Home

Zanussi ZERC 3025 X Instruction Manual

image

Contents

1. SOMETHING NOT WORKING If the appliance is not working correctly please carry out the following checks before contacting your local Service Force Centre Symptom No power to the appliance The light does not come on The temperature in the fridge The compressor runs continously Noise Water under the salad crispers Solution Check there is power at the socket Check there is not a power cut by checking the household lights Check the fuse has not blown Ensure that the bulb is correctly fitted Replace the bulb if it has blown Check the door light switch is not jammed Check the thermostat control knob in the fridge is turned to the correct setting relative to ambient conditions Check the ambient temperature is within the appliance s operating limits please refer to the installation section in this instruction book Relocate the appliance if necessary Adjust the thermostat control knob to give correct temperature control See Setting the temperature Check that the door is closed Large quantities of food have recently been placed in the cabinet and or door is frequently opened Check that air ventilation is not obstructed Refer to normal operating sounds Check the drain hole is not blocked see Maintenance and Cleaning If after the above checks your appliance still does not operate correctly contact your local Service Force Centre Please note that it will be
2. 10 C to 32 C N 16 C to 32 C ST 18 C to 38 C T 18 C to 43 C It should be located in a dry atmosphere out of direct sunlight and away from extreme temperature e g not next to a boiler or radiator or in a very cold room e g an outhouse where the temperatures may fall below 10 C 50 F If these temperatures are exceeded i e colder or warmer then the appliance may not operate correctly You should also ensure that air can circulate freely around the back and the top of the cabinet There must also be at least 100 mm 4 distance between the top of the cabinet and any overhanging kitchen furniture A Ideally the appliance should not be positioned beneath overhanging furniture B There should also be a gap of 25 mm either side of the appliance Do not obstruct the space underneath The back of the cabinet may be placed close to the wall but must not touch it DO NOT install in places with restricted ventilation Adjust the level of the appliance by screwing out the adjustable foot or feet at the bottom of the cabinet using your fingers or a tool see figure Rear spacers In the bag with the documentation there are two spacers which must be fitted as shown in the figure Slacken the screws and insert the spacer under the screw head then re tighten the screws 12 Depending upon the position which you choose for your appliance you may wish to reverse the way in which the door opens To do th
3. cause substantial damage to the appliance and result in food loss DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice Under NO circumstances should solid ice be forced off the lining or shelves Solid ice should be allowed to thaw when defrosting the appliance See Defrost Instructions Maintenance and Cleaning e Switch off and unplug the appliance before carrying out any cleaning or maintenance work Servicing This product should be serviced by an authorised engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Refer to your local Service Force Centre and always insist on genuine spare parts At the end of the Appliance Life e When disposing of your appliance use an authorised disposal site Remove the plug and ensure that any locks or catches are removed to prevent young children being trapped inside CONTENTS Instructions for the User Important Safety Information Operation Before use Setting the temperature Fresh food refrigeration Normal operating sounds Movable shelves Positioning the door shelves Hints and Tips Maintenance and Cleaning Internal cleaning External cleaning When the appliance is not in use Changing the light bulb Defrosting Something Not Working Service and Spare Parts Customer Care Guarantee Condi
4. necessary to provide proof of purchase for any in guarantee service calls In guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown SERVICE AND SPARE PARTS sseaucesronce In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area For the address of your local Service Force Centre and further information about Service Force please visit the website at www serviceforce co uk For Customer Service in Ireland please contact us at the address below Zanussi Electrolux Electrolux Group Irl Ltd Long Mile Road Dublin 12 Republic of Ireland Telephone 353 0 1 4090751 Email service eid electrolux ie Before calling out an engineer please ensure you have read the details under the heading Something Not Working When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and serial number of the appliance found on the rating plate 5 The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in guarantee ser
