Zanussi ZWF 16281 W User's Manual
Contents
1. The selected delay can be changed only after selecting the washing programme again The door will be locked throughout the delay time If you need to open the door you must first set the washing machine to PAUSE by pressing the Start P ause button and then wait about 2 minutes untill the Door light has gone off After you have closed the door press the Start P ause button again The Delay Start cannot be selected with Drain programme Operating sequence 10 Programme progress display After having depress Start P ause button the Wash pilot light illuminates and stays on while the machine is working O wash Door Q End The Door pilot light indicates if the door can be opened ight on the door cannot be opened The appliance is in function light off the door can be opened The washing programme is finished flashing light the door is opening When the programme has finished the End pilot light illuminates and the Wash light goes off Altering an option or a running programme Itis possible to change any option before the programme carries it out Before you make any change you must pause the washing machine by pressing the Start Pause button ZANUSSI R Electrolux Changing a running programme is possible only by resetting it Turn the programme selector dial to Off and then to the new programme position The washing water in the tub will not emptied out Start the ne2. Close the drawer gently 3 Select the required programme The selector dial is divided into the following sections e Cottons e Synthetics e Delicates e Special The green Start P ause light starts to flash The selector dial can be turned either clockwise or anticlockwise ZANUSSI H Electrolux Position Off to Reset programme S witching OFF of the machine At the end of the programme the selector dial must be turned to position Off to switch the machine off IMPORTANT If you turn the programme selector dial to another programme when the machine is working the red Start P ause pilot light will flash 3 times and the message Err is displayed on the display to indicate a wrong selection The machine will not perform the new selected programme 4 Select the spin speed or Night Cycle or Rinse Hold option 1600 900 700 oo Ou Spin Press the Spin button repeatedly to change the Spin speed if you want your laundry to be spun at a speed different from the one proposed by the appliance The relevant light will light up Maximum speeds are e Cottons 1600 rpm e Synthetics Wool Wandwash Sport Shoes 40 and Sport 40 900 rpm e Delicates Mini 30 and Silk 700 rpm Night Cycle by selecting this option the machine will not drain the water of the last rinse so as not to crease the laundry As all Spinning phases are suppressed this washing cycle is very noiseles
3. button again If you have chosen a delayed start the machine will begin the countdown IMPORTANT If an incorrect option is selected the red pilot light of the Start Pause button flashes for 3 times and the message Err is displayed for about 2 seconds 9 Select the Delay Start desired delay Delay Start i Before you start the Ca programme if you wish to delay the start press mm the Delay Start button repeatedly to select the KA CZ Y 16 The selected delay time value up to 20 hours will appear on the display for about 3 seconds then the duration of the programme will appear again You must select this option after you have set the programme and before you press the Start P ause button Selecting the delayed start e Select the programme and the required options e Select the delay start e Depress Start Pause button the machine Starts its hourly countdown The programme will start after the selected delay has expired Cancelling the delayed start You can cancel the delay time at any moment before you press the Start P ause button If you have already pressed the Start P ause button and you wish to cancel the delay time proceed as follows e set the washing machine to PAUSE by pressing the Start P ause button press the Delay Start button more times until the symbol is displayed press the Start P ause button again to start the programme IMPORTANT
4. e Screw the pump cover fully in e Close the pump door IMPORTANT When the appliance is in use and depending on the programme selected there can be hot water in the pump Never remove the pump cover during a wash Cycle always wait until the appliance has finished the cycle and is empty When replacing the cover ensure it is securely retightened so as to stop leaks and young children being able to remove it Cleaning the water inlet filter If your water is very hard or contains traces of lime deposit the water inlet filter may become clogged Itis therefore a good idea to clean it from time to time Turn off the water tap Unscrew the water inlet hose Clean the filter using a hard bristle brush Tighten up the inlet hose 20 The dangers of freezing If the machine is exposed to temperatures below 0 C certain precautions should be taken e Turn off the water tap e Unscrew the inlet hose e Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out e Screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again e When you intend to start the machine up again make sure that the room temperature is above 0 C IMPORTANT Every time you drain the water through the emergency emptying hose you must pour 2 litres of water into the main wash compartment of the detergent drawer and th
5. max and woollens e liquid detergents preferably for low temperature wash programmes 60 C max for all types of fabric or special for woollens only The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash programme If using concentrated powder or liquid detergents a programme without prewash must be selected The washing machine incorporates a recirculation system which allows an optimal use ofthe concentrated detergent Pour liquid detergent into the dispenser drawer compartment marked LIU just before starting the programme Any fabric softener or starching additives must be poured into the compartment marked db before starting the wash programme Follow the product manufacturer s recommendations on quantities to use and do not exceed the MAX mark in the detergent dispenser drawer 11 Quantity of detergent to be used The type and quantity of detergent will depend on the type of fabric load size degree of soiling and hardness of the water used Water hardness is classified in so called degrees of hardness Information on hardness of the water in your area can be obtained from the relevant water supply company or from your local authority Follow the product manufacturers instructions on quantities to use Degrees of water hardness Follow the product manufacturers instructions on quantities to use Before the
