Whirlpool 4373526 User's Manual
Contents
1. bottle Do Not cut this tubing or add tubing between pump and water bottle Do Not remove clamp on end of tubing that connects inner tubing to outer tubing Suggested locations e Under the sink Cabinet next to refrigerator an et et Determine where you will need to run water lines and the length of tubing that will be needed If more tubing is needed than what is supplied tubing Part No 4319151 and tubing connectors Part No 4319153 can be obtained from your dealer or authorized parts distributor 3 i Attach bottle cap to water bottle Push the tubing into the water bottle until the end of the tubing reaches the bottom of the bottle Do Not remove clamp from end of tubing Insert one end of the outlet tubing into connector located on outside of pump as far as it will go If tubing needs to be adjusted push connector in and pull tubing out Panel B refrigerator Cut tubing to 5 Route the tubing to the E length needed 6 Plug power supply cord into earthed electrical outlet Press the pump switch to the I position Run enough water through refrigerator to fill a glass or other container Check all connections for leaks If a connection leaks push in collet and remove tubing Cut off 1 3cm 1 2 of tubing and reinsert into connector If unit is connected ONLY to a refrigerator icemaker the icemaker will have to call for water before pump can be2. checked for leaks Use and Care Information The water pump operates automatically when dispenser is operated When the dispenser is released the water pump automatically stops operating When water bottle empties during use Pressurized air is expelled through dispenser when water bottle is empty 1 Stop dispensing from the refrigerator x a Press the switch on the a water pump to the O position 3 a Remove bottle cap from water bottle Replace empty water bottle Attach bottle cap to full water bottle Press the switch on the water w PUMP to the I position If water bottle empties while unattended the pump will run for 2 1 2 minutes and then automatically shut off 1 Press the switch on the water E pump to the O position m Remove bottle cap from water bottle Replace empty water bottle Attach bottle cap to full water bottle 3 Press the switch on the water E pump to the I position If water system is exposed to temperatures below 0 C 32 F the system must be drained Remove tube from bottle Open alll outlets and run pump to inject air through all outlets Cleaning and sanitizing system System should be cleaned after extended periods of non use 1 Add one half teaspoon of m chlorine bleach to one gallon of water 2 Insert tube into solution and start mw pump Open all outlets to fill system with m solution Let stand five minutes 4 Flush syst
3. Installation Instructions Part No 4373526 IMPORTANT Read and save Pure Delivery Water System Home Appliances Before you start Check location where water pump will be installed Proper installation is your responsibility Make sure you have everything necessary for correct installation The serial rating information is located on the base of pump Important Observe all governing codes and ordinances Earthed electrical outlet is required See Electrical requirements Water connections to pump Do Not require sealing compounds to prevent leaking water bottle tubing water bottle instruction Pe water pump switch WARNING Personal Injury Hazard Do Not use water pump to pump water Clean system after extended periods of non use result in personal injury to refrigerator any other liquids Use only for bottled Failure to follow these instructions may WARNING Electrical Shock Hazard It is the customer s responsibility e To contact a qualified electrical installer e To assure that the electrical installation is adequate and in conformance with National Electrical Codes and all local codes and ordinances Failure to do so could result in fire electrical shock or other personal injury CAUTION Property Product Damage Do Not store water bottle and water pump in an area where temperatures fal
4. del number which is located on the serial rating plate on the base of the pump ONE YEAR FULL WARRANTY From date of purchase Replacement parts and repair labor to correct defects in materials or workmanship Service must be provided by an authorized Whirlpool International distributor or their appointed dealer or service company Whirlpool Will Not Pay For A Service calls to 1 Correct the installation of the pump 2 Instruct you how to use the pump 3 Replace house fuses circuit breakers or correct house wiring B Repairs when pump is used in other than normal use C Damage resulting from accident alteration misuse abuse improper installation or installation not in accordance with local electrical codes Whirlpool does not assume any responsibility for incidental or consequential damages Panel C lt gt Whirlpool CORPORATION Part No 4373526 1992 Whirlpool Corporation Prepared by Whirlpool Corporation Benton Harbor MI 49022 Printed in U S A
5. em with water until E chlorine is removed Troubleshooting Cromen Joass O o ton Cid Water pump cycles on and off Water pump does not run Water pump operates continuously until motor timer stops motor Air in system Water leaks at one or more outlet connectors Electrical power not being supplied Water bottle is empty Water bottle is empty Air leak in water bottle to pump tubing e Check all fittings and water pump connections for leaks e Push in connector and remove tubing Cut off 1 3cm 1 2 of tubing and reinsert into connector e Do Not cut water bottle to pump tubing e Check that power supply cord is plugged into outlet e Check if circuit breaker has tripped or if fuse has blown Check to see if water bottle is empty Replace water bottle according to instructions e Press switch on the water pump to O position Then press the switch to the l position to reset motor timer Replace water bottle according to instructions e Check that tubing in water bottle is touching bottom of bottle If tubing is too high it will take in air e Check that tubing is tightly pushed in place inside water pump connector Pure Delivery Water Pump Warranty Length of Warranty Whirlpool Will Pay For If you need service Call your authorized Whirlpool International Distributor or their appointed dealer or service company When you call you will need the pump mo
6. l below 0 C 32 F Failure to follow these instructions may result in property or product damage Tools needed for installation adjustable 7 knife or wrench IE tubing cutter Parts supplied foe hci ation bottle cap twist ti we f this end is factory assembled to pump yy y 1 4 outside diameter 3 8 outside tubing diameter tubing Parts not supplied for installation e fittings to connect e If additional tubing is 1 4 O D tubing to required you will need refrigerator inlet tubing connector Part No 4319153 and 1 4 O D tubing Part No 4319151 Electrical requirements a WARNING Electrical Shock Hazard Electrical earth is required on this appliance If cold water pipe is interrupted by plastic non metallic gaskets or other insulating materials Do Not use for earthing e Do Not earth to a gas pipe e Do Not modify the power supply cord plug If it does not fit the outlet have a proper outlet installed by a qualified electrician e Do Not have a fuse in the neutral or earthing circuit A fuse in the neutral or earthing circuit could result in electrical shock Do Not use an extension cord with this appliance If codes permit and a separate earthing wire is used it is recommended that a qualified electrician determine that the earthing path is adequate Panel A e Check with a qualified electrician if you are in doubt as to whether the a
7. ppliance is properly earthed e This appliance is equipped with a power supply cord having a 3 prong earthing plug To minimize possible shock hazard the cord must be plugged into a mating 3 prong earthing type wall receptacle earthed in conformance with National Electrical Codes and all local codes and ordinances See Figures 1 and 2 If a mating wall receptacle is not available it is the personal responsibility and obligation of the customer to have a properly earthed 3 prong wall receptacle installed by a qualified electrician Failure to follow these instructions could result in a serious injury or death A fused electrical supply is required Time delay fuse or circuit breaker is recommended It is recommended that a separate circuit serving only this appliance by provided Schuko earthing type wall receptacle S Sorang earthing plug Power supply cord Figure 3 prong earthing type wall receptacle Finn 3 prong earthing plug earthing prong power supply cord Figure 2 Now start With pump in room where it will be installed 1 g Determine where you wish to locate water pump and water bottle The water bottle and water pump should be installed on the same level The water bottle and water pump must be located close together since the tubing connecting the pump to the water bottle is 1 8m 6 feet long Use existing tubing between water pump and water
Download Pdf Manuals
Related Search