Zanussi CH 250 Instruction Manual
Contents
1. o ZANUSSI Thank you for buying a Zanussi product To enable you to use your appliance effectively and safely please read this instruction book carefully before using the appliance and retain for future reference If you require guidance in the use of the appliance or require further information on Zanussi Products please contact our Customer Care Department For general enquiries concerning your Zanussi appliance or for further information visit our website at http www zanussi co uk Customer Care Department Zanussi Limited Zanussi House Hambridge Road Newbury Berkshire Tel 01635 521 313 RG14 5EP Fax 01635 42970 To register ownership please ensure you complete and return the guarantee card supplied with the appliance For the User Important Safety Information Your Appliance Operating Instructions Cooker Hood Controls To Operate Recirculation Extraction Maintenance and Cleaning External Cleaning Charcoal Filters To Remove Replace the Charcoal Filter Synthetic Paper Grease Filter To Replace the Paper Grease Filter Changing the Light Bulb Something Not Working Service and Spare Parts For the Installer Installation Instructions Technical Information Electrical Connections Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Ducting Clearance Height Unpacking Fitting the Wall Brackets Venting To Fit the Ducting To Remove the Charcoal2. 2 Carefully remove the screw from the centre of the charcoal filter while holding the filter securely 3 Clean the metal inlet grille and motor support before replacing the charcoal filter Synthetic Paper Grease Filter The filter has saturation indicators which are small squares made from a series of dots When the white paper inside the squares becomes saturated with grease the coloured dots start to run and spread across the paper indicating that the filter has reached saturation point and must be replaced The synthetic paper grease filter cannot be cleaned It must not be washed ES To Replace the Synthetic Paper Grease Filter is Open the glass visor 2 Press inwardly on the two slide catches and the grille will open from the front 3 Slide the right edge of the grille forward until it clears the guide and then unhook the left hinge pin 4 Carefully ease out the metal wire retaining clips D Clean the metal grille and clips before replacing the filter Handle the wire clips with care and keep away A from children as they have sharp points This appliance can be a fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended Changing the Light Bulb If a lamp fails to function check that the bulb is screwed into the holder If bulb failure has occurred then it should be replaced with a 220 240V 40W clear cylindrical shape bulb with a small E14 screw thread A ree
3. Filter Recirculation Wall Cabinet Fitting Fitting the Cooker Hood to the Wall Levelling Peace of Mind for Twenty Four Months Standard Guarantee Conditions Guide to use the instruction book The following Symbols will be found in the text to guide you through the instruction book TS Step by step instructions A Safety instructions IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety Ensure that you understand them all before installing or using this appliance Your safety is of paramount importance If you are unsure about any of the meanings of these warnings contact the Customer Care Department Installation Any installation work must be undertaken by a qualified electrician or a competent person This hood must be installed in accordance with the installation instructions and all measurements must be adhered to If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS 6172 BS 5440 and BS 6891 Natural Gas and BS 5482 LP Gas 1994 the Gas Safety Installation amp Use Regulations the Building Regulations issued by the Department of the Environment the Building standards Scotland Consolidated Regulations issued by the Scottish Development Department The fan motor of this cooker hood incorporates a cut out device which will operate if the cooker hood is installed bel
4. Mn SOMETHING NOT WORKING If having followed these instructions carefully your cooker hood fails to work properly please carry out the following checks Symptom The cooker hood will not start The cooker hood is not working effectively The cooker hood has switched off during operation If after all these checks the problem persists contact your local Service Force Centre quoting the model and serial number Please note that it will be necessary to provide proof of purchase for any in guarantee service calls Check the hood is connected to the electricity supply Check that the fan speed control is set to 1 2 or 3 The fan speed is set high enough for the task The grease filter is clean The kitchen is adequately vented to allow the entry of fresh air If set up for recirculation check that the charcoal filter is still effective If set up for extraction check that the ducting and outlets are not blocked The safety cut out device has been tripped Tum off the hob and then wait for the device to reset In guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown SERVICE AND SPARE PARTS If you require an engineer or wish to purchase spare parts contact your local Service Force Centre by telephoning 0990 929929 Your telephone call will be routed to your local Service Force Centre For fu
5. ese hours in which case a premium will be charged EXCLUSIONS This Guarantee does not cover Damage or calls resulting from transportation improper use or neglect the replacement of any lilght bulbs or removable parts of glass or plastic Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United Kingdom e Appliances found to be in use within a commercial environment plus those which are the subject of rental agreements e Products of Zanussi manufacture which are not marked by Zanussi Ltd This guarantee is in addition to your statutory and legal rights ZANUSSI EUROPEAN GUARANTEE If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased your product The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e This guarantee relates to you and cannot be transferred to another user e Your new home is within the European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically i e a normal household Before you move please contact your nearest Customer Care Centre listed below to give them details of your new home They will then ensure that the