6. Customer Care Department by letter or telephone at the address below or visit our Website at www electrolux co uk Customer Care Department Electrolux Major Appliances Addington Way Luton Bedfordshire LU4 9QQ Tel 08705 727 727 Calls may be recorded for training purposes 31 For Customer Service in The Republic of Ireland please contact us at the address below Electrolux Group Irl Ltd Long Mile Road Dublin 12 Republic of Ireland Tel 353 0 1 4090751 Email service eid electrolux ie European guarantee This appliance is guaranteed by Electrolux in each of the countries listed in the following page for the period specified in the appliance guarantee or otherwise by law If you move from one of these countries to another of these countries the appliance guarantee will move with you subject to the following qualifications e The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of a valid purchase document issued by seller of the appliance e The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your country of residence for this particular model or range of appliances e The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to another user e The appliance is installed and used in accordance with instructions issued by Electrolux and is only
7. Service Centre will require this information 23 Technical data Dimensions Electrical connection Voltage Overall power Fuse Water supply pressure Maximum Load Spin Speed Width 60 cm Height 85 cm Depth inclunding the porthole 63 cm Information on the electrical connection is given on the rating plate on the inner edge of the appliance door Minimum 0 05 MPa Maximum 0 8 MPa Cotton 71 kg Synthetics 3 5 kg Delicates 35 kg Woollens and handwash 2 kg Maximum 1600 rpm E E ZANUSSI EP R Electrolux Consumption values Programme Programme Energy Water duration consumption consumption in minutes in kWh in litres Cottons 95 C Dail 65 Cottons 60 Eco f 1 19 57 Cottons 60 C 40 C g 14 62 Cottons 40 Eco 5 1635 57 Synthetics 50 C 40 C i 0 85 57 Synthetics Easy Iron 40 C 0 45 63 Delicates 40 C 30 C i 0 6 63 Wool 40 C i 0 45 57 Handwash 30 C Cold i 0 3 55 Mini 30 0 3 55 Silk 30 C 0 25 53 Sport Shoes 40 C g 0 5 57 Sport 40 C 0 75 70 Rinse f 0 1 50 Drain Spin i i infos The consumption data shown on this chartis to The Cottons 60 Eco is the reference be considered purely indicative as it may vary programme with a load of 7 kg for the data depending on the quantity and type of laundry entered in the energy label in compliance on the inlet water temperature and on the with EEC 92 75 standards ambient temperature It refers to the hi
8. The machine performs some additional rinses Extra Rinse Operating sequence This option is recommended for people who are allergic to detergents and in areas where the water is very soft If you press this button simultaneously for about 6 seconds in combination with Options button the child safety lock will be enabled see Display paragraph 7 Display The display shows the following information Duration of the selected programme After selecting a programme the duration is displayed in hours and minutes for example 2 05 The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric SES SE 27 TT Delayed start The selected delay 20 hours max set by means of the relevant button appears on the display for about 3 seconds then the duration of the previously selected programme is displayed After the programme has started the time remaining is updated every minute Nef N The delay time value decreases by one unit TSH every hour and then 1 TY when 1 hours remain the time decreases every minute Incorrect option selection QO Z S If an option which is not compatible with the set wash programme is selected the message ZANUSSI R Electrolux Err is displayed for about 2 seconds and the integrated red Start Pause light start flashing Alarm codes In the event of operating problems some alarm codes can be d
9. fast coloureds only Grass soap lightly and treat with bleach whites and fast coloureds only Ball point pen and glue moisten with acetone lay the garment on a soft cloth and dab the stain Lipstick moisten with acetone as above then treat stains with methylated spirits Remove any residual marks from white fabrics with bleach Red wine soak in water and detergent rinse and treat with acetic or citric acid then rinse Treat any residual marks with bleach Ink depending on the type of ink moisten the fabric first with acetone then with acetic acid treat any residual marks on white fabrics with bleach and then rinse thoroughly Tar stains first treat with stain remover methylated spirits or benzine then rub with detergent paste do not use acetone on artificial silk Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the environment Although biodegradable detergents contain substances which in large quantities can upset the delicate balance of nature The choice of detergent will depend on the type of fabric delicates woollens cottons ZANUSSI R Electrolux etc the colour washing temperature and degree of soiling All commonly available washing machine detergents may be used in this appliance e powder detergents for all types of fabric e powder detergents for delicate fabrics 60 C
10. first use AN WARNING Ensure that the electrical and water connections comply with the installation instructions IMPORTANT Remove the polystyrene block and any material from the drum IMPORTANT Pour 2 litres of water into the main wash compartment LIU of the detergent drawer in order to activate the ECO valve Then run a cotton cycle at 95 C without any laundry in the machine to remove any manufacturing residue from the drum and tub Pour 1 2 a measure of detergent into the dispenser drawer and start the machine 12 Degrees Characteristic dH un 1 soft 0 7 0 15 2 medium 8 14 16 25 3 hard 15 21 26 37 4 very hard gt 21 gt 37 Use less detergent if e you are washing a small load e the laundry is lightly soiled e large amounts of foam form during washing Operating sequence 1 Load the laundry Open the door by carefully pulling the door handle outwards Place the laundry in the drum one item ata time shaking them out as much as possible Close the door 2 Measure out the detergent and the fabric softener Pull out the dispenser drawer until it stops Measure out the amount of detergent required pour it into the main wash compartment LIU and if you wish to carry out a programme with the prewash phase pour it into the compartment marked LU If required pour fabric softener into the compartment marked amp the amount used must not exceed the MAX mark in the drawer
