Yamaha 02R96 Supplementary Manual
Contents
1. Note If you had been monitoring with the surround mode set to 6 1 and the monitor matrix mode set to 6 1 on 02R96 units with system software earlier than V2 1 the playback may not always be correct on V2 1 MONITOR MATRIX This is used to select the Surround Monitor Matrix In 6 1 Surround mode you can select 6 1 5 1 3 1 or ST In 5 1 Surround mode you can select 5 1 3 1 or ST In 3 1 Surround mode you can select 3 1 or ST When a down mix Monitor Matrix is selected you can attenuate signals by using the ATT parameters You can use the Surround Monitor settings in Stereo mode but Monitor Matrix is fixed to ST Note If you choose monitor matrix mode 3 1 you must set the following three attenuation amounts to the same value e ATTI for surround mode 3 1 e ATT4 for surround mode 5 1 e ATT5 for surround mode 6 1 These ATT values are not attenuators for down mixing rather they are used as monitor adjust ment attenuators for lowering the playback volume of the Ls Rs Ls2 and Rs2 speakers The following screen shows an example in 6 1 Surround mode and 3 1 Monitor Matrix mode 1 Initial Data aay O MONITOR E sT L ST SURROUND MONITOR SETUP a SURR MONITOR BASS MONITOR E MODE MATRIX MANAGE ALIGNMENT ROTATE at HOLY Ea ASURR SETUPZASURR PATC SURR LIB BASS MANAGEMENT You can set the filter and attenuator settings for each Surround Monitor Channel using eight preset Bass Managem2. 02R96 V2 1 Supplementary Manual 02R96 system software V2 1 contains the following changes from V2 0 gu MONITOR E MIX C A SOURCES J 8 Initial Data CONTROL ROOM SETUP J MIX C R SOURCES parameter added to Control Room Monitor page 137 A MIX C R SOURCES parameter has been added in the CONTROL ROOM SETUP page In V2 0 you could E assicni 2 choose one item from 2TR D1 D2 D3 Al or A2 asa Ei eusi monitor source plus other sources STEREO ASSIGN1 E2 Auxa or ASSIGN2 In V2 1 you can turn the MIX C R SOURCES parameter off to disable this simultaneous selection CONTROL ROOM DIMMER LEVEL MONO MIX MONITOR SOURCES parameter i initia Data SNS HONITOR agST L ST added to Surround Monitor page 138 A MIX MONITOR SOURCES parameter has been MIX MONITOR SOURCES added to the SURROUND MONITOR page In V2 0 you Da could simultaneously choose a BUS and SLOT as the monitor source but in V2 1 you can turn this parameter off to disable this simultaneous selection CEES SURROUND MODE MONITOR LEVEL dB SNAP TO SPL8S THX presets added to Surround Monitor page 139 141 Presets for the THX pm3 monitor system have been added to the bass management settings for surround monitor ing Several supplements have also been added regarding the surround monitor settings so please replace the cor responding pages with the following Configuring Surround Monit
3. ent modes The following presets are available Presets Parameters No Title HPF 1 2 3 LPF1 LPF2 ATT1 amp 2 AMP 1 DVD LFE80Hz 80 12 80 24 80 24 0 10 2 DVD LFE120Hz 80 12 120 42 80 24 0 10 3 Movie LFE80Hz 80 12 80 24 80 24 3 10 4 Movie LFE120Hz 80 12 120 42 80 24 3 10 5 Bypass THRU THRU MUTE 0 0 THXD THX DVD 80 12L 120 42 80 24L 0 10 THXF THX Movie 80 12L 120 42 80 24L 3 10 THXM THX Music 80 12L 120 42 80 24L 0 10 ATT1 Adjusts the level difference between LR and LsRs ATT2 Adjusts the level difference between C and Bs AMP Corrects the LFE channel level HPF1 3 Cut the low range so that the speakers supporting frequency ranges will not interfere with the sub woofer signals HPF1 2 Cut the high range so that the subwoofer s supporting frequency ranges will not interfere with other speakers signals Note If you select preset THXD or THXE you cannot change the parameters Ifyou select preset THXM you can switch AMP between 10 dB and 0 dB However you cannot change other parameters You can set the Bass Management parameters in the following ranges Parameters Range HPF 1 2 3 THRU 80 12 80 12L 80 24 80 24L LPF1 THRU 80 24 80 24L 120 42 LPF2 THRU 80 24 80 24L MUTE ATT 1 amp 2 0 to 12 dB 1 GB steps AMP O to 12 dB 1 GB steps The HPF 1 2 3 and LPF 1 amp 2 values indicate a cut off frequency and a fil
4. he above settings separately from when in other modes Tip The settings you make here can be stored in the surround monitor library U R G Pro Audio amp Digital Musical Instrument Division Yamaha Corporation 2004 Yamaha Corporation
