Home

ZyXEL zyxel Prestige100 User's Manual

1. Menu Title Description 1 General Setup Setup general information 2 ISDN Setup Setup ISDN configuration 3 Ethernet Setup Setup Ethernet configuration 4 Internet Access Setup A quick and easy way to setup Internet connection 11 Remote Node Setup Setup Remote Node for LAN to LAN connection including Internet connection Prestige has four Remote Nodes 12 Static Routing Setup Setup static route for protocol There are four static routes for IP protocol 13 Default Dial in Setup Setup default dial in parameters such that your Prestige can be a dial in server for the 28 Installation Menu Title Description Remote Node and Remote Dial in User 14 Dial in User Setup Setup Remote Dial in User Prestige has eight Remote Dial in Users 21 Filter Set Configuration Setup filters to be used in Menu 3 and Menu 11 to provide security call control etc 23 System Security Setup security related parameters 24 System Maintenance Provide system status diagnostics firmware upload etc 99 Exit To exit from SMT and return to the blank screen General Setup This menu contains administrative and system related information Enter 1 in the main menu to go to Menu 1 General Setup Menu 1 General Setup System Name P1680 Location Alpha Lab Contact Person s Name CC Route IP Yes Press ENTER to Confirm
2. Figure 3 7 Menu 2 ISDN Setup for North America 1 Switch Type Please verify the switch type information with your telephone company For North America select the type of switch used by your telephone company If your switch type is not currently shown press the space bar to change to the next switch repeat until you see the correct switch type The Prestige will not be able to place or to receive calls if the wrong switch type is specified If you are not sure contact your telephone company to confirm the exact switch type B Channel Usage In general this will be Switch Switch If you are only using one B channel e g your Prestige is sharing the ISDN BRI line with another device on the S T bus then select Switch Unused The default is Switch Switch Telephone Number s Enter the telephone number s assigned to your ISDN line by your telephone company Some switch types only have one telephone number For North America these phone numbers should be in a standard seven digit format for example 5551212 Note that the Prestige only accepts digits please do not include and spaces in this field This field should be no longer than 19 digits Analog Call This tells the Prestige how to route an incoming analog call Set to Phonel if you wish to route the incoming analog call for this telephone number to the PHONE port 1 a k a POTS port in North America and A B Adapter i
3. 9 Analog Call Routing All analog calls will be routed to the A B Adapter 1 if the setting is A B Adapter 1 Or they will be routed to the A B Adapter 2 if the setting is A B Adapter 2 Or they will not be answered if the setting is Ignore 10 Global Analog Call All global analog calls will be answered and routed to the A B Adapter 1 or A B Adapter 2 the setting in the filed of Analog call routing if the setting is Accept Or they will not be answered if the setting is Ignore When you are finished press ENTER at the message Press ENTER to Confirm to save your selections or press ESC to cancel When you press ENTER the Prestige will use the information that you entered to initialize the ISDN link to the telephone company switch It should be noted that whenever the switch type is changed the ISDN initialization will take slightly longer In addition if you are using the U interface the system will also take slightly longer to initialize At this point the Prestige will ask if you wish to test to check if your ISDN line has been successfully connected to your Prestige If you select Yes The Prestige will perform a loop back test to check the ISDN line If the loop back test fails please note the error message that you receive and take the appropriate troubleshooting action Setup LoopBack Test Dialing to 40092 Sending and Receiving Data Disconnect
4. Configuring the SMT Password Menu 23 1 System Security Change Password Old Password Hew Password 7 Retype to confirm 7 Enter here to CONFIRM or ESC to CANCEL Figure 9 1 Menu 23 1 System Security Change Password System Security 89 The following steps describe a simple setup procedure for configuring the SMT password From the Main Menu select option 23 System Security This will bring you to Menu 23 System Security 1 From this menu you can select option 1 Change Password This will bring you to Menu 23 1 System Security Change Password 2 Type in your previous system password and press ENTER Type in your new system password and press ENTER 4 Re type your new system password for confirmation purposes and press ENTER You will now need to enter in this password when you try to get into the SMT In addition this password will also be used when a network administrator attempts to telnet to the Prestige 90 System Security 70 Telnet Configuration and Capabilities About Telnet Configuration When you first configure your Prestige it must be done via a computer connected to the RS 232 port However once the Prestige has been initially configured you can use telnet to configure the device remotely as shown below TCPAP Network Telnet from any station on Network Prestige with Network IP Address Telnet from any Switched Remote Loc
5. In Menu 11 1 choose a name for your backup ISP account set the Active field to No and enter your outgoing login name password and phone number s The Remote IP Address field should be set to 1 1 1 1 In Menu 11 3 set the remote node s subnet mask to 0 0 0 0 and set RIP to None Save the new configuration Once you have done this if you need to change from your primary ISP to a backup ISP follow the steps below 1 2 3 4 Enter Menu 11 and select your Primary ISP In Menu 11 1 set the Active field to No Enter Menu 11 again and select your backup ISP In Menu 11 1 set the Active field to Yes You will now be able to access the Internet through the backup ISP Remote Node Configuring for Internet Access 47 48 Configuring for Internet Access 5 Remote Node Configuration A Remote Node represents both a remote gateway and the internet behind it across an ISDN connection A Remote Node is required for placing calls to or answering calls from a remote network Note that when you use Menu 4 to configure the Internet the Prestige will automatically add a Remote Node for you Once a Remote Node is configured properly traffic to the remote LAN will trigger the Prestige to make a call automatically i e Dial On Demand Similarly calls from the remote LAN will be answered automatically and security will be checked In this chapter we will discuss the parameters that are protocol independent The protocol d
6. Options for this field are e CHAP PAP Prestige will try CHAP when CHAP is requested by the Remote Node or PAP when PAP is requested by the Remote Node e CHAP use CHAP only e PAP use PAP only 11 Outgoing Pri mary Phone Sec ondary Phone Number Both the Primary Phone number and the Secondary Phone number refer to the number that the Prestige will dial to connect to the Remote Node The Prestige will always call the 52 Remote Node Configuration 12 13 14 15 16 Remote Node using the Primary Phone number first If the Primary Phone number is busy or does not answer the Prestige will call the Secondary Phone number if available Once connected the Prestige will use the BACP Bandwidth Allocation Control Protocol to establish the second B channel if Multilink PPP is enabled and the Remote Node supports MP and BACP Route This fields determines the protocols that the Prestige will route The choices for this field are determined by the features enabled on your Prestige Edit PPP Options To edit the PPP options for this Remote Node move the cursor to this field use the space bar to select Yes and press ENTER This will bring you to Menu 11 2 Remote Node PPP Options For more information on configuring PPP options please see the section Editing PPP Options IP Addr This is a required field if Route is set to IP Enter the IP address of this Remote Node Edit IP To e
7. Entering Information There are two types of fields that you will need to fill in The first requires you to type in the appropriate information The second gives you choices to choose from In the second case press the SPACE BAR to cycle through the available choices Required Fields Some of the fields in the SMT are essential in order to configure the Prestige These fields will initially show a 7 indicating that the information must be filled in before that menu can be saved N A Fields Some of the fields in the SMT will show a N A which refers to Not Available This symbol usually refers to an option that is not available Installation 27 e Saving Your Configuration You can save your configuration by pressing ENTER at the message Press ENTER to confirm or ESC to cancel Saving the data on the screen will take you in most cases to the previous menu The SMT main menu is shown below Copyright c 1994 1996 ZyXEL Communications Corp Prestige 188 Main Menu Getting Started Advanced Management 1 General Setup 21 Filter Set Configuration 2 ISDN Setup 3 Ethernet Setup 23 System Security 4 Internet Access Setup 24 System Maintenance Advanced Applications 11 Remote Node Setup 12 Static Routing Setup 13 Default Dial in Setup 14 Dial in User Setup 99 Exit Enter Menu Selection Number Figure 3 5 SMT Main Menu SMT Summary This section summarizes all major SMT Menus
8. Len 2 Mask ffff Ualue 0802 LA oho ZZZZc lt D zzzZz 3 onon nZ ZzZ l J Enter Filter Rule Number 1 6 to Configure _ Figure 8 3 Menu 21 1 Filter Rules Summary If the filter type is IP TCP IP the following abbreviations will be used e Pr Protocol e SA Source Address e SP Source Port number e DA Destination Address e DP Destination Port number If the filter type is GEN generic the following abbreviations will be used e Off Offset e Len Length For more information on configuring the filter rule parameters please refer to the next section To configure a specific filter rule simply select the number of the filter rule 1 6 you wish to configure and press ENTER This will take you to Menu 21 1 1 TCP IP Filter Rule next section Filter Configuration 81 Configuring a Filter Rule There are four types of filter rules that you can configure Some of the parameters will differ depending on the type of rule When you first enter the filter rule menu you will be presented with Menu 21 1 1 TCP IP Filter Rule If you wish to configure another type of filter rule you need to select the appropriate type by pressing SPACE bar under the Filter Type field and press ENTER This will bring you to the corresponding menu TCP IP Filter Rule This section will show you how to configure a TCP IP filter rule for your Prestige The fields in the menu ar
9. Please note that this login name password pair is only for the Prestige to connect to the ISP s gateway When you use TCP IP applications e g FTP to access the Internet from your workstation you will need a separate login name and password for each server 7 Single User Account Please see the following section for a more detailed discussion on the Single User Account feature The default is No 8 Telco Options Transfer Rate This field which only applies to outgoing calls controls the rate at which the data is transferred between your Prestige and the Internet There are four options for this field e 64K The Prestige will place 64Kbps bits per second digital data calls e 56K For the North America only The Prestige will place 56Kbps digital data calls e DOVBS For the North America only The Prestige will place 56Kbps Data Over Voice Bearer Service DOVBS call Some phone companies in North America charge less if calls are made using DOVBS 9 Press ENTER at the message Press ENTER to Confirm to confirm your selections or press ESC at any time to cancel your selections 10 At this point the SMT will ask if you wish to test the Internet connection If you select Yes the Prestige will call the ISP to test the Internet connection If the test fails please note the error message that you receive and take the appropriate troubleshooting steps Configuring for Internet Access 43
10. DSS1 ISDN Firmware Version Y Prestige_4 85 Init ISDN line lt This may take up to 28 seconds gt Press ENTER to continue Figure 3 3 Power on Messages If you press ENTER the Prestige will display a login screen and ask you to enter the password as shown in below Enter Password Figure 3 4 Login Screen Enter the default password 1234 to get into the Main Menu of System Management Terminal SMT Note that once you are in the SMT and if there is no activity for longer than 5 minutes the Prestige will automatically log you out and will display a blank screen If you see a blank screen press ENTER to bring up the password screen Navigating Through the SMT The SMT System Management Terminal is the interface that you use to configure your Prestige Several operations that you should be familiar with before you attempt to modify the configuration of your Prestige are listed below Moving Forward to Another Menu To move forward to a sub menu below the current one type in the number of the sub menu and press ENTER Moving Backward to a Previous Menu Press the escape Esc key to move back to the previous menu The only exception is the Main Menu where typing 99 is the only method to exit from the SMT Moving the Cursor Within a menu press Enter carriage return to move to the next field You can also use the Up and Down keys to move to the previous and the next field respectively
11. Phone Jack 2 Dial On Demand 2 Bandwidth On Demand 2 Network Management 3 DHCP Support Dynamic Host Configuration Protocol 3 Security 3 Call Control 3 Data Compression 3 Networking Compatibility 3 Applications For Your Prestige 4 Internet Access 4 Internet Single User Account SUA 4 Telecommuting Server 4 What This Manual Covers 4 What This Manual Doesn t Cover 5 Other Resources 5 Packing List 6 Additional Installation Requirements 6 2 Before You Begin 9 Road Map and Flow 9 viii Completing the Worksheet 10 Ordering Your ISDN Line 10 Collecting General Setup Information 11 Collecting ISDN Phone Line Information 12 Collecting Ethernet Setup Information 14 3 Installation 21 A Warning On Connection Cables 21 Connecting Your Computer and Your Prestige 22 Connecting the RS 232 Cable to your Prestige 22 Connecting an ISDN Line to your Prestige 22 Connecting a Telephone Fax to your Prestige 23 Connecting an Ethernet Cable to your Prestige 23 Connecting a Power Adapter to your Prestige 24 Prestige Front Panel 24 Powering On Your Prestige 25 Navigating Through the SMT 27 SMT Summary 28 General Setup 29 ISDN Setup 30 North American ISDN 30 DSS1 amp 1TR6 ISDN 32 TCP IP Ethernet Setup and DHCP 35 4 Configuring for Internet Access 39 IP Addresses and the Internet 40 Internet Access Configuration 41 Single User Account 44 Configuration for Single User Account 46 Configuring Backup ISP Accounts 46 5 Remote Node Confi
12. System Maintenance This will bring you to Menu 24 System Maintenance From this menu select option 4 Diagnostic This will bring you to Figure 15 4 Menu 24 4 System Maintenance Diagnostic Items 4 12 will describes the nine 9 options to test your Prestige and its connections Hang Up B1 Call This tool hangs up the B1 line This will only be useful if the B1 line is currently connected to a Remote Node or a dial in user Hang Up B2 Call This tool hangs up the B2 line This will only be useful if the B2 line is currently connected to a Remote Node or a dial in user Reset ISDN This command will re initialize the ISDN link to the telephone company ISDN Connection Test You can test to see if your ISDN line has been successfully connected to your Prestige by using this option This command will trigger the Prestige to perform a loop back test to check the functionality of the ISDN line If 100 System Maintenance your line is working properly the test will succeed Otherwise note the error message that you receive and consult your network administrator 8 Manual Call This provides a way for the users of the Prestige to place a manual call to a Remote Node This tests the connectivity to that Remote Node When you use this command you will see traces displayed on the screen showing what is happening during the call setup and protocol negotiation Below is an example of a successful connec
