Zanussi ZHI 600 Instruction Manual
Contents
1. Under no circumstances should you attempt to repair the appliance yourself Repairs carried out by inexperienced persons may cause injury or more serious malfunction Refer to your local Zanussi Service Force Centre Always insist on genuine spare parts YOUR APPLIANCE OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen it will not extract steam To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing Cooker Hood Controls S Automate Viersswileh ee en a il M Fan Speed Control Position O Off Position 1 Low Position 2 Normal Position 3 Boost L Light ON OFF control To Operate Open the visor and select the required functions L Ail r r a whl J y JN Ly Li Why in 0911 Il i 1 1 el R da II UHAI nl N i iy Extraction The contaminated air enters the hood passing through the grease filter and out through the ducting into the atmosphere Recirculation A charcoal filter enables the cooker hood to recirculate the air back into the kitchen A When the extraction mode is selected the charcoal filter is not required Never do flamb cooking under this cooker hood Take extra care when frying and never leave frying pans unattended during use as o2. ZANUSSI Thank you for buying a Zanussi product To enable you to use your appliance effectively and safely please read this instruction book carefully before using the appliance and retain for future reference If you require guidance in the use of the appliance or require further information on Zanussi Products please contact our Customer Care Department For general enquiries concerning your Zanussi appliance or for further information visit our website at http www zanussi co uk Fax 01753 538972 calls to this number may be recorded for training purposes To register ownership please ensure you complete and return the guarantee card supplied with the appliance For the User Important Safety Information Your Appliance Operating Instructions Cooker Hood Controls To Operate Extraction mode Recirculation Maintenance and Cleaning External Cleaning Synthetic Paper Grease Filter To Replace the Synthetic Paper Grease Filter Charcoal Filter Optional Extra To Remove the Charcoal Filter Changing the Light Bulb Something Not Working Service and Spare Parts Guarantee Conditions For the Installer Installation Instructions Technical Information Electrical Connections Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Ducting Clearance Height Unpacking The fixing kit comprises Fitting the Wall Brackets Venting To Fit the Ducting Recircul
3. The kitchen is adequately vented to allow the entry of fresh air If set up for recirculation check that the charcoal filter is still effective If set up for extraction check that the ducting and outlets are not blocked The cooker hood has switched off during The safety cut out device has been tripped operation Turn off the hob and then wait for the device to reset If after all these checks the problem persists In guarantee customers should ensure contact your local Service Force Centre that the above checks have been made as quoting the model and serial number the engineer will make a charge if the fault is not a mechanical or electrical Please note that it will be necessary to breakdown provide proof of purchase for any in guarantee service calls SERVICE AND SPARE PARTS If you require an engineer or wish to purchase spare For general assistance with your appliance or for parts contact your local Service Force Centre by information on Zanussi products please contact our telephoning Customer Care Department 08705 929929 Your telephone call will be routed to your local Service Force Centre For further details please see the accompanying customer care book calls to this number may be recorded for training purposes PEACE OF MIND FOR TWENTY FOUR MONTHS STANDARD GUARANTEE CONDITIONS We Zanussi Ltd undertake that if within twenty four months of the date of the purchase this Zanussi built in appliance
4. screws provided Once the brackets are secured lift the hood squarely to the wall slightly higher than the brackets Lower the cooker hood until it is located onto the two brackets Ensure that the cooker hood is correctly located before letting go By loosening the screws in the extension arm the hood can be aligned with the front of the adjoining wall cabinets The hood should be secured on each side to the adjoining wall cabinets using the 4 x 15mm 1 2 ins security screws provided Adjust the lower spacer panel at the rear of the hood to close the gap to the wall Decor Panel The dimensions of the door panel should be 59 6cm 23 1 2 ins wide by 35cm 13 3 4 ins in height gt Fitting a Decor Panel to the Hood Visor Remove the complete visor assembly by pulling open into the operating position simultaneously press down on the release catch located behind the visor on the left hand side of the casing Using the paper template provided mark the screw hole positions on the reverse side of the decor panel Ensure that the paper template is aligned with the top edge of the decor panel SS en ce ATA F SEHR ARA M Be N 14 A Failure to align the top edge of the decor panel with the template will prevent the visor from opening when installed 3 Before drilling use a tape measure to check the distances of the screw holes as given on the template The template may have altered due t
