Zanussi ZHC 951 Instruction Manual
Contents
1. ZANUSSI Thank you for buying a Zanussi product To enable you to use your appliance effectively and safely please read this instruction book carefully before using the appliance and retain for future reference If you require guidance in the use of the appliance or require further information on Zanussi Products please contact our Customer Care Department at the address below or visit our website at www zanussi co uk Customer Care Department Zanussi 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 727 727 calls to this number may be recorded for traing purposes To register ownership please ensure you complete and return the guarantee card supplied with the appliance For the User Important Safety Information Your Appliance Operating Instructions Cooker Hood Controls To Operate Recirculation Extraction Maintenance and Cleaning External Cleaning Metal Grease Filters Charcoal Filters To Remove Replace the Charcoal Filters Changing the Light Bulb Something Not Working Service and Spare Parts Guarantee Conditions For the Installer Technical Information Electrical Connection Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Unpacking Clearance Heights Fitting the Wall Brackets Fitting the Canopy Hood Venting Recirculation Fitting the Chimney Stack To register ownership please ensure you complete and return the2. is ducted to the outside the charcoal filter must be removed 3 Ducting Connection Connect the ducting chosen to the 150mm ducting spigot on top of the motor housing or the 150 120mm ducting spigot 9 and secure using the jubilee clips 25 A 120 125mm collar 10 is provided to fit over the 120mm ducting spigot when 125mm ducting is fitted If the room where the cooker hood is to AN be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room The cooker ducting extraction mode must never be connected to central heating flues radiators or water heaters etc 13 Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted In the recirculation mode contaminated air is passed through the charcoal filter to be purified and recirculated into the kitchen through the grille outlets on either side of the chimney gt Recirculation Connection Assemble the two halves of the round recirculation extension duct 14 Push fit the assembled extesion duct 14 on to 150mm ducting spigot on top of the motor housing Push fit the recirculation spigot 15 onto the other end of the extension duct 14 Insert the extension ducts item
3. 14 1 into either side of the recirculation spigot 14 ensuring the connections are vertically and horizontally aligned with the outlets in the chimney Chimney Stack The chimney consists of two sections The lower chimney measures 740mm with the recirculation grilles on either side and the upper chimney measures 215mm The overall installed measurement is min 740 940mm max paz Fitting the Chimney Position the upper chimney section 2 1 and fix the chimney to the upper frame using two 2 9x9 5mm screws 12c Slide the lower chimney section 2 2 up over the upper chimney and fix the chimny to the lower frame using two 2 9x9 5mm screws 12c When installed in the recirculation mode the ducting outlet extension pieces 14 1 should align with the rectangular holes in each side of the chimney Position the recirculation grilles 8a and 8b so the slats face in a forwards and upwards direction 25 Fitting the Hood Body 1 Before fixing the hood body to the frame Remove the grease filters from the hood body Remove the activated charcoal filter Using the four M6x10 12f fix the hood body 1 to the frame 7 1b IS Electrical Connection Push fit the Cmd connecter on the cable from the motor housing to the one from the control box Place the Cmd connector in the junction box 24 and clamp it together using two 2 9x6 5mm screws 12e Fix the junction box 24 to the
4. If the cut out device is activated switch off the fan motor and allow the cooker hood to cool The cut out device will reset itself when the fan motor has cooled significantly e It is dangerous to alter the specifications or modify this product in any way e When installed between adjoining wall cabinets the wall cabinets must not overhang the hob e If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type e If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose Do not install above a cooker with a high level grill Child Safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the appliance During Use This product is for domestic use only Never leave frying pans unattended during use as overheated fats and oils might catch fire Never do flamb cooking under this cooker hood Do not leave naked flames under the cooker hood Maintenance and Service This appliance can be a hazard if the grease filters and charcoal filters are not cleaned and replaced as recommended Under no circumstances should you attempt to repair the appliance yourself Repai
