Home

X10 Wireless Technology MS15A User's Manual

image

Contents

1. Release and immediately press the button the desired number of times for the Unit Code you want to set Hold the button for 3 seconds on the last press The red light blinks back the number of times for the code you set Release the button X10 com a Div of X10 Wireless Technology Inc 3824 North 5th St Suite C North Las Vegas NV 89030 1 800 675 3044 www x10 com DR MS15A 7 01 To change the House Code that the ActiveEYE transmits Press and hold the House On button under the battery compartment lid the red light flashes first and then blinks the current setting once for A twice for B etc Release and immediately press the button the desired number of times for the House Code you want to set once for A twice for B etc Hold the button for 3 seconds on the last press The red light blinks back the number of times for the code you set Release the button To turn additional lights on when it gets dark The ActiveEYE can send signals when it detects dusk and dawn so it can turn a light on when it gets dark and turn it off when it gets light in addition to turning lights on when it detects motion To have it turn a light on at dusk and off at dawn plug the light into an X10 Module and set it to the same Housecode as the ActiveEYE and to a Unit Code that is one number higher than the Unit Code of the module that turns on when motion is detected I E if the ActiveEYE turns on A1 when it detects motion it will turn on A2 when it gets d
2. Set Up and Operating Instructions for ActiveEYE Motion Detectors Models MS15A Indoor and MS16A Indoor Outdoor The ActiveEYE Motion Detector sends Wireless Radio Frequency RF signals to an X10 Transceiver RR501 or TM751 The receiver then passes the signals onto your house wiring to turn on lights appliances or X10 wireless cameras around your home You plug your lights and appliances into X10 Modules sold separately You can set the ActiveEYE to turn the lights or cameras off after motion stops You can set this for a preset time of 2 4 8 minutes etc see below for more details or you can set any variable delay you like 1 minute min to 60 minutes max using the NEW easy to set dial on the top of the unit The ActiveEYE also works with the CM11A Two Way Computer Interface to initiate macros routines so you can set up a coming home routine which is initiated by the ActiveEYE as soon as it sees you Note The default state is to turn lights on when the ActiveEYE detects motion at all times even if it s not dark But you can also set it to turn lights on when it detects motion only at night It can also turn lights on at dusk and off at dawn but this feature is disabled by default see other side of sheet to enable If you enable this feature care should be taken to place the ActiveEYE where it sees plenty of sunlight during the day such as near a window If you place it in a dark corner it might not be able to tell the d
3. ark and turn it off when it gets light You then need to enable this feature see below for details Note If you enable this feature and use the ActiveEYE to control X10 wireless cameras care should be take NOT to set any cameras to the code that the ActiveEYE sends at dusk and dawn Unit Code 1 Otherwise you will find your cameras will be turned off at dawn To set whether you want the ActiveEYE to transmit EVERY time it sees motion or only at night and to enable or disable the Unit Code 1 function to turn lights on off at dusk dawn Press the Unit Off button once The red light flashes Then press and hold the House On button The green light turns on 3 seconds later the ActiveEYE reports its dusk dawn setting as follows The red light blinks once if the ActiveEYE is set to detect motion at all times and does not turn Unit Code 1 ON at dusk and OFF at dawn The red light blinks twice if the ActiveEYE is set to detect motion only when it s dark and does not turn Unit Code 1 ON at dusk and OFF at dawn The red light blinks three times if the ActiveEYE is set to detect motion at all times and does turn Unit Code 1 ON at dusk and OFF at dawn The red light blinks four times if the ActiveEYE is set to detect motion only when it s dark and does turn Unit Code 1 ON at dusk and OFF at dawn To change this Press the Unit Off button once The red light flashes Then press and hold the House On button The green light turns on 3 secon
4. ds later the ActiveEYE reports its dusk dawn setting as listed above Release and immediately press the House On button 1 2 3 or 4 times for the setting you require as above Hold the button for 3 seconds on your last press The red light then reports the setting with 1 2 3 or 4 blinks NOTES After replacing batteries you need to wait 30 seconds before the ActiveEYE will see any motion After a transmission you need to wait 10 seconds before the ActiveEYE will see you The default House and Unit Code transmitted when motion is detected is A 1 ON The default for motion detection is detect at all times day and night The default time out after which OFF is sent default A 1 OFF is Analog i e the setting on the dial The default House and Unit Code transmitted when dusk dawn is sensed is Unit Code 1 i e A 2 ON at dusk A 2 OFF at dawn but this feature is disabled by default see above to enable it F C C CAUTION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUD ING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION NOTE NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS ANY CHANGES MADE TO THE UNITS WILL VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT DR MS15A 7 01
5. ifference between day time and night time Care should also be taken not to place the ActiveEYE near the light it is controlling otherwise when the light turns on it might fool the ActiveEYE into thinking it s daytime Remove the screw from the front of the unit MS16A only Remove the battery cover and install two AAA alkaline batteries Leave the cover off for now The unit defaults to Housecode A and Unit Code 1 and it defaults to see motion at all times day and night so plug in an X10 RF Transceiver model RR501 or TM751 each sold separately and set it to Housecode A Plug a lamp into an X10 Lamp Module sold separately and set it to Housecode A and Unit Code 1 Plug the module into any AC outlet To test the ActiveEYE Press the House button once The ActiveEYE transmits the device ON RF signal and the red light flashes Press the Unit button once The ActiveEYE transmits the device OFF RF signal and the red light flashes The default setting is Al Replace the battery cover Place the ActiveEYE on a shelf or mount it on a wall at least 6 feet above the ground Let it settle for a minute and then walk past it The lamp connected to any X10 Module set to A1 turns on The light turns off a short time later as long as no motion has been detected The default time is the setting on the dial on the top of the unit so you can adjust this to suit your preference 1 minute min to 60 minutes max You will also see later that y
6. ou can set this for a specific predetermined time For outdoor use remove the batteries screw the MS16A to a wall and replace the batteries Refit the cover and screw To change the delay after motion is detected before an OFF code is transmitted Press the House On button once The red light flashes Press and hold the Unit Off button The green light turns on 3 seconds later the red light reports its delay setting as follows 1 blink for Analog setting i e the setting on the dial on the top of the unit 2 blinks for 2 minutes 3 blinks for 4 minutes 4 blinks for 8 minutes 5 blinks for 16 minutes 6 blinks for 32 minutes 7 blinks for 64 minutes 8 blinks for 128 minutes 9 blinks for 256 minutes To change this Press the House On button once The red light flashes Press and hold the Unit Off button The green light turns on 3 seconds later the red light reports its delay setting as listed above Release and immediately press the Unit Off button the number of times for the delay you want as listed above Hold the button pressed for 3 seconds on the last press The red light then reports the setting with the appropriate number of blinks as above Release the button Note for settings of 2 blinks or higher the dial on the top of the unit is disabled To change the Unit Code that the ActiveE YE transmits Press and hold the Unit Off button under the battery compartment lid the red light flashes first and then blinks the current setting

Download Pdf Manuals

image

Related Search

Related Contents

Philips InStyle Ceiling light 37926/17/16  Brodit Passive holder  Coby DP240  STA™ Single Tooth Anesthesia System  Cineo Maverick User Guide.indd  Garmin PAV80 Car Stereo System User Manual    マルチファンクション モバイルバッテリー マルチファンクション モバ  新旧製品比較資料  NW-HD5H  

Copyright © All rights reserved.
Failed to retrieve file