Weider B460 User's Manual
Contents
1. ASSEMBLY INSTRUCTIONS REPLACEMENT PARTS WEIDER HEALTH AND Ay 21100 ERWIN STREET WOODLAND HILLS CALIFORNIA U S A 91367 TABLE OF CONTENTS Ene 17 Parts List pf 2 Repair Parts and Servico 72 gt Frame Assembly Step Backrest amp Seat Preparation CF Step 3 Connecting Seat to Main Frame 4 Step 4 Replacement of Short Angle Iron steps Leg Curl Assembly 8 STEP 1 FRAME ASSEMBLY Insert 2 SQUARE PLASTIC CAPS K into base of UPRIGHT 1 Attach BASE FRAME 2 to UPRIGHT 1 by aligning bolt holes and inserting 2 HEX HEAD BOLTS A and securing with 2 LOCK NUTS B Lower MAIN FRAME 3 to the base frame front bracket Secure with HEX HEAD BOLT A and LOCK NUT B Align bolt holes on rear bracket of MAIN FRAME 3 with bolt holes on crossmember on UPRIGHT 1 Secure with 2 HEX HEAD BOLTS A and 2 LOCK NUTS B Tighten all bolts Insert 2 SQUARE PLASTIC CAPS K into BASE FRAME 2 STEP 2 BACKREST AND SEAT PREPARATION Turn assembled backrest and seat over to expose work area Remove 2 MACHINE SCREWS R from seat and remove 1 SHORT ANGLE IRON 12 This preparation must be done in order to connect the seat to the main frame 3 STEP 3 CONNECTING SEAT TO MAIN FRAME To aid in this assembly first slide BACKREST ADJUST BAR 15 into one of the hole patterns on UPRIGHT 1 Turn BACKREST 4 and SEAT 5 assembly right side up and lower t2. P L into LEG CURL ADJUSTER 7 STEP 6 LEG CURL With assembled leg curl extended slightly forward lower LEG CURL ADJUSTER 7 into main frame tube LOCKING PIN H is used to position the height of the leg curl assembly Slide PAD BAR 9 through top hole in LEG CURL ADJUSTER 7 until equal amounts of PAD BAR 9 are on both sides Slide FOAM PAD 10 onto each end of PAD BAR 9 Insert ete CAP M into each end of PAD SPP mets tee econ STEP 7 ADJUSTABLE UPRIGHTS AND LOCKING PINS Slide ADJUSTABLE UPRIGHTS 14 into proper position in UPRIGHT 1 LOCKING PINS H are used to adjust the height of the ADJUSTABLE UPRIGHTS 14 LOCKING PIN J is used to lock the LEG CURL 8 while doing specific exercises
3. o MAIN FRAME 3 Slide the fastened SHORT ANGLE IRON 12 over the front pivot pin on the MAIN FRAME 3 Align the SEAT ADJUSTMENT T 6 with the proper slot on the MAIN FRAME 3 and lower through slot Secure SEAT ADJUSTMENT 6 by inserting 1 HEX HEAD BOLT E through bottom hole and secure with 1 LOCK NUT F EYELET PIN G is used in the remaining holes of the SEAT ADJUSTMENT T 6 to adjust the desired height of the seat STEP 4 REPLACEMENT OF SHORT ANGLE IRON To aid in this assembly EYELET PIN G should be placed so that the highest possible posi tion of the seat is achieved Slide SHORT ANGLE IRON 12 over pivot pin on SEAT ADJUST MENT T 6 and front pivot pin on MAIN FRAME 3 Replace 2 MACHINE SCREWS 12 that were removed in Step 2 STEP 5 LEG CURL ASSEMBLY Position LEG CURL 8 between leg curl brackets on LEG CURL ADJUSTER 7 Secure with 1 HEX HEAD BOLT C and 1 LOCK NUT D Do not over tighten Repeat the following instructions until all leg curl parts are in place First slide PAD BAR 9 through proper hole in LEG CURL 8 until equal amounts of pad bar are on both sides of LEG CURL 8 Slide FOAM PAD 11 onto each end of PAD BAR 9 Insert ROUND PLASTIC CAP M into each end of PAD BAR 9 Insert SQUARE PLASTIC CAP K into end of LEG CURL 8 Insert ROUND PLASTIC CAP N into weight pin on LEG CURL 8 Place COVER over rear extended piece of weight pin Insert SQUARE PLASTIC CA
Download Pdf Manuals
Related Search