5. Check the hole distances are correct with a tape measure as stated on the template 3 At this stage it is important to allow 15mm 1 2 clear space above the cooker hood to enable it to be hooked onto the brackets and for subsequent removal for decorating or servicing 12 Venting The hood is more effective when used in the extraction setting ducted to the outside Venting kits may be purchased through your retailer or DIY store and must be ducted to an outside vent of 100mm 4 minimum The ducting used must be manufactured from fire retardant material When the hood is ducted externally the charcoal filter must be removed ES To Fit the Ducting 1 Open the grille by pressing inwardly on the actuator bolts at each side of the grille while pulling the grille panel downwards The grille panel will slide into the intermediate position Raise the lower edge of the grille forward through 45 angle until the grille becomes detached from the slide mechanism 2 Align the flat sides on the spigot with the recesses in the top of the casing Insert and snap fix the spigot into the casing 3 Connect the ducting to the spigot and make an air tight seal 4 Remove the charcoal filter Recirculation The charcoal filter optional extra must be fitted for recirculation 13 gt Fitting the Cooker Hood to the Wall 1 Fit the brackets with the round ends facing downwards using the plastic rawl plugs and
6. regarding voltage on the rating plate inside the cooker suppression of radio and television hood interference This appliance conforms to BS 800 1988 and 10 INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown A All installations must comply with the local authorities requirements for the discharge of exhaust air Incorrect installation may affect the safety of this cooker hood Installation Requirements A Before installation check the wall to which the cooker hood is to be fitted for electric cables water pipes or gas If it is necessary to fix the hood to a hollow construction plaster or partition board structure then it should be sufficiently reinforced to be quite rigid in the area of the cooker hood mounting brackets and the appropriate rawl plugs used for this type of fixing not supplied Ducting The ducting must be fire retardant 100mm 4ins in diameter and the length should be no more than 3 metres with one 90 bend 2 metres with two 90 bends Bends of more than 90 will reduce the efficiency of the hood and reduce the airflow Clearance Height The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications If the output of the appliance b
7. L SUPPLY Voltage 50Hz 220 240 V POWER CONSUMPTION 190 W FAN MOTOR 110 W LAMP 2x40W 80 W SUITABLE FOR INSTALLATION ABOVE ELECTRIC HOB 7 KW max GAS HOB 10 KW max SLOT IN GAS COOKER 13 5 KW max SLOT IN ELECTRIC COOKER 12 4 KW max CHARCOAL FILTERS Supplied Note CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89 336 Electromagnetic compatibility and subsequent modifications and Low Voltage directive 72 23 E ELECTRICAL CONNECTIONS WARNING DOUBLE INSULATED DO NOT EARTH Electrical Requirements This appliance is fitted with a 2 core mains Any permanent electrical installation must cable and must be permanently connected to comply with the latest I E E Regulations and the electricity supply via a double pole switch local Electricity Board regulations For your own having 3mm minimum contact gap on each safety this should be undertaken by a qualified pole A Switched Fuse Connection Unit to electrician e g your local Electricity Board or a BS1363 Part 4 fitted with a 3 Amp fuse is a contractor who is on the roll of the National recommended mains supply connection Inspection Council for Electrical Installation accessory to ensure compliance with the Safety Contracting NICEIC Requirements applicable to fixed wiring instructions Electrical Connection Before connecting to the mains supply ensure ae that the mains voltage corresponds to the EEC Directive No 78 308
