ZyXEL BPS-120 User's Manual
Contents
1. 15 BPS 120 User s Guide Table 2 BPS 120 System States and Internal System Indicators BPS 120 STATE PWR TEMP FAN FAULT On The detected an internal system problem or external power fault BPS 120 has Each rear panel OUTPUT port has a corresponding GREEN RED AMBER LED to indicate its own state as shown in Figure 7 and Table 3 and Table 4 Typically the system operator need only monitor the LED indicators on the BPS 120 front panel to ensure externally connected systems are operating normally Figure 7 BPS 120 Front Panel DC Output LED Detail Table 3 Front Panel DC Output Power Output LEDs NO ACTIVE INACTIVE POWER STANDBY DEVICE CONNECTION FEEDING FAULT GREEN Off On On On Off Off AMBER Off Off On Off On Off RED Off Off Off On Off On 16 BPS 120 User s Guide Table 4 BPS 120 Front Panel DC Output LEDs State Definitions PORT LED COLOR DC DESCRIPTION INDICATIONS OUTPUT LED STATUS NO Green Off No external device is connected to OUTPUT CONNECTION 1 6 NO Amber Off No external device is connected to OUTPUT CONNECTION 1 6 NO Red Off No external device is connected to OUTPUT CONNECTION 1 6 ACTIVE Green On External device is connected to OUTPUT1 6 but no backup power is supplied ACTIVE Amber Off External device is connected to OUTPUT 1 6 but no backup2. BPS 120 Stand Alone Backup Power System User s Guide Version 1 0 October 2004 ZyXEL Unleash Networking Power BPS 120 User s Guide 1 Copyright Copyright 2004 by ZyXEL Communications Corporation The contents of this publication may not be reproduced in any part or as a whole transcribed stored in a retrieval system translated into any language or transmitted in any form or by any means electronic mechanical magnetic optical chemical photocopying manual or otherwise without the prior written permission of ZyXEL Communications Corporation Published by ZyXEL Communications Corporation All rights reserved Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products or software described herein Neither does it convey any license under its patent rights nor the patent rights of others ZyXEL further reserves the right to make changes in any products described herein without notice This publication is subject to change without notice Trademarks Trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners 2 Interference Statements and Warnings FCC Interference Statement This switch complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This switch may not cause harmful interference 2 This switch must accept any interference received
3. Guide should be lit when connecting external devices then toggle the STANDBY ACTIVE mode switch shown in Figure 6 to active mode to update OUTPUT 1 6 priority and sense new power readings at the output ports The ACTIVE LED should light You should toggle the front panel STANDBY ACTIVE switch after turning the BPS 120 on forcing it to sense and update its remote device power readings on OUTPUTs 1 6 ZyXEL BPS 120 STANDBY ACTIVE Figure 6 BPS 120 Front Panel STANDBY ACTIVE In general the BPS 120 may be in one of the following states ACTIVE STANDBY or FAULT as indicated by their corresponding front panel LEDs shown in Figure 6 The BPS 120 also includes advanced self diagnostic monitoring features to ensure that its own circuitry is functioning normally the PWR TEMP and FAN LEDs indicate these states This information is described in Table 2 Table 2 BPS 120 System States and Internal System Indicators BPS 120 PWR TEMP FAN STATE ACTIVE On The GREEN GREEN GREEN A The BPS 120 The BPS 120 The BPS in ACTIVE F mode internal power internal 120 internal module is temperature is fans are functioning within normal operating normally limits normally STANDBY On The RED RED RED e The BPS 120 The BPS 120 The BPS in STANDBY A i mode internal power has an internal 120 internal module has over fan s are failed temperature not problem operating properly
