ZyXEL ZyAIR B-400 User's Manual
Contents
1. 15 ZyAIR B 400 Quick Installation Guide FAQ and Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of the B 400 Please refer to the following descriptions and for further assistance please contact the dealer Q My PC can t locate the Wireless Ethernet adapter How do solve the problem A Please follow the procedures below Check if the Ethernet cable is well connected Check if the IP addresses of the PC and B 400 Wireless Ethernet adapter both are on the same IP network If not the Wireless Navigator can be used to set up the adapter s IP address or the PC s IP address can be changed directly Q The B 400 adapter cannot communicate with the Wireless Access Point How do solve the problem A Please follow the procedures below Check if the Wireless Navigator utility is available to access the B 400 first If not please go through the procedure of Q1 Check if the adapter is set to Infrastructure correctly Check if the SSID of your adapter is the same as AP s If not please set it to the same SSID as the access point Check if WEP is enabled either in the B 400 adapter or at the access point If yes please make sure that the adapter and the Wireless Access Point both have the same WEP settings 16 ZyAIR B 400 Quick Installation Guide since the keys must match m Finally please check if radio interference i2. ZyAIR B 400 11Mbps Wireless LAN Ethernet Adapter Quick Installation Guide ZyAIR B 400 Quick Installation Guide FCC Warning The ZyAIR B 400 has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment FCC Radiation Exposure Statement The ZyAIR B 400 complies with FCC radiation exposure limi
3. allShield Wizard Customer Information Please enter your information Please enter your name and the name of the company for whom you work User Name N athan Company Name Company InstallShield lt Back Cancel 10 ZyAIR B 400 Quick Installation Guide Step 4 The screen will show the default destination chosen by the utility To install the Wireless Navigator in another location click the Browse button and select an alternate destination Click the Next button when ready to continue The setup program will then begin to install the programs into the destination folder InstallShield Wizard Choose Destination Location Select folder where Setup will install files Setup will install Wireless Navigator in the following folder To install to this folder click Next To install to a different folder click Browse and select another folder Destination Folder C Program Files Wireless Navigator Browse InstallShield i Cancel Step 5 The screen will show the Program Folder that the utility will use Users may type a name to create a new program folder or select one from the existing folder list Then click the Next button to continue 11 ZyAIR B 400 Quick Installation Guide InstallShield Wizard Select Program Folder Please select a program folder Setup will add program icons to the Program Folder listed below You may type a n
4. and Rx lines are reversed Use this setting when using a straight cable connected to a PC or other Ethernet device It is also the factory default setting Il Straight Straight the RJ 45 port Tx and Rx lines are normal Use this setting when using a straight cable connected to an Ethernet device such as an Ethernet hub switch ZyAIR B 400 Quick Installation Guide LAN Connection Use a standard straight UTP Ethernet cable RJ 45 connector to attach the PC hub switch or broadband router modem to this port Power Input Only use the power adapter supplied with the adapter LED Indications co cow sae omen Green FON The LAN port is linked The LAN port is not linked with any Ethernet device inki The LAN port is sending or receiving data Green The B 400 is linked with a wireless LAN device No data is forwarding between the wireless LAN and wired LAN ports Blinking Sending or receiving wireless data ZyAIR B 400 Quick Installation Guide Hardware Installation The following illustration is an example showing how to install the B 400 adapter with a PC Be sure to use the supplied power adapter Desk top Pit Ethemet Interface Wa Power adapts Ethernet cable Ethemet Adapter The B 400 may also be connected to other Ethernet ready devices such as print servers ZyAIR B 400 Quick Installation Guide Wireless Navigator Installation The Wireless Navigator Utility is provided to al
5. ew folder name or select one from the existing folders list Click Next to continue Program Folders Wireless Navigato Existing Folders Microsoft Office NetIQ Qcheck Norton Antivirus Corporate Edition PRISM Test Utilities USB Wireless Network Adapter WinRAR Wireless Network PC Card InstallShield lt Back Cancel Step 6 The Wireless Navigator has been installed now and then click the Finish button to to complete the installation InstallShield Wizard Complete Setup has finished installing Wireless Navigator on your computer i Cancel To remove the Wireless Navigator click the Start button and select Programs Wireless Navigator and Uninstall and then follow the instructions on the screen ZyAIR B 400 Quick Installation Guide Startup and Login to the B 400 Follow the procedures below to startup the Wireless Navigator and locate the B 400 Ethernet adapter 1 Refer to Wireless Navigator Installation to install the Wireless Navigator 2 Click Start and select Programs Wireless Navigator and then Wireless Navigator Or just double click the Wireless Navigator icon on the desktop screen 3 The Wireless Navigator starts up and searches for adapters located on the wired and wireless LAN Tiere Meagan 2 5 Ei Edi Few Amm Help ESS1D Chorraha WEP Maccrese Seanchung for Wireless Eemi Adanta on thes network ZyAIR B 400 Quick Installati