8. al wire retaining clips 4 Clean the metal grille and clips before replacing the grease filter Handle the wire clips with care and keep away from children as they have sharp points A The synthetic paper grease filter cannot be cleaned It must not be washed Charcoal Filter for use in recirculation mode The charcoal filter cannot be cleaned it should be replaced approximately every three months or more often if the hood is used for more than three hours per day I To Remove the Charcoal Filter 1 Remove the thumb screw through the center of the charcoal filter from the motor support 2 The charcoal filter can now be removed This appliance can be a fire hazard if the grease and charcoal filters are not replaced as recommended Changing the Light Bulb The bulb should be replaced with a 220 240 volt 40 watt clear cylindrical shape bulb with a small E14 screw thread Replacement charcoal filters grease filters and light bulbs can be obtained from your local Service Force Centre SOMETHING NOT WORKING If having followed these instructions carefully your cooker hood fails to work properly please carry out the following checks Symptom The cooker hood will not start Check the hood is connected to the electricity supply Check that the fan speed control is set to 1 2 or 3 The cooker hood is not working effectively The fan speed is set high enough for the task The grease filter is clean
9. ation Fitting the Cooker Hood to the Wall Decor Panel Fitting a Decor Panel to the Hood Visor To Refit the Hood With Decor Panel Attached Adjustment Guide to use the instruction book The following Symbols will be found in the text to guide you through the instruction book A Safety instructions is Step by step instructions IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety Ensure that you understand them all before installing or using this appliance Your safety is of paramount importance If you are unsure about any of the meanings of these warnings contact the Customer Care Department m Installation Any installation work must be undertaken by a qualified electrician or a competent person This hood must be installed in accordance with the installation instructions and all measurements must be adhered to If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS 6172 BS 5440 and BS 6891 Natural Gas and BS 5482 LP Gas 1994 the Gas Safety Installation amp Use Regulations the Building Regulations issued by the Department of the Environment the Building standards Scotland Consolidated Regulations issued by the Scottish Development Department The fan motor of this cooker hood incorporates a cut out device which will operate if the cooker hood is installed below the min
10. e is in addition to your statutory and legal rights ZANUSSI EUROPEAN GUARANTEE If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased your product e The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e This guarantee relates to you and cannot be transferred to another user e Your new home is within the European Community EC or European Free Trade Area e The product is installed and used in accordance with our instructions and is only used domestically i e a normal household Before you move please contact your nearest Customer Care Centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 29 99 Germany Nurnberg 49 0 911 323 2600 0 0 Italy Pordenone 39 0 167 3 Sweden Stockholm 46 0 8 73 0 UK Slough ne zn zn _ A m gt nt gt INSTALLATION INSTRUCTIONS IN It is dangerous to alter the specifications or attempt to modify this product in any way Technical Information DIMENSIONS HEIGHT 35 cm WIDTH 60 cm DEPTH 27 36 cm DEPTH WITH VISOR OPEN 54 63 cm WEIGHT GROSS 13 0 kg NET 11 0 kg ELECTRICA
11. elow the cooker hood exceeds the maximum outputs quoted please refer to the cooker manufacturer s installation instructions 11 Clearance Height gt 50 mm A clearance height of 650mm 25 1 2 is required when installed above a built in electric hob or 700mm 27 1 2 when installed above a built in gas hob A clearance height of 685mm 27 is required when ABCD installed above a slot in electric cooker or 787mm 30 450 mm min 1 2 when installed above a slot in gas cooker Hob When installed between adjoining wall cabinets the wall cabinets must not overhang the hob and the distance between the A Built in Electric Hob 650mm clearance underside of the cabinet and the worktop must B Built in Gas hob 700mm clearance be 450mm If the height of the wall cabinet is C Slot in Electric Cooker 685mm clearance less than 450mm a gap of 50mm must be D Slot in Gas Cooker 787mm clearance maintained either side of the hob This cooker hood must not be installed above a cooking appliance with a high level grill Unpacking The fittings supplied to install this cooker hood can be found with the instruction book inside the packaging The fixing kit comprises 2 Wall fixing brackets 6 Decor panel fixing screws 4 Security fixing screws ES Fitting the Wall Brackets 1 Use the paper template provided to mark the hole positions on the wall for the bracket fixing screws not supplied 2
12. ically routed to the Service Force centre covering your post code area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you read the details under the heading Something not working When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and serial number found on the rating plate 5 The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in guarantee service calls For Customer Service in Ireland please contact us at the address below Zanussi Electrolux Group Irl Ltd Long Mile Road Dublin 12 Republic of Ireland Tel 353 0 1 4090751 Email service eid electrolux ie Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www zanussi co uk for training purposes 16 Dir 89 336 CEE ae 73 23 CEE O Electrolux pl 436002545 01 041222
