Zanussi ZT 617 Instruction Booklet
Contents
1. jM X Ir gt gt N Me i MH Y f d i Cutlery should be placed in the removable cutlery basket with the handles facing downwards If the handles protrude from the bottom of the basket obstructing the lower spray arm load the cutlery with the handles facing upward Mix spoons with the other cutlery to prevent them sticking together Teaspoons may be loaded into the special slots provided in the cutlery basket handle The cutlery basket is in two parts which can be separated to give greater loading flexibility To separate the two parts slide them hori zontally in opposite directions and pull them apart To re assemble reverse the proce dure The two rear rows of prongs on the lower basket can be easily lowered to al low you to load pots pans and bowls To lower the prongs slightly pull them upward and let them drop down see picture to bring them back to the standing position just pull them up again Use of the Upper Basket The upper basket is designed for plates dessert plates saucers dinner plates up to 24 cm in diame ter salad bowls cups and glasses these should be arranged as shown in the pictures Glasses with long stems can be placed upside down in the raised cup racks y2. CONNECTION Voltage 220 240 V 50Hz POWER OF HEATING ELEMENT 2570 W OVERALL POWER 2720 W WATER SUPPLY PRESSURE minimum 7 psi 49 KN cm maximum 110 psi 758 KN cm CAPACITY STANDARD IEC PLACE SETTINGS 12 CONSUMPTION Water 19 It Electricity 1 4 kW h This appliance complies with the following E E C Directives C C 73 23 of 19 2 73 Low Voltage Directive and subsequent modifications 89 336 of 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications PID22GB 2 WARNINGS It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings These warnings are provided in the interest of safety You MUST read them carefully before installing or using the appliance Installation This appliance is heavy Care should be taken when moving it It is dangerous to alter the specifications or attempt to modify this product in any way Care must be taken to ensure that the appliance does not stand on the electrical supply cable Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Any plumbing work required to install this app
3. as possible correct arrangement of the items will give better washing results Light items plastic bowls etc should be loaded in the upper basket and arranged so that they do not move during washing You will improve drying results by leaving the dishwasher door ajar for at least 15 30 minutes as soon as the programme finishes To Save Energy Do not prewash dishes under running water Place dishes in the machine immediately after every meal and wait until the dishwasher is full before washing If necessary run the Rinse and Hold programme see Programme Chart on the following pages so that any food scraps do not become caked on the dishes while you are waiting to run the complete wash programme Select an economic programme when the baskets are not very full and or when the dishes are not very soiled following the instructions given in the Programme Chart ECO programme QUICK WASH programme You can also select NO DRYING or ECO DRYING in this case the drying will be less effective Care must be taken when opening the door as steam will escape Items not Suitable for Dishwashers The following should not be washed in the dishwasher Cutlery or dishes with wooden or horn handles or glued parts Handmade items wooden objects antiques or hand painted china Certain types of decoration can discolour when washed in a dishwasher Crystal ware and plastic objects if not guaranteed dishwasher proof should be w
4. specifically for use in dish washers Other types of salt i e table cooking salt contain high percentages of other substances which may reduce the efficiency of the softener To fill with salt unscrew the cap of the salt container Pour about half a litre of water inside the container or until it is full this is necessary only before filling with salt for the first time Then using the funnel pro vided pour in the salt until the container is full approx 1 5 1 8 kg Do not worry if water over flows from the unit when filling with salt this is quite normal Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket Screw the cap on tightly If you have inadvertently spilled salt select a wash programme immediately after All that is then required is to periodically top up the container with salt You are reminded of this by the Salt Indicator Light S on the control panel illumi nates when the salt has finished The salt container always has some water inside which will normally overflow when refilling with salt Important The Salt Indicator Light S on the control panel can remain illuminated for 2 6 hours after the salt has been replenished assuring the dishwasher remains switched on If you are using salts that take longer to dissolve then this can take longer The func tion of the dishwasher is not affected Caution Only fill with salt just before startin
5. spray arm pull the arm upwards holding one end To clean the nozzles of the top spray arm slide out the top basket whereby the spray arm will become accessible If you need to remove it take away the SID dispenser see instruc tions below and unscrew the retaining nut Clean the external surfaces of the machine and control panel with a soft damp cloth If necessary use only neutral detergents Never use abrasive products scouring pads or solvents acetone trichloroethylene etc Check that the Super Intensity Dispenser SID is not clogged with detergent residue or soil If necessary rinse it under running water after having removed it from x the basket by twisting it TA anticlockwise and pulling it 1 upwards Refit the dispenser by following the above instructions in reverse order Fasten it back onto the support by turning it clockwise Important Never use your dishwasher without the SID dispenser Prolonged Periods of Non Operation If you are not using the machine for any period of time you are advised to unplug the appliance and turn off the water fill the rinse aid dispenser leave the door ajar to prevent the formation of unpleasant smells leave the inside of the machine clean Frost Precautions Avoid placing the machine in a location where the temperature is below 0 C If this is unavoidable empty the machine close the water inlet tap disconnect the water inlet pipe an