4. arranty ZyXEL warrants to the original end user purchaser that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase During the warranty period and upon proof of purchase should the product have indications of failure due to faulty workmanship and or materials ZyXEL will at its discretion repair or replace the defective products or components without charge for either parts or labor and to whatever extent it shall deem necessary to restore the product or components to proper operating condition Any replacement will consist of a new or re manufactured functionally equivalent product of equal value and will be solely at the discretion of ZyXEL This warranty shall not apply if the product is modified misused tampered with damaged by an act of God or subjected to abnormal working conditions NOTE Repair or replacement as provided under this warranty is the exclusive remedy of the purchaser This warranty is in lieu of all other warranties express or implied including any implied warranty of merchantability or fitness for a particular use or purpose ZyXEL shall in no event be held liable for indirect or consequential damages of any kind of character to the purchaser To obtain the services of this warranty contact ZyXEL s Service Center for your Return Material Authorization number RMA Products must be returned Postage Prepaid It is recommended that the unit b
5. cted AC Make sure you are using the LED is off power supply correct power line cord and it is plugged into an appropriate 100 240 VAC power supply receptacle Check the power line fuse Unplug the power line cord and plug it in again Turn the BPS 120 on using the rear panel switch If the error persists you should contact your vendor or Zyxel for servicing The STANDBY LED is on The BPS 120 is in standby mode Press the STANDBY ACTIVE button to put the BPS 120 into active mode The FAULT LED is red The BPS 120 has an internal hardware system fault PWR TEMP or FAN LEDs are red Monitor the PWR TEMP and FAN LEDs then turn the BPS 120 off or disconnect external devices 18 BPS 120 User s Guide Table 5 BPS 120 Troubleshooting Tips PROBLEM CONDITION CORRECTIVE ACTION The PWR LED is DC output power is The internal power supply is red unavailable or not operating defective or the BPS 120 has properly detected an overcurrent Press the STANDBY ACTIVE button If the FAULT LED does not turn off and the PWR LED does not turn green cycle the power on the BPS 120 using the rear panel switch If the problem persists replace the BPS 120 The TEMP LED is red BPS 120 internal temperature has exceeded limit Reduce the ambient temperature The FAN LED is red Fan speed is wrong too fast too slow or one of the four fans has stoppe
6. d operating A fan is defective Replace the BPS 120 Table 6 Technical Specifications for the BPS 120 AC Input Voltage 100 240 VAC 50 60 Hz Power Overload protection power module fuse 1 8A Max internal universal power supply 120 W per port 12 VDC output Power consumption 180W maximum AC Operating Temperature 0 C 45 C 32 F 113 F Storage Temperature 25 C 70 C Operational Humidity 10 90 non condensing Weight 4 0 kg Dimensions rack 19 rack mountable width 1U height 19 BPS 120 User s Guide Table 6 Technical Specifications for the BPS 120 Safety UL 60950 1 CSA 60950 1 EN60950 1 IEC 60950 1 EMC FCC Part15 Class A CE EMC Class A 20
7. e insured when shipped Any returned products without proof of purchase or those with an out dated warranty will be repaired or replaced at the discretion of ZyXEL and the customer will be billed for parts and labor All repaired or replaced products will be shipped by ZyXEL to the corresponding return address Postage Paid This warranty gives you specific legal rights and you may also have other rights that vary from country to country ZA Online Registration Register online registration at www zyxel com for free future product updates and information BPS 120 User s Guide 5 Customer Support When you contact your customer support representative please have the following information ready Please have the following information ready when you contact customer support e Product model and serial number e Warranty Information e Date that you received your device Brief description of the problem and the steps you took to solve it SUPPORT E MAIL TELEPHONE WEB SITE REGULAR MAIL SALES E MAIL FAX FTP SITE WORLDWIDE support zyxel com tw 886 3 578 www zyxel com ZyXEL Communications aoe www europe zyxel com Corp i 6 Innovation Road II ftp zyxel com Science Park Hsinchu 300 sales zyxel com tw pa ftp europe zyxel com Taiwan NORTH support zyxel com 1 800 255 www us zyxel com ZyXEL Communications AMERICA 4101 ine 1 714 632 1130 N Miller St Anaheim a CA 92806 2001 sales zyxel com 1 714 632 ftp us zy
