Yamaha Drums 36C User's Manual
Contents
1.2.
3. YAMAHA 430 8650 10 1 108 8568 2 17 TEL 03 5488 1684 FAX 03 5488 5087 i
4. 1 oo
5. 3 TEL 03 5488 1684 CBB00A CBF3OA CBBOOB CBF3OB BS8B00C
6. Stand Base Stand Base Caster Flat Washer Fully tightening the bolts without first loosely tightening the bolts intothe base pipes will result in damaged threadis in the base pipes and a misshapen stand Stand Base Base Pipe BS8B00C BS800C Stand Retrofit Kit sold separately x Base Pipe x 2 Both base pipes are the same 0 _ 556 6 6W66 6 6 6 0 _ 5 VW W W Q x4 x 4 x 4 Bolt x 4 Spring Washer x 4 Flat Washer x 4 for Base Pipe ee x x Lock Handle x 2 Flat Washer x 2 for Lock Handle lt Replacing the Wing Nuts 1 1 Remove the wing nuts and flat lt washers from the pivot shaft holder of your stand 2 Close the pivot shaft holder then put one
7. PD HI SBM ee MS A 0 CAUTION e Do not place the stand on uneven surfaces The stand may be 3 Do not run while moving the instrument The stand may come unstable and or overturn and result in possible injury become uncontrollable and crash into other objects re Do not lean on or ride upon the instrument stand The stand sulting in injury may move and cause a fall resulting in injury e Due to this instruments heavy weight two or more persons Do not rough play etc in the vicinity of the stand Bodily are necessary in the assembly of the stand harm may result by falling onto the stand Rough play may e Do not touch the moving parts Fingers and hands can get also result in the instrument being overturned Also keep caught in the moving parts children from pla
8. 9 3 Go 430 8650 10 1 TEL 053 411 4744 1 4 i 3 10 30 18 00 3 10
9. PO 4 F N
10. BS832C U0801620 BS836C U0801630 40 To mount your new bass drum on an older model stand CB800A series CBF30A series DB800B series CBF30B series please purchase the optional stand retrofit kit Sold sepa rately that fits your bass drum size inches and replace the Base Pipes x2 and Lock Handles x2 on your bass drum stand with those supplied in the kit To purchase the optional BS800C Stand Retrofit Kit sold separately please refer to the list below and contact the dealer from whom you purchased the bass drum Bass Drum Size inch Applicable Stand Retrofit Kit PartNo BS832C Stand Retrofit Kit U0801620 BS836C Stand Retrofit Kit U0801630 There is no retrofit kit available for the 40 inch bass drum We recommend the purchase of a new stand Exchanging the Base Pipes Base pipe should be replaced by at least two persons on a level surface 1 1 Remove the base pipes from your stand Re fer to the illus
11. pi 1 flat washer supplied with the retrofit kit 1 on the bolt and screw the end of the lock handle onto the bolt Loosen the lock handle enough to allow angle adjustment of the bass drum 3 Attach one more lock handle to the other 3 side of the bass drum stand 4 Position the bass drum at the desired angle then firmly tighten the lock handles on both sides of the bass drum stand to secure 4 Lock Handle Flat Washer dO Tighten lt Spring Washer Bolt Loosen Hexagonal Wrench Tighten
12. YAMAHA CONCERT BASS DRUM CB832C 836C 840C CB832CCB 836CCB 840CCB CBF32C 36C CBF32CCB 36CCB OWNER S MANUAL Thank you for purchasing the YAMAHA Concert Bass Drum Please read this Owner s Manual throughly before use Bass drum stand sold separately gt
13. s not used When mounting replacing new calf heads on the drum first wipe the area of the calf head that comes in contact with the shell edge using a slightly damp cloth then mount the head and tighten the tuning rods equally Tune the head after it has dried This procedure im proves contact between the calf head and the drum shell As long as the tension is not needlessly raised or lowered the calf head should maintain in good condition for a long period of time This warranty is valid only in Japan
14. tration below and use the hex wrench to completely remove the bolts used 1 to attach the base pipes to the stand along with the flat washers and spring washers BS800C 2 Insert the base pipes supplied with the BS800C 4 4 BS800C Stand Retrofit Kit into the holes on the stand base and use the hex wrench to partially tighten the four 4 bolts into the base pipe ends After all four 4 bolts are loosely tightened into the base pipes tighten all four bolts frmly Both base pipes are the same Please replace all bolts flat washers and Spring washers on your drum stand with those supplied with the retrofit kit
15. ying in the vicinity of the stand e Do not use the stand in the rain lf the stand becomes wet s Strong earthquakes may cause the stand to move about or use a soft dry cloth to wipe the stand as soon as possible overturn Stay away from the stands during earthquakes e Always use a soft dry cloth to clean the stand as a part of e Use the stand s casters to move the instrument on flat even periodic maintenance Never use thinner benzene or other surfaces only Lock the casters when the instrument is similar solvents to clean the stand not to be moved sthe instrument is frequently moved the bolts will become 1 In order to keep the bass drum from rotating on its axis loose over time Check bolts regularly and firmly tighten any firmly secure the bass drum in a vertical position in the loose bolts found stand 89VAM AH A 2 On inclined rough or gravel surfaces the instrument may overturn and or become uncontrollable YAMAHA CORPORATION PO Box 1 Hamamatsu Japan 0612 RO Printed in Japan lt Regarding the Use of Calf Heads gt As changes in temperature and humidity have a great effect on the tension of calf heads please pay attention to the following points lf possible tune the head just before playing As tension generally lowers when humidity is high slightly over tune the head The head may become warped if the head is loosened when the drum is not in use so please make sure head tension is maintained even when the drum i
Download Pdf Manuals
Related Search