6. the two pivots of the cross bar into the slot ted holes of the door Lift the decor panel until perfect alignment with the facia panel is obtained if the two brackets have also been used they will auto matically enagage in the special holes provided on the dishwasher door Once the correct position has been found open the door and fasten the decor panel on the lower section by means of the two long ing the holes through the inner door see fig Fixing to the adjacent units Insert the two fixing brackets into the slots provided in the top front part of the dishwasher as shown in the figure Secure the brackets to adjacent units using two 3 5 x 16 screws for each bracket Important The dishwasher must be secured against tilting Therefore make sure that the counter it is fitted under is suitably secured to a fixed structure adjacent kitchen cabinets wall Attention When the dishwasher is secured to the kitchen cabinets do not drill any holes into the sides of the machine Adjusting the door balance The door of the dishwasher is balanced when it is open in any position Fitting the decor panel may sometimes affect this balance In this case it will be necessary to adjust the balance as follows Half open the door and regulate the screws located on the kick plate By screwing or unscrewing these screws the tension of the door balancing springs is increased or d
7. 3amp BSI362 fuse Only ASTA or BSI approved fuses should be used The plug must not be used if the fuse cover carrier is lost The cover carrier is indicated by the coloured in sert at the base of the plug PINO8GB 5 A replacement cover carrier must be obtained from your local Zanussi Service Force Centre whose address is listed in the Customer Care Booklet which accompanies your instruction manual C This appliance complies with the follow ing E E C Directives 73 23 of 19 2 73 Low Voltage Directive and sub sequent modifications 89 336 of 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown USE Control panel o sr S ON OFF PROGRAMM E SELECTION W SID Y LOWER MM ECODRY BI NODRY H CANCEL DELAY START UPPER DRYING m l h OY 23 THE CONTROLS The controls are located on top of the door When se lecting a programme the door needs to be partially opened Audible signals indicate which operations the dishwasher is performing Short instruction accepted signal When any of the buttons are pressed a short audible signal informs you that the machine has accepted the instruction given if no signal is heard when a button is pressed this mean
8. Central Filter After each wash Scraps of food can sometimes accumulate in the cen tral filter A and should be periodically removed by rinsing the filter under running water To remove the filter simply pull it outward by the handle Once cleaned refit the filter by pushing it back to its original position until it engages Cleaning the Large Filter Every two months If necessary clean the large filter B on both sides under running water using a brush To take it out remove the spray arm by pulling it up ward on one side turn the column C anticlockwise by 90 and then slide out the filter Once cleaned refit it follow ing the above instructions in reverse order Ensure the filter is in its original position the handle of filter A should be pointing towards the front of the appliance Caution the dishwasher must not be used without filters Incorrect repositioning of the filters will produce poor washing results Cleaning of the filters is vital to ensure correct operation of the machine PMA10GB 14 Internal and External Cleaning You must ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend the use of a specific dishwasher cleaner every 3 months or run a wash programme without dishes using detergent Check that the spray arm nozzles are not obstructed To remove the bottom
9. STRUCTION BOOKLET 0000000 ZANUSSI CONTENTS Warniids eter bene ti erat ee page 3 Installation asus ads er rds Vi Sada eie ene Da ds sse gie so ed tren page 4 Positioning levelling water supply connections water outlet connection oooooooooooo page 4 The electrical connections ooooccoocco eh m hr page 5 US DTE page 6 Gontrol panel act batte obtener NIS Ep hee Ei RUE DICE adt tice ess page 6 The water softener filling with salt lille page 8 Use of rinse aid use of detergent 0 0 cette eee page 9 Loading the machine use of the lower basket use of the upper basket 2000 eeu page 10 Adjusting the height of the upper basket 0 0c cece eee page 11 HeIpDIUEDIDES o oed oed o dud owed bode ea ere dox aes pao Aa sche page 11 Washing programmes ooo page 12 Operating sequence o page 13 Maintenance and cleaning 0 ccc ccc cence teens page 14 Cleaning the central filters cleaning the large filter internal and external cleaning page 14 Prolonged periods of Non Operation o ooococcocco hs page 15 Servicing lord re ea mitia exime bake Usa Ada tines da page 16 Building in Oe a da page 18 Peace of mind for twentyfour months Luuuuuuuuussss page 20 TECHNICAL SPECIFICATIONS DIMENSIONS Width cm 59 6 Height cm 81 8 87 8 Max depth cm 55 5 Max depth with door open cm 115 ELECTRICAL