8. eshooting information Figure 4 BS 120 Rear Panel Showing OUTPUT Port Power Connections 12 BPS 120 User s Guide 14 13 12 11 10 9 8 Figure 5 BPS 120 OUTPUT Port Connector Pin Diagram and Cable 13 BPS 120 User s Guide Table 1 BPS 120 OUTPUT Port Connector s 1 6 Pin Definition PIN NUMBER DESIGNATION 1 GND 2 N A 3 12V 4 12V 5 12V 6 12V 7 GND 8 GND 9 N A 10 BPS present 11 BPS StatusO 12 BPS Status1 13 Power good 14 GND 2 4 Front Panel and LED Displays The BPS 120 defaults to STANDBY mode when the BPS 120 is switched on Depress the front panel dual function STANDBY ACTIVE switch to place the BPS 120 in active mode capable of supplying power to remote devices System and remote power status information are shown on the front panel of the BPS 120 using two groups of LED displays the first group shown in Figure 6 monitors internal BPS 120 parameters and the system mode standby active the second group of LEDs shown in Figure 7 shows status information for each of the six power OUTPUT ports Enabling backup power to any of six external devices is as simple as connecting the supplied system power cables from each OUTPUT 1 6 on the back panel of the BPS 120 to external devices Be sure the BPS 120 is in standby mode the STANDBY LED 14 BPS 120 User s
9. g this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly The customer should be aware that the compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment For their own protection users should ensure that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution BPS 120 User s Guide Users should not attempt to make such connections themselves but should contact the appropriate electrical inspection authority or electrician as appropriate Note This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the radio interference regulations of Industry Canada 4 ZyXEL Limited W
10. including interference that may cause undesired operations FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital switch pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to BPS 120 User s Guide radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Taiwanese BSMI Bureau of Standards Metrology and Inspection A Warning FER SE SICA Ss ES ER A RES RAT ie TEREN F e AE W ES A SL mes Certifications Refer to the product page at www zyxel com 3 Information for Canadian Users The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operation and safety requirements The Industry Canada does not guarantee that the equipment will operate to a user s satisfaction Before installin
11. k by lining up the holes in the brackets with the appropriate holes on the rack Secure the BPS 120 to the rack with the rack s mounting screws Figure 3 Rack Mounting the BPS 120 11 BPS 120 User s Guide 2 3 Attaching Power Cables and Connector Definition The BPS 120 includes power connection cables for up to six 6 external devices The rear connector pin out diagram and power signal descriptions are shown in the following Figure 5 and Table 1 for OUTPUTs 1 6 Backup power is supplied by inserting power cables into any of the OUTPUTs 1 6 on the rear panel of the BPS 120 and into the corresponding power input connector of device s such as switches or routers The power connector cables may be inserted only one way There is no need to worry about inserting the power cables incorrectly as they are keyed for one position Backup power for externally connected devices is supplied based upon output port priority with OUTPUT 1 having the highest priority That is an external device connected to OUTPUT 1 has backup power priority over devices connected to OUTPUTs 2 6 OUTPUT 2 has backup power priority over devices connected to OUTPUTs 3 6 etc To turn the BPS 120 on connect the power line cord to a 100 240 VAC power outlet and move the rocker switch on the rear panel from the 0 to 1 position The STANDBY PWR TEMP and FAN LEDs will then light on the front panel If they do not light up see Table 5 for troubl
12. naasnnnnnannn 9 2 Hardware Installation and Connections 00vrrrreeeererrrassanannassssonnannannnnnnnannnnnn 9 2 1 Desktop Installation ccccececccceeceeeeeeeeeecnecaeceeeeeeeseceeeaeeeeeeesesenniaaeeeeees 10 2 2 Rack mounted Installation 0 cccccccceeeeeccaeceeeeeeeseceneaeeeeeeesesensuaeeeeeees 10 2 3 Attaching Power Cables and Connector DefinitiON oerreeeeroroes 12 2 4 Front Panel and LED DisplayS cccceccceeeeeeeeeeeeeeeeeneeeeeeeneeeeetneeeeeeea 14 3 TroubleSHOOUNQ wii sonecesccttcecescteceessccten kaa io kai kenn oak ak n on dkadi saa an po ck taa sann ikani 18 BPS 120 User s Guide 1 Introducing the BPS 120 The BPS 120 is a backup power system to which you can connect up to six of ZyXEL s devices that have a 12VDC external backup power supply connector The BPS 120 monitors the power status of the connected devices and immediately provides backup power to a device that loses power or has a hardware power failure The BPS 120 can supply power to one device at a time Figure 1 BPS 120 Backup Power System The BPS 120 has the following features Six 6 output power ports for connecting devices Individual front panel LEDs to show status for each output power port internal power hardware internal fans and internal temperature Fast power switchover ensures that a power failure on a connected device does not cause it to restart Reduced form factor facilitates