13. The total outgoing call timer can be program need to reset itself periodically through the menu 11 and 13 System Maintenance 107 108 System Maintenance 12 Troubleshooting This chapter contains some problems you may run into when using your Prestige After each problem description we have provided some instructions to help you diagnose and solve the problem Problems Starting Up the Prestige None of the LED s are on when you power up the Prestige e Check the power cord and the power supply and make sure it is properly connected to your Prestige If the error persists you may have a hardware problem In this case you should contact technical support Connecting the RS 232 cable cannot access the SMT e Check to see if the Prestige is connected to your computer s serial port e Check to see if the communications program is configured correctly The communications software should be configured as follows e WVT100 terminal emulation e 9600 Baud rate e No parity 8 Data bits 1 Stop bit Troubleshooting 109 Problems With the ISDN Line The ISDN initialization failed This problem occurs when you attempt to save the parameters entered in menu 2 but receive the message Save successful but Failed to initialize ISDN Press ESC to exit 1 Check the error log in menu 24 3 1 you should see a log entry for the ISDN initialization failure in the format ISDN init failed code lt n gt Note the co
14. a descriptive name for this route This is for identification purpose only 2 Active This fields allows you to activate deactivate this static route 3 Destination IP Address This parameter specifies the IP network address of the final destination Routing is always based on network number If you need to specify a route to a single host use a subnet mask of 255 255 255 255 in the subnet TCP IP Configuration 75 mask field to force the network number to be identical to the host ID 4 IP Subnet Mask Enter the subnet mask for this destination Please follow the discussion on IP subnet mask in this chapter 5 Gateway IP Address Enter the IP address of the gateway The gateway is an immediate neighbor of the Prestige that will forward the packet to the destination On the LAN the gateway must be a router on the same segment as the Prestige over ISDN the gateway must be the IP address of one of the Remote Nodes 6 The Metric and the Private parameters have the same meaning as those in the Remote Node Setup Once you have completed filling in the menu press ENTER at the message Press ENTER to Confirm to save your selections or press ESC at any time to cancel your selections 76 TCP IP Configuration 8 Filter Configuration About Filtering The Prestige uses filters to decide whether or not to allow passage of a data packet and or to make a call over the ISDN line There are three types of filters involv
15. is deactivated it has no effect on the 50 Remote Node Configuration operation of the Prestige even though it is still kept in the database and can be activated in the future Deactivated nodes are displayed with a minus sign at the beginning of the name in Menu 11 Call Direction If this parameter is set to Both the Prestige can both place and receive calls to from this Remote Node If set to Incoming the Prestige will not place a call to this Remote Node If set to Outgoing the Prestige will drop any call from this Remote Node Several other fields in this menu depend on this parameter For example in order to enable Call Back the Call Direction must be Both Incoming Rem Node Login Name Enter the login name that this Remote Node will use when it calls into the Prestige The login name in this field combined with the Rem Node Password will be used to authenticate the incoming calls from this node Incoming Rem Node Password Enter the password used when this Remote Node calls into the Prestige Incoming Rem CLID This field is active only if Call Direction is either Both or Incoming Otherwise an N A appears in the field This is the Calling Line ID the telephone number of the calling party of this Remote Node If you enable the CLID Authen field in Menu 13 Default Dial In the Prestige will check this number against the CLID in the incoming call
16. of Bandwidth channel s used on demand BTR 64 MTR 64 1 Off BTR 64 MTR 128 1 On BTR 128 MTR 128 2 Off When bandwidth on demand is enabled a second channel will be brought up if traffic on the initial channel is higher than the high Target Utility number for longer than the specified Add Persist value Similarly the second channel will be dropped if the traffic level falls below the low Target Utility number for longer than the Subtract Persist value The Target Utility specifies the line utilization range at which you want the Prestige to add or subtract bandwidth The range is 30 to 64 kbps kilobits per second The parameters are separated by a For example 30 60 means the add threshold is 60 kbps and subtract threshold is 30 kbps The Prestige will perform bandwidth on demand only if it initiates the call Addition and subtraction are based on the value set in the BOD Calculation field If this field is set to Transmit or Receive then traffic in either direction will be calculated to determine if a link should be added or dropped Transmit will only use outgoing traffic to make this Remote Node Configuration 55 determination and Receive will only use incoming traffic to make this determination If after making the call to bring up a second channel the second channel does not succeed in joining the Multilink Protocol bundle because th
17. office environment the Prestige offers a Single User Internet Account from an ISP Internet Service Provider This allows for unlimited users on the LAN Local Area Network to access the Internet concurrently for the cost of a single user Single User Account address mapping can also be used for LAN to LAN connection Telecommuting Server The Prestige allows Remote Dial in Users to dial in and gain access to your LAN This feature enables users that have workstations with remote access capabilities e g Windows 95 to dial in using an ISDN terminal adapter TA to access the network resources without physically being in the office What This Manual Covers 4 Introduction This manual is divided into five parts 1 Part One Getting Started Chapter 1 3 is structured as a step by step guide to help you connect install and setup your Prestige to operate on your LAN 2 Part Two The Internet Chapter 4 describes how to configure the Prestige to connect to the Internet 3 Part Three Setting Up Advanced Applications Chapter 5 10 describes how to use the Prestige for more advanced applications such as TCP IP 4 Part Four Advanced Management Chapter 11 14 provides information on advanced management features for network managers 5 Part Five System Maintenance Chapter 15 16 describes maintenance features for checking system status and logging errors Regardless of the application it is importan
18. or ESC to Cancel Figure 3 6 Menu 1 General Setup 1 System Name Choose a descriptive name for the Prestige for identification purposes e g p100 This name should be no more than 8 alphanumeric characters Spaces are not allowed but and _ are accepted Location Enter the geographic location up to 31 characters of your Prestige e g Kansas City Installation 29 3 Contact Person s Name Enter the name up to 8 characters of the person in charge of this Prestige e g Peter Housel The Location and the Contact Person fields are optional ISDN Setup 30 Installation Menu 2 is for you to enter information about your ISDN line Different telephone companies deploy different types of switches for ISDN service Depending on the switch for your particular installation you will have a different number of telephone numbers If you are in North America you may also have SPIDs Service Profile Identifier Make sure that you have correct and complete telephone numbers and SPIDs You need to pass the ISDN setup before your system can make an outgoing call or answer an incoming call North American ISDN Menu 2 ISDH Setup Switch Type Northern Tel Custom B Channel Usage Switch Switch ist Phone 5552000 SPID 8555200001 Analog Call Phone 1 2nd Phone 5554000 SPID 0555400001 Analog Call Phone 2 Press ENTER to Confirm or ESC to Cancel Press Space Bar to Toggle
19. sets with six rules in each set Therefore the Prestige allows you to customize up to 72 filter rules 12 x 6 When implementing these filter sets you can link up to four of the filter sets together to screen the data packet Therefore with each filter set having up to six rules you can have a maximum of 24 rules active for a single filtering application 78 Filter Configuration Configuring a Filter Set In order to distinguish between the 12 filter sets each filter set should have a name or some comments You can edit these comments in the following way 1 From the Main Menu select option 21 Filter Set Configuration This will bring you to Menu 21 Filter Set Configuration 2 From this menu you can choose from among the twelve filter sets Select the filter set you wish to configure 1 12 This will bring you to the Edit Comments field Whatever the comments are for that filter set will be displayed in this field You can edit the comments you wish to use to identify that filter set Once you have completed filling in the Edit Comments field press ENTER at the message Press ENTER to Confirm to confirm your selections or press ESC at any time to cancel your selections The new information will now be displayed in the read only section of Menu 21 Filter Set Configuration as shown below Menu 21 Filter Set Configuration Filter Filter Set Comments Set Comments 1 Filter
20. the Internet For more information on IP address translation refer to RFC 1631 The IP Network Address Translator NAT In summary 44 Configuring for Internet Access 1 SUA is an ideal cost effective solution for small offices with less than 20 hosts using a LAN to concurrently access the Internet or other remote TCP IP network 2 SUA can provide one server address to be accessed by Remote Dial in Users thus controlling the incoming packets 3 SUA can provide firewall protection if you do not configure a server IP address All incoming inquiries will be filtered out by the Prestige Therefore servers on your network are protected 4 UDP and TCP datagrams can be routed In addition ICMP echo can also be routed The figure below shows an example of a small office connected to the Internet via a Single User Account using the Prestige Note that if you enable the Single User Account feature your local IP address MUST be selected from the list of IP addresses for private networks as defined by the IANA Single User Account Using the Prestige Assigned IP Address by ISP Prestige ae aS Same Network Addresses Figure 4 3 A Single User Account Using the Prestige Configuring for Internet Access 45 Configuration for Single User Account The steps for configuring your Prestige for Single User Internet Access are identical to conventional Internet Access with the exception that you need to fill in three
21. 0 to 65535 Destination Port Comp In this field you can select what comparison quantifier you wish to enable to compare to the value given in Destination Port There are five options for this field e None e Less e Greater e Equal e Not Equal Source IP Addr In this field enter the source IP Address of the packet you wish to filter The address is usually written in dotted decimal notation such as a b c d where a b c and d are numbers between 0 and 255 Source IP Mask In this field enter in the IP mask that will be used to mask the bits of the IP Address given in Source IP Addr Source Port Enter the source port of the packets that you wish to filter The range of this field is 0 to 65535 Filter Configuration 83 11 Source Port Comp In this field you can select what comparison quantifier you wish to use to compare to the value given in Source Port There are five options for this field e None e Less e Greater e Equal e Not Equal 12 TCP Estab This field is dependent upon the IP Protocol field This field will be inactive N A unless the value in that field is 6 TCP protocol In this field you determine what type of TCP packets to filter There are two options e Yes filter match only established TCP connections e No filter match both initial and established TCP connections 13 More In this field you can determine if you want to pass the packet t
22. 55 172 16 0 0 172 325 259 255 192 168 0 0 192 168 255 255 40 Configuring for Internet Access Fs Note For this reason it is recommended that you choose your network number from the above list You can obtain your IP address from the IANA from an ISP or assigned from a private network If you belong to a small organization and your Internet access is through an ISP the ISP can provide you with the Internet addresses for your local networks On the other hand if you are part of a much larger organization you should consult your network administrator for the appropriate IP addresses Regardless of your particular situation do not create an arbitrary IP address always follow the guidelines above For more information on address assignment please refer to RFC 1597 Adaress Allocation for Private Internets and RFC 1466 Guidelines for Management of IP Address Space Once you have determined the IP address range for your local network you may want to use DHCP Dynamic Host Configuration Protocol to assign addresses to individual hosts on the network as an alternative to manually configuring each host s IP settings See the TCP IP Ethernet Setup and DHCP section on page 35 for more information about DHCP Internet Access Configuration The following steps describe the set up procedure to configure your Prestige for Internet access The information you will need to provide will be indicated in bold type Configuring for I
23. B 61 36 49 68 OG 86 80 CO 44 8 22 08 88 62 2B 20 64 G6 68 S AD D CA 44 87 22 Ai 82 63 BA OS 66 BY S 89 BA OB Source MAC Address LAN Packet Which Triggered Last Call Type Raw Fs FF FF 22 OA 11 HA HA GA AA FF FF FF FF FF FF 4 52 OA GG GO AA HH 40 35 98 84 B9 40 88 88 83 82 78 81 AS AS AS AS AS AS AS AS Figure 11 3 LAN Packet Which Triggered Last Call Terminal Baud Rate Users can set up different baud rates for the RS 232 connection through menu 24 2 Terminal Baud rate The Prestige supports 9600 default 19200 and 38400bps for the RS 232 connection 96 System Maintenance Menu 24 2 System Maintenance Change Terminal Baud Rate Terminal Baud Rate 384688 Press ENTER to Confirm or ESC to Cancel Press Space Bar to Toggle Figure 11 4 Menu 24 2 System Maintenance Change Terminal Baud Rate Log and Trace Log and trace tools allow users of the Prestige to view the error logs and trace records to troubleshoot any errors that may occur The Prestige is also able to generate syslogs to send to other machines 1 To get to the Log and Trace select option 24 System Maintenance This will bring you to Menu 24 System Maintenance 2 From this menu select option 3 Log and Trace This will bring you to Menu 24 3 System Maintenance Log and Trace 3 You will be given two options e View Error Log e Syslog and Accounti
24. IP address and potentially disrupting the whole network If set to No the remote host must use the IP address assigned by the Prestige from the IP pool configured below The default is Yes 10 Dial In IP Address Supplied By IP Pool This field tells the Prestige to provide the remote host with an IP address from the pool This field is required if Dial In IP Address Supplied By Dial in User is set to No You can configure this field even if Dial in User is set to Yes in which case the Prestige will accept the IP address if the remote peer specifies one otherwise an IP address is assigned from the pool The default is No 11 IP Pool IP Start Addr This field is active only if you selected Yes in the Dial In IP Address Supplied By IP Pool field The IP pool contains contiguous IP addresses and this field specifies the first one in the pool 12 IP Count 1 2 In this field enter the number 1 or 2 of the addresses in the IP Pool For example if the starting address is 192 168 135 5 and the count is 2 then the pool will have 192 68 135 5 and 192 68 135 6 13 Session Options Input Filter Sets and Session Options Output Filter Sets In these fields you need to select the filter set s to filter the incoming and outgoing traffic between your Prestige and the Remote Dial in User Please keep in mind that these filter set s will only apply to all Remote Dial in Users but not the Remote Nodes You
