ZyXEL ADSL2+ User's Manual
Contents
1. s IP address see Section 4 1 on page 9 Ping the Prestige from a computer on the LAN Make sure your computer s Ethernet adapter is installed and functioning properly In the computer click Start All Programs Accessories and then Command Prompt In the Command Prompt window type ping followed by the Prestige s LAN IP address 192 168 1 1 is the default and then press ENTER The Prestige should reply otherwise see Section 4 1 on page 9 If the Prestige s IP address has changed then enter the new one as the URL Use Internet Explorer 6 0 and later or Netscape Navigator 7 0 and later with JavaScript enabled Make sure you enter the password correctly the field is case sensitive If you ve forgotten the Prestige s password use the RESET button Press the button in for about 10 seconds or until the PWR SYS LED starts to blink then release it It returns the Prestige to the factory defaults password is 1234 LAN IP address 192 168 1 1 etc see your User s Guide for details Verify the Internet connection settings in the wizard Make sure you entered the correct user name and password if you are using PPPoE or PPPoA The Prestige stores the Internet connection settings that it detects using zero configuration Reset the Prestige to the factory defaults or manually configure it for Internet access if you connect it to another DSL line with a different VPI and VCI 4 1 Set Up Your Computer s IP Address T2. IP address to multiple private IP addresses on your LAN SUA Only You must select Routing mode to use routing features such as NAT Click NAT Mode If you have NAT Edit SUA NAT Server Set Advanced servers on your Network Address Translation i Start Port No End Port No IP Address Setup and LAN configure All ports j All ports booo then NAT an SUA server p pono to open the ae set to have NAT Mode M Enable SIP ALG them visible to b P fron screen the outside a b ooo Select From the NAT a SUA Only Mode screen bt ft kore i i fo 0 00 if you have one public IP address and Full click Edit Feature if you have multiple public IP addresses Details and fill m 7 lin A for address translation in the fields as shown _Reset 4 Troubleshooting None of the LEDs turn on Make sure that you have the correct power adaptor connected to the Prestige it is when you connect the Prestige s power Cannot access the Prestige from my computer Cannot access the Internet plugged into an appropriate power source and the Prestige is turned on Check all cable connections If the LEDs still do not turn on you may have a hardware problem In this case you should contact your local vendor Check the cable connection from your computer to the Prestige Make sure your computer s IP address is in the same subnet as the Prestige
3. Certifications 1 Go to www zyxel com 2 Select your product from the drop down list box on the ZyXEL home page to go to that product s page 3 Select the certification you wish to view from this page 10
4. P 660H D Series ADSL2 4 port Gateway Quick Start Guide Version 3 40 10 2005 ZyXEL P 660H D Series Quick Start Guide Overview The Prestige 660H D P 660H D ADSL 2 4 port gateway is the ideal device for small networks connecting to the Internet via ADSL See your User s Guide for background information on all features 1 Hardware Connections If you prefer to see a multi media animation of how to make hardware connections see the included CD 4 3 2 1 ON RADSL L BE WAN 10 100m __ _1_ RESET POWER gy OFF 1 DSL Connect the Prestige to a telephone jack using a telephone wire 2 LAN 10 100M Use an Ethernet cable to connect a computer to the LAN port for initial configuration and or Internet access 3 POWER Use the included power adaptor to connect the POWER socket to an appropriate power source see the User s Guide for power adaptors specifications by region After you ve made the connections push in the power button to turn on the Prestige Look at the front panel LEDs The PWR SYS LED blinks while performing system testing The PWR SYS LED then turns steady on if the testing is successful The LAN LED turns on if the LAN port is properly connected 2 Configuration for Internet Access You may configure the Prestige for Internet access in any one of these ways e Zero Configuration P 660H D Series Quick Start Guide e Web Configurator Internet Access Wizard Not