11. Synthetics 50 40 Synthetics Easy iron 40 Delicates 40 30 Max load for Cottons Max load for Synthetics esserne 3 5 kg Max load for Delicates isss 3 5 kg White cotton heavy Soiled cotton items e g sheets tablecloths household linen towels White and fast coloured cotton normally soiled cotton items sheets household linen underwear Coloured cotton lightly soiled shirts blouses towels underwear Coloured cotton lightly soiled shirts blouses underwear Synthetic or mixed fabrics underwear coloured garments non Shrink shirts blouses Synthetic or mixed fabrics to be gentle washed and spun Delicate fabrics for example curtains 7 kg Spin red CJ main wash at 95 C Prewash Intensive 3 rinses Super Quick Long Spin Extra rinse Main wash at 60 C Spin red CJ NER Prewash Extra rinse Long spin Main wash at Spin red 9 C Medos Prewash Intensive 3 rinses S Quick Extra rinse Long spin Spin red LJ aed 2 Prewash Extra rinse Long spin Spin red W main wash at Prewash Intensive 2 40 Super Quick rinses Extra rinse SE a Spin red e UJ Main wash at 40 P h ick 4 rinses ote Super Quick Sid Intensive Extra rinse ec Wee Prewash Super Quick 3 rinses Intensive Extra Rinse Short spin Max load for Synthetics Easy Iron 1kg Programme table Programme Description of Programme for wool o Wool Pure new wool n
12. ZANUSSI R Electrolux 4 b d 4d b User manual ES PA A bh p d P b a Bs y b d N Washing Machine L AS J mM S p ZWF 16281 W Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances Please read this user manual carefully and keep it throughout the product life cycle as a reference document The user manual should be passed on to any future owner of the appliance The following symbols are used in this manual Important information concerning your personal safety and information on how to avoid damaging the appliance i General information and tips wy Environmental information Content Safety information 3 Description of the appliance 5 Detergent dispenser drawer 5 Control panel and functions 6 Programme table 7 Programme information 9 Washing Hints 10 Before the firstuse 12 Operating Sequence 13 Care and cleaning 18 Something not working 21 Technical data 24 Consumption values 25 Installation instruction 26 Environmental concerns 30 Guarantee conditions 31 Eu
13. achine to wash articles with whalebones material without hems or torn material ZANUSSI H Electrolux e Always unplug the appliance and turn off the water supply after use clean and maintenance e Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may Cause injury or serious malfunctioning Contact your local Service Centre Always insist on genuine spare parts Installation e This appliance is heavy Care should be taken when moving it e When unpacking the appliance check that it is not damaged If in doubt do not use it and contact the Service Centre e All packing and transit bolts must be removed before use Serious damage can occur to the product and to property if this is not adhered to See relevant section in the user manual e After having installed the appliance check that it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable e If the machine is situated on a carpeted floor please adjust the feet in order to allow air to circulate freely e Always be sure that there is no water leakage from hoses and their connections after the installation e f the appliance is installed in a location subject to frost please read the dangers of freezing chapter e Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person e Any elec
14. al to Off Now can a new programme be selected Washing hints Sorting the laundry Follow the wash code symbols on each garment label and the manufacturer s washing instructions Sort the laundry as follows whites coloureds synthetics delicates woollens Temperatures for normally soiled white cottons and linen e g tea cloths towels tablecloths sheets for normally soiled colour fast garments e g shirts night dresses pyjamas in linen cotton or synthetic fibres and for lightly soiled white cotton e g underwear 90 or 95 50 60 for delicate items e g net curtains mixed laundry including synthetic fibres and woollens bearing the label pure new wool machine washable non shrink 30 40 Cold Before loading the laundry Never wash whites and coloureds together Whites may lose their whiteness in the wash New coloured items may run in the first wash they should therefore be washed separately the first time Make sure that no metal objects are left in the laundry e g hair clips safety pins pins Button up pillowcases close zip fasteners hooks and poppers Tie any belts or long tapes Remove persistent stains before washing Rub particularly soiled areas with a special detergent or detergent paste Treat curtains with special care Remove hooks or tie them up in a bag or net 10 Maximum loads Recommended loads are indicated in the programme charts G
15. astic film polystyrene can be dangerous to children danger of suffocation Keep them out of children s reach e Keep all detergents in a safe place out of children s reach e Make sure that children or pets do not climb into the drum To avoid this the machine incorporates special feature To disable this device and restore the possibility of closing the door rotate the button anti clockwise until the groove is vertical To activate this device rotate the button without pressing it inside the door clockwise until the groove is horizontal If necessary use a coin ZANUSSI R Electrolux Description of the appliance H Detergent dispenser drawer B control panel El Door opening handle EJ Drain pump H Adjustable feet Control panel and functions Special Sport 40 Off 95 Cottons Sport Shoes 40 a p2 silk 60 e Mini 30 ay s 40 Eco Cold m m 40 Hand Synthetics Wash os 30 Wool ao lool e Spin a g Etasylron40 40 rain Rime 30 Delicates Delay Start T C Q700 O Prewash Q Wash oo Q Intensive O Door s End Ou Oik O Om Spin Options Extra Rinse Start Pause ZWF 16281 W H Programme selector dial and On Off switch E Spin reduction button KE Options button L Extra Rinse button H Display KJ Start Pause button Delay Start button E Programme progress display ii e The programme selector dial allows to sele
16. ct a programme and or to switch the machine on off It can be turned either clockwise or anticlockwise The light Start P ause starts to flash e Press the Spin button repeatedly to change the spin speed if you want your laundry to be spun at a speed different from the one proposed by the washing machine or to select the Night cycle and Rinse Hold The relevant light will light up e By means of the Options button you can select only one of the following option Prewash Intensive Super Quick see the relevant chapter Operating sequence e The relevant light will light up e By means of this button the machine performs some additional rinses e The display shows the following information duration of the selected programme delayed start incorrect option selection alarm codes heating phase and end of programme e The Start Pause button allows to start the selected programme the corresponding green pilot light stops flashing e This button interrupts also a programme which is running the corresponding green pilot light starts to flash e The wash programme can be delayed from 30 min 60 min 90 min 2 hours and then by 1 hour up to a maximum of 20 hours by means of this button e The different pilot lights illuminate depending on the running programme phase Programme table ZANUSSI Electrolux Programme Description of Cottons 95 Cottons 60 Eco Cottons 60 40 Cottons 40 Eco