5. ce B Built in Gas hob 700mm minimum clearance C Slot in Electric Cooker 685mm minimum clearance D Slot in Gas Cooker 787mm minimum clearance 2s Drilling the Ceiling Support Shelf Using a plumb line mark the centre point of the hob on the ceiling or support shelf Position the drilling template item 21 on the ceiling or support shelf ensuring the template is aligned correctly with the angles of the hob Mark the hole centres Pilot drill the fixing holes at the points marked for the approprate size rawl plugs and screws not supplied lt will also be necessary to drill a 10mm hole for the mains cable and the ducting if the hood is to be installed ducted to the outside f Fixing the Frame IMPORTANT Before fixing separate the Upper Chimney section 2 1 and the Lower Chimney section 2 2 from the frame by removing the screws 12c Then separate the two sections of the F frame by unscrewing the 8 screws U located on each side of the frame Upper Frame Feed the mains cable through the frame and the hole in the ceiling or support shelf Fix the Upper Frame 7 1a to the ceiling screws not supplied Lower Frame Fix the lower frame using the 8 screws removed earlier and adjust the length according to the installation height the minimum distance before fitting the hood body 1 must be 710mm W
6. e to incorrect installation of the cooker hood or if the hood is not installed in compliance with relevant regulations controlling this type of installation Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications If the output of the appliance below the cooker hood exceeds the maximum outputs quoted please refer to the cooker manufacturer s installation instructions A minimum clearance height of 650mm 252ins is required when installed above a built in electric hob or 700mm 27 2ins when installed above a built in gas hob A minimum clearance height of 685mm 27ins is required when installing above a slot in electric cooker or 787mm 30 2ins when installed above a slot in cooker When installed between adjoining wall cabinets the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mmm 1734ins a gap of 50mm 2ins must be maintained either side of the hob This cooker hood must not be installed above a cooking appliance with a high level grill The hood can be installed above these heights but for optimum performance it should be installed at the distances quoted for the appropriate heat source 450 mm min en ee Hob A Built in Electric Hob 650mm minimum clearan
7. ed domestically i e a normal household Before you move please contact your nearest Customer Care Centre listed below to give them detailsof your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 22 22 Germany Nurnberg 49 0 911 323 2600 Italy Pordenone 39 0 1678 47053 Sweden Stockholm 46 0 20 78 77 50 United Kingdom Slough 44 0 1753 219897 8 INSTALLATION INSTRUCTIONS AN It is dangerous to alter the specifications or attempt to modify this product in any way Technical information DIMENSIONS HEIGHT OF CANOPY incl glass visor 46mm HEIGHT OF CHIMNEY UPPER SECTION 215mm LOWER SECTION 740mm WIDTH OF CANOPY incl glass visor 898mm DEPTHOF CANOPY incl glass visor 700mm ELECTRICAL SUPPLY VOLTAGE 50HZz 230V POWER CONSUMPTION 230W FAN MOTOR 150W LAMPS 4x20W 80W SUITABLE FOR INSTALLATION ABOVE ELECTRIC HOB 7KW MAX GAS HOB 10KW MAX SLOT IN ELECTRIC COOKER SLOT IN GAS COOKER Ly DOUBLE INSULATED DO NOT EARTH Electrical Requirements Any permanent electrical installation must comply with the latest E E Regulations and local Electricity Board regulations For your own safety this should be undertaken by a qualified electrician e g your local Electricity Board or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contract
8. guarantee card supplied with the appliance Guide to use the instruction book The following Symbols will be found in the text to guide you through the instruction book AN Safety instructions DZ Step by step instructions IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of safety Ensure that you understand them all before installing or using this appliance Your safety is of paramount importance If you are unsure about any of the meanings of these warnings contact the Customer Care Department e Installation e Any installation work must be undertaken by a qualified electrician or a competent person e This hood must be installed in accordance with the installation instructions and all measurements must be adhered to e Ifthe cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS 61 72 BS 5440 and BS 6891 Natural Gas and BS 5482 LP Gas 1994 the Gas Safety Installation amp Use Regulations the Building Regulations issued by the Department of the Environment the Building Standards Scotland Consolidated Regulations issued by the Scottish Development Department e The fan motor of this cooker hood incorporates a cut out device which will operate if the cooker hood is installed below the minimum height recommended under the section Clearance Height or if the motor becomes overheated
9. h your appliance or for contact your local Service Force Centre by further information on Zanussi products please telephoning contact our Customer Care Department at the address below or visit our website at 08705 929929 www zanussi co uk Your telephone call will be routed to your local Customer Care Department Service Force Centre Zanussi 55 77 High Street For the address of your local Service Force Slough Centre and further information about Service Berkshire Force please visit the website at SL1 1DZ www serviceforce co uk Telephone 08705 727 727 calls to this number may be recorded for training purposes 7 GUARANTEE CONDITIONS We Zanussi undertake that if within twenty four months of the date of the purchase this Electrolux built in product or any part thereof is proved to be defective by reason only of faulty workmanship or materials the company will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that e The appliance has been correctly installed and used only on the electrical supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturers operating and maintenance instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All service work under this guarantee must be undertaken by a Zanussi Serv
