Zurn Z86300 User's Manual
Contents
1. HANDICAP OFFSET GRID DRAIN GH INSTALL POP UP OR GRID STRAINER IN SINK OUTLET AND PLUMB WASTE CONNECTION 7 TURN SUPPLY WATER ON AND OPERATE THE FAUCET WHILE CHECKING FOR LEAKS 8 INSTALL AERATOR 6 INTO FAUCET AND HAND TIGHTEN 9 METERING CARTRIDGE IS FACTORY PRESET FORA10 SECOND CYCLE AT 80 PSI IF ADJUSTMENT IS NECESSARY SEE ADJUSTING THE FLOW SECTION PAGE 2 PAGE 1 OF 4 Form CF848 Date 6 19 07 C N No 105794 Rev G MAINTENANCE 1 YOUR ZURN AQUASPEC FAUCET HAS AHIGHLY POLISHED NICKEL CHROME PLATED FINISH CLEAN WITH SOAP AND WATER ORAMILD CLEANER WHICH IS SAFE FOR CHROME PLATING DO NOT USE ACIDS OR TOILET BOWL CLEANER AS THEY WILL DAMAGE THE FINISH 2 METERING CARTRIDGE 3 REMOVALAND REPLACEMENT 2 1 REMOVE COLORED INDEX BUTTON 1C FROM HANDLE 1A 2 2 LOOSEN SET SCREW 1B IN HANDLE WITH 3 32 ALLEN WRENCH 2 3 PULLUP ON HANDLE TO REMOVE FROM STEM 2C OF HANDLE NUT ASSEMBLY 2 2 4 REMOVE HANDLE NUT ASSEMBLY 2 USING 1 1 8 HEX 6 POINT SOCKET 2 5 REMOVE METERING CARTRIDGE 3 BY LIFTING OUT OF FAUCET BODY 4 IT MAY BE NECESSARY TO OPEN THE SUPPLY STOP SLIGHTLY TO ALLOW WATER PRESSURE TO PUSH THE METERING CARTRIDGE UPWARD 2 6 INSPECT METERING CARTRIDGE 3 FOR WORN PARTS DAMAGED PARTS AND ANY CONTAMINATION THAT MAY BE PREVENTING THE METERING CARTRIDGE FROM MOVING FREELY OR SEATING OTHER THAN CLEANING ANY TRAPPED DEBRIS THERE ARE NO SERVICEABLE PARTS IN THE METERING CARTRID2. i Remove handle using 3 32 Allen wrench Rotate timing adjustment nut up CCW to shorten handle stroke and decrease cycle time Metering cartridge is overly contaminated or damaged Replace metering cartridge G61754 per Installation and Maintenance guide Ensure filter assembly with flow control orifice is installed Shut off water supply Remove filter assembly to clean and or replace Filter may be located externally on sup ply stops or internally within faucet body under metering cartridge Reference parts list included with faucet for filter style Water hammer due to pressure and piping Faucet is making configuration noise at shutoff Gradually back off flow rate on supply stops to reduce pressure at metering cartridge until noise has been elimi nated Excessively high water pressure gt 80 psi Handles becoming loose Loosen set screw in handle with 1 8 Allen wrench While Handle not seated properly when inst llsd pressing down on handle to seat on handle nut stem retighten set screw in handle with normal usage PAGE 4 OF 4 Form CF848 Date 6 19 07 C N No 105794 Rev G
3. AQUASPEG FAUCETS MODEL Z86300 SERIES s Fa R l SINGLE BASIN METERING ZURN e TECHNICAL INFORMATION FLOW 0 25 GPC MAXIMUM PRESET AT FACTORY TO 10 SECOND 80 PSI ADJUSTABLE MAXIMUM PRESSURE 125 PSI MAXIMUM TEMPERATURE 1802 F CAN USE QUARTER TURN CERAMIC DISK CARTRIDGE IMPORTANT THE WATER SUPPLY LINES MUST BE THOROUGHLY FLUSHED BEFORE INSTALLATION TO PREVENT FOREIGN MATTER AND DEBRIS FROM CLOGGING AND OR DAMAGING INTERNAL COMPONENTS AND THEREBY PREVENTING THE FAUCET FROM FUNCTIONING PROPERLY IMPORTANT THE FAUCET HAS AN INTEGRAL SHANK FILTER ASSEMBLY INSTALLED IN THE BODY UNDER THE METERING CARTRIDGE TO PREVENT FOREIGN MATTER AND DEBRIS FROM DAMAGING THE FAUCET THE INTEGRAL FILTER MAY BE REMOVED TO BE BACK FLUSHED AND CLEANED IF INSUFFICIENT FLOW IS DETECTED THE INTEGRAL SHANK FILTER ASSEMBLY MUST BE RE INSTALLED AFTER SERVICING TO ENSURE PROPER FUNCTIONING OF THE METERING CARTRIDGE gt INSTALLATION INSTRUCTIONS 1 THE WATER SUPPLY LINE MUST BE THOROUGHLY FLUSHED BEFORE FAUCET INSTALLATION 2 REMOVE FAUCET BODY FROM CARTONAND PLACE GASKET 7A ON SHANK 3 PLACE FAUCET ON SINK MOUNT LOCKWASHER 7B AND MOUNTING NUT 7C ONTO SHANK FROM UNDER SINK 4 HAND TIGHTEN MOUNTING NUT 7C MAKE SURE FAUCET IS CENTERED PROPERLY DO NOT OVER TIGHTEN YOU COULD DAMAGE THE FIXTURE 5 ATTACH LAVATORY SUPPLY TO THE OUTLET OF THE STOP BODY AND CONNECT TO FAUCET WITH RISER NUT 7D 6 OPTIONAL POP UP P GRID STRAINER G
