Yamaha PSR1000/2000 User's Manual
Contents
1. 4 Play the keys to hear the Voice s 5 When finished turn OFF LAYER button VIRTUAL ORGAN DRAWBARS PSR2000 1 Press ORGAN FLUTES in the VOICE section 2 Press SOUND CREATOR 3 Use BACK and NEXT to select FOOTAGE page 4 Use buttons 1 8 under display to adjust drawbars PLAYING THE STYLES 1 Press a button in STYLE section Ex POP amp ROCK 2 Use A J to select a Style Ex 60 sRock 1 3 Turn on the ACMP button red LED illuminates 4 Press INTRO then SYNC START 5 Play a chord in the left section of the keyboard 6 Press ENDING to finish hearing the Style 1 4 lt a TEE USING ONE TOUCH SETTINGS 1 Select a Style see above 2 The 4 ONE TOUCH SETTING buttons will now call up 4 appropriate Voices for the selected Style MUSIC FINDER 1 Press MUSIC FINDER 2 Use 2 4 and v to select a Song 3 A Style and Voice is automatically set up for the Song NOTE Custom song titles amp setups can also be stored VOCAL HARMONY PSR2000 1 Plug a 250 ohm dynamic mic into MIC LINE IN jack 2 Adjust INPUT VOLUME knob on back of unit while singing into mic 3 In MIC section of front panel make sure VOCAL HARMONY is ON and TALK is OFF 4 Press VH TYPE SELECT to select Vocal Harmony types 5 Start a Style playing with a chord see above 6 While holding the chord sing into the mic2. Manual p 84 Data List p 25 30 XV Storing Intro and Ending Settings Each Preset Style on the PSR1000 2000 has a specific Intro and Ending length and type The choices available for the Intro are Countin 4bar1 or 4bar2 The choices available for the Ending are Fill amp Hit 2bar or 4bar These variations of Intro and Ending may be changed temporarily from the front panel or stored permanently to User memory or Floppy Disk as a User Style NOTE The Intro and Ending settings are not stored as a Registration parameter and therefore cannot be stored to the REGISTRATION MEMORY buttons they must be stored with a Style Changing Intro and Ending Settings Temporarily 1 Select a desired Style 2 From the MAIN screen press the E INTRO ENDING button 3 Use the D button to select the Intro setting 4 Use the E button to select the Ending setting 5 Press the EXIT button to return to the MAIN screen Changing Intro and Ending Settings Permanently 1 Make the desired Intro and Ending settings see steps above 2 Press the DIGITAL RECORDING button 3 Press the B STYLE CREATOR button 4 Use the BACK and NEXT buttons to display the ASSEMBLY page 5 Press the J SAVE button 6 Use the BACK and NEXT buttons to select the USER memory page or the FLOPPY DISK page 7 Press the 7 v SAVE button 8 Use the 1 8 and v toggle buttons to name
3. 7 Adjust Style Volume by first pressing BALANCE then using 2 4 and v to control the Volume PLAYING SONGS WITH LYRICS FROM DISK 1 Insert a Standard MIDI File SMF disk with Lyric data 2 Press A SONG button in MAIN screen 3 Use A J to select a Song 4 Press B Lyrics button 5 In SONG section of front panel press START STOP to start the Song the Lyrics will appear in the display in time with the music 6 Press START STOP to stop the Song PART MUTING amp VOLUME CONTROL 1 Play a Style or Song see above 2 To mute un mute Parts with buttons 1 8 press CHANNEL ON OFF to display STYLE or SONG 3 To adjust Part volumes with buttons 1 8 press MIXING CONSOLE to display STYLE or SONG for VOL VOICE page SONG RECORDING Quick Method In the SONG section of the front panel 1 Press and hold REC then press TOP 2 Release the buttons then select a Style and Voice 3 Press and hold REC then press the Track buttons above it for the Tracks that are to be recorded EXAMPLE STYLE L or R 4 Release the buttons then play the keyboard to start recording 5 Press REC to stop recording 6 To play the Song press TOP then START STOP 7 To stop the Song press START STOP again PSR1000 2000 STEP BY STEP PROCEDURES I Copying Files from one Floppy Disk to Another Floppy Disk ll Crea
