Ultra Start 7 User's Manual
Contents
1. press the MODE button to exit 3 Dual Time Mode 1 In real time mode press the ST STP button to switch between the Real Time Mode and Digital Time Mode 2 Set the Dual Time in the same manner as the Real Time 4 Alarm Mode Page 4 ST STP 1 In real time mode press the MODE button to enter the Alarm Mode 2 Press the ST STP button to set the alarm ON OFF When the Bell Icon is displayed the alarm will sound at the preset time every day for 30 seconds To stop the alarm press any button If the alarm is ON the Bell Icon will be turned ON in all other modes How to Set Alarm Time 2 seconds ALM M ST STP ST STP 1 In real time mode press the MODE button to enter Alarm Mode 2 Hold the MODE button for 2 seconds the hour digits will begin to flash 3 While the hour digits are flashing press the ST STP button to increase the number Hold the ST STP button to increase the digits at a greater speed 4 Press RESET to enter the next field minute digits will begin to flash 5 To set the minute press the ST STP button 6 After you have set the minute press the MODE button to exit and save 5 Chronograph Mode Page 5 ST STP 1 In real time mode press the MODE button to enter the Chronograph Mode 2 Press the ST STP button to start chrono To stop the chrono press the ST STP button When the chrono is stopped press the RESET button so reset the time to zero W2. 007 Remote Wrist Watch Advanced Digital Wrist Watch with Alarm and Remote Starter Control Capabilities WATER RESIST eae 50M CARBON MONOXIDE MAY CAUSE SERIOUS INJURY EVEN DEATH It is the sole responsibility of the user to place the system in Service Mode when parking a vehicle equipped with a remote starterin an enclosed area ex garage partially enclosed area ex carport or when the vehicle is being serviced i a Warning a 1 Change from Mode to Mode Page 2 AFW Real Time Mode Alarm Mode Program Start Mode Timer Mode Chronograph Mode Press and release the MODE button to switch from Mode to Mode MODE BUTTON MODE SELECT Default Screen Real Time Mode Mode Button Once Alarm Mode Mode Button Twice Chronograph Mode Mode Button Three times Timer Mode Mode Button Four times Program Start Mode Mode Button Five times Returns to Real Time Mode 2 Real Time Mode How to Set Time and Date Page 3 2 seconds ST STP ST STP 1 Press and hold the MODE button to enter the Real Time Setting Mode 2 Press the ST STP button to select 12 or 24 hour format 3 Press the RESET button to go to the next field hour digits will begin to flash 4 While the hour digits are flashing press the ST STP button to increase the number Hold the ST STP button to change the number at a greater speed 5 Aftter you set the 12 24 hour format hour minute second year month and date
3. RANTY FCC Notice This device complies with Part 15 of the FCC rules Operation of this device is subject to the following conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the part responsible for compliance voids the users authority to operate this device
4. hen the chrono time is running the CHR icon will begin to flash in all other modes with the exception of Setting Modes 6 Timer Mode Page 6 ST STP 1 In real time mode press the MODE button 3 times to enter Timer Mode 2 Press the ST STP button to start the timer To stop press the ST STP again If the timer is stopped press RESET to reset the time to the present value When the timer is running the TMR Icon flashes in all other modes with the exception of setting modes 3 Press the MODE button to exit How to Set the Timer 2 seconds ST STP ST STP 1 In real time mode press the MODE button to enter the Timer Mode 2 Hold the MODE button for 2 seconds the hour digits will begin flashing 3 While the hour digits are flashing press the ST STP button to increase the number Hold the ST STP button to increase the number at a greater speed 4 Press RESET to go to the next field minute and seconds will begin flashing 5 After you have set the minute and seconds press the MODE button to save and exit 7 Program Start Mode Page 7 ST STP D Xa AMA Va ATEN 1 In real time mode press the MODE button 4 times to enter the Program Start mode 2 Press the ST STP button to change the ON OFF function of the Program Start When the PRO icon is ON the engine will start and run at the preset time The remote will beep three times to confirm starting of the engine The remote start will only activa
5. te when the system is armed and within RF operating range 3 Press the MODE button to exit How to Set the Engine Start 2 seconds Pro 16m De BOR ro ATEN ay Y ki M TMR ua la ATEI j TMR IE Cadm Va ATC P h io ip yy IMR ST STP ST STP 1 Press the MODE button to enter the Program Start Mode 2 Hold the MODE button for 2 seconds the hour digits will start flashing 3 While the digits are flashing press the ST STP button to increase the number Hold down the ST STP button to change the number at a greater speed 4 To set the minute press the RESET button 5 After you set the hours and minutes press the MODE button to exit and save Remote Control Mode For Vehicles Page 8 HD Button 1 MD Button 2 Arm Lock Press and release Disarm Unlock Press and release Panic Mode Press and hold for Trunk Release Press and hold for 2 seconds 2 seconds Wl Light Button Remote Start Press and release Remote Stop Press and hold for 2 seconds Program Start On Low Battery sq MODE Button 5 ST STP Button Alarm On Light Button p Button 1 Button 2 Battery Replacement Change the battery when the Low battery icon is displayed on the LCD screen Replace with Lithium CR2032 Battery To avoid possible water damage have the battery changed professionally Caution DO NOT DISASSEMBLE THIS WATCH FOR ANY OTHER REASON THEN TO REPLACE THE BATTERY REMOVING ANY OTHER COMPONENT S WILL VOID THE WAR
Download Pdf Manuals
Related Search