17. de a few centimetres beyond the edges of the machine N WARNING The machine should NOT be placed on deep pile carpeting NOTE Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown In the interest of the environment Washing machines and dishwashers should be connected to the FOUL drainage system the water will then be taken to a sewage works for treatment before being discharged safely into a river It is essential that these appliances are not connected to the surface water drainage System as this water is discharged directly into a river or stream and may cause pollution If you require any further advice please contact your local water authority Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person ZAN WARNING This appliance must be earthed The manufacturer declines any liability should this safety measure not be observed Before switching on make sure the electricity Supply voltage is the same as that indicated on the appliance s rating plate IMPORTANT Information on the electrical connection is given on the rating plate on the inner edge of the appliance door The appliance is supplied with a 13amp plug fitted In the event of having to change the fuse in the plug sup
18. dry is not evenly distributed in the drum Redistribute the laundry Too much detergent or unsuitable detergent creates too much foam has been used Reduce the detergent quantity or use another one Check whether there are any leaks from one of the inlet hose fittings It is not always easy to see this as the water runs down the hose check to see if it is damp There is water on the floor Check the water inlet hose connection The inlet hose is damaged Change it with a new one The cap on the emergency emptying hose has not been replaced after cleaning the pump Putthe cap back on the emergency emptying and place the latter back in its seat Too little detergent or unsuitable detergent has been used Increase the detergent quantity or use another one Stubborn stains have not been treated prior to washing Use commercial products to treat the stubborn Unsatisfactory washing results stains The correct temperature was not selected Check if you have selected the correct temperature Excessive laundry load ntroduce into the drum less laundry 22 ZANUSSI R Electrolux The programme is still running Waitthe end of washing cycle The door lock has not been released The door will not open Wait about 2 minute There is water in the drum Select drain or spin programme to empty out the water The transit bolts and packing have not been removed Check the correct instal
19. en aan den Rijn Norge 47 81 5 30 222 Rislakkvn 2 0508 Oslo sterreich 43 18 66 400 Herziggasse 9 1230 Wien Polska 48 22 43 47 300 ul Kolejowa 5 7 Warsaw Portugal 35 12 14 40 39 39 Quinta da Fonte Edificio Gon alves Zarco 035 2774 518 Paco de Arcos Romania 40 21 451 20 30 Str Garii Progresului 2 54 040671 RO Schweiz Suisse Svizzera 41 62 88 99 111 Industriestrasse 10 CH 5506 Magenwil Slovenija 38 61 24 25 731 Traska 132 1000 Ljubljana Slovensko 421 2 43 33 43 22 Electrolux Slovakia sr Electrolux Dom ce spotrebi e SK Sebenniho 1 821 03 Bratislava Suomi www electrolux fi Sverige 46 0 771 76 76 76 Electrolux Service S t Goransgatan 143 105 45 Stockholm T rkiye 4902122931025 Tarlaba caddesi no 35 Taksim Istanbul Poccua 7 095 937 7837 129090 Mockea Onuwnuitckui npocnext 16 BL Onumnuk 33 R Electrolux www electrolux com www zanussi electrolux co uk 132973940 Subject to change without notice ZANUSSI H Electrolux CE
20. en run the drain programme This will activate the ECO VALVE device avoiding that part of the detergent remains unused at next washing Emergency emptying out If the water is not discharged proceed as follows to empty out the machine e pull out the plug from the power socket e Close the water tap e if necessary wait until the water has cooled down e open the pump door e place a bowl on the floor and place the end of the emergency emptying hose into the bowl Remove its cap The water should drain by gravity into the bowl When the bowl is full put the cap back on the hose Empty the bowl Repeat the procedure until water stops flowing out e Clean the pump if necessary as previously described e replace the emergency emptying hose in its seat after having plugged it e Screw the pump cover again and close the door ZANUSSI H Electrolux Something not working IMPORTANT Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Centre please carry out the checks listed below During machine operation it is possible that the red Start P ause pilot light flashes and one of the following alarm codes appears on the display to indicate that the machine is not working e 72 problem with the water supply e Ec problem with water draining e 48 door open Once the problem has been eliminated pres
21. eneral rules Cotton linen drum full but not too tightly packed Synthetics drum no more than half full Delicate fabrics and woollens drum no more than one third full Washing a maximum load makes the most efficient use of water and energy For heavily soiled laundry reduce the load size Laundry weights The following weights are indicative bathrobe 1200 g napkin 100 g quilt cover 700 g Sheet 500 g pillow case 200 g tablecloth 250 g towelling towel 200 g tea cloth 100 g night dress 200 g ladies briefs 100 g man s work shirt 600 g man s shirt 200 g man s pyjamas 500 g blouse 100 g men s underpants 100 g Removing stains Stubborn stains may not be removed by just water and detergent It is therefore advisable to treat them prior to washing Blood treat fresh stains with cold water For dried stains soak overnight in water with a special detergent then rub in the soap and water Oil based paint moisten with benzine stain remover lay the garment on a soft cloth and dab the stain treat several times Dried grease stains moisten with turpentine lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth Rust oxalic acid dissolved in hot water or a rust removing product used cold Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole Mould stains treat with bleach rinse well whites and
