Ultra Start KE-5 User's Manual
Contents
1. of the vehicle Note any scratches or dents Check with the vehicle s owner before installation of LED light See if the owner has a preference for the location of the Valet Switch Have vehicle wiring information ready before starting installation Installation Tips Leave a window open to avoid locking the Key s in the vehicle Use seat covers and floor mats to protect the vehicle Avoid disconnecting the battery Unplug the dome light fuse to prevent battery drain Test all connections with a voltmeter or circuit safe test light Install the wire harness so that it is free of any moving parts Solder all connections Avoid using scotch lok and crimp connectors Pull the siren and optional hood pin wires through a factory rubber grommet into the engine compartment Do not use the steering boot Install the siren away from high heat sources and direct exposer to water Installation Manual Kla 5 Antenna Do Not Ground the antenna wire 250ma Output 12volts For Door Lock Module Onl 250ma Output 250ma Maximum Output Orange 250ma Maximum Output 250ma Maximum Output 250ma Maximum Output Yellow Red F Ground Input Black 5 10 Amp Output White E Q The 12volt output on the keyless entry connector is not to be used for anything other than suppling power for voltage inverter s and door lock modules such as the DL 3 and DL 7 250ma outputs are low current and are designed2. Default Setting Warning Chirp Off Passive Warning Chirp means that in passive mode 4 1 the system gives soft Warming chirp sounds during thirty second arming period after each temporary disarm 1Turn the ignition on Ignition on means normal driving position 2Within 10 seconds press and release the transmitter button Lock Trunk Unlock Trunk in succession CHIRP ON is confirmed with one horn chirp sound and one parking light flash CHIRP OFF is confirmed with two horn chirp sounds and two parking light flashes Setting 7 Reset to Factory Default To Reset all programmable features to factory default setting 1 Turn the ignition on Ignition on means normal driving position 2 Within 10 seconds press and release the transmitter button Trunk Lock Unlock Trunk in succession Reset to factory default is confirmed with three horn chirp sounds and three park Light flashes B05 Installation Manual POSITIVE TRUNK RELEASE Trunk Release Trunk Release Solenoid Switch NEGATIVE PARK LIGHTS Parking Parking Lights Light Switch Ie 87 White ory Ground nd 86 gs 30 Jal STARTER KILL To Starter Motor or Relay
3. E is confirmed with one horn chirp sound and one light flash ACTIVE MODE is confirmed with two horn chirp sounds and two light flashes Setting 2 Passive Lock Mode Factory Default Setting Active Lock Mode Passive Lock Mode means that all doors will lock automatically when the system arms in the passive mode Active Lock Mode means that doors will lock only with the lock button 1 Turn the ignition on Ignition on means normal driving position 2 Within 10 seconds press and release the transmitter buttons Unlock Trunk Unlock Trunk in succession PASSIVE LOCK MODE is confirmed with one horn chirp sound and one parking light flash ACTIVE LOCK MODE is confirmed with two horn chirp sounds and two parking Light flashes CAUTION If the automatic door lock feature is installed and the system is Programmed to passive lock mode the doors will lock automatically when the system arms Itis always advisable to remove the ignition key each time you exit the vehicle Setting 3 lgnition Auto Locks Factory Default Setting Locks Off Ignition Lock Mode means that all doors will lock automatically two 2 Seconds after the ignition key is turned on and will unlock automatically when the ignition key is turned off This assumes that the keyless entry option has been installed by your Dealer Sometimes referred to as Ignition Lock 1 Turn the ignition on Ignition on means normal driving position 2 Within 10 seconds press and release the transmitte
4. INSTALL GUIDE REMOTE STARTERS CAR ALARMS WWW_ _ULTRASTARTERS COM Technical Support Support ultrastarters com Note Some features may not be available on certain models FCC ID Notice This device complies with Part 15 of the FCC rules Operation is subject to the following conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the part responsible for compliance void the user s authority to operate this devise KEES Installation Manual Table Of Contents system Contents Pre Installation Installation Tips Main Wiring Diagram Quick Start Installation Wiring Description Transmitter Operation Transmitter Programming system Reset Quick View Programming Chart System Programming System Programming Relay WLAN S aarecmies gecaneroatectecateasen anstasias seamennstanteg seeoheantiantebaaecannartanicdse Page 8 System Contents Key Features Control Module Keyless Entry With Drivers Door Priority Four Button Remote Trunk Release Output Transmitter s Positive Park Light Output 10 Pin Harness Panic Mode Installation Guide Horn Honk Output Owners Manual Starter Disable Output Pre Installation BEFORE STARTING Discuss the optional features of the alarm with the owner of the vehicle Do a walk around