5. the condenser black grill and the compressor at the back of the appliance with a brush or vacuum cleaner see figure When the appliance is not in use When the appliance is not in use for long periods disconnect from the electricity supply empty all foods and clean the appliance leaving the doors ajar to prevent unpleasant smells Changing the light bulb If it becomes necessary to replace the lamp press on the rear hook and at the same time slide the cover in the direction indicated by the arrow Unscrew the bulb and replace it with one of the same power the maximum power is shown on the light diffuser available from your nearest Service Force Centre Replace the light cover by sliding it into its original position Defrosting The refrigerator automatically defrosts every time the compressor stops The water is discharged via the pipe into a tray located at the back of the appliance above the compressor where it evaporates A Important To avoid defrost water overflowing into the fridge periodically clean the water discharge hole in the centre of the V shaped drip collector at the back of the refrigerator compartment behind the salad crispers Use the defrost cleaner provided which you will find already inserted into the discharge hole Remember to wash the defrost cleaner in hot soapy water at regular intervals Dry throughly before replacing
6. to allow the refrigerant to settle Child Safety e e Do not allow children to tamper with the controls or play with the product Keep all packaging well away from children General Safety This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorized technicians Take utmost care when handling your appliance so as not to cause any damages to the cooling unit with consequent possible fluid leakages The appliance must not be located close to cookers radiators or boilers Avoid prolonged exposure of the appliance to direct sunlight Do not use other electrical appliances such as ice cream makers inside of refrigerating appliances During Use e This appliance is designed for domestic use only specifically for the storage of edible foodstuffs e Frozen food must NOT be re frozen once it has thawed out Do not place carbonated or fizzy drinks in the freezer Do not remove items from the freezer if your hands are damp wet as this could cause skin abrasions or frost freezer burns e Ice lollies can cause frost freezer burns if consumed straight from the freezer Manufacturers storage recommendations should be strictly adhered to Refer to relevant instructions The cooling plate or refrigerated freezer shelves in this appliance contain channels through which the refrigerant passes If these are punctured this will
7. to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow Connect the blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black Connect the brown live wire to the terminal in the plug which is marked with the letter L or coloured red The plug moulded onto the lead incorporates a fuse For replacement use a 13amp BSI362 fuse Only ASTA or BSI approved fuses should be used The plug must not be used if the fuse cover carrier is lost The cover carrier is indicated by the coloured insert at the base of the plug A replacement cover carrier must be obtained from your local Service Force Centre This appliance complies with the E E C Directive No 87 308 of 2 6 87 relative to radio interference suppression E E C Directives 73 23 EEC of 19 2 73 Low Voltage Directive and subsequent modifications 89 336 EEC of 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications This appliance complies with the following 13 Door reversal directions 1 Disconnect from the electricity supply 2 Gently lay the fridge on its back with the top held away from the floor by 5 8 cm 2 3 inches of packing 3 Remove the ventilation grill D 4 remove the bottom hinge E by unscrewing its three fixing screws 5 Slide out the fridge door from pin G unscrew the latter and then ref
8. ZANUSSI EK Electrolux REFRIGERATOR ZERC 3025 ZERC 3025 X INSTRUCTION BOOKLET IMPORTANT SAFETY INFORMATION It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information This information has been provided in the interest of safety You MUST read it carefully before installing or using the appliance Installation e This appliance is heavy Care should be taken when moving it It is dangerous to alter the specifications or attempt to modify this product in any way Care must be taken to ensure that the appliance does not stand on the electrical supply cable Important if the supply cable is damaged it must be replaced by a special cable available from your local Service Force Centre Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Parts which heat up should not be exposed Whenever possible the back of the appliance should be close to a wall but leaving the required distance for ventilation as stated in the installation instructions The appliance should be left for 2 hours after installation before it is turned on in order
