Yamaha DSP1D-EX User's Manual
Contents
1. If Indicator B is flashing unit B is in standby mode CONTROL I O 1 2 indicators These indicators indicate which one of two CON SOLE 1 2 IN OUT jacks 8 on the rear panel is cur rently effective Note When you turn on the power to the DSP1D DSP1D EX and the CS1D and communication between the DSP1D DSP1D EX and the CS1D is established one of these two indicators lights up If neither one lights up check the connection of the CONSOLE 1 2 IN OUT jacks on the rear panel Error indication e If the CONTROL I O 1 indicator is flashing Communication between the CS1D control surface and the DSP1D is not established The CONSOLE 1 2 IN OUT jacks or the PC CON TROL port is not connected correctly 3 INPUT CONFIGURATION 48CH 96CH indicators These indicators indicate how many input channels are currently available On the DSP1D the 48CH indicator lights up On the DSP1D EX the 96CH indicator lights up Error indication e If the INPUT CONFIGURATION 48CH is flashing The signal is not locking to the word clock POWER ON OFF switch Use this switch to turn the power to the DSP1D DSP1D EX on or off When the power is turned on the indicators 1 light up MIDI IN OUT THRU connectors These connectors are used to transmit and receive Program change messages MMC and other MIDI messages among external MIDI devices PC CONTROL RS 232 C USB ports Connect these ports to a PC that ru2. of the battery at the moment of the disposal at the end of the service life please consult your retailer or Yamaha Service Center as follows Yamaha Music Nederland Service Center Address Kanaalweg 18 G 3526 KL UTRECHT Tel 030 2828425 O Do not throw away the battery Instead hand it in as small chemical waste Windows 95 9809 is a registered trademark of Microsoft in the U S A and other countries E Precautions Do not allow water to enter this unit or allow the unit to become wet Fire or electrical shock may result Connect this unit s power cord only to an AC outlet of the type stated in this Owner s Manual or as marked on the unit Failure to do so is a fire and electrical shock hazard Do not scratch bend twist pull or heat the power cord A damaged power cord is a fire and electrical shock hazard Do not place heavy objects including this unit on top of the power cord A damaged power cord is a fire and electrical shock hazard In particular be careful not to place heavy objects on a power cord covered by a car pet Be sure to ground the unit to avoid the risk of electri cal shock If you notice any abnormality such as smoke odor or noise or if a foreign object or liquid gets inside the unit turn it off immediately Remove the power cord from the AC outlet Consult your dealer for repair Using the unit in this condition is a fire and electrical shock hazard Should this unit AC adapter power supp
3. to be the source of interference which can be determined by turning the unit OFF and ON please try to eliminate the problem by using one of the following measures Relocate either this product or the device that is being affected by the interference Utilize power outlets that are on different branch circuit breaker or fuse circuits or install AC line filter s In the case of radio or TV interference relocate reorient the antenna If the antenna lead in is 300 ohm ribbon lead change the lead in to coaxial type cable If these corrective measures do not produce satisfactory results please contact the local retailer authorized to distribute this type of product If you can not locate the appropriate retailer please contact Yamaha Corporation of America Electronic Service Division 6600 Orangethorpe Ave Buena Park CA 90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries WARNING THIS APPARATUS MUST BE EARTHED IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety eart
4. V480360 RO 1 IP 16 200 AP Printed in Japan YAMAHA DSP UNIT DSP ID DSP UNIT DSP ID EX Owner s Manual Y o E Led gt Y e E ES dd D GO lt GO H m FCC INFORMATION U S A 1 IMPORTANT NOTICE DO NOT MODIFY THIS UNIT This product when installed as indicated in the instructions contained in this manual meets FCC requirements Modifications not expressly approved by Yamaha may void your authority granted by the FCC to use the product IMPORTANT When connecting this product to accessories and or another product use only high quality shielded cables Cable s supplied with this product MUST be used Follow all installation instructions Failure to follow instructions could void your FCC authorization to use this product in the USA NOTE This product has been tested and found to comply with the requirements listed in FCC Regulations Part 15 for Class B digital devices Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices This equipment generates uses radio frequencies and if not installed and used according to the instructions found in the users manual may cause interference harmful to the operation of other electronic devices Compliance with FCC regulations does not guarantee that interference will not occur in all installations If this product is found
