Wegener Communications Unity Synchronous Data Option User's Manual
Contents
1. 64 0 6875 Kbps data rate range used with D command 0x0020 Ox FFE PID range used with P command Port port number 1 or 2 Sync data card status 3 UTY4000 007 REPORT COMMOND is r p The report will show if any sync data cards are available The line will read as follows Sync Data Card 1 or 2 INSTALLED The SYNC DATA report command is r sd The report will report the sync data card status in the following form FUNCTION CURRENT SETTING RS422 OUTPUT ENABLED DISABLED LVDS OUTPUT ENABLED DISABLED SYNC DATA RATE data rate PID PID STATUS 3 2 From Front panel Sync Data Card setup with local control disabled The sync data card setup cannot be accessed via the front panel with local control disabled The Network must authorize local control Sync Data Card setup with local control enabled The sync data card can be set via the front panel if local control is enabled by using the menu path HARDWARE SETUP CONTROL SYNC DATA Select the parameter you need to adjust by using the right left arrows and the lt SELECT gt key Use the up down arrows to select the desired setting Press the lt ENTER gt key to initialize the settings Sync Data Card status To confirm that the Sync Data card option is available via the front panel follow the menu path STATUS REPORTS PARAMETER STATUS Use the right left arrow keys to scroll to SYNC DATA To view how the sync data card is configured via the front panel fo2. PWB into selected position Take precautions against Electro static discharge to avoid damage to module Connect supplied 24 pin cable from J13 on the motherboard to J1 on the Sync Data Option card Set jumpers on option card J9 is the only jumper configurable by the user If the sync data card is installed as module 1 place J9 in the dotted position If the sync data card is installed as module 2 place J9 in the non dotted position Power up unit and verify that installed option is recognized under Status_Reports Parameter_Status menu Power down unit and re install cover 2 2 Customer Premises Wiring Outputs supplied on two RJ45 jacks Pins are numbered left to right 1 to 8 as seen from the open end with tab facing downward LVDS SIGNAL RS422 SIGNAL OUTPUT OUTPUT GND GND Table 1 RJ 45 Pin outs 3 CONTROL AND STATUS INDICATIONS Note Sync Data option card may be setup by your network and local control may be disabled If so only the status monitoring will be possible 3 1 From Terminal Sync data card setup with local control disabled The sync data card setup cannot be accessed via the terminal with local control disabled Local control will have to be authorized by the network Sync data card setup with local control enabled CSD cmd param port Cmd R Set RS422 output state L Set LVDS output state D Set data rate P Set PID Param E D Enable disable output ports used with R amp L commands
3. PRELIMINARY Installation Operation Guide Unity Synchronous Data Option Data drawings and other material contained herein are proprietary to Wegener Communications Inc and may not be reproduced or duplicated in any form without the prior permission of Wegener Communications Inc When ordering parts from Wegener Communications Inc be sure to include the equipment model number equipment serial number and a description of the part In all correspondence with Wegener Communications Inc regarding this publication please refer to UTY4000 007B First Edition February 1999 Revised June 2000 UU WEGENER COMMUNICATIONS TECHNOLOGY PARK JOHNS CREEK 11350 TECHNOLOGY CIRCLE ULUTH GEORGIA 30097 1502 770 814 4000 FAX 770 623 0698 1 INTRODUCTION The Unity Sync Data option card provides an IRD with a synchronous data channel output This data stream is carried in transport packets whose PID may be assigned in the Wegener UMX4025 at the uplink This data appears bit serial on either an RS422 or LVDS output port The RS422 and LVDS can be activated one at a time or simultaneously 2 INSTALLATION 2 1 Option Card Install 1 2 3 Power down UTY 4000 and remove top cover Do not lose special screws See Figure 1 page 5 Expansion module may be installed into either inboard Module 1 or outboard Module 2 position 3 Remove block out plate for selected position Save hardware UTY4000 007 Install
4. llow the menu path STATUS REPORTS SYNC DATA STATUS Use the right left arrow keys to scroll through the audio ports configuration UTY4000 007 4 Module 1 Module 2 gcrews from Rear EE blockout plate UNITY4000 MOTHER BOARD Mounting STANDOFFS Bracket ini from kit J12 J13 P S Pin 1 Pin 1 Front Figure 1 UTY4000 Sync Data Kit Installation UTY4000 007
Download Pdf Manuals
Related Search