4. N MAIN A and PATTERN LENGTH 1 Copying Parts If desired copy Parts from any existing Styles into the 8 different Channels Tracks of the new Style If all Parts are to be recorded from scratch this step may be skipped 1 Press the NEXT button to display the ASSEMBLY page in the screen 2 The A D and F I buttons correspond to the 8 Parts that make up the Style RHYTHM1 RHYTHM2 BASS CHORD1 CHORD2 PAD PHRASE 1 and PHRASE2 To select a Part in an existing Style press one of the A D or F I buttons twice the chosen Part may then be selected from any of the existing Styles using the A J buttons EXAMPLE The RHYTHM2 Part from the Style 60 sGtrPop may be used for the RHYTHM2 Part in the New Style 3 Press the EXIT button to return to the ASSEMBLY page 4 Repeat steps 2 3 for the remaining 7 Parts of the Style if desired 5 Press the BACK button to return to the BASIC page Recording an original Part onto a Channel from scratch 1 Press the F REC CH button to display the 8 Record Channels in the screen 2 Select a Channel for recording by simultaneously holding the F REC CH button while pressing one of the 8 v toggle buttons below the screen EXAMPLE The RHY2 Channel will display REC in the screen when selected 3 Select a Voice or Drum Kit for the Channel by first pressing the toggle button below it and then using the A J and toggle bu
5. PSR1000 2000 noganannnnan TOP FEATURES saannnnnnnnn e Microphone input with Vocal Harmony PSR2000 e Lyric display for song disks with lyrics e Custom lyric input for User Songs New e Notation display PSR2000 New e Large Full Dot backlit LCD screen New e Music Finder with 500 song selections New e Organ Flutes with 8 virtual drawbars PSR2000 e High quality Voices including stereo samples New e 3 Intros Endings 4 Variations Fills per style e To Host port for direct hookup to computer e Pitch Bend and Modulation Wheels e Groove Dynamics function for Auto Accompaniment e Interactive Help in 5 languages New SYSTEM DATA RESET This will erase any custom settings 1 Power on while holding down key furthest to right C PLAYING THE DEMOS 1 Press DEMO to play songs randomly 2 Use BACK and NEXT to select a Demo category 3 Use 1 and 2 to select different pages 4 Use A J to select an item on a page to demo 5 Press START STOP in SONG section to stop Demo 6 From the FUNCTION page press 8 v AUTO to play all Demo items automatically 7 Press EXIT to exit Demo Mode PLAYING THE VOICES 1 Press a category button in the VOICE section Ex PIANO amp HARPSI 2 Use A J to select a Voice Ex GrandPiano 3 To layer two Voices press EXIT turn ON LAYER button press G LAYER and repeat steps 1 2
6. SET page 5 Press the I MUSIC FINDER button 6 Select the new MUSIC FINDER file 7 Press the G Replace button to replace the original MUSIC FINDER records 8 Press the MUSIC FINDER button to display the new selections Owner s Manual p 69 72 VIII Making Global Settings for Voices If Voice settings such as Effects EQ and Harmony are changed for a Voice these settings normally will reset to something else when a different Voice is chosen However settings can be made to affect all Voices globally by editing the VOICE SET page For this example all Effects will be turned OFF globally for all Voices 1 Press the FUNCTION button 2 Press the E REGIST SEQUENCE FREEZE VOICE SET button 3 Use the BACK and NEXT buttons to display the VOICE SET page in the screen 4 Use the A and B v buttons to select a Voice section MAIN LAYER or LEFT 5 Use the 5 and v toggle buttons to delete the checkmark from the box under the word EFFECT 6 Press the EXIT button twice to return to the MAIN screen 7 If the DSP button on the right side of the front panel is ON red LED illuminated press it once to turn it OFF All Voices in the selected Voice section will no longer have Effects applied to them Owner s Manual p 143 IX Making Songs Play Continuously In the SONG SETTING screen the Song Chain Play function can be turned ON to automatically pla
7. Voice to the original Preset Voice the screen will actually display the original Preset Voice name when a REGISTRATION MEMORY button using a User Voice is selected even if the name was edited for the User Voice However when the User Voice is selected directly from the USER VOICE button the screen will display the actual edited name of the User Voice XIV Some Settings are not Storing with the Registrations Settings that are saved with a Registration can be filtered by the user via the REGISTRATION MEMORY CONTENTS screen If something is not saving with a Registration it is possible that that type of setting has not been selected to be saved with the Registration Memory The user should also check the Parameter Chart on p 25 30 in the PSR1000 2000 Data List booklet to verify that the desired settings can be saved with a Registration Selecting Settings to be Saved with a Registration 1 Press the MEMORY button to display the REGISTRATION MEMORY CONTENTS screen 2 Using the 5 and v toggle buttons select a desired Group of settings 3 Using the 8 and v toggle buttons put a check mark next to the selected Group to be saved 4 Repeat steps 2 3 for other desired setting Groups 5 If something is still not storing with a Registration check the Parameter Chart on p 25 30 in the PSR1000 2000 Data List booklet to make sure that it is a setting which can be saved with a Registration Owner s