10. a Caution When loading the dishes ensure that you do not cover the water inlet ua funnel in the middle of the P upper basket Before closing the door ensure that the spray arms can rotate freely Adjusting the Height of the Upper Basket If washing very large plates over 27 cm and up to 31 cm in diameter you can load them in the lower basket after moving the upper basket to the higher position as follows pull out the basket grasp it on the two sides and pull it upwards until the mechanism is en gaged and the basket is stable When the top basket is in the higher position it will only take plates up to 20 cm in diameter and you will not be able to use the raised cup racks To put the basket back in the lower position grasp the two sides pull upwards again then allow the basket to drop back down slowly keeping hold of it Warning never lift or lower the basket on one side only HELPFUL HINTS For Best Washing Results Before loading remove all scraps of food and soak very heavily soiled pots and pans Always arrange saucepans cups and glasses etc up side down Tilt items with convex or concave surfaces so that the water drains off easily Long items of cutlery such as ladles carving knives etc should be positioned horizontally in the upper basket Avoid contact between the dishes as far
11. ake sure that the water fill and drain hoses and the power supply cable are not bent or kinked Fitting the panel onto the door The door on this model is designed for the overlay of a panel having the following dimensions Width 596 mm Height 644 to 714 mm max Thickness 20 mm max Weight 2 to 7 5 kg max Note The panel height should not be more than what indicated otherwise complete opening of the door will no longer be possible as the panel hits against the dishwasher plinth PIIO3GB 18 Mounting of decor panel onto the door The height of the panel depends on the height of the plinth of adjacent kitchen units see kitchen plinth adjustment The panel must be fitted with a handle as the dish washer handle will be hid den by the panel Drill the panel with a Y 2x12 bit according to the dimensions indicated in the figure 596 max Fix the cross bar onto the panel using four 3 5x16 screws provided Reduce the length of fixing screws according to thickness of panel If for aesthetic matching the panel is provided with a false drawer fitted or carved on the panel itself the two brackets provided should also be used Fix the brackets according to the measurements shown in the figure by us ing four 3 5 x 16 screws 596 max 546 Reduce the length of fixing screws according to thickness of panel Mount the decor panel by inserting
12. as elapsed the programme starts automatically If you wish to interrupt the wash programme at any time press the ON OFF bo button To restart the machine press this button again and the wash programme will resume at the point at which it was interrupted 8 At the end of the wash programme The machine stops automatically An intermittent audi ble signal lasting about 5 seconds informs you that the programme has finished In the digital display ap pears 0 This signal remains until a button is pressed Switch of the dishwasher by pressing the ON OFF Bo button Turn off the water tap and switch off at the mains supply Wait a few minutes before removing the dishes in this way they will be cooler and the drying will be improved Empty the lower basket first and then the upper one this will avoid water dripping from the upper basket onto the dishes in the lower one Caution In general it is not advisable to open the door while the machine is working if the door is opened however a safety device ensures that the machine stops 9 Cancel the wash programme To cancel a wash programme which is running press the CANCEL button until the short instruction accepted signal about 2 seconds is heard The two zeros appear OL in the digital display indicating that the previous setting has been cancelled and a new programme can now be selected MAINTENANCE AND CLEANING Cleaning the
13. ashed by hand You are advised to place them in the upper basket and to select a delicate programme Certain types of glass can also become opaque after being washed several times in a dishwasher Silver cutlery tends to go black if mixed with steel cutlery Place it in the cutlery basket separate from the others Iron and cast iron objects can rust and stain other items Aluminium tends to go black copper pewter and brass tend to stain Caution You are advised not to load very small or plastic items which can fall through the baskets Note When buying new dishes ensure that they are dishwasher proof WASHING PROGRAMMES Recommended quantity of detergent Pro Degree of soil and Recommended Required Cycle i in the SID ipti gramme type of load programme Pushbuttons dis e eine ee Description Dispenser Any RINSE 1 cold rinse to avoid Partial load to be com AND EOM D food scraps from 1 pleted later in the day HOLD DO sticking to the dishes Heavy soil INTENSIVE 2 level 1 level Prewash up to 50 C Crockery cutlery pots 70 C PROGRAMMES y dessert dessert Main wash up to 70 C 2 andpans eae ey DO spoons spoon 2 cold rinses 20 g 10 g 1 hot rinse up to 70 C Thermal drying Normal soil NORMAL 1 heaped 1 level Prewash up to 50 C 3 Crockery cutlery pots WITH PROGRAMMES dessert desser