13. imum height recommended under section Clearance Height or if the motor becomes overheated If the cut out device is activated switch off the fan motor and allow the cooker hood to cool The cut out device will reset itself when the fan motor has cooled significantly It is dangerous to alter the specifications or modify this product in any way When installed between adjoining wall cabinets the wall cabinets must not overhang the hob If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose Do not install above a cooker with a high level grill Child Safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the appliance During Use This product is for domestic use only Never leave frying pans unattended during use as over heated fats and oils might catch fire Never do flamb cooking under this cooker hood Do not leave naked flames under the hood Maintenance and Service This appliance can be a hazard if the synthetic paper and charcoal filters are not replaced as recommended
14. o dampness after manufacture 4 Use the 6 x 15mm 1 2 ins round headed screws provided to attach the decor panel to the hood visor LS To Refit the Hood with Decor Panel Attached la Insert the upper visor guides into the upper track in the front of the casing 2 Hinge down the bottom edge of the visor and insert the lower guides into the track in the bottom of the casing 3 Push the visor in until an audible click is heard 4 The visor can now be opened and closed in its normal function Adjustment If a heavy door is fitted or if the visor will not stay closed it may be necessary to make an adjustment to the closing mechanism of the visor Insert a small flat bladed screw driver through the hole the friction assembly on either side of the casing indicated by the letter V and turn clockwise to apply pressure on the guide ui E Both friction assemblies should be adjusted ey by the same amount to ensure the visor opens smoothly AAA MA Care should be taken when removing the visor with the decor panel for cleaning or servicing as the visor is now extremely heavy and should it be dropped it could damage the appliance beneath and adjoining work surfaces 15 Service and Spare Parts In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning 08705 929929 Your telephone call will be automat
15. or any part there of is proved to be defective by reason only of faulty workmanship or materials the company will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that e The appliance has been correctly installed and used only on the electrical supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s operating and maintenance instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All service work under this guarantee must be undertaken by Zanussi Service Force Centre e Any appliance or defective part replaced shall become the property of this company Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged EXCLUSIONS This Guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any lilght bulbs or removable parts of glass or plastic e Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United Kingdom e Appliances found to be in use within a commercial environment plus those which are the subject of rental agreements e Products of Zanussi manufacture which are not marked by Zanussi Ltd This guarante
16. ver heated fats and oils can catch fire Do not leave naked flames under the cooker hood Ensure the visor is open when using the hob even if the fan on the hood is not switched on Ensure heating areas on your hob are covered with pots and pans when using the hob and cooker hood simultaneously Recirculation Mode MAINTENANCE AND CLEANING N Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply The cooker hood must be kept clean as a build up of grease or fat can be a fire hazard External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent N Always wear protective gloves when cleaning the hood Never use scouring pads or abrasive cleaners Never use excessive amounts of water when cleaning particularly around the control panel Synthetic Paper Grease Filter The filter has saturation indicators which are small squares made from a series of dots When the white paper inside the squares becomes saturated with grease the coloured dots start to run and spread across the paper indicating that the filter has reached saturation point and must be replaced ES To replace the synthetic paper grease filter 1 Open the visor 2 Press inwardly on the two slide catches and lower the grille to the stop position Raise the front edge of the grille through a 45 angle until it detaches itself from the guides 3 Carefully ease out the met
Download Pdf Manuals
Related Search