25. If they do not match and the CLID Authen is Required then the Prestige will reject the call Incoming Call Back This field will be valid only if Call Direction is Both Otherwise an N A appears in the field This field determines whether or not you wish the Prestige to call back after receiving a call from this Remote Node If this option is enabled the Prestige will disconnect the initial call Remote Node Configuration 51 from this node and call it back at the Outgoing Primary Phone Number see below 8 Outgoing My Login Name This is a required field if Call Direction is either Both or Out Enter the login name for the Prestige when it calls this Remote Node 9 Outgoing My Password This is a required field if Call Direction is either Both or Out Enter the password for the Prestige when it calls this Remote Node 10 Outgoing Authen This field sets the authentication protocol used for outgoing calls The Prestige supports two authentication protocols PAP Password Authentication Protocol and CHAP Challenge Handshake Authentication Protocol e PAP sends the user name and password in plain text e CHAP scrambles the password before it is sent over the wire Generally speaking CHAP is more secure than PAP however PAP is readily available on more platforms The recommendation is to use CHAP whenever possible Turning off the authentication is STRONGLY discouraged
26. Node or ISP 111 Problems Connecting to a Remote User 112 13 ISDN Switch Types 113 Provisioning For U S Switches 113 Provisioning For the AT amp T 5ESS Switches 114 Provisioning For the Northern Telecom Switch 115 14 Index 116 xi xii 1 Introduction Congratulations on your purchase of a ZyXEL Prestige 100 Remote Access Router In a modem sized box the Prestige offers inexpensive yet complete telecommunications and internetworking solutions for your home or branch office The Prestige is ideal for everything from surfing the Internet to receiving calls from Remote Dial in Users to making LAN to LAN connections to Remote Nodes Distinguishing features of the Prestige 100 include Remote Dial in User support an Internet Single User Account Network Address Translation POTS line support Plain Old Telephone Service also called A B Adapter in Europe extensive Network Management and the latest security features Features The Prestige 100 is packed with a number of features that give it the flexibility to provide a complete networking solution for almost any user Ease of Installation The Prestige is a self contained unit that is quick and easy to install Physically it resembles an external modem except for the fact that it is a router and uses an Ethernet cable to connect to the host network ISDN Basic Rate Interface BRI Using either a standard S T Interface or a U Interface The Prestige 100 uses the S T interfa
27. Prestige 100 User s Manual Version 3 0 ZyXEL ACCESSING INTERNET amp INTRANET ZyXEL Limited Warranty ZyXEL warrants to the original end user purchaser that this product is free from any defects in materials or workmanship for a period of up to two 2 years from the date of purchase During the watranty period and upon proof of purchase should the product have indications of failure due to faulty workmanship and or materials ZyXEL will at its discretion repair or replace the defective products or components without charge for either parts or labor and to whatever extent it shall deem necessary to restore the product or components to proper operating condition Any replacement will consist of a new or re manufactured functionally equivalent product of equal value and will be solely at the discretion of ZyXEL This warranty shall not apply if the product is modified misused tampered with damaged by an act of God or subjected to abnormal working conditions Note Repair or replacement as provided under this warranty is the exclusive remedy of the purchaser This warranty is in lieu of all other warranties express or implied including any implied watranty of merchantability or fitness for a particular use or purpose ZyXEL shall in no event be held liable for indirect or consequential damages of any kind or character to the purchaser To obtain the services of this warranty please contact ZyXEL s Service Center re
28. Set 1 2 Filter Set 2 8 3 9 4 18 5 11 6 12 Enter Filter Set Humber to Configure Edit Comments Press ENTER to Confirm or ESC to Cancel Figure 8 2 Menu 21 Filter Set Configuration Once you press ENTER you will be taken to Menu 21 1 Filter Rules Summary as seen below The information displayed in this Filter Configuration 79 menu is read only From here you can examine the parameters of each rule that you have configured for that set The following is a brief description of the abbreviations used in this menu e Refers to the filter rule number 1 6 e A Refers to Active Y means the filter rule is active and N means the filter rule is inactive e Type Refers to the type of filter rule This can display GEN for generic or IP for TCP IP e Filter Rules The filter rule parameters will be displayed here see below e M Refers to More Y means there are more rules to check N means there aren t e m Refers to Action Matched F means to forward the packet D means to drop the packet and N means check the next rule e n Refers to Action Not Matched F means to forward the packet D means to drop the packet and N means check the next rule 80 Filter Configuration Menu 21 1 Filter Rules Summary T m Filter Rules m P Pr 1 S5A 204 2147 203 2 SP 520 D A 192 68 135 1 en OFF 4
29. Single User Account Typically if there are multiple users on the LAN wanting to concurrently access the Internet they will have to subscribe to multiple IP addresses or a Class C subnetwork from the ISP In either case these two approaches will cost more than a single user account The Single User Account SUA feature allows customers to have the same benefits as having a Class C address but still only pay for one IP address thus saving significantly on subscription fees Check with your ISP before you enable this feature This feature may also be used to connect to TCP IP remote nodes other than Internet Service Providers For example this feature can be used to simplify the allocation of IP addresses when connecting branch offices to the corporate network The IP address for the Single User Account can be either fixed or dynamically assigned by the ISP or other remote node In addition you can also configure a server e g a Web server on your local network and make it accessible by outside users If you do not set a server IP address SUA offers the additional benefit of firewall protection This is because if no server is defined all incoming inquiries will be filtered out by the Prestige even if you do have a server on your network This can prevent intruders from probing your system The Prestige accomplishes this address sharing by translating the internal LAN IP addresses to a single address that is globally unique on
30. Status select option 24 System Maintenance This will bring you to Menu 24 System Maintenance 2 From this menu select option 1 System Status There are four 4 possible commands in Menu 24 1 System Maintenance Status Entering 1 will disconnect the current B1 channel call 2 will disconnect the current B2 channel call 3 will reset the counters and ESC will exit this screen 4 Items 5 26 describes the fields present in Menu 24 1 System Maintenance Status It should be noted that these fields are READ ONLY and are meant to be used for diagnostic purposes 5 ISDN shows statistics for B1 and B2 channels respectively These are the information displayed for each channel 6 Link shows the Remote Node the channel is currently connected to or the status of the channel Idle Calling or Answering 7 Type the current connecting speed 56K or 64K 8 TXPkt the number of transmitted packets on this channel 94 System Maintenance 10 11 12 13 14 15 16 17 18 19 20 21 22 23 RXPkt the number of received packets on this channel Error the number of error packets on this channel CLU Current Line Utilization percentage of current bandwidth used on this channel ALU Average Line Utilization average CLU for this channel Up Time time this channel has been connected to the current Remote Node Total Outgoing call Ti
31. U S the Prestige both the U and S T interface has been approved by Bellcore and has the IOC ISDN Ordering Code S Capability EZ ISDN 1 Please provide this information to your telephone company when you order your ISDN line If your telephone company is not familiar with this IOC then ask them what kind of switch you will be connected to and use the information under each switch type to order your ISDN line ISDN Switch Types 113 Provisioning For the AT amp T 5ESS Switches The AT amp T 5ESS switch type supports three types of ISDN service These are National ISDN 1 NI 1 Multipoint and Point to Point For AT amp T 5ESS National ISDN 1 Provisioning Feature Setting Term Type A Circuit Switched Voice CSV 1 CSV Additional Call Offering ACO Unrestricted CSV limit 2 CSV Notification Busy NB limit 1 Circuit Switched Data CSD 1 CSD Additional Call Offering ACO Unrestricted CSD limit 2 CSD Notification Busy NB limit 1 MTERM 2 For AT amp T SESS Multipoint Provisioning Feature Setting Term Type D Call Appearances CA 1 CA Quantity 1 Circuit Switched Voice CSV 1 CSV Flexible Call Offering FCO Unrestricted CSV limit 2 CSV Notification Busy NB limit 1 Circuit Switched Data CSD 1 CSD Flexible Call Offering FCO Unrestricted CSD limit 2 CSD Notification Busy NB limit 1 MTERM 2 For AT amp T 5ESS Point to Point Provis
32. __ Phonel ___ Phone2 ___DOVBS e 1st SPID Number e 2nd Telephone Number e Analog Call check one ___Phonel ___ Phone2 ___DOVBS e 2nd SPID Number DSS1 ISDN e ISDN Data Number amp Subaddress e A B Adapter 1 Number amp Subaddress e A B Adapter 2 Number amp Subaddress Before You Begin 17 e Outside Line Prefix Number e PABX Number S T Bus Number e Incoming Number Matching MSN CDSA ___ Don t Care e Analog Call Routing __A B 1 __A B 2 Ignore e Global Analog Call ___ Accept Ignore 1TR6 ISDN e ISDN Data Number e A B Adapter 1 Number e A B Adapter 2 Number 18 Before You Begin e Outside Line Prefix Number e PABX Number S T Bus Number e Incoming Number Matching EAZ ___ Don t Care e Analog Call Routing __A B 1 __A B 2 ___ Ignore Ethernet Setup Information e Ethernet Interface check one AUI UTP e IP Address e IP Subnet Mask Before You Begin 19 20 Before You Begin 3 Installation This chapter outlines how to connect your Prestige to the LAN and ISDN line A diagram of the rear panel of the Prestige is shown below Refer to this diagram to identify all of the ports on your device when you attempt to make the various connections Rear Panel Power Outlet Telephone Fax Les Power CAD 2S Switch fo am e e Telephone Fax Ethernet Eth
33. aller ID in the ISDN call setup message to match against the CLID in the database Dial In Configuration 67 However CLID may not be available due to your switch configuration Besides authentication another application of CLID is to combine it with call back For instance your company pays for the connection charges for telecommuting employees and you are using the Prestige as the dial in server You can turn on both the CLID authentication and call back options for the dial in users By doing so all usage are charged to the company instead of the employees and your accounting department can avoid the hassles of accountability and reimbursement 68 Dial In Configuration 7 TCP IP Configuration This chapter shows you how to configure the Prestige for TCP IP Depending on your particular applications you will need to configure different menus For instance Internet access is the most common application of TCP IP For this application you should configure Menu 4 We will illustrate the configuration for other applications in the following sections IP Subnet Mask A subnet mask is a 32 bit quantity that when logically ANDed with an IP address yields the network number For instance the subnet masks for class A B and C without subnetting are 255 0 0 0 255 255 0 0 and 255 255 255 0 respectively To create more network numbers you shift some bits from the host ID to the network ID For instance to partition a class C netw
34. an link up to 4 filter sets together for further customization e g 1 5 9 12 Please note that spaces and are accepted in this field For more information on customizing your filter sets please see Chapter 8 The default is blank i e no filters defined 20 Session Option Idle Timeout sec This value specifies the number of idle seconds that elapses before the Remote Node is automatically disconnected Idle seconds is the period of time where no data is passed between the Remote Node and your Prestige Administrative packets such as RIP are not counted as data The default is 300 seconds 5 minutes Once you have completed filling in Menu 11 1 Remote Node Profile press ENTER at the message Press ENTER to Confirm to confirm your selections or press ESC at any time to cancel your selections 54 Remote Node Configuration Bandwidth on Demand The Bandwidth on Demand BOD feature allows you to bundle both B channels in one logical connection The second channel is added and subtracted dynamically according to traffic demand The Prestige uses the Bandwidth Allocation Control Protocol BACP and the Multilink Protocol MP in implementing bandwidth on demand The configuration of bandwidth on demand focuses on the Base Transmission Rate BTR and the Max Transmission Rate MTR The relationship between BTR and MTR are shown below BTR amp MTR Setting No of channel s used Max No
35. ansfer rate allowed for this Remote Node This parameter is in kilobits per second There are two options for this field e 64 At most one channel can be used e 128 A maximum of two channels can be used 6 Multiple Link Options Target Utility Enter the two thresholds separated by a for subtracting and adding the second channel The default is 32 48 7 Multiple Link Options Add Persist This parameter specifies the number of seconds there traffic is above the adding threshold before the Prestige will bring up the second channel The default is 5 seconds 8 Multiple Link Options Subtract Persist This parameter specifies the number of seconds where traffic is below the subtraction threshold before the Prestige drops the second channel The default is 5 seconds Once you have completed Menu 11 2 Remote Node PPP Options press ENTER at the message Press ENTER to Confirm to confirm your selections or press ESC to cancel your selections Remote Node Configuration 57 58 Remote Node Configuration 6 _Dial In Configuration You can configure the Prestige to receive calls from Remote Dial in Users e g telecommuters and Remote Nodes There are several differences between Remote Dial in Users and Remote Nodes 1 The Prestige can make calls to or answer calls from the Remote Node But the Prestige will only answer calls from the Remote Dial in User 2 Each Remote Node can have its own set of
36. ation Digital Network Figure 10 1 Telnet Configuration on a TCP IP Network In order to configure your Prestige in this way you need to have assigned an IP Address to your device and have connected it to your network Please see Chapter 3 for more information on assigning an IP Address Once this is configured any station on the Telnet Configuration and Capabilities 91 LAN or remote network that has TCP IP installed can use telnet remote management Telnet Capabilities Single Administrator To prevent confusion and discrepancy on the configuration Prestige will only allow one terminal connection at any time Prestige also gives priority to the RS 232 connection over telnet If you have already connected to the Prestige via telnet you will be logged out if another user is connecting to the Prestige via the RS 232 cable Only after the other administrator has been disconnected will you be able to telnet to the Prestige again System Timeout When you are connected to the Prestige via telnet there is a system timeout of 5 minutes 300 seconds If you are not configuring the device and leave it inactive for this timeout period then the Prestige will automatically disconnect you 92 Telnet Configuration and Capabilities 11 System Maintenance The Prestige provides diagnostic tools that you can use to maintain your device Some of these tools include updates on system status ISDN B channel status log and trac
37. by providing the Prestige with some static routing information As a matter of fact when you configure the Internet Access or a Remote Node a static route is implicitly created by the Prestige An example is given below In the example stations on the 204 5 1 0 24 subnetwork can access the remote stations using the static route The route will have a destination of 204 5 1 64 26 with the gateway address being that of the Remote Node 204 5 1 150 Static Routing Example 204 5 1 0 24 204 5 1 64 26 204 5 1 1 204 5 1 150 204 5 1 151 Figure 7 4 Static Routing Example Please note that in normal circumstances the Prestige will have adequate routing information after you configure the Internet access and Remote Nodes you do not need to configure additional static routes You will need to configure static routes only for unusual cases e g subnetting To create an additional static routes for IP use Menu 12 Static Route Setup as shown below 74 TCP IP Configuration Menu 12 Static Route Setup default test ISP 1 2 3 A Enter Menu Selection Number Figure 7 5 Menu 12 Static Route Setup Main Menu Menu 12 1 Edit IP Static Route Route 1 Route Hame Active Ho Destination IP Address IP Subnet Mask 7 Gateway IP Address 7 Metric Private No Press ENTER to Confirm or ESC to Cancel Figure 7 6 IP Static Route Setup 1 Route Name Enter