10. hen the hood is to be installed in the recirculation mode position the frame in the direction you want the recirculated air to pass into the kitchen The frame mountings must be secure enough to withstand the weight of the cooker hood and any knocks the hood may get through normal ware and tear 12 On completion check that the base is stable even ff the frame is subject to movement AN The installer must provide ample support where the ceiling or support shelf is not strong enough by installing cross beams over the joists or above the shelf to ensure the frame is quite rigid at its mounting point Extraction The cooker hood is more effective when used in the extraction mode ducted to the outside Venting kits may be purchased through your retailer or DIY store and must be ducted to an outside vent of 125mm 5 or 8150mm 6 For the best performance use the shortest possible duct run and the minimum number of bends Where flexible ducting is fitted it should not be turned through very tight bends as this may impair the performance of the hood It is recommended a maximum length of 3 metres with one bend to be installed to be reduced metre for each 900 bend If a distance is greater than 3 metres the efficiency of the hood could be impaired The ducting used must be manufactured from fire retardent material conforming to the relevant British Standard or DIN 4102 B1 When the cooker hood
11. hood body 1 using the two 2 9x9 5mm screws 12c Working Test When the electrical connection has been made test the three speed fan and worktop illumination 15 Dir 89 336 CEE 73 23 CEE Electrolux ple 2002 436001739 01 030415
12. ice Force Centre e Any appliance or defective part replaced shall become the property of this company Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged EXCLUSIONS This Guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replacement of any lamps or removable parts of glass or plastic e Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United Kingdom e Appliances found to be in use within a commercial environment plus those which are the subject of rental agreements e Products of Zanussi manufacture which are not marked by Zanussi This guarantee is in addition to your statutory and legal rights ZANUSSI EUROPEAN GUARANTEE If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased the product e The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e This guarantee relates to you and cannot be transferred to another user e Your new home is within the European Community EC or European Free Trade Area e The product is installed and used in accordance with our instructions and is only us
13. ing NICEIC Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker 12 4KW MAX 13 5KW MAX Note CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89 336 Electromagnetic compatibility and subsequent modifications and Low Votage directive This appliance is fitted with a 2 core mains cable and must be permanently connected to the electricity supply via a double pole switch having 3mm minimum contact gap on each pole A Switched Fuse Connection Unit to BS 1363 Part 4 fitted with a 3 Amp fuse is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions This appliance conforms to BS 800 1988 and EEC Directive No 78 308 regarding suppression of radio and television interference INSTALLING THE COOKER HOOD Unpacking The hood is supplied with the following components for installation as illustrated Item Qty Description 1 1 Hood body complete with Controls lighting blower and filters 2 1 Telescopic chimney comprising 2 1 1 Upper section 2 2 1 Lower section 7 1 1 Telescopic frame complete with extractor consisting of 7 1a 1 Upper frame 7 1b 1 Lower frame 8a 1 Right hand air outlet grille 8b 1 Left hand air outlet grille 9a 1 120 125mm Ducting collar 9b 1 150 120m
14. ly seated into the lamp holder If lamp failure has occurred then it should be replaced with a 12V 20W M262 halogen spot lamp Replacement filters and lamps can be obtained from your local Service Force Centre SOMETHING NOT WORKING If having followed these instructions carefully your cooker hood fails to work properly please carry out the following checks he cooker hood will not start Check the hood is connected to the electricity supply Make sure the switch is in the ON position The fan speed is set high enough for the task The grease filter is clean The kitchen is adequately vented to allow the entry of fresh air If set up for recirculation check that the charcoal filter is still effective If set up for extraction check that the ducting outlets are not blocked he cooker hood has switched off during operation The safety cut out device has been tripped Turn off the hob and then wait for the device to reset If after all these checks the fault persists In guarantee customers should ensure that contact your local Service Force Centre quoting the above checks have been made as the the model and serial number engineer will make a charge if the fault is not a a mechanical or electrical breakdown Please note that it will be necessary to provide proof of purchase for any in guarantee service calls SERVICE AND SPARE PARTS If you require an engineer or spare parts For general assistance wit