13. power is supplied ACTIVE Red Off External device is connected to OUTPUT 1 6 but no backup power is supplied INACTIVE Green On Output port is unavailable to supply external power because another is in use INACTIVE Amber On Output port is unavailable to supply external power because another is in use INACTIVE Red Off Output port is unavailable to supply external power because another is in use POWER Green On The BPS 120 is providing power to the FEEDING connected device POWER Amber Off The BPS 120 is providing power to the FEEDING connected device POWER Red On The BPS 120 is providing power to the FEEDING connected device STANDBY Green Off The BPS 120 is in standby mode STANDBY Amber On The BPS 120 is in standby mode STANDBY Red Off The BPS 120 is in standby mode DEVICE Green Off The BPS 120 has detected an external or FAULT internal fault See Table 5 17 BPS 120 User s Guide Table 4 BPS 120 Front Panel DC Output LEDs State Definitions PORT LED COLOR DC DESCRIPTION INDICATIONS OUTPUT LED STATUS DEVICE Amber Off The BPS 120 has detected an external or FAULT internal fault See Table 5 DEVICE Red On The BPS 120 has detected an external or FAULT internal fault See Table 5 3 Troubleshooting Make sure that the BPS 120 is plugged into an appropriate AC power supply Table 5 BPS 120 Troubleshooting Tips PROBLEM CONDITION CORRECTIVE ACTION The STANBY Faulty or not conne
14. rack mounting and high density deployment 2 Hardware Installation and Connections BPS 120 User s Guide Do not block the device s rear panel or the side panel ventilation holes Leave space between devices when stacking 2 1 Desktop Installation 1 Set the BPS 120 upside down on a sturdy level space with a 100 240 VAC power outlet nearby 2 Make sure there is enough clearance near the BPS 120 to allow air circulation the attachment of cables and the power line cord 3 Remove the adhesive backing from the supplied rubber feet 4 Attach the rubber feet to each corner on the bottom of the BPS 120 These rubber feet help protect the BPS 120 from shock and or vibration and ensure space bewteen devices when stacking 5 Turn the BPS 120 right side up after you have attached the rubber feet a Figure 2 Attaching the Rubber Feet 2 2 Rack mounted Installation The BPS 120 can be mounted on an EIA standard size 19 inch rack or in a wiring closet with other equipment Follow the steps below to mount your BPS 120 on a standard EIA rack using the included rack mounting hardware 1 Align one bracket with the holes on one side of the BPS 120 and secure it with the bracket screws Similarly attach the other bracket to the opposite side of the BPS 120 10 BPS 120 User s Guide Figure 2 Attaching the Rack Mounting Brackets 2 After attaching both mounting brackets position the BPS 120 in the rac
15. xel com USA 0858 GERMANY support zyxel de 49 2405 www zyxel de ZyXEL Deutschland 6909 0 GmbH Adenauerstr 20 A2 D 52146 sales zyxel de 49 2405 Wuerselen 6909 99 Germany FRANCE info zyxel fr 33 0 4 72 52 www zyxel fr ZyXEL France 97 97 1 rue des Vergers Bat 1 C ee ae 12 52 69760 Limonest France SPAIN support zyxel es 34 902 195 www zyxel es ZyXEL Communications 420 Alejandro Villegas 33 3 i sales zyxel es 34 913 005 i lt 28049 Madrid 345 pain 4 is the prefix number you enter to make an international telephone call BPS 120 User s Guide DENMARK NORWAY SWEDEN FINLAND SUPPORT E MAIL SALES E MAIL support zyxel dk sales zyxel dk support zyxel no sales zyxel no support zyxel se sales zyxel se support zyxel fi sales zyxel fi TELEPHONE WEB SITE FAX FTP SITE 45 39 55 07 www zyxel dk 00 45 39 55 07 07 47 22 80 61 www zyxel no 80 47 22 80 61 81 46 31 744 www zyxel se 7700 46 31 744 7701 358 9 4780 www zyxel fi 8411 358 9 4780 8448 REGULAR MAIL ZyXEL Communications A S Columbusvej 5 2860 Soeborg Denmark ZyXEL Communications A S Nils Hansens vei 13 0667 Oslo Norway ZyXEL Communications A S Sj porten 4 41764 G teborg Sweden ZyXEL Communications Oy Malminkaari 10 00700 Helsinki Finland BPS 120 User s Guide Table of Contents 1 Introducing the BPS 120 aianei naen ar tetaaaattetaananaeaaasonoesssasonoesaasonne
Download Pdf Manuals
Related Search