Weider B220 User's Manual
Contents
1. ALWAYS include the following information when ordering parts eModel Number eName of Part e Ordering Number 2 STEP 1 FRAME ASSEMBLY Insert 2 SQUARE PLASTIC CAPS M into base of UPRIGHTS 1 Stand UPRIGHTS 1 into proper position while preparing the rest of the frame Align bolt holes of Main Frame Lower Bracket with bolt holes on FRONT SUPPORT 3 Join the two pieces with 2 HEX HEAD BOLTS A and 2 LOCK NUTS C Lower Main Frame Upper Bracket over crossmember on UPRIGHTS 1 and align bolt holes Secure with 2 HEX HEAD BOLTS A and 2 LOCK NUTS C Tighten all bolts Insert 2 PLASTIC CAPS N into both ends of FRONT SUPPORT 3 Insert 1 CAP N into top of MAIN FRAME 2 tube SEAT 2 BACKREST amp SEAT PREPARATION Turn assembled Backrest and Seat over to expose work area Remove 2 MACHINE SCREWS R from Seat and remove 1 SHORT ANGLE IRON 7 This preparation must be done in order to connect Seat to Main Frame STEP 3 CONNECTING SEAT TO MAIN FRAME To aid in this assembly first slide BACKREST ADJUSTMENT BAR 13 into one of the hole patterns on UPRIGHTS 1 Turn BACKREST 4 and SEAT 5 assembly right side up and lower to MAIN FRAME 2 Slide the fastened SHORT ANGLE IRON 7 over the front pivot pin on the MAIN FRAME 2 Align the SEAT ADJUSTMENT T 8 with the proper slot on the main frame and lower through slot Secure SEAT ADJUSTMENT T 8 by BER NUT UE HEX HEAD BOLT F through bottom hole2. ASSEMBLY INSTRUCTIONS REPLACEMENT PARTS WEIDER HEALTH AND FITNESS 21100 ERWIN STREET WOODLIN HILLS CALIFORNIA U S A 91367 TABLE CONTENTS STEP4 REPL SHORT ANGLE IRON STEP 5 LEG CURL ASSEMBLY STEP 6 ADJ UPRIGHTS amp LOCKING PIN WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM IT IS ADVISABLE TO HAVE A PHYSICAL EXAMINATION BY YOUR PHYSICIAN BEFORE YOU ENTER ANY EXERCISE PROGRAM FOR YOUR OWN SAFETY DO NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION CHILDREN AND HANDICAPPED PERSONS SHOULD NOT USE ANY EXERCISE EQUIPMENT WITHOUT A QUALIFIED PERSON IN ATTENDANCE TRAIN WITH A PARTNER 15 RECOMMENDED THAT AN INDIVIDUAL SHOULD WORKOUT WITHOUT A TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED 220 PARTS LIST DIAGRAM NO 1 UPRIGHT 1 CA07 0209 2 MAIN FRAME 1 07 017 __ 9 FRONT SUPPORT 1 CAO7 0118 4 BACKREST 1 CA07 0318 51151121 CA07 0319 6 LONG ANGLE IRON 2 CAO7 6057 SHORT ANGLE 2 CAO7 6058 8 SEAT ADJUSTMENT T 1 07 6059 9 J LEGCURL J O1 07 0119 100 PAD BAR 32 07 6056 11 FOAM PADS 1 4 01 42000 12 ADJUSTABLE UPRIGHT 2 CAO7 0210 13 BACKREST ADJ BAR 1 w
3. and secure with 1 LOCK NUT EYELET PIN P is used in the remaining holes of the SEAT ADJUSTMENT T 8 to adjust the desired height of the seat STEP 4 REPLACEMENT OF SHORT ANGLE IRON To aid in this assembly PIVOT PIN P should be placed so that the highest possible posi tion of the Seat is achieved Slide SHORT ANGLE IRON 7 over pivot pin on SEAT ADJUST MENT T 8 and front pivot pin on MAIN FRAME 2 Replace 2 MACHINE SCREWS that were removed in Step 2 LEG CURL BRACKETS STEP 5 LEG CURL ASSEMBLY Position LEG CURL 9 between leg curl brackets Secure with HEX HEAD BOLT B and LOCK NUT D Do not over tighten Repeat the following instructions until all leg curT parts are in place First slide PAD BAR 10 throught proper hole in LEG CURL 9 until equal amounts of bar are on both sides of LEG CURL 9 Slide on FOAM PAD 11 onto each end of PAD BAR 10 Insert PLASTIC CAP K into each end of PAD BAR 10 Insert SQUARE PLASTIC CAP N into end of LEG CURL 9 Insert ROUND PLASTIC CAP H into weight pin on LEG CURL 9 Place COVER CAP J over rear extended piece of weight pin STEP 6 ADJUSTABLE UPRIGHTS amp LOCKING PIN Slide UPRIGHTS 12 into upright frame adjust able backrest bar is used to adjust not only the position of the ADJUSTABLE UPRIGHTS 12 but also the height of the backrest LOCKING PIN G is used to lock the LEG CURL 9 for doing specific exercises
4. CA06 6054 F RRE HSE REE EEG Cee ee en nS FSS FOSS ew GREEN HARDWARE BAG 1 CA07 5780 546 18x21 HEX HEAD BOLT 4 5199 3 g 16x 2 HEX HEAD BOLT 11 HH 5018 C 1546 68 LOCK NUT 4 HH 5012 D 38 6 LOCK NUT 1 HH 5013 E _ 4 20 LOCKNUT X 1 HH 5011 J T 17 20 54 MACHINESCREW 1 HH 5032 GI LOCKING PIN 1 WW 012 H TRD PLASTIC CAP 1 AA 800 mv 1 RD COVER CAP 1 AA 8070 K X 34RD PLASTIC 4 8004 9 M 2SQ PLASTIC 2 A800 N 114SQ PLASTIC CAP 4 AA 800 TR 14 20 x 3 4 MACHINE SCREW 8 5022 _ UPRIGHT DECAL RIGHT 1 DE 4008 2 2 PRIGHT DECAL LEFT 1 DE 4009 INSTRUCTION MANUAL 1 18488 MEM E CN EE FER MIENNE MM ERR EE NE MEN REPAIR PARTS AND SERVICE of the parts for the Weightbench be ordered from Weider Health and Fitness Parts Service Dept 900 West St John St Olney Ill 62450 When ordering parts will be sent and billed at the current prices Prices may be subject to change without notice Standard hardware items are available at local hardware stores If you find this product to have either a defective part or a missing part write the above address or for faster service phone Customer Service at 1 800 423 5502
Download Pdf Manuals
Related Search