14. asher features fill and drain hoses which can be turned either to the left or the right to suit the installation Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on the spacers on either side of the cabinet IN11 IN12 If the door does not close correctly loosen or tighten the adjustable support feet until the machine is perfectly level Water Supply Connections This dishwasher must be permanently plumbed into a cold water supply The water pressure must be within the limits given in the technical specifications as it will not function cor rectly if pressure is outside these specifications Your local Water Authority will advise you on the average mains pressure in your area Where the water is supplied via a cold water storage cistern you can work out the pressure yourself by mea suring the vertical distance or head between the machine s inlet hose and the outlet from the cold water storage cistern allowing roughly 1 psi for every 2 feet For making the connection itself the coupling nut fitted to the machine s supply hose is designed to screw onto either a 3 4 inch gas thread spout or to a pur pose made quick coupling tap such as the Press Block CA04 To make this easier the hose itself may be turned to the left or the right In either case be sure t
15. at the end of the programme press this button again This indicator light will flash when the rinse aid has run out to remind you to top it up 3 SALT indicator light S This indicator light will flash when the salt has run out to remind you to top it up If your water is level 0 there is no need of salt therefore the salt indicator light will always remain on 4 Digital display 5 PROGRAMME SELECTION button To select the required programme press this button until the number corresponding to the chosen pro gramme appears in the digital display 4 see wash programme guide To start the programme simply close the dishwasher door A long audible signal about one second informs you that the programme is starting If you open the door whilst the programme is in opera tion in the digital display appears the remaining time in minutes to the end of the washing cycle 6 SID Indicator Light This pilot light comes on when programmes 2 3 5 and 8 are selected to remind you that these pro grammes require a small amount of detergent to be added in the Super Intensity Dispenser SID located in the centre of the upper basket Follow the instruc tions given in the Washing programme chart Attention if the half load 7 option is selected the SID light will illuminate only with programme 2 Intensive 70 C 7 Half load UPPER LOWER pushbutton By pressing this button washing can be confin
16. ate freely 6 Measure out detergent Pour the required amount of detergent into the dispenser according to the indications in the Washing Programmes chart and close the lid 7 Set the programme Press the PROGRAMME SELECTION button until the number corresponding to the required programme appears in the display The indicator light continues to flash until the programme is started The following options may also be selected ECO DRY by pressing the relevant button The pilot light corresponding to the selection made comes on NO DRY by pressing the relevant button The pilot light corresponding to the selection made comes on UPPER LOWER by pressing this button washing can be confined to a single basket Depress the button until the pilot light corresponding to the basket selected illuminates upper o lower Always remember to load all the dishes into the basket selected if you choose this option DELAY START by depressing this button the start of a programme can be delayed from a minimum of 1 hour up to 9 hours PSO18GB 13 7 Starting the wash programme Open the water tap Close the dishwasher door An audible signal lasting about 1 second informs you that the programme has started If a delayed start has been selected the dishwasher starts the countdown and the number of hours to go before the programme starts appears in the display A flashing H indicates that the function is active Once the set delay h
17. attling against each other m The spray arms are knocking against the dishes The dishes are not quite dry m The dishes have been left too long inside the machine m The rinse aid has run out or too little is being used The door is difficult to close m The dishwasher is not level or is not properly built in If after the above checks the fault persists call your local Zanussi Service Centre whose address can be found in the accompanying Customer Care Booklet and can also be found in your local telephone directo ry under Z Please make sure you give the model and serial number of the appliance This information can be found on the rating plate located on the right hand side of the dishwasher door see picture JEAN Prod No Ser No Mod RAOI Original spare parts can be purchased from Zanussi Service Centres In guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown Please note that proof of purchase is required for any in guarantee service calls Service details adhesive label When you return your guarantee card to Zanussi Ltd you will receive an Appliance Guarantee And Maintenance Record together with an adhesive label containing the telephone number of your local Zanussi Service Centre The label can be adhered to the ma chine or adjacent
18. d empty it Moving the Machine If you have to move the machine you are moving house etc unplug it turn off the water tap remove the water inlet and discharge hoses pull the machine out together with the hoses Caution avoid over tilting the machine during transport PMA04GB 15 SERVICING Certain problems are due to lack of simple mainte nance or oversights and can be solved easily without having to call out an engineer Therefore before call ing the Service consult the check list here below The following alarms A3 A5 A6 A1 A2 A7 flash in the digital display window The dishwasher fails to start or stops during operation all the lights are out except for the alarm in the digital display all buttons are inoperative except for the ON OFF button If the dishwasher displays the following fault codes please carry out the following checks If A3 is displayed or the dishwasher stops m he spray arms are not rotating Check the crock ery is loaded correctly m The filters are blocked Clean the filters and press the start button If A5 is displayed or the machine will not fill with water m The water tap is off Turn the water tap on and press the start button m The water supply has been cut off Wait for it to be restored then press the start button m The inlet hose is kinked Straighten the hose and press the start button m The water inlet hose is blocked Clean the filter at