8. Y DISK page 4 Press the 3 F LCD button to select COPY The COPY display will appear 5 Select the desired Song file s using the appropriate LCD button s 6 Press the 7 F LCD button to select OK 7 Press the BACK button to select the USER page 8 Press the 4 F LCD button to execute the PASTE command and paste the selected Song file s to the USER page 9 Eject the source floppy disk 10 Insert the destination floppy disk to which the Song file s will be copied 11 Press the 3 F LCD button to select COPY The COPY display will appear 12 Select the desired Song file s using the appropriate LCD button s 13 Press the 7 F LCD button to select OK 14 Press the NEXT button to display the FLOPPY DISK page 15 Press the 4 F LCD button to execute the PASTE command and copy the song file s to the destination floppy disk To duplicate entire disks the DISK TO DISK COPY feature may be used 1 Insert the source floppy disk containing the files to be copied 2 Press the FUNCTION button 3 Press the I UTILITY button 4 Use the BACK and NEXT buttons to select the DISK page in the screen 5 Press the F DISK TO DISK COPY button 6 Press the G OK button 7 When prompted on the screen insert the destination disk 8 Press the G OK button When the screen displays Completed the pr
9. ation Bank File 3 Select the desired Registration Bank File a If Folders were first created use the A J buttons to select the desired Folder then the desired Registration Bank File b If Folders were not created use the A J buttons to directly select the desired Registration Bank File 4 Press the G YES button to confirm the choice 5 The 8 REGISTRATION MEMORY buttons will now call up the Registrations in the selected Bank Owner s Manual p 84 86 XIII Saving User Voice Edits to Registration Memory Unlike previous PSR models the PSR1000 2000 actually stores the edited parameter data used to create a User Voice if that User Voice is stored to one of the REGISTRATION MEMORY buttons This is a very useful feature because if the user deletes or overwrites the User Voice later on the REGISTRATION MEMORY button that it was originally stored to will still call up the sound of the User Voice it accomplishes this by applying the edited Voice parameters to the original Preset Voice that was edited On previous models if a User Voice was deleted that was originally stored to a Registration it would be gone when the Registration tried to call it up This feature also allows the user to delete User Voices in order to free up more memory without losing them in the Registration settings NOTE Because the REGISTRATION MEMORY buttons apply the edited parameters of the User
10. cked up to floppy disk if the unit will be unplugged from an AC outlet for more than a week If the unit is left unplugged for over a week the data may be lost Another way that data may be lost is if the storing procedure for System Setup data is performed incorrectly on the PSR1000 2000 if a user changes the settings in a screen they must remember to press the EXIT button afterward before turning OFF the power or the data Is lost Owner s Manual p 4 39 IV Editing Song Track Parameters such as Voice and Volume Individual Song Track Parameters such as Voice Volume Pan Tempo etc can be changed by selecting the MIXING CONSOLE function from the SET UP view in SONG CREATOR Changing the Voice for Example on a Track 1 Load the Song into the PSR1000 2000 2 Press the DIGITAL RECORDING button 3 Press the A SONG CREATOR button 4 Use the BACK and NEXT buttons to display the CHANNEL page 5 Use the A and B buttons to display the SET UP view in the screen 6 Press the MIXING CONSOLE button repeatedly to select Channels 1 8 or Channels 9 16 at the bottom of the screen CH1 8 or CH9 16 will display at the top of the screen 7 Use the BACK and NEXT buttons to display the VOL VOICE page 8 Press the H button to select the VOICE section in the screen 9 Use the 1 8 toggle buttons under the screen to select a Track 10 Select a new Voice for the Track using the b