6. local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 29 99 Germany Nurnberg 49 0 911 323 2600 Italy Pordenone 39 0 1678 47053 Sweden Stockholm 46 0 8 738 79 50 UK Newbury 44 0 1635 521 313 INSTALLATION INSTRUCTIONS A It is dangerous to alter the specifications or attempt to modify this product in any way Technical Information DIMENSIONS HEIGHT 15 cm WIDTH 60 cm DEPTH 48 cm WEIGHT GROSS 8 5 kg NET 7 4 kg ELECTRICAL SUPPLY Voltage 50Hz 220 240 V POWER CONSUMPTION 190 W FAN MOTOR 110 W LAMP 2 x 40 80 W SUITABLE FOR INSTALLATION ABOVE OVER ELECTRIC HOB 7KW max OVER GAS HOB 10KW max SLOT IN GAS COOKER 13 5KW max SLOT IN ELECTRIC COOKER 12 4KW max Note CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89 336 Electromagnetic compatibility and subsequent modifications and Low Voltage directive 72 23 E ELECTRICAL CONNECTIONS This appliance must be earthed Electrical Requirements This appliance is fitted with a 3 core mains Any permanent electrical installation must cable and must be permanently connected to comply with the latest I E E Regulations and the electricity supply via a double pole switch local Electricity Board regulations For your own having 3mm minimum contact gap on each safety this should be undertaken by a qualified pole A Switched Fuse Connec
7. nt 100mm 4ins in diameter and the length should be nomore than 3 metres with one 900 bend 2 metres with two 900 bends Bends of more than 900 will reduce the efficiency of the hood and reduce the airflow Clearance Height The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications If the output of the appliance below the cooker hood exceeds the maximum outputs quoted please refer to the cooker manufacturer s installation instructions 11 Clearance Height A minimum clearance height of 650mm 25 is required when installed above a built in electric hob or 700mm 27 when installed above a built in gas hob A minimum clearance height of 685mm 27 is required when installed above a slot in electric oven or 787mm 30 when installed above a slot in gas oven When installed between adjoining wall cabinets the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm If the height of the wall cabinet is less than 450mm a gap of 50mm must be maintained either side of the hob This cooker hood must not be installed above a cooking appliance with a high level grill Unpacking The fittings supplied to install this cooker hood can be found with the instruction bo
8. ok inside the packaging and consists of the following Ducting spigot Blanking plate Wall fitting template Fitting Kit 2 Wall fixing brackets 4 Plastic rawl plugs 4 Wall bracket fixing screws 2 Security washers 2 Security nuts peng the Wall Brackets Using the paper template provided mark the hole positions on the wall for the bracket fixing screws Check that the hole differences are correct with a tape measure as stated on the template At this stage it is important to allow 15mm clear space above the cooker hood to enable it to be hooked onto the brackets and for subsequent removal for decorating or servicing Fit the brackets with the round ends facing downwards using the plastic rawl plugs and screws provided A Built in Electric Hob B Built in Gas hob C Slot in Electric Cooker 685mm minimum clearance 650mm minimum clearance 700mm minimum clearance D Slot in Gas Cooker 787mm minimum clearance 12 Venting The hood is more effective when used in the extraction setting ducted to the outside Venting kits maybe purchased through your retailer or DIY store and must be ducted to an outside vent of 100mm 4 minimum A The ducting used must be manufactured from fire retardant material which should conform to the relevant British Standard or DIN4102 B1 When the hood is ducted externally the charcoal filter must be removed and the slider control must be in the ducting positi
9. oker hood locates onto the two brackets Ensure that the cooker hood is correctly located before letting go LS To Level the Cooker Hood Remove the lower grille by pressing inwardly on the two slide catches located towards either side of the grille towards the front The grille will open from the front Slide the right edge of the grille forward until it clears the guide and then unhook the left hinge pin Support the grille when removing it from the guides carefully The two levelling screws will be visible towards either end of the back panel 14 Turn the screws clockwise to lift the front edge of the hood and use a spirit level to check the hood is positioned at right angles to the wall before fitting the security system The wall brackets have two studs and when the cooker hood is hung onto the brackets the studs project trought the holes above the levelling screws When the hood is level fit the two shake proof washers and nuts supplied to fully secure the cooker hood 15 Dir 89 336 CEE 73 23 CEE Electrolux Household Appliances Limited 2000 4324165 02 230300
10. ommended Under no circumstances should you attempt to repair the appliance yourself Repairs carried out by inexperienced persons may cause injury or more serious malfunction Refer to your local Zanussi Service Force Centre Always insist on genuine spare parts YOUR APPLIANCE OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen it will not extract steam To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing The cooker hood controls are located on the right hand side in the front fascia panel above the glass visor The Controls Fan ON OFF Speed Control Position 0 Off Position 1 Low Position 2 Normal Position 3 Boost Light ON OFF control 0 Off 1 On To Operate Select the required fan speed and light if required The appliance can be installed to recirculate or extract contaminated air The cooker hood is more effective when used in the extraction mode Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted In the recirculation mode contaminated air is passed through the charcoal filter to be purified and recirculated into the kitchen through a recirculation grille Extraction In the extraction mode the contaminated air enters the cooker hood passes through