19. e starting any of the dishwashing programmes except for the rinse and hold programme load the detergent in the dispenser Use only tablets powder or liquid detergents specifically designed for domestic dishwashers Unsuitable detergents such as those for washing by hand do not contain the right ingredients for machine washing and hamper correct functioning of the machine To open the dispenser lid pull the catch D This will open it To help you to correctly dose the right amount of detergent inside the con tainer there are two refer ence marks MIN 15 ml MAX 30 ml a Ao Oe i After filling the dispenser with detergent close the lid At the end of any washing programme the lid is always open ready for the next wash All the programmes with a warm prewash require a For the Intensive programme For this programme suitable for particularly dirty pans and dishes is selected an extra 10 g of detergent must be placed in the SID Pull out the basket and add detergent Important Never use your dishwasher without the SID dispenser Since SID also ensures correct distribution of the water to the upper spray arm running the dishwasher without it will impair the washing results The amount of detergent to be used varies depending on how soiled the dishes are and the type of dishes being washed We recommend the amounts shown in the programme chart on the next pages Since not all detergent
20. eat plates 70 C before serving or remove dust from dishes which have not been used for a long time This programme is equivalent to IEC436 DIN 44990 Standard place setting 12 Recommended quantity of detergent 20 g in the dispenser 5 gin the SID This is a special programme for quick washing approx 33 minutes a full load of lightly soiled dishes glasses and crockery except pots so that you may re use them promptly Due to the shortness of this programme no drying phase is provided pilot light of NO DRY illuminated If you wish an economic drying select the ECO DRY button Remember if you select the option half load UPPER LOWER reduce the quantity of detergent and only for programme n 2 Intensive pour detergent in the SID PTP23GB 12 Operating Sequence 1 Check that the filters are clean see cleaning instructions 2 Switch on at the main supply 3 Depress the ON OFF pushbutton b In the display appears the number of the last pro gramme selected and the PROGRAMMES SELEC TION pilot light flashes 4 Check that there is salt and rinse aid The indicator lights will flash if they need topping up 5 Load the dishes Remove larger scraps of food Pull the lower basket out and arrange the saucepans plates and cutlery in it Pull the upper basket out and arrange the plates saucers glasses and cups etc in it Slide the baskets back into the machine Ensure that the spray arms can rot
21. ecreased respectively Attention The weight of the panel should be within the limits given in the dimensions of the panel otherwise balancing the door will not be possible Levelling Make sure that the dishwasher door closes properly without rubbing on sides Otherwise level the machine by slightly screwing or unscrewing the two front feet until perfect closure of the door is reached Kitchen plinth adjustment To allow correct opening of the door it is sometimes necessary to cut the kitchen plinth Refer to the cutting table below According to dimensions of a and b as shown on the figure you will find on the following table the depth x of the cut to be made on the plinth The dimensions a and b of the table are those more frequently used in the kitchen furnitures E 2 c a oO Q tt 95 dimensions in mm 600 mm minimum De N Dimensions of the cut on the plinth A PIIO4GB 19 PEACE OF MIND FOR TWENTY FOUR MONTHS Zanussi guarantee conditions This guarantee is in addition to your statutory and other legal rights We Zanussi Ltd undertake that if within twenty four months of the date of the purchase this ZANUSSI appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condit
22. ed to a single basket instead of both Depress the button until the indicator light corresponding to the basket selected illuminates This is very useful and economical when only a few dishes need washing Remember to load all the dishes into the basket selected Do however follow the instructions given in the section Loading your machine 8 ECO DRY button By pressing this button the last rinse and the hot air drying cycle will be shorten making a considerable energy saving The corresponding indicator light comes on 9 NO DRY button By pressing this button the last rinse water will be cold and hot air drying cycle will be omitted The corresponding pilot light comes on If both the ECO DRY and NO DRY indicator lights are out the full drying cycle will be carried out PPC27GB 7 10 DELAY START button The start of the programme can be delayed by a mini mum of 1 hour up to a maximum 9 hours How to set DELAY START By pressing the button H will appear on the digital display this means that you have delayed the start of the programme by 1 hour By pressing the button repeatedly you can delay the start of the programme up to a maximum of 9 hours By pressing the button one more time you go back to the programme setting Press the button again to select the number of hours by which you wish to delay the programme start up to a maximum of 9 Close the dishwasher door to start the co