38. c Routes if some services reside beyond the immediate remote LAN Remote Node Setup Follow the procedures in Chapter 5 to fill the protocol independent parameters in Menu 11 Remote Node Profile For the protocol dependent parameters follow the instructions below If you are configuring the Prestige to receive an incoming call you also need to set the default dial in parameters in menu 13 see Chapter 6 1 Route Make sure IP is among the protocols in the Route field 2 IP Address Enter the IP address of the gateway at the remote site in this case headquarters If the remote router is using a different IP address than the one entered here the Prestige will drop the call 3 Edit IP Press the space bar to change it to Yes and press Enter to go to the Menu 11 3 Remote Node Network Layer Options menu shown below Menu 11 3 Remote Node Network Layer Options Rem IP Addr 0 0 6 8 Rem Subnet Mask 6 8 0 8 My WAM Addr 1 1 1 1 Single User Account Yes Server IP Addr 6 0 6 8 Metric Private Ho RIP Hone Enter here to CONFIRM or ESC to CANCEL _ Figure 7 2 Menu 11 3 Remote Node Network Layer Options 4 Rem IP Address This will show the IP address you entered for this Remote Node in the previous menu TCP IP Configuration 71 5 Rem IP Subnet Mask Enter the subnet mask for the remote network 6 My WAN Addr Some implementations especially the UNIX derivatives r
39. can choose from 12 different filter sets In addition you can link up to 4 filter sets together for further customization e g 1 5 9 12 Please note that spaces and are accepted in this field For more information on customizing your filter 64 Dial In Configuration sets please see Chapter 8 on Filter Configuration The default is blank i e no filters 14 Session Options Idle Timeout This value is the number of idle seconds that elapses before the dial in user is automatically disconnected Idle Timeout is the period of time when there is no data traffic between the dial in user or Remote Node and the Prestige This field will only be used if the Recv Authen is set to None and the call is not mapped to any Remote Node or Remote Dial in User or the Prestige calls back to the Remote Dial in User Once you have completed filling in Menu 13 Default Dial in Setup press ENTER at the message Press ENTER to Confirm to save your selections or press ESC at any time to cancel your selections Dial In Users Setup The following steps describe the setup procedure for adding a Remote Dial in User From the Main Menu enter 14 to go to 14 Dial in User Setup is shown below Menu 14 Dial in User Setup ra ft 5 B PE 7 POIT MTE ra Enter Menu Selection Number Figure 6 4 Menu 14 Dial in User Setup Dial In Configuration 65 Select one of eight users by n
40. ce and Prestige 100U uses the U interface Introduction 1 2 Introduction the Prestige supports a full range of switch types The switch type depends on the CO Central Office switch your ISDN line is connected to Please see Chapter 13 for more information on North American European and Asian ISDN firmware and switch types supported by the Prestige The two B channels can be used independently for two destinations Or they can be bundled for one connection to support bandwidth on demand Networking Protocol Support The Prestige offers support for TCP IP Standard Phone Jack The Prestige is equipped with two standard phone jacks to connect to telephones FAX machines or modems This allows the ISDN line to be used for voice calls as well as data calls Dial On Demand The Dial On Demand feature allows the Prestige to automatically place a call to a Remote Node whenever there is traffic coming from any workstation on the LAN to that remote site Bandwidth On Demand The Prestige supports bandwidth up to 128Kbps over a single ISDN BRI line It incorporates PPP MP Point to Point Protocol Multilink Protocol to bundle two B channels over a BRI line In addition the Prestige dynamically allocates bandwidth between the two B channels increasing or decreasing speeds as needed to allow for greater efficiency in data transfer It supports BAP Bandwidth Allocation Protocol and BACP Bandwidth Allocation Control Protocol to manag
41. ch Types 115 14 116 Index Index 10Base2 14 24 10Base5 See AUI 10Base T 14 23 1TR6 12 32 34 113 A B Adapter 1 13 31 33 34 Accounting 97 98 AUI 14 24 36 95 111 BACP See Bandwidth Allocation Control Protocol Bandwidth Allocation Control Protocol 3 42 53 55 Bandwidth Allocation Protocol 3 Bandwidth On Demand See BOD BAP See Bandwidth Allocation Protocol Base Transmission Rate 55 Blacklist 104 105 106 BNC See 10Base2 BOD 2 55 56 BTR See Base Transmission Rate Budget Management 63 104 107 Call Detail Record 3 99 Calling Line ID 51 Canadian User Information iv CDR See Call Detail Record Challenge Handshake Authentication Protocol See CHAP CHAP 3 52 62 63 89 CLID 51 62 67 68 99 112 Contacting ZyXEL vi Data Over Voice Bearer Service 31 43 54 DHCP 36 41 DHCP server 37 Dial On Demand 2 49 dial in server 28 29 59 60 DOVBS See Data Over Voice Bearer Service DSS1 12 32 33 34 113 Dynamic Host Configuration Protocol 3 36 FCC Information iii Front panel LED s 24 IANA 40 41 45 Internet 4 Internet Assigned Numbers Authority See IANA IOC 11 See ISDN Ordering Code IP Address 14 37 IP Subnet Mask 14 37 69 72 76 ISDN connecting the line 22 ISDN Ordering Code 11 113 LAN 1 2 4 5 6 9 21 25 28 38 40 44 45 49 59 60 70 71 72 76 92 95 96 111 112 Local Area N
42. cting ZyXEL If you have questions about your ZyXEL product or desire assistance contact ZyXEL Communications Corporation in one of the following ways Phone In North America call between 8 00 AM and 5 00 PM PST at 714 693 0808 Outside North America you can dial 886 3 5783942 EXT 252 between 8 00AM and 5 00PM Taiwan time GMT 8 00 Fax ZyXEL in North America 714 693 8811 or Taiwan 886 3 5782439 E mail e Sales inquiries sales zyxel com in North America sales zyxel hinet net outside North America e Technical support support zyxel com in North America support zyxel hinet net outside North America Product information Visit our site on the World Wide Web http www zyxel com FTP Information such as ZyXEL software and ROM updates for North America can be found at this FTP address ftp zyxel com For European and Asian versions and related files use the address ftp zyxel co at Postal Service You can send written communications to the following address ZyXEL Communications Corporation 6 Innovation Road II Science Based Industrial Park Hsinchu Taiwan 300 R O C or ZyXEL Communications Inc 4920 E La Palma Avenue Anaheim CA92807 U S A vii Contents ZyXEL Limited Warranty ii FCC Part 15 Information iti Information for Canadian Users iv Contacting ZyXEL vi 1 Introduction 1 Features 1 Ease of Installation 1 ISDN Basic Rate Interface BRI 1 Networking Protocol Support 2 Standard
43. d define the filter sets DHCP This field determines what mode of DHCP Dynamic Host Configuration Protocol support the Prestige should use If it is set to None DHCP will not be used If it is set to Server the Prestige will act as a DHCP server capable of automatically assigning IP addresses to Windows 95 Windows NT and other systems that support the DHCP client When DHCP is used the following four items need to be set Do not set this field to Server if there is already a DHCP server on your network Client IP Pool Starting Address DHCP can assign IP addresses to hosts dynamically instead of requiring that each system have a fixed IP address IP addresses are allocated from a block of addresses usually assigned by your Internet provider The Client IP Pool Starting Address gives the first address in the reserved block which is also used as the LAN network address of the Prestige itself This address will also serve as the default gateway for DHCP clients Size of Client IP Pool Gives the size of the block of addresses reserved for DHCP address assignment The Prestige itself uses the first address in the block and the remaining addresses in the pool are assigned to clients Primary DNS Server Secondary DNS Server These two fields are used by DHCP clients such as Windows 95 and Windows NT systems for Domain Name Servers Usually your Internet provider will provide one or more name service hosts IP Address Ent
44. d for informational purposes only Trademarks are properties of their respective owners FCC Part 15 Information This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operations This equipment has been tested and found to comply with the limits for a CLASS B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not iii installed and used in accordance with the instructions may cause harmful interference to radio communications If this equipment does cause harmful interference to radio television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compl
45. de number n 2 Ifthe code is 1 the ISDN link is not up This problem could be either the ISDN line is not properly connected to the Prestige or the ISDN line is not activated Verify that the ISDN line is connected to the Prestige and also to the wall outlet to the telephone company 3 If the code is 2 this indicates an SPID error Verify the SPID s that you have entered in menu 2 If these are correct try to initialize again from menu 24 4 3 4 If the code is 3 this indicates a general failure Verify the SPID s in menu 2 If these are correct you may also need to verify the provisioning information for your switch by contacting your telephone company The ISDN loopback test failed If the ISDN initialization has passed then the loopback test should also pass Verify the phone numbers that have been entered in menu 2 The loopback test will dial the number entered in the 2nd Phone field except for switch types with only one phone number If you need to dial a prefix e g 9 to get an outside line then you have to enter the phone number as 95551212 or 914085551212 If it is an internal line you may only need to enter the last four or five digits according to your internal dialing plan e g 51212 110 Troubleshooting Problems with the LAN Interface Can t PING any station on the LAN 1 Check the LAN LED on the front panel of your Prestige If it is on then the link is up If it is off the
46. ded Twisted Pair UTP cable and RJ 45 connectors that look like a bigger telephone plug with 8 pins Two types of gray Ethernet cables come with the package e Straight through cable white tag Connect your Prestige to a 10Base T hub Installation 23 Warning e Crossover cable red tag Connect your Prestige to your computer directly without a hub If this cable is used to connect ISDN it may damage your Prestige e AUI The AUI port the connector with 15 pins is used to connect the Prestige to a 10Base5 thicknet network If you have a 10Base2 network using BNC connectors and thin coaxial cables you will need a transceiver between the AUI port and the 10Base2 cabling Connecting a Power Adapter to your Prestige Plug the power adapter into the outlet on the rear panel of the Prestige labeled POWER At this point you should have connected the RS 232 cable the ISDN phone line the Ethernet cable and the power supply You can now power on your Prestige Prestige Front Panel 24 Installation Names and descriptions of the Prestige front panel LED s are listed below ISBN LTUERNEET FH I r l Prestige 100 PWR TST INK Bl O BR INK TX BX COL ISDN Reuter IdtEErPraEuadd Figure 3 2 Front Panel PWR This LED power comes on as soon as you connect you Prestige to the power supply and switch it to the T on position TST The TST Test LED should be blinking if the P
47. dit the parameters of the protocols go to this field select Yes and press ENTER This will bring you to Menu 11 3 Remote Node Network Layer Options For more information on filling out this screen please refer to the chapter on TCP IP protocol Telco Options Transfer Rate This field which only applies to outgoing calls controls the rate at which the data is transferred between your Prestige and the Remote Node There are four options for this field e 64K The Prestige will place 64Kbps bits per second digital data calls e 56K For North America only The Prestige will place 56Kbps digital data calls Remote Node Configuration 53 e DOVBS For North America only The Prestige will place 56Kbps Data Over Voice Bearer Service DOVBS call Some phone companies in North America charge less if calls are made with DOVBS option 17 Telco Options Allocated Budget min This field will set a budget outgoing call time for the Remote Node The default for this field is 0 for no budget control 18 Telco Options Period hr This field will set the time interval to reset the above outgoing call budget control 19 Session Option Input Filter Sets Output Filter Sets and Call Filter Sets In these fields select which filter set s you would like to implement to filter the incoming and outgoing traffic between this Remote Node and the Prestige You can choose from 12 different filter sets In addition you c
48. e s No of SPIDs AT amp T 5ESS NI 1 North America AT amp T SESS Point to North America Point AT amp T 5ESS Multipoint North America Northern Telecom NI 1 North America Northern Telecom North America Custom Europe Asia Germany e Switch Type This is the type of switch used by your telephone company Check with your telephone company and choose the appropriate option on the worksheet For North America select your ISDN switch type For DSS1 and 1TR6 verify this field to make sure that you have the proper firmware loaded 12 Before You Begin B Channel Usage Determine which connection is appropriate for your B channel and check the corresponding option on the worksheet If your Prestige is the only device using the ISDN line then configure B Channel Usage to Switch Switch so that your device will use both B channels to communicate If your Prestige is sharing the ISDN line with other devices then configure B Channel to Switch Unused Telephone Number s Record on the worksheet the telephone number s given to you by your ISDN provider Some switch types only have one telephone number These phone numbers should be in a standard digit format for example 5551212 Please note that these fields will only accept digits so and spaces will not be accepted Analog Call Check the appropriate Analog Call option on the worksheet for each telephone number This inf
49. e capabilities and upgrades to the system software This chapter will describe how to use these tools in greater detail System Status System Status is a tool that can be used to monitor your Prestige Specifically it will give you information on the status of your system software version ISDN telephone line number of packets sent and number of packets received Menu 24 System Maintenance System Status Terminal Baud Rate Log and Trace Diagnostic Backup Configuration Restore Configuration Software Update Command Interpreter Mode Call Control ese E ae Enter Menu Selection Number _ Figure 11 1 Menu 24 System Maintenance System Maintenance 93 Menu 24 1 System Maintenance Status ISDH Link Type THPKt REPKt Error CLU ALU Up Time Bi Idle akbps a i o Ax Bx 6 00 00 B2 3086Y 64Kbps 96 72 6 ax Bx 4 01 88 Total Qutcall Time 0 00 00 Ethernet Hame 3064 Link Up RAS S W Version V1 10 8717796 TH Pkt 1287 ISDH FA Version U Prestige_4 86 RK Pkt 2553 Ethernet Address a8 5 18 88 72 Collision Country Code 225 LAN Packet Which Triggered Last Call Type IP 45 68 OG 3C 0 33 GO HA 3B 61 31 A 68 BB HO HA CH 44 87 Gi 88 HA 2D 84 28 64 68 82 HA 2A DE 74 C 44 8 Ai H 61 H2 83 B4 H5 66 G7 BS 89 BA OB Press Command _ COMMANDS 1 Discon Bi 2 Discon B2 3 Reset Counters ESC Exit Figure 11 2 Example of Menu 24 1 System Maintenance Status 1 To get to the System
50. e indicated in bold type Menu 21 1 1 TCP IP Filter Rule Filter 1 1 Filter Type JCP IP Filter Rule Active Yes IP Protocol 1 IP Source Route Ho Destination IP Addr 192 68 135 1 IP Mask 255 255 255 255 Port 520 Fort Comp Hone Source IP Addr 204 247 203 2 IP Mask 255 255 255 255 Port H 520 Port Comp Equal TCP Estab H A More Ho Log Hone Action Matched Forward Action Hot Matched Drop Press ENTER to Confirm or ESC to Cancel Press Space Bar to Toggle Figure 8 4 Menu 21 1 1 TCP IP Filter Rule 1 Active In this field you can make the filter rule active or inactive There are two options e Yes e No 2 IP Protocol Protocol refers to the IP specific number of the protocol The range for this value should be between 0 and 255 For example 6 refers to the TCP protocol 82 Filter Configuration 10 IP Source Route Determine Yes or No whether to check the source route Destination IP Addr In this field enter the destination IP Address of the packet you wish to filter The address is usually written in dotted decimal notation such as a b c d where a b c and d are numbers between 0 and 255 Destination IP Mask In this field enter in the IP mask that will be used to mask the bits of the IP Address given in Destination IP Addr Destination Port Enter the destination port of the packets that you wish to filter The range of this field is