22. ghest temperature for each wash programme 25 Installation instruction Unpacking All transit bolts and packing must be removed before using the appliance You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again 1 After removing all the packaging carefully lay machine on it s back to remove the polystyrene base from the bottom 2 Remove the power supply cable and the draining hose from the hose holders on the rear of the appliance 3 With a suitable spanner unscrew and remove the central rear bolt A 4 Unscrew and remove the two large rear bolts B and the six smaller bolts C 26 5 Remove the bracket D refit the six smaller bolts C and slide out the relevant plastic Spacer E Open the from the drum and remove the polystyrene block fitted with the adhesive tape on the door seal Open the porthole take out the inlet hose from the drum and remove the polystyrene block fitted with the adhesive tape on the door seal 7 Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet Positioning Install the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Check that the machine does not touch the wall or other kitchen units Level the was
23. hing machine by raising or lowering the feet The feet may be tight to adjust as they incorporate a self locking nut but the machine MUST be level and stable If necessary check the setting with a spirit level Any necessary adjustment can be made with a Spanner Accurate levelling prevents vibration noise and displacement of the machine during operation Never place cardboard wood or similar materials under the machine to compensate for any unevenness in the floor Water inlet An inlet hose is supplied and can been found inside the machine drum Do not use the hose from your previous machine to connect to the water supply 1 Open the porthole and extract the inlet hose 2 Connect the hose with the angled connection to the machine Do not place the inlet hose downwards Angle the hose to the left or right depending on the position of your water tap 3 Set the hose correctly by loosening the ring nut After positioning the inlet hose be sure to tighten the ring nut again to prevent leaks 4 Connect the hose to a tap with a 3 4 thread Always use the hose supplied with the appliance The inlet hose must not be lengthened If it is too short and you do not wish to move the tap you will have to purchase a new longer hose specially designed for this type of use NOTE Installation should comply with local water authority and building regulations requirements ZANUSSI R Electr
24. isplayed for example E20 see paragraph Something not working Heating phase S74 During the washing t cycle the display shows a temperature icon to indicate that the aS appliance has started the heating phase of the water in the tub Child safety lock enabled This device permits you to leave the appliance unsupervised without having the worry that children might be injured by or cause damage to the appliance This function remains able also when the washing machine is not working There are two different ways to set this option e before pressing the Start Pause it will be impossible to start the machine e after pressing the Start P ause it will be impossible to change any other programme or option 15 Operating sequence To enable or disable this option press simultaneously for about 6 seconds Extra Rinse and Options buttons until the icon E appears or disappears on the display 8 Select the Start Pause To start the selected programme press the Start Pause button the corresponding green pilot light stops flashing The Wash and Door lights are alight to indicate that the appliance starts operating and the door is locked Wash Door O tna Start Pause To interrupt a programme which is running depress the Start Pause button the corresponding green pilot light starts to flash To restart the programme from the point at which it was interrupted press the Start P ause
25. lation of the appliance The support feet have not been adjusted The machine vibrates or is noisy Check the correct levelling of the appliance The laundry is not evenly distributed in the drum Redistribute the laundry Maybe there is very little laundry in the drum Load more laundry The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum The laundry is redistributed by reverse rotation of the drum This may happen several times before Spinning starts late or the machine the unbalance disappears and normal spinning can does not spin resume If after 10 minutes the laundry is still not evenly distributed in the drum the machine will not spin In this case redistribute the load manually and select the spin programme e Redistribute the laundry The machine is fitted with a type of motor which makes an unusual noise compared with other traditional motors This new motor ensures a softer start and more even distribution of the laundry in the drum when spinning as well as increased stability of the machine Machines based on modern technology operate very No water is visible in the drum economically using very litte water without affecting performance The machine makes an unusual noise If you are unable to identify or solve the problem contact our service centre Before telephoning make a note of the model serial number and purchase date of your machine the
26. ly washed and spun to avoid any creasing In this way ironing is easier Furthermore the machine will perform additional rinses With this programme it is possible to rinse and spin cotton garments which have been washed by hand The machine performs 3 rinses followed by a final spin at maximum Speed The spin speed can be reduced by depressing Spin button For MU BD e water d last rinse in programmes with the Rinse Hold or Night Cycle 8 option Turn first the programme selector dial to Off then select programme Drain and depress the Start Pause button Separate spin for hand washed gare and after programmes with Rinse Hold CJ or Night Cycle option Before selecting this programme the selector dial must be turned to Off You can choose the speed by means of the relevant button to adapt it to the fabrics to be spun With this programme it is possible to wash one pair of sport shoes or 2 pairs if they are small The shoes would be gently washed and spun Washing temperature 40 C Note Don t wash your sport shoes together with laundry This programme is suitable for washing heavily soiled sport items of synthetic fabrics The machine will add automatically a prewash phase before the main wash to eliminate mud stains Note We recommend you not to put the detergent into the compartent LI of the detergent drawer The spin speed is reduced to 900 rpm To reset a programme and to switch off the machine turn the selector di