23. elow the level corresponding to the hardness of your water and the required adjustments Level French Degrees German Degrees ppm TH dH Parts per Million 0 0 4 0 8 0 80 1 5 8 9 14 81 140 2 9 11 15 20 141 200 3 12 17 21 30 201 300 4 18 22 31 40 301 400 5 23 28 41 50 401 500 6 29 33 51 60 501 600 7 34 39 61 70 601 700 8 40 45 71 80 701 800 9 46 50 81 90 801 900 The water softener is factory set at level 4 as this suits most users To set the dishwasher to a different level proceed as follows Press the ON OFF pushbutton on Press the UPPER LOWER and DELAY START simultaneously for about 5 seconds until the short instruction accepted signal is heard an L followed by number 4 the hardness level set in factory will appear in the digital display L4 A UPPER yy LOWER gm ECODRY mg NODRY A CANCEL DELAY START soss MM Press the UPPER LOWER button as many times as necessary to make the required level appear in the display The level increases by 1 each time the button is pressed 5 seconds after this button has last been pressed the machine returns to programme setting mode and memorises the level set PAA14GB 8 Important Salt MUST be used regularly from level 1 upward If your water is level O it is already soft and therefore there is no need to use salt Filling with Salt Only use salt designed
24. furniture Protection against flooding To protect your dishwasher from water damage it is equipped with a flood protection system It features an flood protection float switch in the floor tray This comes into operation in the event of any water leaks in the machine while the machine is switched on When the flood protection comes into operation the dishwasher remains inoperative and the A5 fault code will be displayed To repair the machine call the Service Centre PRA24GB 17 BUILDING IN Building in features This dishwasher is designed to be fitted under a kitchen counter or sink In either case it is essential that the recess dimensions indicated in the picture are followed No further openings for venting of the dishwasher are required but only to let the water fill and drain hoses cable pass through The recess height may be anywhere between 820 and 880 mm from the floor since the dishwasher incorporates levelling feet adjustable over a wide range max 60 mm Adjust the height of the appliance by turning these feet A distance of 2 mm should be allowed between the top of the dishwasher and the counter top Fitting under a counter kitchen worktop or sink It is absolutely essential that the dishwasher is disconnected from the electricity supply before gaining access to any internal component Fit the dishwasher into the appropriate housing space and connect it M
25. g one of the complete washing programmes not the Rinse and Hold programme This will prevent any grains of salt or salty water which may have been spilled remaining on the bottom of the machine for any period of time This could cause corrosion Rinse Aid This liquid gives the dishes a shiny finish and improves drying It is automatically added during the hot rinse The dispenser which is positioned inside the door holds about 110 ml of rinse aid which is sufficient for 16 40 dishwashing programmes depending upon the dosage setting Filling with Rinse Aid Open the container by turning the lid A anticlockwise Add rinse aid until the container is completely full approx 110 ml The indicator B will be completely dark Top up with rinse aid when the RINSE AID indicator light 3 on the control panel flashes Remember to CLOSE the lid after every refill Caution Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash Adjusting the Dose According to the finish and drying results obtained by means of the 6 position selector C position 1 minimum dose position 6 maximum dose Gradually increase the dose if there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish streaks on the dishes Caution Do not put liquid detergent into the rinse aid compartment Use of Detergent Befor
26. he machine is draining as this could cause the water to siphon back into the machine The electrical connections WARNING THIS APPLIANCE MUST BE EARTHED The manufacturer declines any liability should this safety measure not be observed If the plug that is fitted to your appliance is not suitable for your socket outlet it must be cut off and the appropriate plug fitted Remove the fuse from the cut off plug The cut off plug should then be disposed of to prevent the hazard of shocks in case it should be plugged into a 13 amp socket in another part of your home Important The wires in the mains lead are coloured in accor dance with the following code Green and Yellow Earth Blue Neutral Brown Live If you fit your own plug the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug proceed as follows GREEN amp YELLOW 13 AMP FUSE N ceo CORD CLAMP Connect the Green and Yellow earth wire to the ter minal in the plug which is marked with the letter E or the earth symbol amp or coloured green and yellow Connect the Blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black Connect the Brown live wire to the terminal in the plug which is marked with the letter L or coloured red The plug moulded onto the lead incorporates a fuse For replacement use a 1
27. ion that m The appliance has been correctly installed and used only on the electricity supply stated on the rating plate m The appliance has been used for normal domestic purposes only and in accordance with the manufac turer s operating and maintenance instructions m The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us All service work under this guarantee must be under taken by a Zanussi Service Force Centre Home visits are made between 8 30 am and 5 30 pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Any appliance or defective part replaced shall become our property Exclusions This guarantee does not cover m Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic m Costs incurred for calls to put right machines improperly installed or calls to machines outside the UK and the Republic of Ireland m Appliances found to be in use within a commercial or similar environment plus those which are the subject to rental agreements m Products of Zanussi manufacture which are NOT marketed by Zanussi Ltd m EU Countries The standard guarantee is applica ble but subject to the owner s responsibility and cost to ensure the appliance meets the standards set by the country to which the product is take