11. drive For further organization Folders can be created and named then multiple Registration Bank Files can be organized within each Folder This hierarchical method is similar to that used in Microsoft Windows Folders and Files may be moved around using the familiar CUT COPY PASTE DELETE functions Saving Registrations 1 To save a single front panel setting Registration to one of the 8 REGISTRATION MEMORY buttons press and hold the MEMORY button then press the desired REGISTRATION MEMORY button 1 8 WARNING These settings are saved into a temporary memory buffer and will be lost when the unit is turned OFF unless the following steps are performed 2 Release the buttons 3 Repeat steps 1 2 for subsequent Registrations up to 8 total 4 Press the EXIT button twice to return to the Main screen 5 Press the J REGISTRATION BANK button 6 Use the BACK and NEXT buttons to select a permanent memory location USER memory or FLOPPY DISK drive to store the Registrations into 7 Registration Banks can be grouped into Folders a If it is desired to organize Registration Banks by first grouping them into Folders press the 7 v NEW button under the Folder icon in the screen 1 Use the 1 8 toggle buttons under the screen to name the Folder 2 Press the 8 OK button to store the Folder into the chosen memory location b If grouping Registration Banks
12. e screen The selected Channel will display REC in the screen 4 Select a Part that the Channel will be recording from EXAMPLE The MAIN Voice section of the keyboard for Channel 1 a Press and hold REC then press one of the 1 8 or v toggle buttons for the desired Channel b Use the C and D v buttons to select a Part 5 To record multiple Channels Parts simultaneously repeat steps 2 4 6 To start recording begin playing the keyboard or press the silver START STOP button in the SONG section of the front panel NOTE When recording Auto Accompaniment Parts from a Style it is a good idea to turn ON the INTRO button and SYNC START button first red LED illuminates on both and then play the chords for the Style to trigger the recording This way the Song will have a more professional sounding introduction 7 To stop recording press the REC button If recording a Style the ENDING rit button can also be used for a professional sounding ending 8 Play back the recording a Press the TOP button b Press the silver START STOP button to start the Song c Press the silver START STOP button again to stop the Song 9 To record additional Parts repeat steps 2 8 Saving the Song Once a Song has been recorded it can be saved to the USER memory or to the FLOPPY DISK memory 1 Press the A SONG button 2 Use the BACK and NEXT but
13. essor They will both be heard therefore when the Balance is panned all the way over to the Lead L sound not just the Lead sound For example the effect Speedy Mouse creates a high pitched cartoon like voice along with the user s original voice Speedy Mouse uses Gender change to accomplish this so panning the Balance control fully to L on the left does not give the user the Lead sound only it simply gets rid of the Harmony 1 and Harmony 2 sounds To eliminate the Lead sound and get the cartoon like voice only the effect must be edited To Hear Effect Only no Lead in Speedy Mouse Example 1 Press the VH TYPE SELECT button 2 Select the Vocal Harmony Type SpdyMouse 3 Press the 3 EDIT toggle button to display the VOCAL HARMONY EDIT page in the screen 4 Make the following changes HARM GENDER TYPE AUTO LEAD GENDER TYPE OFF LEAD GENDER DEPTH 64 UPPER GNDR DEPTH 63 LOWER GNDR DEPTH 63 Saving the Edited Effect 1 Press the I SAVE button 2 Rename the effect if desired 3 Press the 8 OK button Balance Setting 1 Press the MIC SETTING button 2 Press the J button to select VOCAL HARMONY CONTROL 3 Use the 4 v toggle button to select L lt H63 for the Balance Bal section Owner s Manual p 130 132
14. into Folders is not desired proceed to Step 8 8 Press the 6 v SAVE button under the screen This creates a Registration Bank File containing the current 8 Registrations that are stored to the 8 REGISTRATION MEMORY buttons 9 Use the 1 8 toggle buttons under the screen to name the Registration Bank File 10 Press the 8 OK button to save the Registration Bank File into the chosen memory location 11 To name the 8 individual Registrations contained in the Registration Bank File do the following a Press the 8 EDIT button b Press the 1 v NAME button c Use the A D and F I buttons to select the desired Registration d Press the 7 v OK button e Use the 1 8 toggle buttons under the screen to name the Registration f Press the 8 OK button to store the name g Press the 8 v button to return to the REGISTRATION BANK screen h Press the EXIT button repeatedly to return to the MAIN screen Loading Registrations NOTE The REGISTRATION MEMORY button settings are cleared whenever the unit is turned OFF To load Registrations back in after the unit has been turned ON or to select a different Registration Bank the following procedure must be performed 1 Press the J REGISTRATION BANK button 2 Use the BACK and NEXT buttons to select a memory location USER or FLOPPY DISK containing the desired Registr
