Weider B121 User's Manual
Contents
1. MEDALLION ASSEMBLY INSTRUCTIONS REPLACEMENT PARTS WEIDER HEALTH AND FITNESS 21100 Erwin Street Woodland Hills California U S A 91367 TABLE CONTENTS D M REPAIR PARTS AND SERVICE PP gt 20 gt STEP 1 FRAME ASSEMBLY STEP 2 BACKREST ASSEMBLY STEP 3 ATTACHING BACKREST AND SEAT STEP 4 ATTACHING LEG CURL sp gO MEDALLION rants usr 6 21 89 12 MAIN FRAME BRACE L BRACKET 23 6128 05 2 708 288 ze PART REO NO 2 lt 2 ae 3 FRONT SUPPORT 21 CO171 A23 4 LEG CURL 5 BACKREST 1 CO343 A23 6 ptt pap pan kd 8 FOAM PAD 4 CO425 A05 BACKREST ADJ BAR 1 C6045 A05 10 LONG ANGLE IRON 72 C6113 A23 11 UPRIGHT BRACE 1 6128 05 2 3 4 ROUND PLASTIC 4 8004 8005 8070 1 1 4 SQUARE PLASTIC 8069 1 HH 5017 0 1 4 20 X 3 4 MACHINE SCREW 6 5 16 20 1 3 4 HEX HEAD BOLT 2 2 HH 5048 gt 5 16 20 X 2 1 4 HEX HEAD 2 HH 5035 UPRIGHT DECAL 2 DE 4059 I 1 CMM 1070 BETEGNE GET EE m NSTRUCTION MANUAL Be REPAIR PARTS AND SERVICE ALL OF THE PARTS FOR THE WEIGHTBENCH CAN BE ORDERED FROM WEIDER HEALTH AND FITNESS PARTS SER2. VICE DEPT 900 WEST ST JOHN ST OLNEY ILL 62450 WHEN ORDERING PARTS WILL BE SENT AND BILLED AT THE CURRENT PRICES PRICES MAY BE SUBJECT TO CHANGE WITHOUT NOTICE STANDARD HARDWARE ITEMS ARE AVAILABLE AT LOCAL HARDWARE STORES TO OBTAIN PARTS DO NOT GO BACK TO THE STORE WHERE YOU PURCHASED THIS UNIT IF YOU FIND THIS PRODUCT TO HAVE EITHER A DEFECTIVE PART OR A MISSING PART WRITE THE ABOVE ADDRESS OR PHONE CUSTOMER SERVICE AT 3 800 225 0653 ALWAYS INCLUDE THE FOLLOWING INFORMATION WHEN ORDERING PARTS MODEL NO NAME OF PART ORDERING NUMBER B121 STEP 1 FRAME ASSEMBLY Begin by inserting 2 SQUARE PLASTIC CAPS 0 into UPRIGHT 1 Align bolt holes on MAIN FRAME 2 and FRONT SUPPORT 3 Secure with 1 HEX HEAD BOLT and 1 LOCK NUT J With UPRIGHT 1 standing lower u bracket of MAIN FRAME 2 onto upright crossmember Align bolt holes and secure with 2 HEX HEAD BOLTS H and 2 LOCK NUTS 3 Align bolt holes of UPRIGHT BRACE 11 with the top holes of the hole patterns located on bottom end of UPRIGHT 1 and then through top hole of L BRACKETS 13 Secure with 2 HEX HEAD BOLTS R and 2 LOCK NUTS J inger tighten only Align bottom holes of both L BRACKET 1 UP and secure with HEX HEAD BOLTS H and LOCK NUTS J Align bolt hole on MAIN FRAME BRACE 2 with center hole on UPRIGHT BRACE 11 Secure with HEX HEAD BOLT N and LOCK NUT J ign bolt hole on MAIN FRAME BRACE with hole
3. nd align bolt holes Secure with HEX HEAD BOLT F and LOCK NUT 6 Repeat the following instructions until all PAD BARS 7 and FOAM PADS 8 are in place First slide PAD BAR 7 through proper hole in LEG CURL 4 until equal amounts of bar are on both sides of LEG CURL 4 Apply a small amount of liquid dish detergent to both ends of PAD BAR to aid in the follow ing step Slide FOAM PAD f onto each end of PAD BAR 7 and insert ROUND PLASTIC A into each end of PAD BAR 7 Insert UAR into SQUARE PLASTIC end of LEG CURL 4 Insert ROUND PLASTIC into weight pin on LEG CURL Place COVER CAP over rear extended piece of weight pin WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM IT IS ADVISABLE TO HAVE PHYSICAL EXAMINATION BY YOUR PHYSICIAN BEFORE YOU ENTER ANY EXERCISE PROGRAM FOR YOUR OWN SAFETY DO NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION CHILDREN AND HANDICAPPED PERSONS SHOULD NOT USE ANY EXERCISE EQUIPMENT WITHOUT A QUALIFIED PERSON IN ATTENDANCE TRAIN WITH A PARTNER 15 RECOMMENDED THAT AN INDIVIDUAL SHOULD NOT WORKOUT WITHOUT A TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED
4. on MAIN FRAME 2 and secure with HEX HEAD BOLT M and LOCK NUT J Insert 2 SQUARE PLASTIC CAPS into FRONT SUPPORT 3 Tighten all bolts m LOOSEN OR 2 TURNS STEP 2 BACKREST PREPARATION Turn BACKREST 5 over to expose work area Both LONG ANGLE IRONS 10 have been fastened to BACKREST 5 for shipment One long angle iron must be loosened in order to assemble BACKREST 5 to main frame pivot The lower MACHINE SCREW K must be removed while the upper rod MACHINE SCREW is only loosened The LONG ANGLE IRON 10 now swing freely from the lower end of BACKREST 5 3 STEP 3 ATTACHING BACKREST 8 SEAT BACKREST To aid in attaching Backrest first slide the BACKREST ADJ BAR 9 through one of the hole patterns in the uprights With LONG ANGLE IRON 10 free lower BACKREST 5 to main frame pivot rod Slide the secured LONG ANGLE IRON 10 onto one side of pivot Swing the free LONG ANGLE IRON 10 back to its original osition and onto the o posite end of the pivot rod See etail A Replace MACHINE SCREW k that was removed in Step 2 and tighten all machine screws SEAT With SEAT 6 right side up lower SEAT 6 to MAIN FRAME 2 Align bolt holes and fasten with 2 MACHINE SCREWS K and 2 FLAT WASHERS P Tighten all machine screws STEP 4 ATTACHING LEG CURL pe gt Place LEG CURL 4 between BRACKETS P leg curl brackets on main frame a
Download Pdf Manuals
Related Search