5. ard ENGINE ID E Front panel A B CONTROL 1 0 1 2 2 INPUT r CONFIGURATION gt dt rr 48CH 96CH YAMAHA DSP UNIT Rear panel m CONTROL I O CONSOLE DIGITAL O OUTPUT USB WORD CLOCK e HO CS ENGINE ID A B indicators These indicators indicate whether the DSP1D DSP1D EX is connected to the engine A or engine B channel Indicator A lights up if the DSP1D DSP1D EX is con nected to the engine A channel jacks of the CS1D con trol surface DIGITAL I O jack A and CONTROL I O jack A Indicator B lights up if the DSP1D DSP1D EX is connected to the engine B channel jacks of the CS1D control surface DIGITAL I O jack B and CON TROL I O jack B Error indication e If both ENGINE ID A and B indicators are flash ing There is a malfunction in the internal board PDB GDB IDB1 2 EDB EMB or CIB Or the necessary board does not exist e If either ENGINE ID A or B indicator is flashing During the Mirror mode operation the ENGINE ID indicator for the unused DSP1D DSP1D EX flashes indicating that the unit is in standby mode If Indicator A is flashing unit A is in standby mode
6. h symbol or coloured GREEN and YELLOW The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED This applies only to products distributed by YAMAHA KEMBLE MUSIC U K LTD ADVARSEL Lithiumbatteri Eksplosionsfare ved fejlagtig handtering Udskiftning ma kun ske med batteri af samme fabrikat og type Lev r det brugte batteri tilbage til leverandoren VARNING Explosionsfara vid felaktigt batteribyte Anvand samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren Kassera anvant batteri enligt fabrikantens instruktion VAROITUS Paristo voi rajahtaa jos se on virheellisesti asennettu Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin Havita kaytetty paristo valmistajan ohjeiden mukaisesti NEDERLAND THE NETHERLANDS O Dit apparaat bevat een lithium batterij voor geheugen back up O Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur afdankt of de volgende Yamaha Service Afdeiing Yamaha Music Nederland Service Afdeiing Kanaalweg 18 G 3526 KL UTRECHT Tel 030 2828425 O Gooi de batterij niet weg maar lever hem in als KCA O This apparatus contains a lithium battery for memory back up O For the removal
7. ht noise into nearby radios and TVs If noise occurs relocate the affected equipment If the message WARNING LOW BATTERY appears when you turn on this unit contact your dealer as soon as possible about replacing the internal data backup battery The unit will still operate correctly but data other than the presets will be lost Before you replace the battery store your data to an ATA compliant PC flash storage card via the CS1D or store the data to the personal computer by connecting the computer to the PC CONTROL RS 232 C con nector on the DSP1D DSP1D EX The unit is equipped with the ground connector to avoid the risk of electrical shock Be sure to ground the unit before you insert the power plug into an AC outlet If the power cord has three pins and the ground con nector on the AC outlet is grounded the unit will be grounded effectively Thank you for choosing the DSP unit DSP1D DSP1D EX specifically designed for the Yamaha PM1D digital audio mixing system The DSP1D DSP1D EX is an engine controlled by the CS1D control surface Be sure to ask an authorized Yamaha service engineer to install the boards and set up the unit Never perform installation and setup by yourself The following optional boards can be installed in the DSP1D CIBTD Console interface board EMB1D Engine management board PDBID Patch DSP board GDBID Group DSP board EDB1D Effect DSP board IDB1D Input DSP bo
8. ly be dropped or the cabinet be damaged turn the power switch off remove the power plug from the AC outlet and contact your dealer If you continue using the unit without heeding this instruction fire or electrical shock may result If the power cord is damaged i e cut or a bare wire is exposed ask your dealer for a replacement Using the unit with a damaged power cord is a fire and electrical shock hazard Do not remove the unit s cover You could receive an electrical shock If you think internal inspection maintenance or repair is necessary contact your dealer Do not modify the unit Doing so is a fire and electri cal shock hazard When rack mounting the unit allow enough free space around the unit for normal ventilation This should be 10 cm behind and 20 cm above For normal ventilation during use remove the rear of the rack or open a ventilation hole If the airflow is not adequate the unit will heat up inside and may cause a fire This unit has ventilation holes at the rear and bottom to prevent the internal temperature rising too high Do not block them Blocked ventilation holes are a fire hazard Hold the power cord plug when disconnecting it from an AC outlet Never pull the cord A damaged power cord is a potential fire and electrical shock hazard Do not touch the power plug with wet hands Doing so is a potential electrical shock hazard The digital circuits of this unit may induce a slig