15. nd hold down the rightmost white key C while turning ON the keyboard 3 Once the power is ON release the key The keyboard will reinitialize the system Setup to the original factory settings To Reset All or Selected Settings to Original Factory Settings WARNING All user stored data Registrations User Styles Multipads User Voices User Songs MIDI settings will be deleted If the current settings and data are not expendable create a backup before executing the Factory Reset This can be done by performing a Bulk Dump to an external MIDI storage device or by saving the user stored data to a floppy disk via the internal disk drive of the keyboard 1 Press the FUNCTION button 2 Press the I UTILITY button 3 Use the BACK and NEXT buttons to display the SYSTEM RESET page in the screen 4 Use the A E buttons to select the desired data to be reset 5 Press the 1 FACTORY RESET EXECUTE button 6 Press the G YES button to confirm 7 Press the G YES button again to execute the reset Owner s Manual p 151 Vil Loading Music Finder Files into a PSR1000 2000 Custom MUSIC FINDER files can be loaded into a PSR1000 2000 to replace the file containing the original factory selections 1 If the file is on a floppy disk insert the floppy disk 2 Press the FUNCTION button 3 Press the I UTILITY button 4 Use the BACK and NEXT buttons to display the SYSTEM RE
16. ocess is finished NOTE If there is a large amount of data on the disk the screen may display a message asking for the source disk again followed by a repeat of the procedures in steps 5 7 Owner s Manual p 43 150 ll Creating a User Style The following procedure describes how to create a User Style from scratch This is useful when the PSR1000 2000 does not have a built in Style which fits the style of music that the user wants to play Creating a User Style from scratch is also useful to create custom drum accompaniments A Style can be created completely from scratch by first selecting NEW STYLE from the BASIC section of STYLE CREATOR then recording to the 8 Auto Accompaniment Channels Tracks for the Style NOTE Yamaha Style Disks Auto Accompaniments are available for purchase online at www yamahamusicsoft com To order by phone call Music Dispatch at 800 637 2852 Ask for the Hal Leonard Music Software Catalog Selecting a New Style 1 Press the DIGITAL RECORDING button 2 Press the B STYLE CREATOR button 3 Press the C NEW STYLE button 4 Press the B button and use the toggle buttons beneath the screen to select a TEMPO and a BEAT meter for the Style EXAMPLE TEMPO 120 and BEAT 4 4 5 Press the A button and use the toggle buttons beneath the screen to select an Auto Accompaniment SECTION and PATTERN LENGTH amount of measures for the Style EXAMPLE SECTIO
17. s for each Track of the Song 7 When finished press the D EXECUTE button 8 When finished press the I SAVE button 9 Use the BACK and NEXT buttons to select a permanent memory area USER memory or FLOPPY DISK to store the transposed Song into 10 Use the A J buttons to select a location in the chosen memory area 11 Press the 6 v SAVE button under the screen 12 Use the 1 8 toggle buttons under the screen to name the Song 13 Press the 8 OK button to save the Song into the chosen memory location Owner s Manual p 104 XVII Using Lead Harmony Balance in Vocal Harmony Control on a PSR2000 The Vocal Harmony processor uses two parts for Vocal Harmony effects on the PSR2000 One part is used to produce the Harmony 1 and Harmony 2 sounds the other part is used for the original Lead sound as well as the Gender change sound The VOCAL HARMONY CONTROL section of the MICROPHONE SETTING screen displays a control for balancing between the Lead L and Harmony H sounds For effects using harmonization and no Gender change this control provides an easy way to mix the Lead level with the Harmony level including the ability to hear only the Lead sound or only the Harmony sound However this control is not as useful on effects which use the Gender change effect This is because the Lead sound and Gender change sound are both coming from the same part of the proc