27. not available for Wool Handwash Mini 30 and Silk The prewash ends with a 14 short spin in programmes for cotton synthetic fabrics and Sport 40 whereas in the programmes for delicate fabrics and and Sport Shoes 40 the water is only drained Intensive this option can be selected for heavily soiled laundry the washing intensity will be increased and the washing time will be prolonged by few minutes depending on the selected type of fabric This option can be selected with all cottons synthetics and delicate programmes except for Eco programmes Super Quick a very short cycle for slightly Soiled items that have been used or worn for a short time This option is not available with the Wool Handwash Mini 30 Silk Sport Shoes 40 Sport 40 and Eco programmes The max load recommended for cotton is 3 5 kg and for synthetic and delicate is 2 kg IMPORTANT If an option is chosen that is not allowed with the selected programme the red pilot light of the Start P ause button will flash 3 times The washing time will be reduced according to the type of fabric and the selected temperature If you press this button simultaneously for about 6 seconds in combination with E xtra Rinse button the child safety lock will be enabled see Display paragraph 6 Select the Extra Rinse option This button can be x selected with all programmes except the Mini 30 Silk Wool and Hand wash programmes
28. olux The appliance must be connected to a cold water supply A minimum water pressure of 0 05 MPa 0 5 bar is required for safe operation of the appliance If you cannot make the cold water connection direct from the rising mains you may be able to operate the appliance from your cold water storage system There should be a minimum distance of 5 02m 16 5 ft between the appliance s inlet and the bottom of the water storage tank Water drainage This appliance is designed to be permanently plumbed into your home s drainage system using one of the following methods 1 Into a drainage standpipe oU piece supplied Woo y a 38 mm 11 2 standpipe diameter es Firstly form a hook in the end of the drain hose using the U piece supplied Place the drain hose into your standpipe which should have an internal diameter of approximately 38mm thus ensuring there is an air break between the drain hose and standpipe When discharging into a standpipe ensure that the top of the standpipe is no more than 90 cm 35 4 and no less than 60 cm 23 6 above floor level 27 The drain hose may be extended to a maximum of 4 metres An additional drain hose and joining piece is available from your local Service Force Centre The joining piece must have an internal diamete
29. on f eu a gon 40 shrink machine Spin red S9 EROR coin washable label p A Main wash at Handwas Special programme for 30 Cold 30 Cold hand washing fabrics Spin red 9 LJ 3 rinses Short spin Mini 30 Short cycle for lightly ed ee at 30 C 30 soiled fabrics Short spin Silk Silk items to be gentle e UJ x ud Sos 30 washed and spun Short spin Sport Shortcydeforlpairof Spin Red 9 CT Modul at 40 C Shoes 40 sport shoes Prewash Extra rinse Short spin Prewash at 30 C Sport 40 Programme for heavily U Main wash at 40 C p soiled synthetics items R 3 rinses Extra rinse Short spin Separate rinse cycle for Rinse hand washed items of all SPiN rd OU inas fabric Extra rinse ong sem For emptying out the last rinse water in Drain programmes with the Draining of water Rinse Hold or Night Cycle option Separate spin for Spin TM Spin red Drain and long spin Max load for Wool Max load for Sport Shoes 40 1 pair Handwash Mini 30 sss 2kg 2 pairs if they are small Max load for Silk se lkg Max load for Sport 40 ses 2 5 kg 8 ZANUSSI R Electrolux Programme information Wool and Handwash Easy Iron Rinse Drain Spin Sport shoes 40 Sport 40 Off Cancelling Washing programme for machine washable wool as well as for hand washable woollens and delicate fabrics with the hand washing care symbol Selecting this programme the laundry is gent
30. plied a 13amp ASTA approved BS 1363 A fuse must be used Should the plug need to be replaced for any reason proceed as described below ZANUSSI Electrolux The wires in the mains lead are coloured in accordance with the following code Green and Yellow Earth BlU8 5 i iei necem ever es lene Neutral The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or CORD CLAMP coloured green and yellow The wire coloured blue must be connected to the terminal marked N or coloured black The wire coloured brown must be connected to the terminal marked L or coloured red Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath AN WARNING A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely Should the appliance power supply cable need to be replaced this must be carried out by our Service Force Centre The power supply cable must be easily accessible after installing the appliance Permanent connection In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply mains with a minimum gap of 3mm between the switch contacts and of a type Suitable for the
31. r of 18mm If your drain hose looks like this see below you do not require the U piece Just push the hose firmly into the standpipe 2 Onto a sink outlet spigot If the outlet spigot has not been used before remove any blanking plug that may be in place Push the drain hose onto the spigot and secure with a clip if required ensure a loop is formed in the drain hose see diagram to prevent waste from the sink entering the washing machine Important Before connecting the machine to new pipework or to pipework that has not been used for some time run off a reasonable amount of water to flush out any debris that may have collected in the pipes 28 Levelling Level the washing machine by raising or lowering the feet The feet may be tight to adjust as they incorporate a self locking nut but the machine MUST be level and stable Any necessary adjustment can be made with a spanner Accurate levelling prevents vibration noise and displacement of the machine during operation Some vibration is inevitable especially if mounted on a wooden floor Sprung wooden floors are particularly susceptible to vibration For advice consult a builder If possible always place the machine on a solid floor Special conditions If the floor is carpeted or covered with crumbly or soft material insert a rigid support base under the feet to prevent noise vibration or displacement The base should protru