15. m Ducting spigot 14 1 Recirculation extension ducting 14 1 2 Recirculation extension ducting 15 1 Recirculation spigot 24 1 Junction box 25 2 Jubilee Clips Item Qty Installation Components 12c 6 2 9 x9 5mm Chimney fixing screws 12e 2 2 9 x6 5mm Junction box fixing screws 12f 4 M6x10mm Hood body fixing screws 12g 4 M6x80mm Lower frame fixing screws 12h 4 5 2x70mm Upper frame fixing screws 21 1 Ceiling drilling template Item Qty Documents 1 Instruction Manual bises tt mit oS A 0 2i 22 8b 0 8a 12e 24 12c 0 E ae Se eer T Gum 10 Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown All installations must comply with the local AN authorities requirements for the discharge of exhaust air Incorrect installation may affect the safety of this cooker hood Installation Requirements Before installation check that the wall to which the cooker hood is to be fitted for electric cables water pipes and gas This cooker hood is designed to be fixed to any vertical surface over a cooking area and can be used in the extraction ducted to the outside or recirculation mode The installation work must be undertaken by a qualified and competent person The manufacturer disclaims any responsibility for damage du
16. ntaminated air enters the cooker hood passing through the grease filters and is passed out through the ducting into the atmosphere To obtain the best performance when cooking it is advisable to switch the cooker hood on for a few minutes before you start cooking and leave it running for about 15 minutes after finishing When used in the extraction mode the AN charcoal filters are not required Never do flamb cooking under this cooker hood Never leave frying pans unattended during use as overheated fats and oils can catch fire Do not leave naked flames under the cooker hood Ensure heating areas on your hob are covered with pots and pans when using the hob and cooker hood simultaneously MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply The cooker hood must be kept clean as a build up of grease or fat can be a fire hazard External Cleaning Wipe the cooker hood frequenily with warm soapy water using a mild detergent Never use scouring pads or abrasive cleaners Never use excessive amounts of water when cleaning particularly around the control panel Metal Grease Filters The grease filters absorb grease and dust during cooking to help keep the cooker hood clean inside aT Cleaning The filters must be washed once every month using a normal household detergent their compact dimension also enables them to be washed in a di
17. rs carried out by inexperienced persons may cause injury or more serious malfunction Refer to your local Zanussi Service Force Centre Always insist on genuine spare parts YOUR APPLIANCE ee K MIN 740 MAX 940 740 OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen it will not extract steam Cooker Hood Controls The cooker hood functions are controlled by four push button switches located centrally in the control fascia L Turns the worktop lighting On and Off S Mains light illumination indicates fan w the fan motor On and Of at ow 9094 7 SE EM speed suitable for one pan or when simmering V2 Medium fan speed suitable for use 3 3 when cooking with a number of pots and pans S V1 V2 V3 V3 Maximum fan speed suitable for cooking foods with strong odours To Operate Select the required fan speed and light if required The appliance can be installed to recirculate or extract contaminated air The cooker hood is more effective when used in the extraction mode Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted In the recirculation mode the contaminated air is passed through the charcoal filters to be purified and recirculated into the kitchen through the recirculation grilles in either side of the chimney stack Extraction In the extraction mode the co
18. shwasher Allow to dry completely before replacing Removing and replacing the filters Remove the filters one at a time press against the metal actuator to release the spring catch as illustrated When replacing ensure that the handles face outwards Charcoal Filter In the recirculation mode the charcoal filter absorbs smells and unwanted odours _ fh EN The charcoal filter cannot be cleaned or regenerated and must be replaced approximately every 4 months or more frequently if the hood is subjected to heavy usage lt 5 Replacing the charcoal filter First remove the metal grease filters Remove the saturated activated charcoal filter by releasing the fixing hooks as illustrated Position the new charcoal filter in the position marked and while holding the filter replace the fixing hooks as illustrated This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended iS Changing the Spot Lamps Remove the two screws fixing the lighting support Remove the spot lamp from the holder by pulling the lamp downwards Replace the spot lamp by inserting the two pins at the base of the lamp into the holes in holder and pushing into position Replace the lighting support ensuring it is located correctly and fix back into position using the two screws If one of the spot lamps has failed to function check that the lamp is ful
Download Pdf Manuals
Related Search