9. appliance are not obstructed e Always leave warm food to cool down to room temperature before placing in the fridge e Try to avoid keeping the door open for long periods or opening the door too frequently as warm air will enter the cabinet and cause the compressor to switch on unnecessarily often e Ensure there are no obstructions preventing the door from closing properly e Itis advisable to peridocally clean the refrigeration system at the back of the appliance with a duster or vacuum cleaner MAINTENANCE AND CLEANING Before any maintenance or cleaning work is carried out DISCONNECT the appliance from the ELECTRICITY supply Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda 5ml to 0 5 litre of water Rinse and dry thoroughly A NEVER USE DETERGENTS ABRASIVE POWDERS HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND LEAVE A STRONG ODOUR External cleaning Many proprietary kitchen surface cleaners contain chemicals that can attack damage the plastics used in this appliance For this reason it is recommended that the outer casing of this appliance is only cleaned with warm water with a little washing up liquid added An accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption You MUST ensure that the appliance is switched OFF Once or twice a year dust
10. ashing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world
11. ccount regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 29 29 Germany Nurnberg 49 0 800 234 7378 Italy Pordenone 39 0 0434 39 4700 Sweden Stockholm 46 0 8 672 53 90 UK Slough 44 0 1753 219 897 Ireland Dublin 353 0 1 4090751 10 TECHNICAL SPECIFICATIONS DIMENSIONS Height 160 cm Width 60 cm Depth 62 5 cm POWER SUPPLY VOLTAGE AND FREQUENCY 220 240 V 50 Hz TOTAL POWER ABSORBED 110W AVERAGE DAILY UNITS ELECTRICITY 0 162 kWh GROSS CAPACITY 294 NET CAPACITY 291 This figure is based on standard test results in accordance with European Standard EN 153 Actual consumption will depend on how the appliance is used and where it is located INSTALLATION A Important IF YOU ARE DISCARDING AN OLD APPLIANCE THAT HAS A LOCK OR CATCH ON THE DOOR YOU MUST ENSURE THAT IT IS MADE UNUSABLE TO PREVENT YOUNG CHILDREN BEING TRAPPED INSIDE Positioning This appliance should only be installed at a location where the ambient temperature corresponds to the climate classification indicated on the rating plate which is located at the left on the inside of the appliance The following table shows which ambient temperature is correct for each climate classification SN
12. is refer to instructions on Door reversal Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown Important It must be possible to disconnect the appliance from the mains power supply the plug must therefore be easily accessible after installation D200 A Electrical connections Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person WARNING THIS APPLIANCE MUST BE EARTHED The manufacturer declines any liability should this safety measure not be observed If the plug that is fitted to your appliance is not suitable for your socket outlet it must be cut off and the appropriate plug fitted Remove the fuse from the cut off plug The cut off plug should then be disposed of to prevent the hazard of shocks in case it should be plugged into a 13amp socket in another part of your home A Important The wires in the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live If you fit your own plug the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug proceed as follows GREEN amp YELLOW 13 AMP FUSE Connect the Green and Yellow earth wire
13. it it on the opposite side 6 remove the two plugs of the door where available discovering the holes for the hinge pins assemble them on the opposite side 7 reassemble the door 8 using a 10 mm spanner unscrew the hinge pin E and reassemble it on the opposite side of the hinge 9 reassemble the lower hinge E on the opposite side using the screws previously removed Slide the hole cover F out of the ventilation grille D by pushing it in the direction of the arrow and reassemble it on the opposite side 10 refit the ventilation grille D clipping it into place 11 Unscrew the handle Refit it on the opposite side after having pierced the plugs with a punch Cover the holes left open with the plugs supplied in the documentation pack A Important After completion of the door reversing operation check that the door gasket adheres to the cabinet If the ambient temperature is cold i e in Winter the gasket may not fit perfectly to the cabinet In that case wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdryer on a low setting 14 Printed on recycled paper Electrolux plc 2005 Eq from the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators Cookers w
14. ompartment depends on the following factors room temperature how often the door is opened how much food is stored position of the appliance 4 A Important During prolonged periods of abnormally hot weather if the thermostat is set on too high a number the cooling system may operate continuously and the fridge cooling plate may not defrost Turning the knob to a lower number will cause the automatic defrosting to resume Fresh food refrigeration To obtain the best performance do not store warm food or evaporating liquids in the refrigerator do cover or wrap the food particularly if it has a strong flavour Do not cover the shelves with any protective material such as paper cardboard or plastic which may obstruct the air circulation through them To help you use your refrigerator correctly here are some more useful hints Raw meat beef pork lamb amp poultry or chicken wrap in polythene bags and place on the glass shelf above the salad crispers Meat can only be stored safely in this way for one or two days at the most Fruit amp vegetables these should be thoroughly cleaned and placed in the bottom salad crisper s Butter amp cheese these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible Milk bottles these should have a cap and should be stored in the bottle rack on the door Normal Operating So