6. low users to easily configure the B 400 adapter using any Windows based PC This section describes procedures for installing the Wireless Navigator Utility onto the PC Please make sure that the PC already has the TCP IP protocol installed If not please consult the Windows help file for assistance with setting up TCP IP on the PC If the B 400 adapter is used with a non PC Ethernet device such as a print server or game console users can still install the Wireless Navigator in any PC located in the same IP subnet with the B 400 The utility can locate the B 400 via both wired and wireless Ethernet connections for remote management Step 1 Insert the installation CD ROM into the CD ROM drive Run the SETUP EXE program on the CD ROM The following window will be shown automatically InstallShield Wizard Wireless Navigator Setup is preparing the InstallShieldR Wizard which will guide you through the rest of the setup process Please wait ZyAIR B 400 Quick Installation Guide Step 2 After the InstallShield Wizard preparation is finished the following window will be shown Click the Next button to continue InstallShield Wizard x Welcome to the InstallShield Wizard for Wireless Navigator The InstallShieldR Wizard will install Wireless Navigator on your computer To continue click Next Step 3 Type in the User Name and Company Name and click the Next button to continue Inst
7. on Guide 4 The utility will show the B 400 adapter connected to the PC Please change the adapter IP address and check that the computer IP address and the adapter IP address are on the same subnet From Admin set IP address Lipase essi Chan Ho Moe Addes PS O02 Tb Adate 169254100100 jsheerb2000 7 Ditatled 00 90 CC 44 DC GE If the B 400 adapter is not shown in the list please make sure all the cables are well connected 14 ZyAIR B 400 Quick Installation Guide 5 Double click on the adapter to access its built in web server The below screen will show Click the OK button The default user name is admin and the default password is 1234 zixl Ss Please type your user name and password Site 192168111 Resim 802 11b Bridge User Nome sdmin Password t T Save this password in your password list Conca 6 The below screen will then appear The B 400 s built in web server has been successfully entered and the user can configure the B 400 information about the Adapter MOTE Tou mury h ra fo re load this page Io see the Current stings SSID otis Charnunel T ESSO Cre ie SS Set ae Transmission Rate pA Link Quality E MAC address Dotter ie awe IP Address 66 Firmware Revision BRO Fesus of the most recent scan Wima GRAD EAT rice 1 100 inira 7 For details of how to configure the B 400 adapter please refer to the User s Manual supplied in the CD
8. s causing a problem see if connection is possible when close to the Wireless Access Point The connection range can be as short as 100 feet in a poor environment Q The Wireless connection speed is very slow How can improve it A The wireless system will connect at the highest possible speed depending on the distance and environment conditions To obtain the highest possible connection speed try to adjust the location of the B 400 and its antenna s direction If interference is the problem changing to another channel 1 6 or 11 may improve the signal Q How do I access the ZyAIR B 400 if am using a MAC or Linux PC or if do not have the Wireless Navigator A The default IP of the ZyAIR B 400 is 192 168 1 11 The web configurator can be accessed through the web browser directly Note The host s IP must be first configured to the same subnet as the ZyAIR B 400
9. the availability and reliability of wireless connections Roaming Provides seamless roaming within the IEEE802 11b wireless LAN infrastructure Configuration amp Management gt Easy to Setup With the Windows based Wireless Navigator Utility users can easily setup the IP address of the adapter and upgrade the firmware gt Easy to Manage The adapter can be easily configured using any WEB browser from anywhere on the wired or wireless LAN Security gt Configuring Protection Provides password protection to prevent unauthorized users from changing the configuration gt Wireless LAN Security Provides 64 bit amp 128 bit Wired Equivalent Privacy WEP encryption to protect the wireless data transmissions ZyAIR B 400 Quick Installation Guide Package Contents v v v v One ZyAIR B 400 11Mbps Wireless LAN Ethernet adapter One installation CD ROM Wireless Navigator Utility amp User s Manual Included One power adapter One quick installation guide If any of the above items are damaged or missing please contact your dealer immediately ZyAIR B 400 Quick Installation Guide Physical Details Rear Panel INIT Button LAN Cable Selection Switch LAN Connection Power Input INIT Button INIT means Initialize Pressing the button will reboot the device and restore the settings to the factory default settings LAN Cable Selection Switch X Crossover the RJ 45 port Tx
10. ts set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This equipment must not be co located or operating in conjunction with any other antenna or transmitter CE Marking Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures ZyAIR B 400 Quick Installation Guide Table of Contents ZYAIR B 400 FEATURES 4 PACKAGE CONTENT S cco 5 PHYSICAL 6 HARDWARE INSTALLATION ccccccccessssees 8 WIRELESS NAVIGATOR INSTALLATION 9 STARTUP AND LOGIN 13 FAQ AND TROUBLESHOOTING cccceeeees 16 ZyAIR B 400 Quick Installation Guide ZyAIR B 400 Features LAN Features gt DHCP Support Enable the adapter to act as a DHCP client to receive an IP address from a DHCP Server in the wired Ethernet LAN Built in 10BaseT LAN Port Designed to connect the adapter with any Ethernet ready device such as a desktop PC print server and network printer scanner Wireless Features gt Standard Compliant The adapter complies with the IEEE802 11b standard and it is interoperable with IEEE802 11b Compliant Equipment High speed Wireless Connection Supports up to 11Mbps wireless data rate Data Rate Auto Fall Back Provides 11 5 5 2 and 1Mbps wireless data rates Shifts dynamically to guarantee
Download Pdf Manuals
Related Search