Vision Fitness X6600HRT/DA User's Manual
Contents
1. X6600HRT DA dual action elliptical trainer To avoid possible damage to this Elliptical Trainer please follow these assembly steps in the correct order Before proceeding though find your new Elliptical Trainer s serial number located below the power switch and enter here Refer to this number when calling for service and also enter this serial number on your Warranty Card and in your own records Be sure to read your Owner s Guide before using your new Elliptical Trainer If any parts hardware or tools are missing please call 1 800 335 4348 Extension 12 NOTE lt is recommended that you apply grease to the threads of each bolt as you assemble your Elliptical Trainer to prevent loosening and noise Also during each assembly step ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt TOOLS amp PARTS INCLUDED Screwdriver 5 Allen Wrench PARTS BOX 8 Shaped Wrench Heart Rate Chest Strap Qty 1 Power Supply Qty 1 Arm Bracket Covers Qty 2 Logo Endcaps Qty 2 Stabilizers Qty 2 Stabilizer Covers Qty 2 Water Bottle and Holder Qty 1 Console Mast Cover Plate Qiy Assembly Guide Owner s Guide Warranty Card Parts Bags Tools HARDWARE INCLUDED MA 12 Screw Quantity A M8 x 12 Bolt Quantity 2 M8 Arc Washer Quantity 4 UE BA 6 M30 Teflon Washer Quantity 2 12 12 Screw Qua2. dlebar bracket Tighten the top bolt M8 on the arm bracket connection block using the 6 L shaped Allen wrench e Attach plastic arm bracket cover to the front of the arm bracket connection block This is a snap fit e Attach the plastic logo endcap to the side of the arm bracket connection block This is a snap fit Repeat the above steps on the left side e Attach water bottle bracket with the included screws CONSOLE e Remove the four screws from the back of the console Plug the wire connectors from inside the mast into the console The cable connectors are slotted so do not force the connection Mount the console to the mast using the four screws Do not pinch the cable 621 D East Lake Street e P O Box 280 e Lake Mills WI 53551 toll free 1 800 335 4348 e phone 1 920 648 4090 fax 1 920 648 3373 www visionfitness com 2001 Vision Fitness All Rights Reserved 3 01 Part Z66EP09 AG1803PRD A618 03PRD REVI
3. ntity 4 Q5 M20 Spring Washer Quantity 2 x TOM Screw Quantity M30 Washer M8 x 75 Bolt Quantity 2 Quantity 2 a e Install the left and right stabilizers with the four arcshaped washers M8 and four bolts M8 x 20 using the Blue 5 Allen wrench e Cover both stabilizers with the included rubber boots BLUE BAG e Slide the console mast cover onto the console mast e Unfold the console cable an attach it to the string located inside th console mast Guide the wire u through the mast while simultaneous sliding the console mast onto th frame bracket e Attach the console mast cover to t frame using four screws M4 x 12 e Bolt the mast to the frame with 1 two bols M8 x 75 using t 5 Blue handled Allen wrench Ma sure these are tight e Attach the console mast cover plate with the V head screw M3 x 10 e Slide a small spring washer M20 onto the lower pedal arm support followed by the right lower arm Attach with a white Teflon washer M30 a flat washer M30 and bolt M8 x 12 using Blue han dled 5 Allen wrench e Pivot the lower arm and insert the top end into the upper handlebar bracket e Tighten the bottom bolt M8 on the arm bracket connection block using the 6mm L shaped Allen wrench Repeat the above steps to attach the arms on the left side STEP 4 GREEN BAG e Slide right upper arm into right upper han
Download Pdf Manuals
Related Search