4. D WIDE WEB www zurn com gt Installation Instructions are revised frequently Please access website for the latest revision PAGE2OF4 Form CF848 Date 6 19 07 C N No 105794 Rev G Z86300 PICTURED ITEM PART DESCRIPTION QTY TEM PART DESCRIPTION QTY 1 G60522 METERING HANDLE ASSEMBLY 1 3 G61754 METERING CARTRIDGEASS Y 1 1A 60601003 COLD METERING HANDLE 1 3A 58155020 O RING 1 1B 62705001 SET SCREW 1 3B 81241001 WASHER 1 1C G60558 METERING INDEX BUTTONS H C 1 4 G67787 INTEGRAL SHANK FILTER 1 60460001 HOT INDEX 1 5 61483004 SINGLE WATER BODY 1 60460002 COLD INDEX 1 6 G63561 13 16 27 MALE SPRAY OUTLET 1 0 GPM 25 GPC 1 60460003 TEMPERED INDEX f 7 G63367 MOUNTING HARDWARE 1 2 G60561 HANDLE NUTASSEMBLY 1 7A 60549001 GASKET 1 2A 60465001 E RING 1 7B 61613019 LOCKWASHER i 2B 60450001 SPRING SEAT 1 7C 59530002 MOUNTING NUT 1 2C 60451003 STEM 1 7D 59532001 1 2 NPSM RISER NUT 1 2D 60447001 SPRING 1 2E 60446001 ADJUSTMENT NUT 1 2F 60452001 CAP 1 2G 60456001 STEM HOUSING 1 2H 62499107 O RING 1 2l 60458001 O RING RETAINER 1 PAGE 3 OF 4 Form CF848 Date 6 19 07 C N No 105794 Rev G Metering Faucet Trouble Shooting Guide Problem Cause Solution Open supply stops Filter assembly Shut off water supply Remove filter assembly contaminated to clean and or replace Filter may be located ex
5. GE CONTAMINATED OR DAMAGED METERING CARTRIDGE ASSEMBLIES SHOULD BE REPLACED 2 7 REVERSE STEPS 2 1 THROUGH 2 5 FOR RE ASSEMBLY TIGHTEN CAP 2G WITH 1 1 8 HEX 6 POINT SOCKET UNTIL NO WATER IS LEAKING FROM UNDER THE HANDLE NUT ASSEMBLY WHEN THE FAUCET IS RUNNING HOLD DOWN HANDLE 1 WHILE TIGHTENING SET SCREW 1B TO ENSURE PROPER SEATING 3 IT MAY BE NECESSARY TO REPLACE OR BACK FLUSH THE INTEGRAL SHANK FILTER CARTRIDGE AND AERATOR PERIODICALLY TO REMOVE COLLECTED SEDIMENT AND DEBRIS 3 1 THE INTEGRAL SHANK FILTER 4 MAY BE REMOVED BY USING A 1 4 ALLEN WRENCH CLEAN OR REPLACE AS REQUIRED ADJUSTING THE FLOW ON ZURN METERING FAUCET 1 METERING FAUCETS ARE FACTORY PRESET FOR A 10 SEC CYCLE AT 80 PSI 2 ACTUATE FAUCET 3 TO 5 TIMES TO REMOVE ANY TRAPPED AIR IN THE SUPPLY LINE OR FAUCET 3 REMOVE HANDLE 1 PER INSTRUCTIONS IN MAINTENANCE SECTION 2 1 THROUGH 2 3 TO EXPOSE ADJUSTMENT NUT 2F 4 INCREASE CYCLE TIME BY TIGHTENING ADJUSTMENT NUT 2F 1 2 TURN CLOCKWISE DECREASE CYCLE TIME BY LOOSENING ADJUSTMENT NUT 1 2 TURN COUNTERCLOCKWISE CHECK FOR DESIRED CYCLE TIME BY ACTUATING FAUCET WITH HANDLE 1 IN PLACE ON STEM 2C REPLACEMENT PARTS HANDLE NUT ASSEMBLY G60561 METERING CARTRIDGE ASSEMBLY G61754 HANDLE ASSEMBLY G60522 INTEGRAL SHANK FILTER ASSEMBLY G67787 n ZURNINDUSTRIES INC COMMERCIALBRASS OPERATIONS 2 URN 2640 SOUTH WORK STREET FALCONER N Y 14733 Ze PHONE 1 716 665 1132 FAX 1 716 665 1135 WORL
6. ternally on supply stops or internally within faucet body under metering cartridge Reference parts list included with fauet for filter style No water dispensing from faucet Timing nut requires Remove handle using 3 32 Allen wrench Rotate timing adjustment nut down CW to lengthen handle stroke and increase cycle time Damaged Schrader valve Replace metering cartridge G61754 per Installation and stem in center of Maintenance guide metering cartridge Faucet is shutting off to quickly Metering cartridge is overly Replace metering cartridge G61754 per Installation and contaminated or damaged Maintenance guide Timing nut requires Remove handle using 3 32 Allen wrench Rotate timing adjustment nut up CCW to shorten handle stroke and decrease cycle time Faucet is running iso lond Aerator is not installed or Install 1 0 GPM or 0 5 GPM aerartor Cycle time may be incorrect aerator installed too long with aerator s gt 1 0 GPM Metering cartridge is overly Replace metering cartridge G61754 per Installation and contaminated or damaged Maintenance guide Install 1 0 GPM or 0 5 GPM aerator Facuet may not shut Aerator is not installed off with aerator s gt 1 0 GPM or incorrect aerator installed Tighten handle nut using 1 1 8 hex 6 point socket to create seal and seat metering cartridge Do not over tighten Handle nut is not Faucet wae adequately tightened shut off Timing nut requires
Download Pdf Manuals
Related Search