32. required load in compliance with the current electrical regulations The switch must not break the yellow and green earth cable at any point 29 Environmental concerns Packaging materials n Ecological hints The materials marked with the symbol CO are To save water energy and to help protect the recyclable environment we recommend that you follow gt P E lt polyethylene these tips gt P S lt polystyrene e Normally soiled laundry may be washed gt P P lt polypropylene without prewashing in order to save This means that they can be recycled by detergent water and time the environment disposing of them properly in appropriate is protected too collection containers e The machine works more economically if it is Old machine fully loaded Use authorised disposal sites for your old e With adequate pre treatment stains and appliance Help to keep your country tidy limited soiling can be removed the laundry i can then be washed at a lower temperature The symbol X on the product or on its e Measure out detergent according to the packaging indicates that this product may not water hardness the degree of soiling and be treated as household waste Instead it shall the quantity of laundry being washed be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environmen
33. ropean guarantee 32 Safety information In the interest of your safety and to ensure the correct use before installing and first using the appliance read this user manual carefully including its hints and warnings To avoid unnecessary mistakes and accidents it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features Save these instructions and make sure that they remain with the appliance if it is moved or sold so that everyone using it through its life will be properly informed on appliance use and safety General safety e It is dangerous to alter the specifications or attempt to modify this product in any way e During high temperature wash programmes the door glass may get hot Do not touch it e Make sure that small pets do not climb into the drum To avoid this please check into the drum before using e Any objects such as coins safety pins nails Screws stones or any other hard sharp material can cause extensive damage and must not be placed into the machine e Only use the advised quantities of fabric Softener and detergent Damage to the fabric can ensue if you over fill Refer to the manufacturer s recommendations of quantities e Wash small items such as socks laces washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum e Do notuse your washing m
34. s and it can be selectionned at night or in times with a more economical power rate On Cotton Synthetic 13 Operating sequence Silk Sport Shoes 40 and Sport 40 programmes the rinses will be performed with more water When the programme has finished the Start Pause light goes off the Door and End pilot lights are alight the display shows a flashing zero 0 00 and the door is blocked to indicate that the water must be emptied out Rinse Hold by selecting this option the water of the last rinse is not emptied out to prevent the fabrics from creasing When the programme has finished the Start P ause and Wash lights are off the pilot lights Door and End are alight on the display appears a flashing zero 8 00 and the door is locked to indicate that the water must be emptied out To empty out the water 1 turn the programme selector dial to Off 2 select the Drain or Spin programme 3 reduce the spin speed if needed by means of the relevant button 4 depress Start P ause button 5 atthe end of programme only the pilot lights End comes on 5 Select Prewash Intensive Super Quick option O Prewash Press the Options button repeatedly to select only one of the available options The relevant light will light up Intensive O Super Quick Options Prewash select this option if you wish your aundry to be prewashed at 30 C before the main wash
35. s the Start P ause button to restart the programme If after all checks the problem persists contact your local Service Centre The door has not been closed EY Close firmly the door The plug is not properly inserted in the power socket Insert the plug into the power socket There is no power atthe socket Please check your domestic electrical installation The main fuse has blown The washing machine does notstart Replace the fuse The selector dial is not correctly positioned and the Start P ause button has not been depressed Please turn the selector dial and press the Start P ause button again The delay start has been selected If the laundry are to be washed immediately cancel the delay start The water tap is closed E12 Open the water tap The inlet hose is squashed or kinked E72 Check the inlet hose connection The filter in the inlet hose is blocked 72 Clean the water inlet hose filter The door is not properly closed 40 Close firmly the door The machine does not fill i i The end of the drain hose is too low is rete fills then empties Refer to relevant paragraph in water drainage section The drain hose is squashed or kinked ECC Check the drain hose connection The drain pump is clogged Ee The machine does not empty and or Clean the drain pump does not spin The option J or 8 has been selected Select the Drain or Spin programmes The laun
36. t and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 30 Guarantee conditions Standard guarantee conditions We Zanussi Electrolux undertake that if within12 months of the date of the purchase this Zanussi Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OFCHARGE for labour materials or carriage on condition that e The appliance has been correctly installedand used only on the electricity supply statedon the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us Electrolux Service Force Centre must undertake all service work under this guarantee Any appliance or defective part replaced Shall become the Company s property This guarantee is in addition to your statutoryand other legal rights Exclusions e Damage or calls resulting fromtransportation improper use or neglect thereplacement of any light bulbs or removableparts of glass or plastic Cos
37. the dispenser drawer The washing powder and additive dispenser drawer should be cleaned regularly To aid cleaning the top part of the additive compartment should be removed ZANUSSI H Electrolux Remove the drawer by pressing the catch downwards and by pulling it out Flush it out under a tap to remove any traces of accumulated powder Cleaning the drawer recess Having removed the drawer use a small brush to clean the recess ensuring that all washing powder residue is removed from the upper and lower part of the recess Replace the drawer and run the rinse programme without any clothes in the drum Cleaning the pump The pump should be inspected if e the machine does not empty and or spin e the machine makes an unusual noise during draining due to objects such as safety pins coins etc blocking the pump Proceed as follows e Disconnect the appliance e If necessary wait until the water has cooled down e Open the pump door e Place a containfer close to the pump to collect any spillage e Pull out the emergency emptying hose place it in the container and remove its cap e When no more water comes out unscrew the pump cover and remove it Always keep a rag nearby to dry up spillage of water when removing the cover 19 e Remove any objects from the pump impeller by rotating it e Putthe cap back on the emergency emptying hose and place the latter back in its seat