51. e remote device does not recognize the second call as coming from the same device the Prestige will hang up the second channel and continue with the first channel alone Editing PPP Options Menu 11 2 Remote Mode PPP Options Encapsulation Standard PPP Compression Yes Multiple Link Options B alculation Transmit or Receive Base Trans RatelKbps 64 Max Trans Rate Kbps 128 Target Utility Kbps 32 48 dd Persist sec 5 Subtract Persist sec 5 Enter here to CONFIRM or ESC to CANCEL Figure 5 3 Remote Node PPP Options 1 Encapsulation Select CCP Compression Control Protocol for the PPP or MP link There are two options in this field e Standard PPP Standard PPP options will be used e CISCO PPP Cisco PPP options will be used 2 Compression Turn on the Stac Compression The default for this field is Off 3 Multiple Link Options BOD Calculation Select the direction of the traffic you wish to calculate in order to determine when to add or subtract a link The default for this field is Transmit or Receive 56 Remote Node Configuration 4 Multiple Link Options Base Trans Rate Select the base data transfer rate for this Remote Node This parameter is in kilobits per second Kbps There are two options for this field e 64 Only one channel will be used e 128 Two channels will be used when a packet triggers a call 5 Multiple Link Options Max Trans Rate Enter the maximum data tr
52. e the number of links in multilink bundle Network Management The Prestige supports menu driven network management via an RS 232 or Telnet connection The Prestige is also equipped with a Call Detail Record CDR to help analyze and manage your telephone bill DHCP Support Dynamic Host Configuration Protocol DHCP Dynamic Host Configuration Protocol allows you to dynamically and automatically assign IP address settings to hosts on your network Security The Prestige supports PAP Password Authentication Protocol and CHAP Challenge Handshake Authentication Protocol Call Control The Prestige provides budget management for outgoing calls and maintains a blacklist for unreachable phone numbers in order to save you the expense of unnecessary charges Data Compression The Prestige incorporates Stac data compression and CCP Compression Control Protocol Networking Compatibility The Prestige is compatible with remote access products from other companies such as Ascend Cisco and 3Com Furthermore it supports Microsoft Windows 95 and Windows NT remote access capability Introduction 3 Applications For Your Prestige Some applications for the Prestige include Internet Access The Prestige supports the TCP IP protocol which is the language used for the Internet It is also compatible with access servers manufactured by major vendors such as Cisco and Ascend Internet Single User Account SUA For a small
53. ed incoming data filters outgoing data filters and call filters Data filters screen the data to determine if the packet should be allowed to pass Call filters are used to determine if a call should be placed Outgoing packets must pass through the data filters before they encounter the call filters Call filters are divided into two groups default call filters and user defined call filters Prestige has default call filters that filter out administrative packets e g RIP and SAP packets The Prestige applies the default filters first and then the user defined call filters if applicable as seen below Filter Configuration 77 Outgoing Packet Filtering Process Data Fitters Match CALL FILTERS Active Data Built In Default Call Fitters User Defined Call Fitters if applicable Initiate call if line not up Send Packet and reset Idle Timer Drop packet Drop packet if line not up if line not up Send packet Send packet but do not but do not reset Idle Timer reset Idle Timer Figure 8 1 Outgoing Packet Filtering Process For incoming packets the Prestige applies data filters only Packets are processed depending upon whether a match is made The Prestige allows you to customize the filter sets that you wish to use This following sections describe how to configure the Prestige s filter sets Prestige s Filter Structure You can configure up to twelve filter
54. ependent configuration will be covered in subsequent chapters For TCP IP see Chapter 7 From the Main Menu enter 11 to go to Menu 11 Remote Node Setup When in menu 11 enter the number of the Remote Nodes 1 to 4 that you wish to configure as shown below Remote Node Configuration 49 Menu ii Remote Hode Setup SJHQ Erm Enter Hode to Edit Figure 5 1 Menu 11 Remote Node Profile Enter the Remote Node number to edit and you will go to the next submenu 11 1 Remote Node Profile as shown below Menu 11 1 Remote Node Profile Rem Node Mame Node_1 Edit PPP Options Ho Active Yes Rem IP fAddr 192 68 135 1 Call Direction Outgoing Edit IP Ho Incoming Telco Option Rem Login Transfer Type 64K Rem Password Allocated Budget min A Rem CLID HA Period hr Call Back HA Out going Session Options My Login 2yxEL Input Filter Sets My Password Qutput Filter Sets Authen CHAP PAP Call Filter Sets Pri Phone t 5551212 Idle Timeout sec 300 Sec Phone H Press ENTER to Confirm or ESC to Cancel _ Figure 5 2 Menu 11 1 Remote Node Profile 1 Rem Node Name This is a required field Enter a descriptive name for the Remote Node e g SJHQ This field can support up to eight characters This name must be unique from any other Remote Node name or Remote Dial in User name Active Press the space bar to toggle between Yes and No When a Remote Node
55. equire hosts on both ends of the ISDN link to have separate addresses from the LAN and that the addresses must have the same network number If this is the case enter the IP address assigned to the WAN port of the Prestige Please note that this is the address assigned to the local Prestige not the remote router Sample IP Addresses 192 68 135 W 204 5 1 2 204 247 203 X Figure 7 3 Sample IP Addresses 7 Single User Account This field should be set to yes to enable the Single User Account Network Address Translation feature for this site Use the space bar to toggle between yes and no See page for more information on the Single User Account feature 8 Server IP address If you are using the Single User Account feature and you want to make a server accessible on your LAN e g a web server accessible to outside users enter that servers IP address here 72 TCP IP Configuration 9 Metric The metric represents the cost of transmission for routing purpose IP routing uses hop count as the measurement of cost with a minimum of 1 for directly connected networks Enter a number that approximates the cost for this link The number need not be precise but it must be between 1 and 16 In practice 2 or 3 is usually a good number 10 Private This parameter determines if the Prestige will include the route to this Remote Node in its RIP broadcasts If set to yes this route is kept private and not included in RIP br
56. er the IP address of the Prestige in dotted decimal notation four 8 bit numbers between 0 and 255 separated by periods e g 192 68 135 5 Please note that every machine on the TCP IP network must have a unique IP address IP Subnet Mask An IP address consists of two parts the network ID and the host ID The IP Subnet Mask is used to specify the network ID portion of the address expressed in dotted decimal notation The Prestige will automatically calculate this mask based on the IP address that you assign Unless you have special need for subnetting use the default subnet mask calculated by the Prestige RIP Direction This parameter determines how the Prestige handles RIP Routing Information Protocol If set to Both default the Prestige will broadcast its routing table on the LAN and incorporate RIP broadcasts by other routers into its routing table If set to In Only the Prestige will not broadcast its routing table on the LAN if set to Out Only the Prestige will broadcast its routing table but ignores any RIP broadcast packets that it receives If set to None the Prestige will not participate in any RIP exchange with other routers Usually you should leave this parameter at its default of Both and let RIP propagate the routing information automatically Installation 37 When you are finished press ENTER at the message Press ENTER to Confirm to save your selections or pres
57. ere are two different software updates RAS code and ISDN code e RAS and ISDN code update Type atur and wait until the Prestige responds with an OK to begin uploading the new software upload procedure varies depending on the type of software used to access the Prestige You must use the XMODEM protocol to perform the upload After uploading is System Maintenance 103 successful type atgo to start your Prestige Below is an example of downloading RAS and ISDN using PCPLUS To update software system needs to be rebooted After system is rebooted Enter Debug Mode will be displayed Please enter atur to upload RAS code Or enter atrs atis then atupx to upload ISDH code Do you want to continue Cy n Enter Debug Mode atur How erase flash ROM for uploading RAS code Starting MODEM upload S Programing successful IK atgo Initialing Driver Alt Z FOR HELP ANSI FOR 38400 H41 LOG CLOSED PRINT OFF OFF LINE Figure 11 9 Example of Uploading RAS Using PCPLUS Command interpreter Mode This option allows the user to enter the command interpreter mode This mode allows you to diagnose test and configure your Prestige using a specified set of commands A list of valid commands can be found by typing help at the command prompt For more detailed information please check ZyXEL Web site or send email to ZyXEL Support Group Call Contr
58. erent Local options This feature is used for UNIX application The Prestige will send three different types of syslog messages Call information messages i e CDR Error information messages and Session information messages Some examples of these messages are shown below Call Information Messages line channel 1 call 41 C01 Incoming Call 40001 line channel 1 call 41 C01 ANSWER Connected 64K 40001 line channel 1 call 41 C01 Incoming Call Call Terminated Error Information Messages line 1 channel 1 call 44 E01 CLID call refuse line 1 channel 1 call 45 E02 IP address mismatch Session Information Messages line 1 channel 1 call 41 101 IPCP up 306L line 1 channel 1 call 41 101 IPCP down 306L Diagnostic The diagnostic functions on your Prestige allow you to test aspects of your device to determine if they are working properly The following list provides a short description to the types of diagnostic tests available to your system System Maintenance 99 Menu 24 4 System Maintenance Diagnostic ISDH System Hang Up Bi Call 21 Reboot System Hang Up B2 Call 22 Command Mode Reset ISDH ISDN Connection Test Manual Call TCP IP ii Internet Setup Test 12 Ping Host Peer Enter Menu Selection Number Manual Call Remote MNode H A Host IP Address H A Figure 11 6 Menu 24 4 System Maintenance Diagnostic 1 From the Main Menu select option 24
59. ernet Terminal ISDN UTP ALI Line Computer Figure 3 1 Rear Panel Diagram A Warning On Connection Cables Several of the connection cables RS 232 ISDN line and Ethernet cable are very similar to each other It is important that you use Installation 21 the correct cable for each connection otherwise your Prestige could be damaged Connecting Your Computer and Your Prestige Warning Warning 22 Installation For the initial setup of your Prestige you must use RS 232 and communication software to configure the Prestige After the Prestige has been successfully installed you can modify the configuration through a remote Telnet connection See Chapter 10 for detailed instructions on using Telnet to configure your Prestige Connecting the RS 232 Cable to your Prestige One 9 25 pin adapter is included in your package To connect a RS 232 cable connect the 9 pin end of the cable to the DTE port on the back panel of the Prestige Connect the other end to the RS 232 cable connected to the serial port COM1 COM2 or any other COM port of your computer Connecting an ISDN Line to your Prestige Plug one end of your ISDN phone line which is included in your package into the socket on the rear panel of the Prestige labeled ISDN and the other end into the ISDN wall jack e S T interface This can only connect to your NT 1 Network Termination device Do not under any circumstances connect direct
60. etwork See LAN MAC address 96 Max Transmission Rate 55 MP 42 45 53 55 56 Multilink Protocol See MP North American ISDN 31 PABX 33 PAP 3 52 62 63 89 Password Authentication Protocol See PAP Ping 96 102 Plain Old Telephone Service See POTS Point to Point Protocol Multilink Protocol See PPP MP POTS 1 13 25 31 33 PPP MP 2 42 Remote Dial in Users 1 4 29 45 59 60 61 63 64 Remote Node 1 2 28 29 49 50 51 52 53 54 56 57 59 60 61 63 64 65 71 72 73 74 76 89 94 95 100 101 104 107 111 RIP 38 54 73 74 77 Routing Information Protocol See RIP RS 232 iv 3 21 22 24 91 92 96 103 109 S T Interface 2 11 22 SAP 77 96 Service Profile Identifier See SPID Single User Account 1 4 43 44 45 46 SMT 23 26 27 28 29 39 43 89 90 109 SPID 11 12 13 30 31 110 113 SUA See Single User Account switch types 2 13 31 110 113 System Management Terminal 26 See SMT Target Utility 55 57 TCP IP 2 4 14 36 37 40 43 49 59 69 80 81 82 85 92 102 Telco Options 43 53 54 62 Telecommuting 4 59 Telnet 3 7 22 90 91 92 103 U Interface 2 11 22 UNIX 72 98 99 UTP See 10Base T WAN 25 72 73 Warranty ii Warranty Card ii Index 117 worksheet 10 11 12 13 14 118 Index
61. exadecimal the value that the Prestige should use to compare with the masked packet The value should align with Offset Since Length is given in bytes you need to enter in twice the length hexadecimal numbers for this field For example if Length were 4 then a valid Value must have 8 hexadecimal numbers like 86 Filter Configuration 1155ABF8 If the result from the masked packet matches Value then the packet is considered matched Once you have completed filling in Menu 21 1 1 Generic Filter Rule press ENTER at the message Press ENTER to Confirm to confirm your selections or press ESC at any time to cancel your selections This data will now be displayed on Menu 21 1 Filter Rules Summary Filter Configuration 87 88 Filter Configuration 9 System Security About System Security For the Prestige The Prestige incorporates a number of security measures to prevent unauthorized access to your network For example the Prestige supports both PAP Password Authentication Protocol and CHAP Challenge Handshake Authentication Protocol in authenticating a Remote Node More information on CHAP and PAP can be found in Chapter 6 In addition the Prestige also implements a user password to get into the SMT screen You will have three attempts to enter the correct system password If you do not do so the SMT will kick you out In addition the Prestige will only support one user in the SMT at one time
62. extra fields Follow steps 1 8 from the previous section Internet Access Configuration 1 Single User Account Enter Yes to enable the Single User Account feature Use the space bar to toggle between Yes and No Single User Account IP Addr If your ISP assigns you a dynamic IP address enter 0 0 0 0 here If your ISP assigns you a static IP address enter that IP address here Single User Account Server IP Addr If you want to make a single server e g a Web server accessible to outside users enter that server s IP address here Press ENTER at the message Press ENTER to Confirm to confirm your selections or press ESC at any time to cancel your selections At this point the Prestige will ask if you wish to test the Internet connection If you select Yes the Prestige will call the ISP to test the Internet connection If the test fails note the error message that you receive and take the appropriate troubleshooting steps Configuring Backup ISP Accounts Sometimes it may be desirable to configure more than one ISP account for backup purposes The Single User Account feature can be enabled for all of these accounts making it convenient to switch Internet Service Providers in the event of a failure To configure a backup ISP 46 Configuring for Internet Access 5 Configure your primary ISP using Menu 4 as described earlier in this chapter Enter Menu 11 then select the number of an unused remote node