28. liances should be carried out by a qualified plumber or competent person Built in dishwashers only The appliance must be secured to the underside of the worktop using the brackets provided Failure to do this could result in an unstable appliance which may cause damage or injury Child Safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product During Use Zanussi dishwashers are designed to be used for washing normal household utensils Items that are contaminated by petrol paint steel or iron debris corrosive acidic or alkaline chemicals are not to be washed in a dishwasher Under no circumstances should you open the door whilst the appliance is in operation Always turn off the appliance before opening the door When finishing loading or unloading close the door as an open door can be a hazard Unplug the appliance and turn off the water after use If your house is fitted with a water softening unit or if you live in a soft water area it is not necessary to add salt to the water softening unit in the dishwasher PAVO4GB 3 Do not put in your dishwasher cutlery with wooden or horn handles or glued parts bronze cutlery saucepans with wooden handles unless they are sold as dishwasher proof aluminium ware crystal ware leaded glass plastic articles unless sold as dishwasher proof antique china or fine decorated china unle
29. n The Zanussi company in the country concerned will be pleased to advise further Sight of your purchase receipt will be required by them PGA05GB 20 bu Total Chlorine free 152995 82 0 Printed in Italy 9 0 1096
30. o incorporate the strainer A supplied with the machine into the joint See picture CA06 PINO7GB 4 Caution the retaining ring must be correctly fitted to avoid water leaks Avoid bends or kinks in the hose which could prevent or slow down the flow of water If the machine is connected to new pipes or pipes which have not been used for a long time you are advised to run the water for a few minutes before connecting the inlet hose This will prevent deposits of sand or rust clogging the inlet hose filter Water Outlet Connection The end of the drain hose can be connected as follows to the sink outlet siphon securing it if necessary with a clip to a wall outlet provided with vent hole minimum internal diameter 4 cm The waste connection must be at a height of between 30 cm minimum and 100 cm maximum from the floor CS05 It makes no difference which way the drain hose faces either to the right or left of the dishwasher Avoid bending or kinking the hose as this could prevent or slow down the discharge of water If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided Likewise the internal diameter of the couplings used for connection to the waste outlet must be no smaller than the diameter of the drain hose Note The sink plug must not be in place when t
31. s are the same you should also consult the instructions on the packet Remember that insufficient quantities of detergent will produce poor washing results whereas an excessive amount of detergent does not improve washing results and is also wasteful Using no more than the correct amount of detergent also contributes to reducing pollution Zanussi recommends the use of FINISH dishwasher detergent PBR15GB 9 Phosphate free detergents with enzymes These new detergents although welcome from an ecological point of view react far more susceptibly to water hardness than conventional products Therefore in order to avoid white lime deposits on crockery and the inner tub you should add salt in the water softener even if the hardness of your water is as low as 4 dH 7 TH when using these new detergents Loading your Machine Before placing dishes in the machine remove any scraps of food from the plates small bones toothpicks fish bones scraps of meat and vegetables fruit skins etc to avoid clogging the filters and consequently reducing performance Open the door and slide out the baskets to load the dishes Use of the Lower Basket The lower basket is designed to take saucepans lids plates up to 27 cm in diameter salad bowls cutlery etc Serving dishes and large lids should be arranged around the edge of the basket ensuring that the up per spray arm can turn freely M AN WARN
32. s that a programme is already running or that the programme selected does not include this function Long programme run signal A continuous audible signal lasting about one second heard only when you close the dishwasher door informs you that the wash programme is starting Intermittent end of programme signal An intermittent audible signal lasting in total five seconds informs you that the wash programme has ended To deactivate these audible signals press both the CANCEL and DELAY START buttons together for about 3 seconds until three short signals are heard A Feen S084 CANCEL DELAY START To reactivate the audible signals press both buttons together again for about 3 seconds until the short instruction accepted signal is heard 5 PPC26GB 6 6 10 11 1 ON OFF button BJ ON Press this button to preset the dishwasher to accept settings selection of wash programmes drying options delayed start etc The salt pilot light S 3 and the rinse aid light 3 2 comes on if salt or rinse aid are low and the programme selector light 5b flashes The number corresponding to the programme selected previously appears in the digital display OFF When the wash programme has ended the dishwasher stops automatically an intermittent audible signal lasting about 5 seconds informs you of this and two zeros L appear in the digital display To switch off the dishwasher