5. lec TRANSMITTER PROGRAMMING To add additional transmitters and delete existing transmitter code s from memory 1 Turn the ignition On Off On Off On Off On Off The park lights will flash twice 2 Press the Lock button on the transmitters to be programmed 3 The park lights will flash once each time a new transmitter is learned If this does not happen wait ten seconds and repeat steps 1 3 Note Each system can store a maximum of three transmitter codes in memory Transmitter Program on Power Up 1 Plug in the module Leave the ignition in the Off position 2 Press the lock button on each of the transmitters to be programmed 3 The park lights will flash once each time a new transmitter code is learned Note Previous transmitters that are not programmed at this time will deleted from memory SYSTEM RESET Reset To Factory Default Settings 1 Make sure ignition is in the OFF position 2 Turn the ignition key ON leaving key in the ON position 3 Press the transmitter buttons as follows Trunk Lock Unlock Trunk 4 The system will respond by flashing the park lights three times The system is now set to factory default settings QUICK VIEW PROGRAM MENU Entering The Program Menu 1 Make sure ignition is in the OFF position 2 Turn the ignition key ON leaving key in the ON position 3 Press the transmitter buttons in the appropriate sequence 4 After ten seconds the system will automatically e
6. r button Lock Trunk Lock Trunk in succession DRIVE LOCK MODE ON is confirmed with one horn chirp sound and one parking light flash DRIVE LOCK MODE OFF is confirmed with two horn chirp sounds and two parking light flashes Installation Manual KE 5 Setting 4 Long Door Lock Pulse Factory Default Setting Pulse Off Long Door Lock Pulse means that the system can accommodate the factory central locking systems of import vehicles having vacuum door lock actuators that require a three second lock pulse 1 Turn the ignition on Ignition on means normal driving position 2 Within 10 seconds press and release the transmitter buttons Lock Unlock Trunk Lock in succession LONG DOOR LOCK PULSE MODE is confirmed with one parking light flash SHORT DOOR LOCK PULSE MODE is confirmed with two parking light flashes Setting 5 Dual Unlock Pulse Factory Default Setting Dual Unlock Mode Off Dual Unlock Pulse means that the system can accommodate the factory central locking systems of import vehicles having dual unlock pulse to unlock the driver and passenger doors 1 Turn the ignition on Ignition on means normal driving position 2 Within 10 seconds press and release the transmitter buttons Unlock Trunk Unlock Lock in succession DUAL PULSE ON is confirmed with one horn chirp sound and one parking light flash DUAL PULSE OFF is confirmed with two horn chirp sounds and two parking light flashes Setting 6 Passive Warning Chirp Factory
7. to activate relays MESS Installation Manual STEP 1 The following wires MUST be connected for proper operation Red 124 Power 15amp Input Constant 12v power sourse Yellow Ignition 12volt Input Main ignition wre White Park Lights 15amp Output Connect to positive park lights Black Ground Input Connect to chassis ground Geen Lock Output 500ma Output Connect to door lock relay Blue Unlock Output 500ma Output Connect to door unlock relay Optional Connections Orange StDisable 500ma Output Connect to Starter Disable relay Brown Hom Output 500ma Output Connect to hom relay Gey Trunk Output 500ma Output Connect to Trunk Release relay Pink 2nd Unlock 500ma Output Connect when installing Driver s Door Priority STEP 2 CONNECT AND MOUNT THE MODULE Plug the Connectors into the Module Press the transmitter buttons to check for proper operation Once it is determined that everything is working correctly the module can be mounted Before plugging the module in make sure that Ignition Key is in the OFF position Mount the module by selecting a location under the dash that is secure Be certain that the module does not obstruct any serviceable areas The module must be free from moving parts such as brake clutch and gas pedals and the linkages that are attached to them Basic remote operations Unlock See Owners Manual for more transmitter operations Installation Manual
8. xit Program Mode To change a Programmable Feature press the transmitter buttons as follows Default settings are shown in bold lettering Passive Active Arming Lock Unlock Lock Unlock Passive Active Passive Active Locks Unlock Trunk Unlock Trunk Passive Active Ignition Aouto Door Locks Lock Trunk Lock Trunk ON OFF Door Lock Pulses Lock Unlock Trunk Lock Three Second 75 Second Double Pulse Unilock Trunk Unlock Lock Double Pulse Single Pulse Passive Warning Chirps Lock Trunk Unlock Trunk ON OFF Reset To Factory Defaults Trunk Lock Unlock Trunk Three flashes Three Flashes KE 5 Installation Manual Entering The Program Menu 1 Make sure ignition is in the OFF position 2 Turn the ignition key ON leaving key in the ON position 3 Press the transmitter button in the appropriate sequence 4 After ten seconds the system will automatically exit Program Mode Setting 1 Passive Active Mode Factory Default Setting Active Mode Passive mode means that the system will automatically arm thirty seconds after The ignition key is turned off and the last door of the vehicle is closed Sometimes referred to as Automatic Arming Active mode means that the system will not arm until you manually turn it on by pressing the lock button on your transmitter 1 Turn the ignition on Ignition on means normal driving position 2 Within 10 seconds press and release the transmitter buttons Lock Unlock Lock Unlock in succession PASSIVE MOD
Download Pdf Manuals
Related Search