63. fer to the separate Warranty Card for your Return Material Authorization number RMA Products must be returned Postage Prepaid It is recommended that the unit be insured when shipped Any returned products without proof of purchase or those with an out dated warranty will be repaired or replaced at the discretion of ZyXEL and the customer will be billed for parts and labor All repaired or replaced products will be shipped by ZyXEL to the corresponding return address Postage Paid USA and territories only If the customer desires some other return destination beyond the U S borders the customer shall bear the cost of the return shipment This warranty gives you specific legal rights and you may also have other rights which vary from state to state Copyright 1997 by ZyXEL The contents of this book may not be reproduced in any part or as a whole or transmitted in any form or by any means without the written permission of the publisher Published by ZyXEL Communications Corporation All rights reserved Note ZyXEL does not assume any liability arising out of the application or use of any products or software described herein Neither does it convey any license under its patent rights nor the patents rights of others ZyXEL further reserves the right to make changes in any products described herein without notice This document is subject to change without notice Acknowledgments Trademarks mentioned in this manual are use
64. guration 49 Bandwidth on Demand 55 Editing PPP Options 56 6 Dial In Configuration 59 Telecommuting 59 Dial In Server Application 60 Default Dial In Setup 61 Dial In Users Setup 65 More on CLID 67 7 TCP IP Configuration 69 IP Subnet Mask 69 LAN to LAN Application 70 Remote Node Setup 71 Static Route Setup 73 8 Filter Configuration 77 About Filtering 77 Prestige s Filter Structure 78 Configuring a Filter Set 79 Configuring a Filter Rule 82 TCP IP Filter Rule 82 Generic Filter Rule 85 9 System Security 89 About System Security For the Prestige 89 Configuring the SMT Password 89 10 Telnet Configuration and Capabilities 91 About Telnet Configuration 91 Telnet Capabilities 92 Single Administrator 92 System Timeout 92 11 System Maintenance 93 System Status 93 Terminal Baud Rate 96 Log and Trace 97 View Error Log 98 Syslog And Accounting 98 Diagnostic 99 Backup Configuration 102 Restore Configuration 103 Software Update 103 Command Interpreter Mode 104 Call Control 104 Call Control Parameters 105 Blacklist 106 Budget Management 107 12 Troubleshooting 109 Problems Starting Up the Prestige 109 None of the LED s are on when you power up the Prestige 109 Connecting the RS 232 cable cannot access the SMT 109 Problems With the ISDN Line 110 The ISDN initialization failed 110 The ISDN loopback test failed 110 Problems with the LAN Interface 111 Can t PING any station on the LAN 111 Problems Connecting to a Remote
65. hrough the next filter rule before an action is taken There are two options for this field e Yes e No If More is Yes then Action Matched and Action Not Matched will be N A 14 Log In this field you can determine if you wish to log the results of packets attempting to pass the filter rule These results will be displayed on the System Log see Chapter 11 There are 4 options for this field e None No packets will be logged e Action Matched Only packets that match the rule parameters will be logged 84 Filter Configuration e Action Not Matched Only packets that do not match the rule parameters will be logged e Both All packets will be logged 15 Action Matched If the conditions for the filter rule are met you can specify what to do with the packet There are three options for this field e Check Next Rule e Forward e Drop 16 Action Not Matched If the conditions for the filter rule are not met you can specify what to do with the packet There are three options for this field e Check Next Rule e Forward e Drop Once you have completed filling in Menu 21 1 1 TCP IP Filter Rule press ENTER at the message Press ENTER to Confirm to confirm your selections or press ESC at any time to cancel your selections This data will now be displayed on Menu 21 1 Filter Rules Summary Generic Filter Rule This section will show you how to configure the protocol i
66. iance could void the user s authority to operate the equipment Shielded RS 232 cables are required to be used to ensure compliance with FCC Part 15 and it is the responsibility of the user to provide and use shielded RS 232 cables Information for Canadian Users The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operation and safety requirements The Industry Canada does not guarantee that the equipment will operate to a user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly The customer should be aware that the compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment For their own protection users should ensure that the electrical ground connect
67. ing LoopBack Test completed OK Hit any key to continue Figure 3 10 ISDN Loop back Test Screen TCP IP Ethernet Setup and DHCP Menu 3 is used to enter Ethernet related information as seen below Menu 3 Ethernet Setup Ethernet Interface 18BaseT Input Filter Sets Output Filter Sets DHCP Setup DHCP Server Client IP Pool Starting Address 6 0 8 1 Size of Clent IP Pool 0 Primary DHS Server 66 62 48 Secondary DNS Server 6 65 178 72 TCP IP Setup IP Address 204 247 203 174 IP Subnet Mask 255 255 255 192 RIP Direction Both Press ENTER to Confirm or ESC to Cancel Figure 3 11 Menu 3 Ethernet Setup Installation 35 36 Installation If you are setting up your network for the first time please read Chapter 4 Configuring for Internet Access before proceeding The chapter contains important information on how to assign IP addresses for your network 1 Ethernet Interface The Prestige supports two types of Ethernet connections the AUI 15 pin or the connection for the 10BaseT network looks like a bigger telephone plug Determine which type you are using and select the appropriate option in this field Input and Output Filter Sets Filter sets are used to block certain packets to reduce traffic and to prevent a security breach Filtering is a very involved subject so leave these fields blank for the time being After you have studied filtering in Chapter 8 come back an
68. ioning Feature Setting Term Type A Call Appearances CA 1 CA Quantity 1 Circuit Switched Voice CSV 1 CSV Flexible Call Offering FCO Unrestricted CSV limit 2 114 ISDN Switch Types Provisioning Feature Setting CSV Notification Busy NB limit 1 Circuit Switched Data CSD 1 CSD Flexible Call Offering FCO Unrestricted CSD limit 2 CSD Notification Busy NB limit 1 MTERM 2 Provisioning For the Northern Telecom Switch The Northern Telecom switch type supports two types of ISDN service These are National ISDN 1 and Custom For Northern Telecom National ISDN 1 EKTS Provisioning Feature Setting Signaling Functional Protocol Version Control PVC 2 National ISDN 1 TEI assignment Dynamic Maximum number of keys maxkeys 3 1 to 64 OK Release key No Ringing indicator No Electronic Key Telephone System Yes or No Additional Call Offering ACO Yes or No set to opposite of ACO Number of call appearances 2 EKTS Additional Call Offering ACO Notification Busy Limit 3 For Northern Telecom Custom Provisioning Feature Setting Signaling Functional Protocol Version Control PVC 1 Custom TEI assignment Dynamic Maximum number of keys maxkeys 3 1 to 64 OK Release key No Ringing indicator No Electronic Key Telephone System Yes or No Yes or No set to opposite of ACO ISDN Swit
69. ions of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make such connections themselves but should contact the appropriate electrical inspection authority or electrician as appropriate This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the radio interference regulations of Industry Canada The declarations of CE marking CE The Prestige 100 has been approved for connection to the Public Switched Telecommunication Network using interfaces compatible with ITU TSS recommendation 1 420 Basic Rate ISDN user access The Prestige 100 complies with the following directives vi 1 The Council Directive 89 336 EEC of 3 May 1992 on the approximation of the laws of the member states relation to Electro Magnetic Compatibility EMC Directive Council Directive 91 263 EEC of 29 April 1991 on the approximation of the laws of the Member States concerning telecommunication terminal equipment The Telecom Terminal Equipment Directive 93 68 EEC of 22 July 1993 amending the Directives 89 336 EEC 91 263 EEC and 92 31 EEC Marking Directive The Council Directive 92 31 EEC of 28 April 1992 amending directive on the approximation of the laws of the member states relating to Eletro Magnetic Compatibility Conta
70. is 30 e Retry Counter How many times a busy or no answer phone number is retried before it is put on the blacklist The default is 0 and the blacklist control is not enabled System Maintenance 105 e Retry Timer sec Elapse time after a call fails before another call may be retried Applies before a phone number is blacklisted Blacklist Menu 24 9 2 Blacklist Phone Humber 5551212 4age1 wh Remove Selection 1 14 Figure 11 11 Blacklist The phone numbers on this list cannot be entered directly instead they are numbers which have had problems connecting in the past The user can take a number off the list by entering the index number of entry 106 System Maintenance Budget Management Menu 24 9 3 Budget Management Remote Node Connection Time Total Budget Elapsed Timey Total Period 3860 6 00 6 08 8 67724 88 pa Jere eee bee ae Dial in User 6 00 4 08 8 00724 00 Reset Hode to update screen Figure 11 12 Budget Management The total budget is the time limit for an outgoing call to a Remote Node or Dial in User When this limit is reached the call will be dropped and further outgoing calls to that Remote Node or Remote Dial in User callback will fail After each period the total budget is reset The defaults for the total budget is O minutes and the period is 0 hours This means no budget control The user can reset the total outgoing call time through this menu
71. is fixed as DSS1 or 1TR6 2 B Channel Usage This field is fixed as Switch Switch 3 ISDN Data amp Subaddress Enter the telephone number and subaddress assigned to the ISDN data call for the Prestige It will be used as outgoing CGPN Calling Party Number setting for the ISDN data call Note that the Prestige only accepts digits please do not include and spaces in this field This field should be no longer than 19 digits for the number and 5 digits for the Subaddress The Subaddress is only available for DSS1 A B Adapter 1 amp Subaddress Enter the telephone number and subaddress assigned to the A B Adapter 1 POTS port 1 call for the Prestige It will be used as outgoing CGPN Calling Party Number setting for the A B Adapter 1 call A B Adapter 2 amp Subaddress Enter the telephone number and subaddress assigned to the A B Adapter 2 POTS port 2 call for the Prestige It will be used as outgoing CGPN Calling Party Number setting for the A B Adapter 2 call Dial Prefix to Access Outside Line Enter the prefix number if the Prestige is connected to an ISDN PABX This number will be added to all outgoing calls and should be no longer than 3 digits Otherwise leave this field blank PABX Number with S T Bus Number Enter the S T bus number if the Prestige is connected to an ISDN PABX If this field is left as blank then the loopback test will be skipped Incoming Phone Number Matching There are
72. ly to the ISDN wall jack e U interface This allows you to connect directly to your ISDN wall jack The ISDN jack is for ISDN line connection only Connection of a phone line may result in damage to your Prestige Attention La fiche ISDN est destin e uniquement pour la connexion sur une ligne RNIS La connexion sur une ligne t l phonique peut endommager votre Prestige Connecting a Telephone Fax to your Prestige If you wish you can connect a regular telephone fax machine or a modem to your Prestige to be used for analog calls just like a normal phone line It should be noted that this is optional and is not required for you to run other applications using your Prestige Plug one end of the telephone cord from a phone or fax or modem into the socket on the rear panel of the Prestige labeled PHONE 1 or PHONE 2 In order to receive incoming calls using a device connected to PHONE ports you need to enter Phonel or Phone in the Analog Call field under the desired telephone number e g Ist phone in SMT Menu 2 ISDN Setup See Collecting ISDN Phone Line Information in Chapter 2 for more details Connecting an Ethernet Cable to your Prestige The Prestige supports two types of Ethernet connections The connection procedure differs for each one please follow the one that is appropriate for your installation e UTP The UTP port is used to connect to a 10Base T network 10Base T networks use Unshiel
73. me shows the total outgoing call time for both B1 and B2 channels since the system has been powered up Ethernet shows the current status of the LAN connection on your Prestige Link shows the current status of the LAN Up or Down if it is 10Base T otherwise if it is configured as AUI this will show AUD TX Pkt the number of transmitted packets to LAN RX Pkt the number of received packets from LAN Collision number of collisions Name displays the system name of your Prestige This information can be modified in Menu 1 General Setup RAS S W Version refers to the version of the current RAS software ISDN F W Version refers to the version of the current ISDN firmware Ethernet Address refers to the Ethernet MAC address assigned to your Prestige System Maintenance 95 24 Country Code refers to the one byte country code value in decimal notation e g 225 indicates North America 25 LAN Packet Which Triggered Last Call shows the first 48 octets of the LAN packet that triggered the last outgoing call Two example figures are shown below the first of an ICMP Ping packet Type IP triggering the call and the second with a SAP broadcast packet Type Raw triggering the call With this information you can determine the source IP address of the packet or the source MAC address of the packet Source IP Address LAN Packet Which Triggered Last Call Type IP 45 00 OU 3C 02 12 OG H 3
74. n Europe Set to Phone2 if you wish to route the incoming analog call for this telephone number to PHONE port 2 Set to DOVBS if you wish to receive incoming Data Over Voice Bearer Service call SPID Number s The SPID Service Profile Identifier is a number used by a switch for identification purposes Depending on your switch type you may have zero one or two SPIDs assigned to your line For example if your switch type is Northern Telecom Custom you will have to enter two SPID numbers Installation 31 32 Installation DSS1 amp 1TR6 ISDN Menu 2 ISDH Setup Switch Type DSS 1 B Channel Usage Switch sSwitch ISDH Data 46181 Subaddress AvB Adapter 1 40102 Subaddress ACB Adapter 2 40103 Subaddress Dial Prefix to Access Outside Line PABX Humber Include T Bus Humber Incoming Phone Humber Matching Multiple Subscriber Number MSH Analog Call Routing HA Global Analog Call KeA Press ENTER to Confirm or ESC to Cancel Figure 3 8 Menu 2 ISDN Setup for DSS1 Menu 2 ISDN Setup Switch Type 1TR6 B Channel Usage SwitchSwitch ISDN Data 40161 A B Adapter i 40182 A B Adapter 2 40103 Dial Prefix to Access Outside Line PABX Humber Include S T Bus Number Incoming Phone Humber Matching Endgeraete Auswahl Ziffer EAZ Analog Call Routing H A Press ENTER to Confirm or ESC to Cancel Figure 3 9 Menu 2 ISDN Setup for 1TR6 1 Switch Type This field
75. n check the cables connecting your Prestige to your LAN The type of Ethernet interface that you have configured in menu 3 1 Verify that you are using the same AUI or 10BaseT as configured in this menu Verify with your network administrator that the IP address and the IP subnet mask configured in menu 3 2 are valid for that LAN Check the physical Ethernet cable and make sure the connections on the Prestige and also to the hub are secure Problems Connecting to a Remote Node or ISP 1 Check menu 24 1 to verify the ISDN status If it indicates down then refer to the section on the ISDN line problems In menu 24 4 5 do a manual call to that Remote Node You will see some messages printed onto the screen The messages will show you whether the call has been connected or not If the call is not connected verify the following parameters in menu 11 Pri mary Phone Sec ondary Phone and Transfer Rate If the call is connected but the call still terminates then there may be some kind of negotiation problem Verify the following parameters in menu 11 My Login My Password Route IP LAN Addr Also verify your IP address in menu 3 2 If you check the error log in menu 24 3 1 this will usually give you some logs regarding why the call was dropped If there is Troubleshooting 111 nothing in the log the call may have been dropped by the remote device that you dialed in to Make sure that the configuration paramete