5. e Zero configuration is only able to configure the device automatically for Internet access if you are using PPPoE PPPoA or ENET ENCAP encapsulation with a dynamically assigned IP address from your ISP If you re not using these Internet access settings then use the Web Configurator Internet Access Wizard to manually configure the device You will need your Internet access information such as user name and password if given by your ISP INFORMATION From ISP ENCAPSULATION METHOD YOU ARE USING None RFC1483 in bridge mode with a dynamic IP address or ENET ENCAP with a dynamic IP address An IP address only RFC1483 in routing mode with a static IP address A user name and password and an IP address PPPoA or PPPoE encapsulation with a static IP address An IP address subnet mask and a gateway IP ENET ENCAP with a static IP address address 2 1 Zero Configuration Launch your web browser and navigate to any web site for example www zyxel com The Prestige automatically detects and configures your Internet 4d EE connection This may take about two minutes Aadress j http www zyxel com If you have a PPPoE or PPPOA connection a screen displays prompting you to enter your Internet account information Enter the username password and or service name exactly as provided Your router has established a DSL connection to your local exchange To log on to the Internet Click Log on to the Internet the rout
6. e wizard screen A Select Active to have the Prestige control the A bandwidth allocated to traffic going out through the Prestige s WAN or LAN port Media Bandwidth Management Select the service to apply bandwidth management B Select the services for which you want to al manage bandwidth Crp C Click Next T E Mail l eMule P 660H D Series Quick Start Guide 2 The Prestige automatically creates the bandwidth class for each service you select A Select High Mid or Low priority to control the Media Bandwidth Management Set bandwidth priorities for the services fisted distribution of bandwidth to selected services Service Priority bya XBox Live High Mid Low Others A service with High priority is given as much VoIP SIP G High Mid C Low Others bandwidth as it needs If you select services as having the same Back _Finish priority then bandwidth is divided equally amongst those services Services not specified in bandwidth management are allocated bandwidth after all specified services receive their bandwidth requirements If the rules set up in this wizard are changed in the advanced setup then the service priority will be set to Others B Click Finish 3 NAT NAT Network Address Translation NAT RFC 1631 means the translation of an IP address in one network to a different IP address in another For example you could translate one public
7. eout field F If you selected Routing select SUA Only when you have one public IP address Full Feature when you have more than one public IP address for translation or None to disable NAT G Click Next 2 Verify your LAN and WAN settings and click Save Settings 3 The Prestige automatically tests the connection to the computer s connected to the LAN port To test the connection from the Prestige to the ISP click Start Diagnose Otherwise click Return to Main Menu to go back to the main screen Wizard Setup ISP Parameters for internet Access WAN Information Mode Routing Encapsulation PPPoE Multiplexing LLC YPIVCI 8 35 Service Name User Name user domain RERRRARK IP Address Obtain an IP Address Automatically Network Address Translation SUA Only Connection Nailed Up Connection Wizard Setup ISP Parameters for Internet Access LAN Information IP Address 192 168 1 1 IP Mask 255 255 255 0 DHCP ON Client IP Pool Starting Address 192 168 1 33 Size of Client IP Pool 32 Change LAN Configuration Save Settings LAN connections Test your Ethernet Connection PASS WAN connections Test ADSL synchronization PASS Test ADSL ATM OAM loopback test PASS Test PPP PPPoE server connection Pass Ping default gateway Pass Return to Main Menu 2 2 3 Media Bandwidth Management 1 Click Media Bandwidth Mgnt in the Site Map screen to open th
8. er needs the Internet user name and password provided by your ISP Back gt amp DSL Connection Successful Enter your details below and click the Log On button Instructions Router Password User Name Password Log on to the Internet Log on failed most likely because one or more of the details you entered above was incorrect You can try re entering the details now But if you continue to fail call your ISP for support and to check your account is active P 660H D Series Quick Start Guide 2 2 Web Configurator Internet Access Wizard 2 2 1 Accessing the Web Configurator 1 Launch your web browser Enter 192 168 1 1 as the web site address g Back fe at A Sear Address Fy http 192 168 1 1 Note If you do not see the next screens then please read Section 4 1 on page 9 2 Click Login 3 Type a new password retype it to confirm and click Apply Otherwise click Ignore You then see the main web configurator screen 4 In the Site Map screen click Wizard Setup P 660H D1 Enter Password and click Login Use this screen to change the password We recommend that you personalize the system administrator _ password by changing it to something besides the default 1234 Password E The administrator password should must be between 1 30 Losin Cancel characters New Password Retype to Confirm Ignore ZyXEL TOTAL INTERNET ACCESS SOLUTION W