33. ss sold as dishwasher proof Always check with the manufacturer of the item if in any doubt A chemical reaction can occur between silver cutlery and stainless steel cutlery As a precaution do not wash together Care should be taken when cleaning the bottom door seal and hinge area as any exposed metal edges may cut if care is not taken This product should be serviced by an authorised Zanussi engineer and only genuine Zanussi spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Zanussi Service Centre Always insist on genuine Zanussi Spare Parts Conservation In the interests of the Environment When disposing of your old appliance Help to keep your country tidy use authorised disposal sites for your old appliances The materials used on this appliance marked with the symbol 3 are recyclable Check with your local Council or Environmental Health Office to see if there are facilities in your area for re cycling this appliance If you are discarding an old appliance that has a lock or catch on the door you must ensure that it is made unusable to prevent young children being trapped inside INSTALLATION Remove all packaging before positioning the machine Positioning If possible position the machine next to a water tap and a drain The dishw
34. t Main wash up to 65 C SELECTION D l n and pans PREWASH Do spoo spoon 1 cold rinse 65 15 g 10 g 1 hot rinse up to 65 C Thermal drying Normal soil NORMAL NO 2 heaped Main wash up to 65 C 4 Crockery and cutlery PREWASH ECON D dessert 1 cold rinse pots and pans 65 c DO Spoons 1 hot rinse up to 65 C 25 g Thermal drying Normal soil ECONOMY 1 heaped 1 level Prewash up to 50 C Crockery and cutlery WITH PROGRAMMES D dessert dessert Main wash up to 55 C 5 PREWASH FECE Do on spoon 1 cold rinse 55 15 9 10 g 1 hot rinse up to 65 C Thermal drying Normal soil ECONOMY 2 heaped Main wash up to 55 C 6 Crockery and cutlery NO PROGRAMMES D 4 dessert 1 cold rinse PREWASH DO spoons 1 hot rinse up to 65 C 55 c 25 g Thermal drying Light soil DELICATE 1 heaped Prewash up to 40 C China and WITH PROGRAMMES b dessert Main wash up to 45 C 7 glassware with PREWASH Bar Do Spoon 1 cold rinse delicate decorations 45 15 9 1 hot rinse up to 60 C Thermal drying Light soil DELICATE 1 heaped Main wash up to 45 C China and NO PROGRAMMES D dessert 1 cold rinse 8 glassware with PREWASH Fun Do spoon 1 hot rinse up to 60 C delicate decorations 45 159 Thermal drying Light soil QUICK 1 heaped Main wash up to 50 C 9 Crockery and WASH more D dessert 2 cold rinses party crockery 55 DO TE 2 1 hot rinse up to 70 C Crockery and PLATE pO D l Thermal drying 1 0 cutlery WARMER SELECTION DO This is a programme designed both to h
35. the end of the inlet hose and press the start button m The filters are blocked Clean the filters and press the start button If A6 is displayed or the machine will not drain m The drain hose is kinked Straighten the hose and press the start button m The sink drain is blocked Clear the blockage and press the start button m The drain hose extension is not correct Follow the instructions for connecting to the waste and press the start button m There is no air vent in the end of the drain hose If after these checks the fault codes remain displayed or the fault codes A1 A2 A4 or A7 appear contact your local Zanussi Service Centre PRA20GB 16 For washing or drying problems please carry out the checks listed below The dishes are not clean poor wash m The baskets are too full m The dishes have not been arranged correctly m The spray arms do not rotate m The spray arms are blocked m The water inlet funnel in the centre of the upper basket is covered by dishes m The filters are clogged m The filters are not in position m Not enough detergent has been used or it is unsuitable m The detergent is old or has gone hard m The salt container cap is not properly closed m The washing programme selected is too gentle Visible lime deposits or white film on the dishes m There is no salt or the softener has not been adjusted to the hardness of the water The machine is noisy m The dishes are r
36. untdown a long audible signal about one second informs you that the function is active If you open the door again you will see in the display 4 how long there is to go in hours before the programme starts A flashing H in the digi tal display means that the delayed start function has been activated Opening the door has no effect on a countdown which has already been started 11 CANCEL programme change button If you wish to cancel a programme which is already running or a setting which has just been made press this button for about two seconds until the short instruction accepted signal is heard In the digital display will appear 00 to indicate that the dishwasher has been reset and that a new programme and new options can be selected The Water Softener Water contains varying amounts of lime and mineral salts depending on the area in which you live these are deposited on the dishes leaving white marks The higher the content of these salts the harder your water will be The hardness level is measured on 3 equivalent scales French Degrees German Degrees or Parts Per Million Contact your local Water Authority to find the exact water hardness level for your area The dishwasher is equipped with a softener which uses special dishwasher salt to provide lime free softened water The softener can treat water hardness up to 50 German degrees via 9 adjustment levels Find on the table b
Download Pdf Manuals
Related Search