of dust dirt and debris If the surface is hot to the touch or in direct sunlight dampen with fresh water to cool Apply when outside temperatures are above 40 F Pre rinse grass plants and shrubs surrounding the wood structure to be stripped then cover foliage to protect it from exposure to the product Mask off siding and cover all wood surfaces not intended to be stripped Cover any exposed aluminum surfaces siding and flashing to prevent corrosion Protect adjacent concrete surfaces from rinse water Sweep away surface dirt and debris Remove any standing water before beginning application Weather Conditions For best results apply when outside temperature is above 50 F 10 C and when 24 hours of precipitation free weather is expected Surface to be stripped should be out of direct sunlight to avoid premature evaporation of the product A synthetic bristle brush or mop pump sprayer or airless sprayer with no aluminum parts is recommended When working on vertical surfaces start at the bottom and work to the top of the str
5. ucture Safe Handling directions must be followed to avoid exposure to over spray See Handling and Storage section CAUTION Bare wood and or coated surfaces can become slippery when wet Use caution when walking on wet surfaces Prepare to Use Moderately shake container then pour into sprayer tank If using a brush or mop pour product into a 2 1 2 gallon plastic bucket Do not mix with any other products Apply Working on 20 sq ft at a time to maintain optimum surface wetness apply product and let sit for 15 minutes If stripper dries prematurely keep it wet with additional product as needed Rinse Pressure Wash Using a 40 tip and 1 500 2 500 PSI for pressure treated wood and hardwood 500 1 000 PSI for Cedar and Redwood pressure wash the surface to rinse away dissolved coating Move lengthwise with boards to avoid cut marks across grain Repeat steps until entire surface has been stripped When finished rinse surrounding grass and plants thoroughly Rinse Brush and Hose If pressure washing cannot be employed vigorously scrub surface with a Wolman WOODWORX Deck Brush or other stiff synthetic short bristle broom or brush for several minutes using moderate pressure After brushing rinse thoroughly with a garden hose using the highest pressure nozzle setting available On a vertical surface continually rinse stripped areas to avoid streaking Rinse any wood fibers off surrounding surfaces immediately When dr
6. y surface should appear clean bright and free of previous coating Repeat steps until entire surface has been stripped When finished rinse surrounding grass and plants thoroughly Note After stripping Cedar Redwood or exotic hardwoods black tannin stains may rise to the surface and give wood an overall darkened appearance If this occurs treat affected areas with Wolman Deck amp Fence Brightener liquid concentrate to restore the natural wood color DeckStrip ASR is not designed to remove tannin bleed stains Form JPB 19 Rev 082213 TECHNICAL DATA DECKSTRIP ASR ACRYLIC STAIN REMOVER HANDLING AND STORAGE Clean Up Clean tools and equipment immediately after use with soap and water Use water or vinegar soaked rag to wipe off any drips or spills on unintended surfaces immediately Safe Handling During preparation and application wear rubber or plastic coated gloves and safety goggles If applying with a sprayer wear a NIOSH approved full face respirator with an organic vapor cartridge and N 95 pre filter Care should be taken to cover any exposed aluminum surfaces to prevent discoloration as this product is corrosive to metal DO NOT MIX WITH ANY OTHER PRODUCTS especially those containing chlorine or bleach sodium hypochlorite Rinse grass and plants with water after exposure Precautions DANGER MAY BE FATAL IF SWALLOWED CAUSES SEVERE BURNS CONTAINS SODIUM HYDROXIDE May be harmful if swallowed
Download Pdf Manuals
Related Search