9. ns Windows 95 or Windows 98 to control the PM1D system from the PC Use a D sub 9 pin cross cable female to female to connect the RS 232 C port to the serial COM port on the PC The USB port is provided for future system expansion but it is not operative in the current software version WORD CLOCK IN jack 75 Q ON OFF switch and WORD CLOCK OUT jack The WORD CLOCK IN jack is used to provide word clock to the PM1D system from the connected exter nal device such as a clock generator Use the WORD CLOCK OUT jack to provide the word clock to the connected external device from the PM1D Use a BNC cable with an impedance of 75 Q for the WORD CLOCK IN OUT jacks The WORD CLOCK ON OFF switch is used to termi nate the word clock connection Basically if the DSP1D DSP1D EX is the last device of the word clock chain or if nothing is connected to the WORD CLOCK IN OUT jacks set this switch to ON CONSOLE 1 2 IN OUT jacks These jacks are connected to the CONTROL I O CONSOLE jacks of the CS1D control surface to trans mit or receive control signals For connection use a genuine Yamaha cable or a BNC cable with an imped ance of 50 Q REMOTE RS 422 connector This D sub 9 pin connector is used to control a con nected tape recorder or a hard disk recorder Serial commands can be transmitted through this connector to play or stop such a recorder This connector is provided for future system expan sion but it is not operative in the cu
10. pitch 68 pin connector female x 2 DIGITAL I O CONSOLE I O 1 2 RS 422 D sub half pitch 68 pin connector female x 2 CONTROL I O CONSOLE 1 IN OUT 0 225V 1 825V 50 Q BNC connector x 2 CONTROL I O CONSOLE 2 IN OUT 0 225V 1 825V 50 Q BNC connector x 2 REMOTE RS 422 RS 422 D sub 9 pin connector female GPI add ede D sub 25 pin connector female TIME CODE IN SMPTE format Nominal 10 dB 10 kQ XLR 3 31 type connector MIDI IN OUT THRU MIDI format 5 pin DIN connector x 3 PC CONTROL RS 232 C RS 232 C D sub 9 pin connector male PC CONTROL USB DN 3 3V B type USB connector WORD CLOCK IN TTL 75 Q ON OFF BNC connector WORD CLOCK OUT TTL 75 Q BNC connector Slots for IDB1D board Unit Input channel DPS1D INPUT 1 48 amp ST IN 1 4 DPS1D EX INPUT 1 96 8 ST IN 1 8 DSP1D IDB1D for expansion The DSP1D has an empty slot available for the IDB1D board E Dimensions 450 460 8 480 YAMAHA 399 2 408 7 a BI unit mm O Specifications and appearance are subject to change without notice for improvement For European Model Purchaser User information specified in EN55103 1 and EN55103 2 Inrush Current 31A Conformed Environment El E2 E3 and E4 YAMAHA CORPORATION Pro Audio Division 18 3 P O Box 3 Hamamatsu 430 8651 Japan
11. rrent software version GPI connector This connector is used to connect an external device that supports GPI General Purpose Interface such as a video editor to control the external device from the PMID system or to perform certain functions of the PMID system while controlling from the external device You can connect a custom made external switch here This connector is provided for future system expan sion but it is not operative in the current software version 1 TIME CODE IN connector OUTPUT 1 6 slot This balanced XLR3 31 connector receives SMPTE Use these slots to connect the INPUT connectors of an time code LTC for analog input from the external analog output unit AO8 series or DIO8 digital I O device The rated input level is 10 dB and the pin unit to output multi channel digital audio signals assignment is as follows from the DSP1D DSP1D EX Use a genuine Yamaha 1 ground 2 hot 3 cold half pitch 68 pin cable for connection 12 CONSOLE I O 1 2 slots 15 INPUT 1 10 slot Connect these slots to the DIGITAL I O CONSOLE Use these slots to connect the OUTPUT connectors of jacks of the CS1D control surface to transmit multi an analog input unit AI8 series or DIO8 digital I O channel digital audio signals Use a genuine Yamaha unit series to input multi channel digital audio signals half pitch 68 pin cable for connection to the DSP1D DSP1D EX Use a genuine Yamaha half pitch 68 pin cable for connection 13 CASCADE IN OUT slo
12. ts Use one of these connectors to cascade two DSP1D Ground connector DSP1D EX units to transmit multi channel digital Be sure to ground the unit to avoid the risk of electrical audio signals Use a genuine Yamaha half pitch 68 pin shock before you insert the power plug into an AC outlet cable to connect the CASCADE IN or OUT to the This product comes with a 3 pin power cord If the CASCADE OUT or IN of another DSP1D DSP1D ground connector of the AC outlet has already been EX grounded the unit will be grounded effectively by These connectors are provided for future system using the 3 pin power cord expansion but they are not operative in the current Grounding the unit is also effective for preventing software version hum and other noise E Specifications lt External sync gt 39 69 kHz 50 88 kHz lt Internal sync gt 44 1 kHz 48 kHz USA and Canada 120 V 60 Hz Others 230 V 50 Hz Sampling frequency Power supply Power consumption 170W Dimensions W x H x D 480 mm x 408 7 mm x 460 8 mm Weight 33 kg Operating temperature 10 35 C Fan circuit always fixed Accessories power cable 2 5 m x 1 Digital I Os UO connectors Level Type DIGITAL I O INPUT 1 10 RS 422 D sub half pitch 68 pin connector female x 10 DIGITAL I O OUTPUT 1 6 RS 422 D sub half pitch 68 pin connector female x 6 DIGITAL I O CASCADE IN OUT RS 422 D sub half
Download Pdf Manuals
Related Search