9. his section shows you how to set your Windows NT 2000 XP computer to automatically get an IP address This ensures that your computer can connect with your Prestige Refer to your User s Guide for detailed IP address configuration for other Windows and Macintosh computer operating systems 1 In Windows XP click start Control Panel In Windows 2000 NT click Start Settings Control Panel 2 In Windows XP click Network Connections In Windows 2000 NT click Network and Dial up Connections 3 Right click Local Area Connection and then click Properties P 660H D Series Quick Start Guide 4 Select Internet Protocol TCP IP under the General tab in FD Danan Windows XP and click Properties Goal Ros enera emate Lonfiguration 5 The Internet Protocol TCP IP Properties screen opens the General tab in Windows XP You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings 6 Select the Obtain an IP address automatically and Obtain DNS server address automatically options Use the following IP address 7 Click OK to close the Internet Protocol TCP IP Properties window 8 Click Close OK in Windows 2000 NT to close the Local Area Connection Properties window Obtain DNS server address automatically Use the following DNS server addresses 9 Close the Network Connections screen Viewing Your Product s
10. ing then ENET ENCAP B Click Next C If your ISP gave you an IP address subnet mask and gateway address select Static IP address and enter them Otherwise select Obtain an IP Address Wizard Setup ISP Parameters for internet Access Mode Routing Encapsulation Q ENET ENCAP gt Wizard Setup ISP Parameters for Internet Access Multiplex LLC Virtual Circuit ID IP Address VPI eS CG Obtain an IP Address Automtically YCI 5 Static IP Address IP Address 0 0 0 Subnet Mask co i Automatically ENET ENCAP Gateway D Select SUA Only if you have one public IP address ia cn E Full Feature if you have more than one public IP E address for translation or None to disable NAT E Click Next A Select Routing then PPPoE B Click Next C Enter the service name username and password given by your ISP D If your ISP gave you an IP address select Static IP address and enter it Otherwise select Obtain an IP Address Automatically E Select Nailed Up Connection to have your connection up all the time Otherwise select Connect on Demand and specify an idle time out period in P 660H D Series Quick Start Guide Wizard Setup ISP Parameters for internet Access Routing gt Mode Encapsulation Multiplex Virtual Circuit ID VPI VCI seconds in the Max Idle Timeout field F Select SUA Only if you have one public IP add
11. izard Setup Advanced Setup Maintenance rE Wizar d Sei Password System Status eee ee Media Bandwidth Mgnt LAN DHCP Table WAN Any IP Tabie Maintenance NAT Diagnostic ER a Dynamic ONS Finnware z Tine and Date Logout Arewall Content Filter Remote Management UPnP Logs Meda Bandwidih Mant P 660H D Series Quick Start Guide 2 2 2 Internet Access Setup 1 Configure the Internet access settings in this step The wizard screens vary depending on the Mode and Encapsulation you chose in the first wizard screen Note Enter the Internet access information given to you by your ISP exactly in each wizard screen If not given leave the fields set to the default A Select Routing if your ISP gave you an IP address and allows multiple computers to share an Internet account Otherwise select Bridge Then select RFC 1483 B Click Next Wizard Setup ISP Parameters for Internet Access Mode Routing gt Encapsulation RFC1483 x Multiplex LLC Virtual Circuit ID Wizard Setup ISP Parameters for internet Access C If you selected Routing enter the VPI B IP address given by your ISP vel Bs eee 0 0 00 D If you selected Routing select Network Address Translation SUA Only when you have one SUA Ony z public IP address Full Feature when you have more than one public IP address for translation or None to disable NAT E Click Next ENET ENCAP A Select Rout
12. ress Full Feature if you have more than one public IP address for translation or None to disable NAT G Click Next A Select Routing if your ISP allows multiple computers to share an Internet account Otherwise select Bridge Then select PPPOA B Click Next C Enter the username and password given by your ISP D If your ISP gave you an IP address select Static IP address and enter it Otherwise select Obtain an IP Address Automatically E Select Nailed Up Connection to have your connection up all the time Wizard Setup ISP Parameters for Internet Access Routing PPPoA gt Mode Encapsulation Multiplex Virtual Circuit ID Wizard Setup ISP Parameters for Internet Access a Service Name User Name Password IP Address Obtain an IP Address Automatically Static IP Address Connection O C Connect on Demand Max Idle Timeout sec Nailed Up Connection Network Address Translation SUA Only gt Wizard Setup ISP Parameters for Internet Access fuser O User Name Password IP Address Connection Obtain an IP Address Automatically C Static IP Address O C Connect on Demand Max Idle Timeout sec Nailed Up Connection Network Address Translation SUA Only Q P 660H D Series Quick Start Guide Otherwise select Connect on Demand and specify an idle time out period in seconds in the Max Idle Tim
Download Pdf Manuals
Related Search