18. the Data Dial to select a section to be triggered EXAMPLE MAIN LAYER or LEFT NOTE To control the PSR1000 2000 the same way it s own keyboard does controlling whatever sections are active on the front panel select KEYBOARD 10 To control ONLY the Auto Accompaniment section independent of the keyboard do the following a Use the BACK and NEXT buttons to select the CHORD DETECT page in the MIDI screen b Use the A B v and 1 8 toggle buttons to select ON for the desired MIDI Channel the Channel being transmitted by the external MIDI device in the screen 11 Press the EXIT button once 12 Press the NEXT button to select the USER page in the MIDI screen 13 Use the A J buttons to select a destination to save the edited MIDI Setup to 14 Press the 6 v SAVE button 15 Use the 1 8 toggle buttons to name the edited MIDI Setup 16 Press the 8 OK button to store it 17 Press the EXIT button twice to return to the MAIN screen Owner s Manual p 147 VI Factory Reset Procedure The standard Yamaha factory reset procedure for many PSR Series keyboards will initialize the PSR1000 2000 System Setup Data but not other data such as the MIDI Setup Music Finder and User Files Folders to do this further steps are required see below To Reset System Setup Only to Original Factory Settings 1 Turn OFF the keyboard 2 Press a
19. the edited Style 9 Press the 3 OK button to save the Style to the memory location chosen in step 6 Owner s Manual p 66 112 113 XVI Transposing a Song The TRANSPOSE and buttons on the front panel of the PSR1000 2000 are for transposing the pitch that the keyboard plays To temporarily transpose the key of a Song use the TUNE section of the MIXING CONSOLE screen To permanently transpose the key of a Song and re save it use the CHANNEL TRANSPOSE feature on the CHANNEL page of the SONG CREATOR Transposing the Pitch of the Keyboard 1 Use the TRANSPOSE and buttons on the front panel to transpose the pitch of the keyboard up or down in half step increments Transposing a Song Temporarily 1 Select a Song 2 Press the MIXING CONSOLE button to the left of the screen 3 Use the BACK and NEXT buttons to select TUNE at the top of the screen 4 Use the 2 or v toggle buttons under SONG in the screen to transpose the Song up or down in half step increments Transposing a Song Permanently 1 Select a Song 2 Press the DIGITAL RECORDING button to the left of the screen 3 Press the A SONG CREATOR button 4 Use the BACK and NEXT buttons to select the CHANNEL page in the screen 5 Use the A and B buttons to select CHANNEL TRANSPOSE 6 Use the toggle buttons below the screen to select the desired transposition amount
20. ting a User Style lll Data will not Save Properly IV Editing Song Track Parameters such as Voice and Volume V Enabling an External MIDI Device to Control Keyboard Sections VI Factory Reset Procedure Vil Loading Music Finder Files VIII Making Global Settings for Voices IX Making Songs Play Continuously X Recording and Saving a Song XI Recording to PSR1000 2000 Sequencer from External MIDI Source XII Saving and Loading Registrations XIII Saving User Voice Edits to Registration Memory XIV Some Settings are not Storing with the Registrations XV Storing Intro and Ending Settings XVI Transposing a Song XVII Using Lead Harmony Balance in Vocal Harmony Control on a PSR2000 I Copying Files from one Floppy Disk to Another Floppy Disk IMPORTANT Commercially available music data is subject to protection by copyright laws Copying commercially available data is strictly prohibited except for personal use Some music software is purposely copy protected and cannot be copied To copy specific files from disk to disk the files must first be copied from the source floppy disk to the USER page before it is possible to paste them to the destination floppy disk 1 Insert the source floppy disk containing the file s to be copied For this example the steps for copying Song files will be shown 2 Press the A LCD button to select SONG 3 Press the NEXT button to select the FLOPP
21. tons to select the USER memory page or the FLOPPY DISK memory page 3 Press the 6 v SAVE button 4 Use the 1 8 and v toggle buttons to name the Song 5 Press the 8 OK button to save the Song to the memory location chosen in step 2 Owner s Manual p 92 95 XI Recording to PSR1000 2000 Sequencer from External MIDI Source The on board sequencer of the PSR1000 2000 can be used to record MIDI data from external sources such as MIDI bass pedals keyboards and hardware or computer based sequencers This is done by assigning the desired MIDI Receive Channels to Keyboard mode 1 Press the FUNCTION button 2 Press the H MIDI button 3 Use the BACK and NEXT buttons to display the PRESET page in the screen 4 Press the A All Parts button 5 Press the 84 EDIT button 6 Use the BACK and NEXT buttons to display the RECEIVE page in the screen 7 Use the A and B buttons to select a desired MIDI Channel 8 Use the 2 and 2 v buttons to select KEYBOARD for that Channel Any MIDI Channels with KEYBOARD selected will receive incoming MIDI data from an external source which can be recorded onto a corresponding Track in the PSR1000 2000 Song Creator Owner s Manual p 147 XII Saving and Loading Registrations Registration settings are saved in Banks of 8 to either the internal USER memory or the FLOPPY DISK
