Xantech 283D User's Manual
Contents
1. dhesive tape is included If you move the emitter to a different component use this tape to replace the current adhesive layer for the best adhesion e The shell though dark in appearance is transparent to infrared light allowing commands from a handheld remote control to pass through it This permits direct control of the equipment from a handheld remote as well as from the 283D BLACK IR OPAQUE EMITTER SHIELD An optional shield available from Xantech as model 28DES fits over the emitter head and the sensor window of the controlled component It prevents unwanted external IR signals from passing through or leaking past it 4 Adhesive Layer e Pai S Controlled Component Top View Emitter Shield and Emitter installed Side View over IR sensor window Use the 28DES when you want the equipment to respond only to the 283D such as in zone controlled systems CONNECTING THE EMITTERS Simply insert the mono mini plug of the 283D emitter into the EMITTERS or OUT jacks on any of the Xantech Connecting Blocks or Controllers e CAUTION DO NOT plug emitters into the IN OUT or HIGH OUT jacks on the 790 00 and 791 44 Connecting Blocks To do so will destroy the emitters e The 283D visible emitter will also indicate the presence of stray IR or RF interference by randomly blinking when no IR control signal is being sent Reposition the IR receiver of the interfering source to eliminate or reduce the random blinki2. ech Corporation Xantech Corporation shall not be liable for operational technical or editorial errors omissions made in this document
3. ng The more the random blinking is reduced the better the system will function S1ERGPS Saleliie Receiver To120VAC IR Sensor Unswitched Window 789 44 Lonnecting Glock i lt gt Emitter DWD OC Dood Emitter AV Rieoriver Eee Lia Frea i ia g F i o th x r EQUIPMENT CABINET CLOSET ETC 2910 SERIES If Peceiver Hand Held lt Remote Limited Warranty Xantech warrants its products to be free of defects in materials or workmanship This is a Limited Lifetime warranty from the date of purchase by the original consumer Any products returned to Xantech and found to be defective by Xantech within the warranty period will be repaired or replaced at Xantech s option at no charge Xantech will not be responsible for the actual cost of installation or removal of the product nor for any incidental or consequential damages Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you This warranty gives you specific legal rights You may have additional legal rights that vary from state to state Xantech Corporation 13100 Telfair Ave 2F Sylmar CA 91342 Xantech com Installation Instructions 283D 2008 Xantech Corporation Document 08905167B This document is copyright protected No part of this manual may be copied or reproduced in any form without prior written consent from Xant
4. xantectn MODEL 283D Blink IR Designer Emitter INSTALLATION INSTRUCTIONS o N42777 31548 12 DESCRIPTION The 283D Blink IR Designer Emitter contains a small Infrared LED housed in a miniature designer styled black appearing injection molded plastic shell Unlike other emitters the 283D emits visible red light in addition to IR infrared control signals when activated by IR commands sent to it by IR receivers or other Xantech controllers The 283D is designed to be installed directly on the IR sensor window of the controlled device Side View E NOTE White striped 44 side is positive 3 5mm mono i mini plug j Top View y e n m 7 FT ne 3 FTA 5 8 INSTALLATION ATTACHING THE EMITTERS TO IR SENSOR WINDOWS e Each emitter has a clear adhesive layer on the bottom flat surface of the shell e Simply peel off the adhesive cover and affix the emitter to the center of the IR sensor window on the controlled component s front panel ie IR amp Red Ligh pe Output z p ra IR amp Red a Light Output AIN Compound Side Emitter t N Shell Clear adhesive ayer epiace if necessary with a short piece of th 1e 2 sided tape supplied panaire a e In some cases it may be difficult to find the location of the IR sensor on the component Consult the owner s manual of the unit or the manufacturer for the exact IR sensor window location e Double sided a
Download Pdf Manuals
Related Search