11. on ES To Fit the Ducting 1 Fit the ducting spigot and blanking plate by aligning the interlocking lugs on the fittings with the recesses in the aperture 2 Insert and turn anti clockwise to lock spigot and blanking plate into position 3 Remove the charcoal filter and ensure the slider control is in the ducting position LS To Remove the Charcoal Filter il Open the visor and remove the metal inlet grille 2 Carefully remove the screw from the centre of the charcoal filter while holding the filter securely 3 The charcoal filter can now be removed Recirculation The charcoal filter must be fitted for recirculation and the slider control must be in the recirculation position 13 ES Wall Cabinet Fitting Before fitting the cooker hood beneath any type of wall cabinet ensure it is firmly fixed to the wall in accordance with the manufacturers instructions i Use the paper template provided to mark the hole positions on the underside of the cabinet Ensure the front edges of the template are aligned with the front edge of the cabinet carcase Check the distances are correct with a tape measure as stated on the template The four holes are 5mm 1 4 diameter If the ducting spigot is being used cut a circular hole using a pad saw or similar cutter ES Fitting the Cooker Hood to the Wall 1 Lift the hood squarely to the wall slightly higher than the brackets Lower the cooker hood until the co
12. ow the minimum height recommended under section Clearance Height or if the motor becomes overheated If the cut out device is activated switch off the fan motor and allow the cooker hood to cool The cut out device will reset itself when the fan motor has cooled significantly It is dangerous to alter the specifications or modify this product in any way When installed between adjoining wall cabinets the wall cabinets must not overhang the hob If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose Do not install above a cooker with a high level grill Child Safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the appliance During Use This product is for domestic use only Never leave frying pans unattended during use as over heated fats and oils might catch fire Never do flamb cooking under this cooker hood Do not leave naked flames under the hood Maintenance and Service This appliance can be a hazard if the synthetic paper and charcoal filters are not replaced as rec
13. rther details please see the accompanying customer care book For general assistance with your appliance or for information on Zanussi products please contact our Customer Care Department Customer Care Department Zanussi Zanussi House Hambridge Road Newbury Berkshire RG14 5EP Tel 01635 521 313 calls to this number may be recorded for training purposes PEACE OF MIND FOR TWENTY FOUR MONTHS STANDARD GUARANTEE CONDITIONS We Zanussi Ltd undertake that if within twenty four months of the date of the purchase this Zanussi built in appliance or any part there of is proved to be defective by reason only of faulty workmanship or materials the company will at our option repair or replace the same FREE OF ANY CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the electrical supply stated on the rating plate The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s operating and maintenance instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us All service work under this guarantee must be undertaken by Zanussi Service Force Centre Any appliance or defective part replaced shall become the property of this company Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside th
14. the grease filter and out through the ducting to the atmosphere A When the ducting position is selected the charcoal filter is not required Never do flamb cooking under this cooker hood Take extra care when frying and never leave frying pans unattended during use as over heated fats and oils might catch fire Do not leave naked flames under the cooker hood Ensure the visor is open when using the hob even if the fan on the hood is not switched on Ensure heating areas on your hob are covered with pots and pans when using the hob and cooker hood simultaneously DUCTING EVACUATION ABLUFT ASPIRANTE RECYCLAGE UMLUFT N FILTRANTE MAINTENANCE AND CLEANING A Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply The cooker hood must be kept clean a build up of grease or fat can be a fire hazard External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent Always wear protective gloves when cleaning the hood Never use scouring pads or abrasive cleaners Never use excessive amounts of water when cleaning particularly around the control panel Charcoal Filter The charcoal filters cannot be cleaned The filter should be replaced at least every three months or more frequently if the hood is used more than three hours per day ES To Remove Replace the Charcoal Filter 1 Open the visor and remove the metal inlet grille
15. tion Unit to electrician e g your local Electricity Board or a BS1363 Part 4 fitted with a 3 Amp fuse is a contractor who is on the roll of the National recommended mains supply connection Inspection Council for Electrical Installation accessory to ensure compliance with the Safety Contracting NICEIC Requirements applicable to fixed wiring instructions Electrical Connection Before connecting to the mains supply ensure This appliance conforms to BS 800 1988 and that the mains voltage corresponds to the EEC Directive No 78 308 regarding voltage on the rating plate inside the cooker suppression of radio and television hood interference 10 INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown A All installations must comply with the local authorities requirements for the discharge of exhaust air Incorrect installation may affect the safety of this cooker hood Installation Requirements A Before installation check the wall to which the cooker hood is to be fitted for electric cables water pipes or gas If it is necessary to fix the hood to a hollow construction plaster or partition board structure then it should be sufficiently reinforced to be quite rigid in the area of the cooker hood mounting brackets and the appropriate rawl plugs used for this type of fixing not supplied Ducting The ducting must be fire retarda
Download Pdf Manuals
Related Search