38. trical work required to install this appliance should be carried out by a qualified electrician or competent person Use e This appliance is designed for domestic use It must not be used for purposes other than those for which it was designed e Only wash fabrics which are designed to be machine washed Follow the instructions on each garment label e Do not overload the appliance See the relevant section in the user manual e Before washing ensure that all pockets are empty and buttons and zips are fastened Avoid washing frayed or torn articles and treat stains such as paint ink rust and grass before washing Underwired bras must NOT be machine washed e Garments which have been in contact with volatile petroleum products should not be machine washed If volatile cleaning fluids are used care should be taken to ensure that the fluid is removed from the garment before placing in the machine e Never pull the power supply cable to remove the plug from the socket always take hold of the plug itself e Never use the washing machine if the power supply cable the control panel the working surface or the base are damaged so that the inside of the washing machine is accessible Child safety e This washing machine is not intended for use by young children or infirm persons without supervision e Young children should be supervised to ensure that they do not play with the appliance e The packaging components e g pl
39. ts incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom Appliances found to be in use within acommercial environment plus those which are subject to rental agreements Products of Electrolux manufacturer that are not marketed by Electrolux ZANUSSI H Electrolux Service and Spare Parts In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your postcode area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you have read the details under the heading Something not working When you contact the Service Force Centre you will need to give the following details 1 Your name address and postcode 2 Your telephone number 3 Clear concise details of the fault 4 The model and Serial number of the appliance found on the rating plate 5 The purchase date Please note a valid purchase receipt or guarantee documentation is required for in guarantee service calls Customer Care For general enquiries concerning your Electrolux appliance or for further information on Electrolux products please contact our
40. used within the home i e is not used for commercial purposes e The appliance is installed in accordance with all relevant regulations in force within your new country of residence The provisions of this European Guarantee do not affect any of the rights granted to you by law 32 ZANUSSI H Electrolux www electrolux com ry El Albania 35 5 4 261 450 Rr Pjeter Bogdani Nr 7 Tirane Belgique Belgi Belgien 32 2 363 04 44 Bergensesteenweg 719 1502 Lembeek Ceska republika 420 2 61 12 61 12 Bud jovick 3 Praha 4 140 21 Danmark 45 70 11 74 00 Sj llandsgade 2 7000 Fredericia Deutschland 49 180 32 26 622 Muggenhofer Str 135 90429 Nurnberg Eesti 37 2 66 50 030 Mustam e tee 24 10621 Tallinn Espa a 34 902 11 63 88 Carretera M 300 Km 29 900 Alcal de Henares Madrid France www electrolux fr Great Britain 44 8705 929 929 Addington Way Luton Bedfordshire LU4 9QQ Hellas 4302310561970 4 Limnou Str 54627 Thessaloniki Hrvatska 38 51 63 23 338 Slavonska avenija 3 10000 Zagreb Ireland 4353 1 40 90 753 Longmile Road Dublin 12 Italia 39 0 434558500 C so Lino Zanussi 26 33080 Porcia PN Latvija 37 17 84 59 34 Kr Barona iela 130 2 LV 1012 Riga Lituania 370 5 27 80 609 Verkiu 2 9 09108 Vilnius Lithuania Luxembourg 35 2 42 43 13 01 Rue de Bitbourg 7 L 1273 Hamm Magyarorsz g 36 1 252 1773 H 1142 Budapest XIV Erzs bet kir lyn tja 87 Nederland 31 17 24 68 300 Vennootsweg 1 2404 CG Alph
41. w programme by depressing the Start P ause button again Interrupting a programme Depress the Start P ause button to interrupt a programme which is running the corresponding light starts to flash Depress the button again to restart the programme Cancelling a programme Turn the selector dial to Off to cancel a programme which is running Now you can select a new programme Opening the door after the programme has started First setthe machine to pause by pressing the Start P ause button If the Door light flashes and after 2 minutes goes off the door can be opened If the Door light does not flash this means that the machine is already heating that the water level is above the bottom edge of the door or that the drum is turning In this case the door can not be opened If you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to Off After about 2 minutes the door can be opened pay attention to the water level and temperature 17 At the end of the programme The machine stops automatically The Start Pause and wash lights go off the end phase light illuminates and on the display will appear a flashing 0 00 The door can be opened the Door light is off If the CJ Rinse hold or Night Cycle option has been selected the End and Door phase lights illuminate but the door remains locked to indicate that the
42. water must be emptied out before opening the door The display will show a flashing 0 00 To empty out the water please read the steps on the Rinse Hold option paragraph Turn the programme selector dial to Off to Switch the machine off Remove the laundry from the drum and carefully check that the drum is empty If you do not intend to carry out another wash close the water tap Leave the door open to prevent the formation of mildew and unpleasant smells 18 Care and cleaning IMPORTANT You must DISCONNECT the appliance from the electricity supply before you can carry out any cleaning or maintenance work Descaling The water we use normally contains lime It is a good idea to periodically use a water softening powder in the machine Do this separately from any laundry washing and according to the softening powder manufacturer s instructions This will help to prevent the formation of lime deposits Maintenance Wash With the use of low temperature washes it is possible to get a build up of residues inside the drum We recommend that a maintenance wash be performed on a regular basis To run a maintenance wash e The drum should be empty of laundry e Select the hottest cotton wash programme e Use a normal measure of detergent must be a powder with biological properties External cleaning Clean the exterior cabinet of the appliance with soap and water only and then dry thoroughly Cleaning
Download Pdf Manuals
Related Search