15. other legal rights Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the European Community EC or European Free Trade Area e Appliances found to be in use within a commercial environment plus those which are subject to rental agreemenis Products of Zanussi Electrolux manufacture which are not marketed by Zanussi Electrolux European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased your product The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e This guarantee relates to you and cannot be transferred to another user Your new home is within the European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically i e a normal household The product is installed taking into a
16. tions N O aooaa A A A A NN DD DD OD 10 Instructions for the Installer Technical Specification Installation Positioning Rear Spacers Electrical Connection Door Reversal 12 12 12 13 OPERATION Before using Remove all securing tapes Wash inside the appliance with lukewarm water and bicarbonate of soda 5 ml to 0 5 litre of water Control panel Do not use soap or detergent as the smell may linger Dry thoroughly A Pilot light B Thermostat control To Start the Appliance Allow the appliance to stand for 2 hours after installation Plug in the appliance and switch on at the mains supply Turn the thermostat control knob B to a medium setting The pilot light A will illuminate Leave the appliance for approximately 4 hours to allow the correct temperature to be reached before placing food inside To switch off the appliance turn the thermostat control knob to position O Setting the temperature The temperature within the appliance is controlled by the thermostat control knob situated at the top of the appliance To operate the appliance proceed as follows Turn the thermostat control beyond the m position Position min minimum coldness Position max maximum coldness Turn the thermostat dial to the required position The intermediate position is usually the most suitable The thermostat setting can vary as the temperature inside the refrigeration c
17. unds You may hear faint gurgling or bubbling sounds when the refrigerant is pumped through the coils or tubing at the rear to the cooling plate evaporator When the compressor is on the refrigerant is being pumped round and you will hear a whirring sound or pulsating noise from the compressor e A thermostat controls the compressor and you will hear a faint click when the thermostat cuts in and out Movable shelves The walls of the refrigerator have runners so that shelves can be positioned as desired Positioning the door shelves To permit storage of food packages of various sizes the door shelves can be adjusted in height To do this proceed as shown in the diagram 4 HINTS AND TIPS Food Storage To obtain the best results from the appliance neither hot foods nor liquids which may evaporate should be placed in the larder compartment Keep the time between buying chilled food and placing it in your refrigerator as short as possible Do not push food together too much try to allow air to circulate around each item e Do not store food uncovered Remove suspect food from your refrigerator and clean refer to Maintenance and Cleaning Y Energy Saving Advice Do not install the appliance close to sources of heat such as a boiler or radiator e Locate the appliance in a cool well ventilated room and make sure that the air openings of the
18. vice calls CUSTOMER CARE DEPARTMENT For general enquiries concerning your Zanussi Electrolux appliance or for further information on Zanussi Electrolux products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www zanussi electrolux co uk Customer Care Department Zanussi Electrolux 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 727 727 calls to this number may be recorded for training purposes GUARANTEE CONDITIONS Standard guarantee conditions We Zanussi Electrolux undertake that if within 12 months of the date of the purchase this ZANUSSI ELECTROLUX appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the electricity supply stated on the rating plate The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All service work under this guarantee must be undertaken by a Service Force Centre Any appliance or defective part replaced shall become the Company s property This guarantee is in addition to your statutory and

Download Pdf Manuals

image

Related Search

Related Contents

Samsung <span style="unicode-bidi: embed;">WF1702WEC מכונת כביסה פתח קידמי 7 ק"ג בטכנולוגיית ecobubble™</span> מדריך למשתמש  Immagine - Camperpress  ナックルバイザ - Shopatron  Eos X Terminal user`s manual  M68ICS08SOM User`s Manual  AKG198 Montage- und Bedienungsanleitung  

Copyright © All rights reserved.
Failed to retrieve file