5. is preset is the same as preset 2 mentioned above except that the output level of surround channels is set to 3 dB when the Monitor Matrix mode is 5 1 or 6 1 This preset is suitable for movie production 5 Bypass Use this preset not only for bass management but to bypass all parameters such as the LFE level amp LPF surround channel level etc To disable only the bass management select another preset then turn off the BASS MANAGE MENT ON OFF button E THX Presets The following presets have been approved by THX Ltd for use in THX pm3 Certified Stu dios They are designed to provide dedicated parameters for the proper playback of multi channel audio content in bass managed systems and to be compatible with subwoofer satellite type consumer systems Use of a THX preset does not permit a studio to use the designation THX pm3 Certified Studio The THX pm3 Studio Certification Program uses performance and design specifications to create calibrated environments for optimum sound and picture presentation For more information visit the THX website at http www thx com THXD THX DVD This preset is configured for DVD Video production Use this preset when mixing and or monitoring audio content not from a theatrical film source The parameters cannot be changed THXF THX Film This preset is configured for Film pre production Use this preset when mixing and or moni toring theatrical film based content such as a pre m
6. ix for film The parameters cannot be changed THXM THX Music This preset is configured for DVD Music production Use this preset when mixing and or monitoring multi channel music content including DVD Audio and SACD Only one parameter can be changed The LFE gain AMP can be set to 10dB default or OdB Select the level that complies with the standards of the target media Please note The LFE output gain on some DVD players receivers and or decoders may already be set to 10dB Select the 0dB setting only if the destination environment home theatre etc has the LFE gain set to 0dB Otherwise use the default setting e MONITOR ALIGNMENT ATT amp DLY ON OFF ise EL ENT These buttons are used to turn on and off the Monitor Align ment Attenuator and Delay parameters of all Surround speak ers The MONITOR ALIGNMENT diagram and Surround Channel Attenuator and Delay parameters which are dis played when either of these buttons are selected allow you to align the surround monitor speakers by attenuating and delaying Surround Channels as necessary The Attenuator parameters can be set gt 12 dB to 12 dB in 0 1 dB steps The Delay parameters can be set from 0 to 30 msec in 0 02 msec steps Note Please note that the above settings apply only to the signals being monitored They do not affect the normal bus outputs If you re monitoring in surround mode 6 1 and monitor matrix mode 6 1 you ll need to make t
7. oring Surround monitoring including speaker setup monitor matrix Bass Management and mon itor alignment is configured on the Surround Monitor Setup page 1 Use the MONITOR DISPLAY button to locate the Surround Monitor Setup page 1 Initial Data aay MONITOR E sT L ST SURROUND MONITOR SETUP Tax SURR MONITOR BASS MONITOR Gl MANAGE ALIGNMENT ATT HOLY MODE MATRIX Ea TASURR SETUPSISURR PATCHA SURR LIB Use the cursor buttons to select the parameters and use the Parameter wheel INC DEC buttons and ENTER button to set them SPEAKER SETUP These parameters are for setting the volume balance of the surround mon itor speakers Select the OSC Oscillator parameter and choose from PINK NOISE 500 2K pink noise through a 500 Hz to 2 kHz BPF 1K 1 kHz sinewave or 50 Hz 50 Hz sinewave Use the ON OFF button to turn the Oscillator on and off When on the Oscillator outputs a signal at 20 dB to the Surround Channels whose icons are highlighted You can turn on and off Oscillator output for speakers individually Speaker icons can be selected by using the cursor buttons The signal phase of the LFE Channel can be reversed by using the SW phase button When ROTATE is on the Oscillator signal is output by each speaker in turn in a clockwise direction 3 second signal 2 second pause SURR MODE This indicates the currently selected Surround mode which is set on the Sur round Mode page see page 85
8. ter response For example 80 12 means a cutoff frequency of 80 Hz and a filter response of 12 dB octave L means Linkwitz filter Other filters are Butterworth About the Presets 1 2 3 DVD LFE80Hz This is a preset optimized for DVD Video production The LFE playback bandwidth is set up to 80 Hz When using this preset we recommend that you use an external device to apply an LPF fc 80 Hz 24 dB oct to the LFE master source To monitor audio on DVD Audio or SACD discs change the LFE level AMP and LPF LPF1 to 0 dB and THRU respectively if necessary The LFE output gain on some DVD players and decoders may already be set to 10 dB To monitor the output from such devices change the LFE level AMP to 0 dB DVD LFE120Hz This is also a preset optimized for DVD Video production This preset is the same as preset 1 mentioned above except that the LFE playback bandwidth is set up to 120 Hz Use this preset to monitor standard LFE signals recorded on DVD Video discs that include the high end fre quency ranges 120 Hz Movie LFE80Hz This preset is the same as preset 1 mentioned above except that the output level of surround channels is set to 3 dB when the Monitor Matrix mode is 5 1 or 6 1 This preset is suitable for movie production When using this preset we recommend that you use an external device to apply an LPF fc 80 Hz 24 dB oct to the LFE master source 4 Movie LFE120Hz Th
Download Pdf Manuals
Related Search