76. ndependent parameters for a Generic filter rule for your Prestige For information on the protocol dependent fields refer to the previous section TCP IP Filter Rule The fields in the menu are indicated in bold type Filter Configuration 85 Menu 21 1 2 Generic Filter Rule Filter 1 Filter Type nk Filter Rule Active Yes Offset 4 Length 2 Mask fffF Ualue 8882 More Ho aa Hone fiction Matched Dro Action Not Matched check Next Rule Press ENTER to Confirm or ESC to Cancel Press Space Bar to Toggle Figure 8 5 Menu 21 1 1 Generic Filter Rule 1 Offset Offset refers to the value of the byte that you want to use as your starting offset That is in the data packet at what point do you want to begin the comparison The range for this field is from 0 to 255 Default 0 2 Length This field refers to the length in bytes of the data in the packet that the Prestige should use for comparison and masking The starting point of this data is determined by Offset The range for this field is 0 to 8 Default 0 3 Mask In this field specify in Hexadecimal the value that the Prestige should logically qualify and the data in the packet Since Length is given in bytes you need to enter in twice the length hexadecimal numbers for this field For example if Length were 4 then a valid Mask must have 8 hexadecimal numbers like 1155ABF8 4 Value In this field specify in H
77. ng The following list describes the fields involved in the trace and log options System Maintenance 97 View Error Log Selecting the first option from Menu 24 3 System Maintenance Log and Trace will display the Error Log in the system The Error Log does not only provide the error messages but it is also a source of information about your Prestige You can also clear the Error Log on your Prestige After each display you are prompted with an option to do so Enter the appropriate choice and press ENTER Syslog And Accounting Syslog and Accounting can be configured in Menu 24 3 2 System Maintenance Syslog and Accounting This menu configures the Prestige to send UNIX syslogs to another machine Menu 24 3 2 System Maintenance Syslog and Accounting Syslog Active Ho Syslog IP Address 7 Log Facility Local i Press ENTER to Confirm or ESC to Cancel Press Space Bar to Toggle Figure 11 5 Menu 24 3 2 System Maintenance Syslog and Accounting The User needs to configure the following 3 parameters to activate syslog 1 Active Use the space bar to turn on of off the syslog option 2 Syslog IP Address Input the IP Address that you wish to send your syslog to The address is usually written in dotted 98 System Maintenance decimal notation such as a b c d where a b c and d are numbers between 0 and 255 3 Log Facility Use the space bar to toggle between the 7 diff
78. nternet Access 41 Menu 4 Internet Access Setup ISP s Name myisp ISP IP Addr 18 145 233 5 Pri Phone H 5551000 Sec Phone H 5552000 My Login surfer My Password KEELELE single User Account No Server IP Addr HA Telco Option Transfer Rate 64K Press ENTER to Confirm or ESC to Cancel Figure 4 2 Menu 4 Internet Access Setup 1 From the Main Menu enter 4 to go to Menu 4 Internet Access Setup as seen above 2 ISP s Name Enter the name of your Internet Service Provider e g myisp This information is for identification purposes only 3 ISP IP Addr Enter the IP Address of the remote gateway at the ISP s site If you don t have this data just leave it blank 4 Pri mary Phone and Sec ondary Phone Number Both the Primary and the Secondary Phone number refer to the number that the Prestige will dial to connect to the ISP The Prestige will always call your ISP using the Primary Phone number first If the Primary Phone number is busy or does not answer the Prestige will call the Secondary Phone number if available Once connected the Prestige will use the BACP Bandwidth Allocation Control Protocol to establish the second B channel if PPP MP is enabled and the ISP also supports MP and BACP 5 My Login Name Enter the login name given to you by your ISP 42 Configuring for Internet Access 6 My Password Enter the password associated with the login name above
79. oadcast If no the route to this Remote Node will be propagated to other hosts through RIP broadcasts 11 RIP This parameter determines how the Prestige handles RIP Routing Information Protocol and the default is Both If set to Both the Prestige will broadcast its routing table on the WAN and incorporate RIP broadcasts by the other router into its routing table If set to In Only the Prestige will not broadcast its routing table on the WAN if set to Out Only the Prestige will broadcast its routing table but ignores any RIP broadcast packets that it receives If set to None the Prestige will not participate in any RIP exchange with other routers Usually you should leave this parameter at its default of Both and let RIP propagate the routing information automatically Once you have completed filling in the Network Layer Options Menu press ENTER to return to Menu 11 Press ENTER at the message Press ENTER to Confirm to save your selections or press ESC at any time to cancel your selections Static Route Setup On a directly connected internet RIP usually handles the routing automatically However RIP cannot propagate across isolated networks as in the case before a connection is made between the two subnetworks using one Class C IP address Without a route no packets can be forwarded to their destinations A static route is TCP IP Configuration 73 used to resolve this problem
80. ocated Budget min A Period hr Press ENTER to Confirm or ESC to Cancel _ Figure 6 3 Menu 13 Default Dial in Setup From the Main Menu enter 13 to go to Menu 13 Default Dial in Setup This section will describe how to configure the protocol independent fields in this menu For the protocol dependent fields please refer to the appropriate chapters 1 Telco Options CLID Authen This field sets the CLID authentication parameter for all incoming calls There are three options for this field e None No CLID is required e Required Must provide CLID or call is disconnected e Preferred If the CLID is available then CLID will be used to do authentication If the CLID is not available the call will continue 2 PPP Options Recv Authen This field sets the authentication protocol used for incoming calls User names and passwords are configured in the next section Remote users Dial in Users Setup Options for this field are e CHAP PAP Prestige will try CHAP first but PAP will be used if CHAP is not available e CHAP use CHAP only 62 Dial In Configuration e None no authentication required PPP Options Mutual Authen Some vendors e g Cisco implement a type of mutual authentication That is the node that initiates the call will request a user name and password from the far end that they are dialing to If the Remote Node that is dialing in implements this type of au
81. ol The Prestige provides two Call Control Management functions for the Remote Node and Remote Dial in User They are the Budget Management and Blacklist The Budget Management function provides the budget control for the outgoing call and a way for users to set a limit on their ISDN utilization to prevent any accidental usage It limits the total outgoing call time of the 104 System Maintenance Prestige over a period of time for each Remote Node amp Remote Dial in User callback only If the total outgoing call time exceeds the set limit future outgoing calls will not be made and the current call will be dropped The Blacklist function prevents the Prestige from re dialing to an unreachable phone number It is a list of phone numbers up to a maximum of 14 to which the Prestige will not make an outgoing call If the Prestige tries to dial to a phone number and fails a certain number configurable in the menu 24 9 1 times then the phone number will be put onto the blacklist The user has to enable the number manually again to be dialed Call Control Parameters Menu 24 9 1 Call Control Parameters Dialer Timeout Digital Call sec 35 Retry Counter 6 Retry Interval sec HA Press ENTER to Confirm or ESC to Cancel _ Figure 11 10 Call Control Parameters e Dialer Timeout Digital Call sec The Prestige will timeout if it can not set up an outgoing digital call within the timeout value The default
82. ompany installs your ISDN line please be sure to obtain the following information e ISDN switch type e ISDN telephone number s e ISDN Service Profile Identifiers SPID number s only for North America Collecting General Setup Information The Prestige requires certain system information You can obtain all the pertinent information from your network administrator Record this information into the worksheet as it becomes available This worksheet will later be referred to as you configure your Prestige e System Name This is the name given to the Prestige for identification purposes This name should be no more than 8 alphanumeric characters Spaces are not allowed but and _ are accepted Before You Begin 11 e Route IP Field For Internet access you will need to enable the Route IP Field Please see Chapter 4 for more details on configuring your Prestige for Internet access You have now collected all of the general setup information you need Please make sure that you have entered all the values onto the worksheet before proceeding to the next section Collecting ISDN Phone Line Information After you have successfully installed the ISDN phone line or if you already have one installed you need to use the ISDN line information to complete the worksheet and configure your Prestige Your telephone company can give you the following information to configure the Prestige Switch Type Geography No of Phon
83. omputer RS 232 Connect to ISDN Line Connect to Ethernet Cable Connect to Power Supply Configure Configure General Setup Configure ISDN Setup Configure TCPAP Ethernet Setup Congratulations Figure 2 1 Installation Guide Completing the Worksheet Before you continue locate the worksheet at the end of this chapter This information worksheet has been provided to help you get through setup and installation of your Prestige as easily as possible Ordering Your ISDN Line If you do not have the ISDN line installed already we suggest that you order it from your telephone company as soon as possible to avoid the long waits common when ordering a new line Use the 10 Before You Begin information in this section to place the order see Chapter 13 for information on provisioning your ISDN line If you have already installed your ISDN line you can check the following section to make sure that you can use all the features of your Prestige 1 Contact your local telephone company s ISDN Ordering Center 2 Find out what type of ISDN service is available Please refer to Chapter 13 to find out the provisioning information for the appropriate switch type and ISDN service For the U S the Prestige both U and S T Interface have been approved by Bellcore and have IOC ISDN Ordering Code S Capability EZ ISDN 1 3 Provide your telephone company with the proper provisioning information 4 When the telephone c
84. on The Prestige can also be used as a dial in server This application allows the Prestige to provide services for workstations on a remote network For the Prestige to be set up as a dial in server you need to configure the Default Dial In Setup to set the operational parameters for incoming call Additionally you will have to create a Remote Node for the router on the remote network see Chapter 5 An example of the Prestige being used as a dial in server is shown below 60 Dial In Configuration Prestige Acting as a Dial In Server Remote Network Local Network Prestige Dial In Server Figure 6 2 Example of a Dial In Server Application Default Dial In Setup This section covers the default dial in parameters The parameters in Menu 13 affect incoming calls from all Remote Dial in Users and Remote Nodes before authentication is completed Once authentication is completed and if it matches a Remote Node the Prestige will use parameters from that particular Remote Node Dial In Configuration 61 Menu 13 Default Dial in Setup Telco Options IP Address Supplied By CLID Authen Hone Dial in User Ho IP Pool Yes PPP Options IP Start Addr 204 5 1 1 Recu Authen CHAP PAP IP Gount 1 2 2 Compression Yes Mutual Authen Ho Session Options PAP Login H A Input Filter Sets PAP Password HA Output Filter Sets Multiple Link Options Idle Timeout 368 Max Trans Rate Kbps 128 Callback Budget Management All
85. ork number 192 68 135 0 into two you shift 1 bit from the host ID to the network ID Thus the new subnet mask will be 255 255 255 128 the first subnet will have network number 192 68 135 0 with hosts 192 68 135 1 to 129 68 135 126 and the second subnet will have network number 192 68 135 128 with hosts 192 68 135 129 to 192 68 135 254 It is recommended that you use the same subnet mask for all physical networks that share an IP network number The table below lists the additional subnet mask bits in dot decimal notations To use to following table write down the original subnet mask and substitute the higher order 0 s with the dot decimal of the additional subnet bits For instance to partition your class C TCP IP Configuration 69 network 204 247 203 0 with subnet mask 255 255 255 0 into 16 subnets 4 bits the new subnet mask becomes 255 255 255 240 Number of Bits Dot Decimal 1 128 192 224 240 248 252 254 255 LAN to LAN Application A typical LAN to LAN application is to use the Prestige to call from a branch office to the headquarters Up to four users can access the Prestige simultaneously on the LAN as depicted in the following diagram Branch Office Corporate HQ Figure 7 1 LAN to LAN Application For the branch office you need to configure a Remote Node in order to dial out to the headquarters Additionally you may also 70 TCP IP Configuration need to configure Stati
86. ormation is later used to configure the Prestige in routing an incoming analog call Set to Phonel or Phone if you wish to route the incoming analog call for this telephone number to PHONE port number 1 or 2 SPID Number s For North America only The SPID Service Profile Identifier is a number used by a central office switch for identification purposes With the switch information please see the previous table for the number of SPIDs you must enter You have now collected all of the necessary information about your ISDN phone line Make sure that these values are entered into your worksheet before you continue to the next section For DSS1 and 1TR6 ISDN please refer to Chapter 3 Before You Begin 13 Collecting Ethernet Setup Information e Ethernet Interface The first step is to determine the type of Ethernet interface you will be using on the Prestige There are two options AUI or UTP Record the interface type onto the worksheet If you have a 10Base2 BNC you should choose AUI e IP Address An IP Address is required for TCP IP protocol The IP Address is the unique 32 bit number assigned to your Prestige This address is written in dotted decimal notation four 8 bit numbers between 0 and 255 separated by periods e g 192 68 203 5 Record the IP Address into the worksheet as assigned by your network administrator Please note that every machine on an internet must have a unique IP address do not as
87. parameters such as Bandwidth On Demand Protocol Security etc while all Remote Dial in Users share one common set as defined in the Default Dial In Setup Menu 13 3 Generally Remote Dial in Users are individual users who dial in to the Prestige directly from their workstations while Remote Nodes represent networks and are used for LAN to LAN connections This chapter discusses how to setup Default Dial in parameters for both Remote Node and Remote Dial in User The following sections give two examples of how the Prestige can be setup as a dial in server for both Telecommuting Telecommuting enables people to work at remote sites and yet still have access to resources in the business office Typically a telecommuter will uses a client workstation with TCP IP or IPX and dial out capabilities e g a Windows 95 PC or a Macintosh and an ISDN Terminal Adapter TA For telecommuters to call in to your LAN you need to configure a Dial In User Profile for each Dial In Configuration 59 telecommuter Additionally you need to configure the Default Dial In Setup to set the operational parameters for all dial in users You can configure up to eight Remote Dial in Users for the Prestige An example of Remote Dial in User application telecommuting is shown below Remote User Configuration Prestige Same Network we 9 Remote User IP Addresses 0 Figure 6 1 Example of Remote User Telecommuter Dial In Server Applicati