22. ttons to make a selection 4 Press the EXIT button to return to the BASIC screen 5 Press the black START STOP button in the STYLE section of the front panel Recording begins and the Metronome click is heard 6 Play the desired Part on the keyboard 7 If a mistake is made while recording a Rhythm Part hold the E RHY CLEAR button and touch the note corresponding to the Drum Voice which was played incorrectly the entire phrase recorded with that Drum Voice will be cleared 8 When finished press the black START STOP button again 9 Repeat steps 2 8 to record other Channels 10 When finished recording all Channels press the EXIT button once to return to the original BASIC screen view Saving the User Style 1 Press the I SAVE button to select a destination for storing the User Style 2 Use the BACK and NEXT buttons to display the USER or FLOPPY DISK page 3 Press the 6 v toggle button to name the User Style 4 Use the toggle buttons to select the characters for the User Style name 5 When finished press the 8 OK toggle button The User Style is now saved 6 Press the EXIT button twice to return to the MAIN screen Owner s Manual p 108 117 lll Data will not Save Properly The Internal RAM Memory in the PSR1000 2000 is volatile Any user stored data in this memory location such as Songs Styles System Setup data Music Database information etc must be ba
23. uttons in the VOICE section on the front panel 11 Press the EXIT button twice to return to the SET UP view 12 Press the D EXECUTE button to put the edited parameters into the Song Saving the Edited Song 1 Press the I SAVE button 2 Use the BACK and NEXT buttons to select the destination USER or FLOPPY DISK 3 Press the 6 v SAVE button 4 Press the 8 OK button 5 Press the F YES button to overwrite the old Song version with the new one Owner s Manual p 102 104 V Enabling an External MIDI Device to Control Keyboard Sections The PSR1000 2000 can be configured so that the MAIN LAYER and LEFT Voice sections can be individually controlled by an external MIDI device It can also be configured so that an external MIDI device can control it the same way i s own keyboard does controlling whatever sections are active on the front panel 1 Press the FUNCTION button 2 Press the H MIDI button 3 Use the BACK and NEXT buttons to select the PRESET page in the MIDI screen 4 Press the A All Parts button 5 Press the NEXT button 6 Press the 8 EDIT button 7 Use the BACK and NEXT buttons to select the RECEIVE page in the MIDI screen 8 Use the A or B v buttons to select the desired MIDI Channel the Channel being transmitted by the external MIDI device in the screen 9 Use
24. y Songs consecutively and continuously 1 Press and hold the DIRECT ACCESS button then press the REPEAT button 2 Press the I button to select SONG CHAIN PLAY ON in the screen Owner s Manual p 137 X Recording and Saving a Song The PSR1000 2000 can record Songs with up to 16 separate Channels tracks each Channel using a different Voice There are two different methods for recording Quick Recording for recording a Song in one or two takes and Multi Recording for recording multiple Channels by as little as one Channel at a time Quick Recording In the SONG section of the front panel 1 Press and hold REC then press TOP to create a new Song 2 Release the buttons then select a Style and Voice 3 Press and hold REC then press the Track buttons above it for the Tracks Channels which are to be recorded EXAMPLE STYLE L or R 4 Release the buttons then play the keyboard to start recording 5 Press REC to stop recording 6 To play the Song press TOP then START STOP 7 To stop the Song press START STOP again Multi Recording In the SONG section of the front panel 1 Press and hold REC then press TOP to create a new Song 2 Select a desired Voice or Style to be recorded 3 To select a Channel for recording simultaneously hold the REC button while pressing the 1 8 or v toggle button which corresponds to the desired Channel in th
Download Pdf Manuals
Related Search