88. restige is functioning properly ISDN LNK This LED indicates that the Prestige has an ISDN line connected to the WAN interface and it has been successfully initialized ISDN B1 and B2 These LEDs are on if there is an active WAN session on that channel or if that channel is making or receiving a call ETHERNET LNK This LED indicates that the Prestige has been successfully connected to the LAN via a UTP Ethernet interface ETHERNET TX and RX Transmit and Receive LEDs will blink to indicate when there is traffic over the LAN ETHERNET COL This LED indicates that there is transmission collision over the LAN PHONE 1 This LED indicates the functionality of the POTS port 1 on the Prestige If there is a device plugged into this port and the device is in use this LED should be on PHONE 2 This LED indicates the functionality of the POTS port 2 on the Prestige If there is a device plugged into this port and the device is in use this LED should be on Powering On Your Prestige When you power on your Prestige the Prestige will perform several internal tests and will also do an ISDN line initialization After this initialization the Prestige will ask you to press ENTER to continue as shown below Installation 25 26 Installation Copyright c gt 1994 1996 ZyXEL Communications Corp RAS Version UL ifa 9 4 96 ethernet address 8B aic5 48 66 83 Resetting ISDN firmware Switch Type is
89. rs between these two devices are consistent Problems Connecting to a Remote User 1 112 Troubleshooting First verify that you have configured the authentication parameters in menu 13 These would be CLID Authen Recv Authen and Mutual Authen If the Remote Dial in User is negotiating IP verify that the IP address is supplied correctly in menu 13 Check that either the Remote Dial in User is supplying a valid IP address or that the Prestige is assigning a valid address from the IP pool In menu 14 verify the user name and password for the Remote Dial in User 73 ISDN Switch Types The following table summarizes the different type of switch types supported by the Prestige and some related information on the switch types number of phone numbers and SPID numbers It should be noted that the information in this table is for the common case and is recommended for those cases Exceptions still exist to these figures You can locate the provisioning information for the appropriate North American switch type in the next sections Switch Type Geography No of Phone s No of SPIDs AT amp T 5ESS NI 1 North American 2 2 AT amp T 5ESS Point to North American 1 0 Point AT amp T 5ESS Multipoint North American 2 2 Northern Telecom NI 1 North American 2 2 Northern Telecom Custom North American 2 2 DSS1 Europe Asia 2 N A 1TR6 Germany 2 N A Provisioning For U S Switches For the
90. s ESC at any time to cancel them 38 Installation Configuring for Internet Access Menu 4 of the SMT allows you to configure Internet access on one screen Before you configure the Prestige for Internet access you need to collect the following information from your ISP Internet Service Provider e IP address of the ISP s gateway optional e Telephone number s of your ISP e Login name e Password for ISP authentication For your Workstation e Domain Name Server DNS Configuring for Internet Access 39 204 247 203 129 Prestige Figure 4 1 Internet Access IP Addresses and the Internet Conventionally the Internet with a capital I refers the large scale interconnected networks across the world that was originally developed by the US Department of Defense The Internet uses exclusively the TCP IP protocols The term internet lower case i however refers to any interconnected networks using any protocol An internet can be as simple as two hosts on a LAN or it can be as complex as the Internet itself Every machine on the Internet must have a unique address within that internet If your networks are isolated from the Internet e g only between your two branch offices you can assign any IP addresses to the hosts without problems However the Internet Assigned Numbers Authority IANA has reserved the following three blocks of IP addresses specifically for private networks 10 0 0 0 10 255 259 2
91. se requirements include 6 Introduction An ISDN telephone line which has been installed by your telephone company An Ethernet connection to your computer e A computer equipped with communications software configured to the following parameters e VT100 terminal emulation e 9600 Baud rate e No parity 8 Data bits 1 Stop bit After the Prestige has been successfully connected to your network you can make future changes to the configuration by using a Telnet application Please make sure that you have all of these components before you attempt to install your Prestige Introduction 7 8 Introduction 2 Before You Begin To ensure successful installation of your Prestige we strongly recommend that you carefully follow the steps outlined in Chapters 2 and 3 These chapters are designed as a guide for you to collect the necessary information about your ISDN phone line and the LAN which you will be connected to Once this information has been collected it will be used to configure your Prestige After you have successfully configured your Prestige please see the appropriate chapters to setup your application For Internet Access please see Chapter 4 Road Map and Flow Below is a schematic flowchart It is intended to guide you through a successful installation of your Prestige Before You Begin 9 Collect Collect General Setup Info Collect ISDN Line Info Collect Ethernet Setup Info Connect Connect to C
92. sign an arbitrary address to any machine e IP Sub net Mask This field is required for TCP IP protocol An IP address consists of two parts the network ID and the host ID The IP Subnet Mask is used to specify the network ID portion of the address expressed in dotted decimal notation The Prestige will automatically calculate this mask based on the IP address that you assign Unless you have special need for subnetting use the default mask as calculated by the Prestige The table below lists some examples of IP subnet masks and the number of hosts that are allowed Consult your network administrator if you are unsure of this value IP Subnet Mask Number of Host ID s Number of Bits 255 255 255 0 254 24 255 255 255 128 126 25 255 255 255 192 62 26 14 Before You Begin IP Subnet Mask Number of Host ID s _ of Bits 255 255 255 224 30 255 255 255 255 1 7 Before You Begin 15 Prestige Setup and Installation Worksheet General Setup Information e System Name for identification purposes e Protocol Routing ___ TCP IP ISDN Setup Information e Switch Type check one ___AT amp T 5ESS NI I ___AT amp T Point to Point AT amp T 5ESS Multipoint ___ Northern Telecom NI 1 ___ Northern Telecom Custom __DSS1 __1TR6 e B Channel Usage check one ___ Switch Switch ___ Switch Unused North America ISDN 16 Before You Begin e 1st Telephone Number e Analog Call check one _
93. stem 4 Command Mode This option allows the user to enter the command mode This mode allows you to diagnose and test your Prestige using a specified set of commands Backup Configuration Selecting option 5 from Menu 24 Maintenance will allow you to backup your current Prestige configuration onto disk Backup is 102 System Maintenance highly recommended once your Prestige configuration is functioning You need to download the configuration onto disk Procedure for downloading varies depending on the type of software used to access the Prestige but you must use the XMODEM protocol to perform the download Restore Configuration Selecting option 6 from Menu 24 Maintenance will restore backup configuration from disk to the Prestige You need to upload a backup file to the Prestige Procedure for uploading varies depending on the type of software used to access the Prestige but you must use the XMODEM protocol to restore the configuration Please keep in mind that configuration is stored on flash ROM in the Prestige so even if power failure were to occur your configuration is safe Software Update Software updates are only possible through the RS 232 cable connection You cannot use telnet to update the software version of your Prestige Please note that this function will delete the old software before installing the new software Do not attempt to utilize this menu unless you have the new software version Th
94. t that you follow the steps outlined in Part One Chapters 1 3 to correctly connect your Prestige to your LAN You can then refer to other chapters of the manual depending on which applications you wish to use What This Manual Doesn t Cover This manual assumes that you know how to use your computer and are familiar with your communications software If you have questions about using either one refer to the manual for the product Other Resources For more information about the Prestige 100 check the following sources e Prestige 128 100 Quick Start Guide e Prestige Support Disk e Release notes for firmware upgrades and other information can be accessed through a ZyXEL FTP server site For ZyXEL contact information see page vi Introduction 5 Packing List Before you proceed further please check all items you received with your ISDN router against this list to make sure nothing is missing The complete package should include One Prestige 100 One power adapter One RJ 45 phone cable One RJ 11 phone cable One 25 pin female 9 pin male adapter One LAN crossover cable red tag One LAN straight cable white tag One Prestige Support Disk One Prestige 128 100 Quick Start Guide This Prestige 100 User s Manual Additional Installation Requirements In addition to the contents of your package there are other hardware and software requirements you need before you can install and use your Prestige The
95. thentication set this field to Yes PAP Login This field will only be enabled if the Mutual Authen field is set to Yes Enter in the login name to be used to respond to the far end s PAP authentication request This field does not apply to CHAP authentication PAP Password This field will only be enabled if the Mutual Authen field is set to Yes Enter in the PAP password to be used to respond to the far end s authentication request This field does not apply to CHAP authentication Multiple Link Options Max Trans Rate Enter the maximum data transfer rate between your Prestige and the Remote Dial in User The unit is in bits per second There are two options for this field e 64 At most one B channel will be used e 128 A maximum of two channels can be used When the Prestige calls back to the Remote Dial in User the maximum data transfer rate is always 64 Callback Budget Management Allocated Budget min This field will set a budget callback time for all the Remote Dial in Users The default for this field is 0 for no budget control Callback Budget Management Period hr This field will set the time interval to reset the above callback budget control Dial In IP Address Supplied By Dial in User If set to Yes it tells the Prestige to allow a remote host to specify its own IP Dial In Configuration 63 address This is to prevent the remote host from using an invalid
96. three options in this field e Multiple Subscriber Number MSN The digital call will only be answered when there is a match for the ISDN data number The analog call will be answered as the A B Adapter 1 call when there is a match for the A B Adapter 1 number Or it will be answered as A B Adapter 2 call when there is a match for the A B Adapter 2 number If no A B Adapter 1 or 2 number is specified then the analog call will not be answered This option will be available as EAZ Endgeraete Auswahl Ziffer for 1TR6 e Called Party Sub Address CDSA The digital call will be answered when there is a match for the ISDN Data subaddress The analog call will be answered as the A B Installation 33 34 Installation Adapter 1 call when there is a match for the A B Adapter 1 subaddress Or it will be answered as A B Adapter 2 call when there is a match for the A B Adapter 2 subaddress If A B Adapter or 2 subaddress is specified then the analog call will not be answered This option is only available for DSS1 e Don t care all numbers accepted All digital calls including global calls without CDPN and CDSA in the call setup to any CDPN Called Party Number will be answered All analog calls will be routed to the A B Adapter 1 A B Adapter 2 or not answered This depends on the setting of Analog Call Routing All global analog calls will either accept or not answer them depending on the setting of Global Analog Call
97. tion Start dialing for node lt i gt HHH Hit any key to continue tHHt Dialing chan lt 2 gt phone last digit 48181 Call CONNECT speed lt 64008 gt chan lt 2 gt prot lt 1 gt up CHAP send response CHAP login to remote ORK IPCP negotiation started IPCP up Figure 11 7 Trace Display for a Successful IPCP Connection via Manual Call Below is an example of a failed Trace Display for a Successful IPCP Connection via Manual Call System Maintenance 101 Start dialing for node lt i gt Hit any key to continue iHHt Dialing chan lt gt phone last digit 40181 Call COHHECT speed lt 64008 gt chan lt 2 gt prot lt i gt up CHAP send response xxLogin to remote failed Check name passud Receive Terminate REQ LCP down Line Down chan lt 2 gt Figure 11 8 Trace Display for a Failed IPCP Connection via Manual Call 1 Internet Setup Test This test checks to see if your Internet access configuration has been done correctly When this option is chosen the Prestige will PING the Internet IP Address If everything is working properly you will receive an appropriate response Otherwise note the error message and consult your network administrator 2 Ping Host This diagnostic test pings the host which determines the functionality of the TCP IP protocol on your system 3 Reboot System This option reboots the system This serves to implement any changes that may have been recently added to your sy
98. umber this will bring you to Figure 6 2 Menu 14 1 Edit Dial in User Menu 14 1 Edit Dial in User User 1 User Name joesmith Active Yes Passud 2sese2csescsese Callback No Callback Phone H A Callback Override M A Rem CLID Idle Timeout 308 Press ENTER to Confirm or ESC to Cancel _ Figure 6 5 Menu 14 1 Edit Dial in User 1 User Name This is a required field This will be used as the login name for authentication Choose a descriptive word for login e g brentharper 2 Active You can disallow dial in access to this user by setting this field to Inactive When set to inactive the user record is still kept in the database for later activation Deactivated users are displayed with a minus sign at the beginning of the name in Menu 14 Password Enter the password for the Remote Dial in User 4 Callback This field determines if the Prestige will allow call back to the Remote Dial in User upon dial in If this option is enabled the Prestige will be able to call back to the Remote Dial in User if they request it In such a case the Prestige will disconnect the initial call from this user and dial back to the specified call back number see below The default is no callback 66 Dial In Configuration Callback Phone If Callback is Yes then this is a required field Otherwise an N A will appear in the field Enter the telephone number to which the Prestige
99. will call back Callback Override If Callback is No an N A will appear in the field The callback override allows the Remote Dial in User to specify the call back telephone number on call by call basis This is useful for when the Prestige returns a call back to a mobile user at different numbers e g a sales rep in a hotel Please note that the default is No i e the Prestige always calls back to the fixed callback number Rem CLID If you have enabled the CLID Authen field in Menu 13 then you need to specify the telephone number from which this Remote Dial in User calls The Prestige will check this number against the CLID in the incoming call If they do not match and the CLID Authen is Required then the Prestige will reject the call Idle Time out Enter the idle time in seconds This time out determines how long the dial in user can be idle before the Prestige disconnects the call Idle time is defined as the period of time where there is no data traffic between the dial in user and the Prestige The default is 300 seconds 5 minutes Once you have completed filling in Menu 14 1 Edit Dial in User press ENTER at the message Press ENTER to Confirm to save your selections or press ESC at any time to cancel your selections More on CLID CLID allows the Prestige to authenticate the caller before a call is answered thus saving the cost of a connection The Prestige uses the c

ZyXEL zyxel Prestige100 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents