U-Line COMBO ADA151M User's Manual
Contents
1. i15 Service l6 Normal Operating Sounds we 16 Troubleshooting Guides 16 Before Calling for Service nitidi 16 ESCRITA Required ep l6 Replacement Parts nt o e ce ER Ua eret tari ERE i l6 12 U Line Corporation Limited Warranty 17 U Line Use and Care Table of Contents U Line Use and Care Guide 3 Safety Precautions IMPORTANT PLEASE READ all instructions before installing operating or servicing the appliance Proper installation procedures must be followed when completing an installation or relocation of a unit Consult the installation guide before any installation begins U Line contact information appears on the rear cover of this guide This unit requires connection to a dedicated 15 Amp grounded three prong polarized receptacle installed by a qualified electrician compliant with applicable electrical codes Safety Alert Definitions Throughout this guide are safety items labeled with a Danger Warning or Caution based on the risk type AXDANGER Danger means that failure to follow this safety statement will result in severe personal injury or death NWARNING Warning means that failure to follow this safety statement could result in serious personal inju2. The unit must be located on a level surface for proper door and ice maker if equipped operation Use a level to check the levelness of the unit from front to back and from side to side Place the level along top edge and side edge as shown 1 Removing and Installing Interior Shelves For models equipped with glass shelves having shelf supports remove the shelves as follows Open door completely 2 Grasp the shelf edge in the center and slide the shelf from the unit Insert the shelves as follows Reposition the shelf as required ensure the raised white edge strip is toward the rear of the unit and graphics if applied are on the underside of the shelves 8 U Line Combo Models and Ice Makers Maintenance Removing and Installing Grille NWARNING Disconnect electric power to the unit before removing the grille NWARNING DO NOT touch the condenser fins 4 The condenser fins are SHARP and can be easily damaged Removing the grille 1 Disconnect power to the unit Remove control knob 6 if equipped M Loosen the two screws 1 Some models may have only one screw in the center te 4 Remove grille 2 and grille cap if equipped 3 from unit Installing the grille 1 For 15 and 29 models make sure grille cap 3 is behind grille in slots 2 provided in grille before attaching grille to unit 2 For 75 models place the
3. its outlet DANGER RISK OF CHILD ENTRAPEMENT Before you throw away your old refrigerator or freezer take off the doors and leave shelves in place so children may not easily climb inside 3 Remove the cabinet door U Line Combo Models and Ice MakersCleaning 15 Service Before Calling for Service If you think your U Line product is malfunctioning read the OPERATION section of this guide to understand clearly the function of the control If the problem persists read the NORMAL OPERATING SOUNDS and TROUBLESHOOTING GUIDE section of this guide to help you quickly identify common problems and possible causes and remedies Most often this will resolve the problem without the need to call for service If Service is Required If you do not understand a troubleshooting remedy or your product needs service contact U Line Corporation directly Contact information appears on the rear cover of this guide When you call you will need your product Model and Serial Numbers This information can be recorded inside the front cover of this guide It also appears on the Model and Serial number plate located on the upper right or rear wall of the i
4. These instruments can puncture the inner lining or damage the cooling unit DO NOT use any type of heater to defrost Using a heater to speed up defrosting can cause personal injury and damage to the inner lining IMPORTANT Do not lift unit by door handle Never install or operate the unit behind closed doors Be sure front grille is free of obstruction Obstructing free airflow can cause the unit to malfunction and will void the warranty Failure to clean the condenser every six months can cause the unit to malfunction This could void the warranty Allow unit temperature to stabilize for 24 hours before use Do not Block any internal Fans Use only genuine U Line replacement parts Imitation parts can damage the unit affect its operation or performance and may void the warranty w 4 Product Features 6 LINE Ice Makers Feature High ice production and storage 151 BI2115 and BI98 models produce up to 25 pounds of ice per day and store 25 pounds BI95 and SP18 models produce up to 23 pounds of ice per day and store 12 pounds Combo Models produce up to 18 pounds of ice per day and store 13 pounds and provide both ice production and refrigeration in one COI 175 has 4 2 cubic feet and CO29 has 2 1 cubic feet refrigeration storage No drain required Easy and inexpensive to install Only requires a 1 4 outside diameter water line Conserves on water Uses under 3 gallons of water to produc
5. DANGER ELECTROCUTION HAZARD Never attempt to repair or perform maintenance on the unit until disconnecting the main electrical power Troubleshooting What to check when problems occur Problem Possible Cause and Remedy Interior Light Does Not Illuminate The light bulb may be defective See MAINTENACE Light Remains on When Door is Closed Adjust light actuator bracket ob bottom of door Unit Develops Frost on Internal Surfaces Unit is a manual defrost model that will require occasional defrosting When there is build up of 1 4 or more manually defrost the unit Ensure the door is closing and sealing properly High ambient temperature and excessive humidity can also produce frost Unit Develops Condensation The unit is exposed to excessive humidity moisture will dissipate as humidity levels increase Combo Models on External surfaces Product is Adjust the temperature to a warmer set point See Freezing in OPERATION Product is Not Cold Enough in Combo models Air temperature does not indicate product temperature See OPERATION Checking Product Temperature Adjust the temperate to a cooler set point See OPERATION Ensure unit is not located in excessive ambient temperatures or in direct sunlight Ensure the door is closing and sealing properly Ensure the interior light has not remained on too long Ensure nothing is blocking the front grille found at
6. built in undercounter ice making refrigeration and wine storage appli ances the U Line Corporation is committed to luxury under the counter U Line is known and respected for unwavering dedication to product innovation quality and selection A bold and broad line of models is the prod uct of visionaries in the pursuit of distinctive living environments in the kitchen and spaces beyond In 1962 Henry Uihlein founded U Line Corporation as an outgrowth of Ben Hur Freezer Company and was the first to develop and patent an automatic stand alone undercounter residential ice maker His foresight and determination to develop new ideas and to succeed when there were no clear guidelines or solutions are evi dent today The Milwaukee Wisconsin based family operated business provides continuity and vision from which innovations continue to be born Going forward U Line will continue offering best in class products that build on the company s numerous pat ents and world firsts to guide the undercounter industry in realizing its unlimited potential
7. compartment because they will freeze To turn off ice production Raise the bin arm into an upright and locked position The unit will preserve temperature for ice storage IMPORTANT If not intending to use the ice maker turn the water supply valve off it is important to raise the bin arm of the ice maker Figure 1 Failure to raise the bin arm may result in damage to the water valve Certain sounds are normal during the unit s operation You may hear the compressor or fan motor the water valve or ice dropping into the ice bucket NWARNING NEVER use an ice pick knife or other sharp instrument to separate cubes Shake the ice bucket instead During periods of limited use or high ambient temperatures it is common for cubes to fuse together Gently shake the bucket to break apart cubes If not using the ice maker regularly empty the ice bucket periodically to ensure fresh cubes It is normal for cubes to appear cloudy The cause is air trapped in the water because of fast freezing It is not caused by the health taste or chemical make up of the water It is the same air that is in every glass of water you drink Remove the ice bucket for emptying and cleaning To remove the ice bucket raise the bin arm and remove the bucket from the ice compartment Use the ice bucket for ice storage only Ice Maker Adjustment Ice Cube Thickness Adjustment Interval As Required On ice maker equipped models adjust the c
8. hook hinge located on the rear bottom side of the grille 2 onto the front lip of the unit base Swing the grille up into position 3 Align cabinet and grill holes and secure but do not overtighten grille screws 1 4 Install control knob 6 if equipped 5 Reconnect power to the unit 29 Models Ice Maker Models s 2 1 MANN LRH Removing and Installing Door Shelves 1 For models equpped with door shelves To remove the door shelf Grasp shelf in center and lift until the shelf notches 1 clear the pins 2 2 Carefully pull the shelf away from the door To install the door shelf 1 Holding the shelf in the center center the shelf in the door at the desired location slightly above the pins 2 2 Lower the shelf onto the pins 2 U Line Combo Models and Ice Makers Maintenance 8 Standard Doors Door Alignment and Adjustment Align and adjust the door if it is not level or is not sealing properly If the door is not sealed the unit may not cool properly or excessive frost may form in the interior IMPORTANT Properly aligned the door s gasket should be firmly in contact with the cabinet all the way around the door no gaps Carefully examine the door s gaske
9. incurred in connection with the replacement of any defective part During years two through five of the warranty period for the sealed system U Line shall 1 at U line s option repair or replace any part of the sealed system and 2 for all Marine RV and Domestic U Line products sold and serviced in the United States including Alaska and Hawaii and Canada U Line shall be responsible for the labor costs incurred in connection with the replacement of any defective part of the sealed system All other charges including transportation charges for replacements under this warranty and labor costs not specifically covered by this warranty shall be the responsibility of the purchaser This warranty extends only to the original purchaser of the U Line product The registration Card included with the product should be promptly completed by you and mailed back to U Line or you can register on line at www u lineservice com 3 The following conditions are excluded from this limited warranty damage caused by outdoor use use of cleaners other than the recommended stainless steel cleaners and U Line Clear Ice Maker cleaner installation charges damages caused by disasters or acts of God such as fire floods wind and lightning damages incurred or resulting from shipping improper installation unauthorized modification or misuse abuse of the product customer education calls food loss and spoilage door and water level adjustments except durin
10. loading refrigerator or freezer with product IMPORTANT On ice maker equipped units it is possible that dirt or scale will dislodge in the water line Always throw away all ice cubes made during the first two to three hours of operation TE ra To turn the unit on or off Press the rocker switch located below the temperature control dial in the center of the grille 2 inside the door on the front panel or behind the grille Control Dial Combo Models provide two temperature zones within the cabinet to satisfy the specific storage requirements The control dial sets a single continuous temperature This set point temperature is a base setting used by the controller to maintain the temperature zone in the unit The factory default MID setting number 3 or 4 set point for Beverage Center and Refrigerator models is 38 F The factory default set point Wine U Line Product Operation 5 Adjusting AirTemperature Combo Models IMPORTANT Adjust the set point temperature in single increments and wait 24 hours for the temperature to stabilize before rechecking Factory recommended set point is MID setting on dial control To adjust the set point temperature Adjust the temperature by turning the numbered dial 1 in small increments Adjusting Ice Harvest BI Models 1 Remove the front grille see MAINTENANCE 2 Turn the adjusting screw 3 using a fla
11. the cabinet three screws 2 2 Remove the two door closer inserts 4 from the existing bottom hinge 3 Install door closer inserts as shown on the new bottom hinge 4 Remove existing bottom hinge Remove the existing bottom hinge three screws 2 Reinstall hinge to top opposite Install the hinge just removed from the bottom to the TOP opposite side of the cabinet three screws 2 Reinstall Hole Plugs Install plastic screw plugs three each top and bottom 3 into holes where hinge hardware was removed Prepare door for reinstallation Remove plastic hole plug from top of door handle and reinstall on opposite side 2 With bottom of door facing up remove pivot plate 5 two screws 3 Flip over and install pivot plate on opposite side of door Ensure notch in plate faces center Install Door Hold door upright and tilted forward Lift door on to bottom hinge closer inserts Tilt door forward into position Hold door to keep it from falling gt Ww oM Reinstall hinge screw pin 1 into top hinge using a Phillips screwdriver Align and adjust the door Align and adjust the door see DOOR ALIGNMENT AND ADJUSTMENT above U Line Self Closing Door Alignment and Reversal 13 10 Cleaning Exterior Cleaning Vinyl Clad Black or White Models Clean surfaces with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Us
12. up promptly can penetrate the surface of the stainless steel and complete removal of the rust may not be possible Interior Cleaning Disconnect power to the unit Clean the interior and all removed components using a mild nonabrasive detergent and warm water solution applied with a soft sponge or non abrasive cloth Rinse the interior using a soft sponge and clean water Do notuse any solvent based or abrasive cleaners These types of cleaners may transfer taste to the interior products and damage or discolor the interior Defrosting Manual Defrost Models Unit is a manual defrost model and will require occasional defrosting When there is build up of 1 4 or more of frost manually defrost the unit Defrost every two months minimum Ensure the door is closing and sealing properly High ambient temperature and excessive humidity can also produce frost NCAUTION DO NOT use an ice pick or other sharp instrument to help speed up defrosting These instruments can puncture the inner lining or damage the cooling unit DO NOT use any type of heater to defrost Using a heater to speed up defrosting can cause personal injury and damage to the inner lining To defrost 1 Disconnect power to the unit 2 For combo models remove all products from the interior 3 Remove ice bucket and discard ice 4 Place towel or other absorbent materialon bottom of ice bin For combo models also place in bottom of unit 5
13. Fill the ice bucket half full with warm not hot water This will help the unit defrost faster 6 Place the ice bucket back into the unit on top of the towel or other absorbent material 7 Prop the door in an open position 2 in 5 cm minimum 8 After about hour remove the ice bin and discard water 9 Allow the frost to melt naturally I0 After the frost melts completely clean the interior and all removed components See INTERIOR CLEANING IMPORTANT DO NOT clean ice bucket using a dishwasher The bucket is not dishwasher safe and will be damaged 11 When the interior is dry reconnect power and turn unit on NOTE To safeguard against contaminates in ice discard first three batches of ice after defrosting 14 U Line Combo Models and Ice Makers Cleaning Condensor Cleaning Interval Every Six Months To maintain operational efficiency keep the front grille free of dust and lint and clean the condenser every three months Depending on environmental conditions more or less frequent cleaning may be necessary NWARNING Disconnect electric power to the unit before cleaning the condenser NWARNING DO NOT touch the condenser fins The condenser fins are SHARP and can be easily damaged IMPORTANT DO NOT use any type of cleaner on the condenser unit Remove the grill See MAINTENANCE 2 Clean the condenser coil 4 using a using a soft brush with a combing action or vacuum cleaner Do not t
14. USE AND CARE GUIDE u LiNeE COMBO MODELS amp MANUAL DEFROST ICE MAKERS COI175 BI95 BI98 Introduction LINE Congratulations on your purchase of a U Line refrigeration product Building on 45 years U Line has captivated those with an appreciation for the finer things with exceptional design inspired innovations and attention to even the smallest details U Line is synonymous with premium built in under counter ice making refrigeration and wine storage appliances the U Line Corporation is committed to luxury under the counter U Line is known and respected for unwavering dedication to product innovation quality and selection A bold and broad line of models is the product of visionaries in the pursuit of distinctive living environments in the kitchen and spaces beyond In 1962 Henry Uihlein founded U Line Corporation as an outgrowth of Ben Hur Freezer Company and was the first to develop and patent an automatic stand alone under counter residential ice maker His foresight and determination to develop new ideas and to succeed when there were no clear guidelines or solutions are evident today The Milwaukee Wisconsin based family operated business provides continuity and vision from which innovations continue to be born Going forward U Line will continue offering best in class products that build on the company s numerous patents and world firsts to guide the under counter industry in realizing its unlim
15. al or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state U Line Warranty USE AND CARE GUIDE PRODUCT INFORMATION Installation Guides with complete installation information Custom Wood Panel Size Specifications amp Installation Instructions CAD Drawings Use and Care Guides Specifications amp Feature Benefits are available for viewing and download on line at www u line com specs SERVICE INFORMATION If you have a problem with this appliance your use and care guide has troubleshooting information to help you quickly identify common problems and provide information on possible cause and remedy Answers to Customers Frequently Asked Questions are available at www u line com customer faq cfm You may contact U Line directly GENERAL INQUIRIES SERVICE ASSISTANCE U Line Corporation Phone 800 779 2547 P O Box 245040 FAX 414 354 5696 Milwaukee Wisconsin 53224 9540 U S A Email onlineservice u line com Phone 414 354 0300 www u lineservice com FAX 414 354 7905 Email sales u line com PARTS ASSISTANCE www u line com E mail onlineparts u line com ABOUT U LINE Building on 45 years U Line has captivated those with an appreciation for the finer things with exceptional design inspired innovations and attention to even the smallest details U Line is synonymous with premium
16. ature sees tenente tnnt trennen tentent senten tentent senten teen ten sten tenent eenenn 6 Pxjutunraedariaglj e 6 Checking Product Temperature 6 6 Ice Maker m Ice Maker Adjustment f Ice Maker Operation mem 7 7 MaintemanCe 8 Dee bia ac c M 8 Removing and Installing Interior Shelves eene tentent tette tenente 8 Removing and Installing Door Shelves 9 Removing and Installing Grille eerte eia aa nia ELE EENE 9 8 Standard Doors 10 Door Alignment and Adjustment eerte tnnt tente tentent tnnt teens tnntentennenne 10 Door REVersability Dt 10 Reversing the door ee TE 10 EET Xena e n 12 Door Alignment and Adjustment essent tnnt tentent tentent tentent te 12 Bid ours 12 Reversing the door we 12 10 Cleaning we 14 Exterior Cleaning 14 Interior Cleaning H 14 De frosting scosse OE 14 Mm 15 Storage Vacation and Moving sese tente 15 Product Disposal
17. e 22 pounds of ice or 2 1 4 gallons for 18 pounds Built in or freestanding Provides custom look when built in with no additional venting clearance needed on sides top or rear Do not obstruct the grille Vinyl clad cabinet Textured rich appearance More resistant to scratching peeling and flaking Door will accept a 1 4 panel Ability to match surrounding d cor and cabinets Black and white models only Integrated handle Does not add depth to the cabinet when built in Black and white models only Field reversible doors Flexible installation options All models with black and white doors are field reversible Stainless steel models must be order right or left hand hinged Flat recessed grille Blends with the other models and integrates with surrounding cabinetry Defrost Type Manual Defrost For indoor use only ADAI5IM Model Features Factory installed door locks Provides security and safety Stainless steel models Offers a bold stainless steel habdle stainless steel wrap door Stainless steel models must be ordered right or left hand hinged Combo Models Feature Mechanical Temperature Control Provides ability to set the temperature Adjustable tempered glass shelves Sleek streamlined interior Allows flexible shelf locations to meet varying food and beverage storage needs Three in 75 Two in 29 In door storage shelves Two adjustable on 75 model and 3 on 29 model Easiest access storage area r
18. e a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting Clean any glass surfaces with a non chlorine glass cleaner Stainless Models Stainless door panels handles and frames can discolor when exposed to chlorine gas pool chemicals saltwater or cleaners with bleach Keep your stainless unit looking new by cleaning with a good quality all in one stainless steel cleaner polish monthly For best results use Claire Stainless Steel Polish and Cleaner which can be purchased from U Line Corporation Part Number 173348 Comparable products are acceptable Frequent cleaning will remove surface contamination that could lead to rust Some installations may require cleaning weekly Do not clean with steel wool pads Do not use stainless steel cleaners polishes on any glass surfaces Clean any glass surfaces with a non chlorine glass cleaner Do notuse cleaners not specifically intended for stainless steel on stainless surfaces this includes glass tile and counter cleaners If any surface discoloring or rusting appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser amp and a nonabrasive cloth Always clean towards the grain Always finish with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems Using abrasive pads such as Scotchbrite will cause the graining in the stainless to become blurred e Rust not cleaned
19. es splashing of pool water or directing a spray from a hose or similar device into and around the unit 5 If a product defect is discovered during the applicable warranty period you must promptly notify either U Line at P O Box 245040 Milwaukee Wisconsin 53224 or at 800 779 2547 or the dealer from whom you purchased the product In no event shall such notification be received later than 30 days after the expiration of the applicable warranty period U line may require that defective parts be returned at your expense to U Line s factory in Milwaukee Wisconsin for inspection Any action by you for breach of warranty must be commenced within one year after the applicable warranty period 6 THIS LIMITED WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ALL OF WHICH ARE DISCLAIMED U Line s sole liability and your exclusive remedy under this warranty is set forth in the paragraphs above U Line shall have no liability whatsoever for any incidental consequential or special damages arising from the sale use or installation of the product or from any other cause whatsoever whether based on warranty express or implied or otherwise based on contract tort or any other theory of liability 7 Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incident
20. g the first 30 days from the date of installation defrosting the product adjusting the controls door reversal and cleaning the condenser 4 U Lines Outdoor Limited Warranty set forth in this Paragraph 4 shall apply to U Line models deemed suitable for outdoor use by Underwriters Laboratory UL as noted in the U Line Product Catalog U Line s website and or on the serial tag located inside the product Exposure to temperatures below freezing may cause damage to the product Damage resulting to the product and or the surroundings caused by this exposure is not covered under this warranty Such models shall continue to be covered by the warranty terms set forth in Paragraphs 1 and 2 above to the extent such models A Are subjected to temperatures between 50 and 100 degrees Fahrenheit Although these products will function in ambient temperatures below 50 degrees and above 100 degrees Fahrenheit performance may decline Performance degradation due to operating above or below the designated ambient temperature range is not a manufacturing defect and any issues resulting from exposure to higher temperatures such as spoiled food or low ice production are not covered under this warranty policy and or B Come into contact with rain by virtue of outdoor use Exposure to other sources of water shall also cause this warranty to be void including flooding of the area in proximity of the unit greater than 1 8 deep in water hurrican
21. ight where you need it Adjustable to allow flexible storage options CO1175 and BI2115 Model Feature Adjustable leveling legs Achieve a more precise under counter fit Durable strong legs will not bend when unit is installed Stainless steel model Offers a bold stainless steel handle stainless steel wrap door BI2115 has full wrap CO1175 has black cap on top and bottom of the door Stainless steel models must be order right or left hand hinged BI2115 Model Features Optional 3 4 full overlay door panel kit Provides a fully integrated appearance with surrounding d cor while maintaining zero door clearance Easy to install Black and white models only Must order kit number U OL21 15 Self closing door Engages when the door is open 8 10 Ensures a positive door seal and prevents door bounceback Contemporary grille design Integrates seamlessly with surrounding cabinetry 4 U Line Combo Model and Ice MakerProduct Features Product Operation Air Flow IMPORTANT The unit requires proper air flow to perform at its highest efficiency Do not block the front grille or internal fans at any time or the unit will not perform as expected Do not install the unit behind a door Initial Startup All U Line controls are preset at the factory Initial startup requires no adjustments IMPORTANT U Line recommends allowing the unit to run overnight before
22. ited potential Read and save this Use and Care Guide IMPORTANT READ all instructions in this guide completely before using the appliance for the first time For future reference keep this guide in a safe accessible location If you need additional information or assistance please contact U Line Corporation direct Contact information appears on the back cover of this guide Before Calling Service If you think your U Line product is malfunctioning read the OPERATION section of this guide to understand clearly the function of the control If the problem persists read the TROUBLESHOOTING GUIDE section of this guide to help you quickly identify common problems and provide information on possible causes and remedies Please Record Your Model Information You will need your product model and serial number when you request additional information or services You can find this information on the serial plate located on the upper right or back wall in the interior of your product This information also appears on the warranty registration card FoR PRODUCT ASSISTANCE CALL 1 800 779 2547 LI i LI N E www u line com MILWAUKEE WI U S A HIGH SIDE DESIGN PRESSURE 300 PSI 00 REFRIGERAT 1 LOW SIDE DESIGN PRESSURE 140 PSI US 674R 2 Model Modele Serial Serie g HOUSEHOLD REFRIGERATOR AND M A Please record the model number 1 serial number 2 date of purchase and dealer contact infor
23. leum jelly to the mating surfaces of the closers Be sure that pins on closers align with holes in the door and bottom cabinet hinge plates Mount door and install top hinge pivot pin Door Reversability Location of the unit may make it desirable to mount the door on the opposite side of the cabinet Models with black and white doors are field reversible Stainless steel models must be ordered right or left hand hinged Reversing the door The Hinge hardware will be removed and reinstalled on the opposite side of the cabinet The top hinge hardware will be reinstalled on the bottom of the opposite side of the cabinet The bottom hinge hardware will be reinstalled on the top of the opposite side of the cabinet 12 U Line Self Closing Door Alignment and Reversal To reverse the door Remove door 1 Hold door to keep it from falling 2 Remove hinge screw pin 1 from top hinge using a Phillips screwdriver 3 Remove door by tilting forward and lifting door off bottom hinge closer inserts 4 Reinstall hinge screw pin 1 into top hinge using a Phillips screwdriver Remove hole plugs Remove plastic screw plugs three each top and bottom 3 from new hinge location Save for reinstallation later Remove existing top hinge Remove existing top hinge three screws 2 Reinstall hinge to bottom opposite 1 Install the hinge just removed from the top to the BOTTOM opposite side of
24. mation for your U Line product below Model Number Serial Number Purchase Date Dealer Name Dealer Address Dealer Telephone Introduction to U Line Table of Contents U LineCombo Models and Ice Makers i Introduction re RR EIE D nee i Read and save this Use Care Guide cccccsssssssscsssssessssssesssesssscsssesessscscsesescscsesesessseesssesessseeseseacsesesseees i Please Record Your Model Information ccccccsssssssssscsesssssscsesessssesescsesessesesesesessscsesesessescacassesssceesesesesesseees i Table of COhEeltsco necne nae ee EE A 3 Safety PRECAUTIONS pc 3 Safety Alert Definitions 23 General Precautions 3 4 Product Features 4 Ice Makers Featlite 2 oct eerte io tei dese EI D rU dien RIO te en ERROR IMG EUH 4 ADAISIM Model Features ios ES ERE ERN 4 Combo G Models Features co sscscscssascccssssscsssacsesessesecascscssseneasasbhevensscocedencus PELIS eb Do ERE 4 COI175 and BI21 15 Model Feature ten ER ean EE ERN 4 BI2115 Model Features 4 5 Product Operation 5 Air Flow inital Startup saa O 5 SPI 5 Adjusting AirTemper
25. nterior of your product Replacement Parts When you need replacement parts always request genuine U Line replacements U Line designs and engineers products using components that work efficiently and provide superior service life and performance The use of aftermarket parts or components may affect the safety operation performance or durability of your product and may also void its warranty Normal Operating Sounds All models incorporate rigid foam insulated cabinets to provide high thermal efficiency and maximum sound reduction for its internal working components Despite this technology your model may make sounds that are unfamiliar Normal operating sounds may be more noticeable because of the units environment Hard surfaces such as cabinets wood vinyl or tiled floors and paneled walls have a tendency to reflect normal appliance operating noises Listed below are common refrigeration components with brief description of the normal operating sounds they make NOTE Your product may not contain all the components listed Compressor The compressor makes a hum or pulsing sound that may be heard when it operates Evaporator Refrigerant flowing through an evaporator may sound like boiling liquid Condenser Fan Air moving through a condenser may be heard Automatic Defrost Drain Pan Water may be heard dripping or running into the drain pan when the unit is in the defrost cycle Troubleshooting Guide A
26. ol properly or excessive frost may form in the interior IMPORTANT Properly aligned the door s gasket should be firmly in contact with the cabinet all the way around the door no gaps Carefully examine the door s gasket to ensure that it is firmly in contact with the cabinet Also make sure the door gasket is not pinched on the hinge side of the door The door will not be flush with the top of the cabinet The top edge of the door will be 1 8 in 3 175 mm below the cabinet top 1 8 3 175 mm To align and adjust the door 1 Compare the top edge of the door opposite the hinges to the top edge of the cabinet and note the type up or down of adjustment needed S 1 ee 2 6 3 2 Remove the top hinge pivot pin with a Phillips screwdriver and lift door off bottom hinge pin Be careful not to lose the door closer insert sets o Turn the door upside down and inspect the hinge plate mounting holes The plate has slotted mounting holes Loosen but do not remove the two hinge plate screws 1 A If door edge opposite the hinges needs to move up move plate toward outside of door 2 If door edge needs to move down move plate toward inside of door 3 Repeat until top edge of door is parallel with top of cabinet and tighten screws 1 securely 5 After adjustment is complete remove the door closers from the bottom hinge clean thoroughly and apply petro
27. ouch the condenser coil 3 Install the grill See MAINTENANCE 29 Models Typical Model Shown 75 Models 4 Typical Model Shown Icemaker Models Typical Model Shown RT 2 1 Storage Vacation and Moving If not using the unit for an extended period or otherwise stored follow these steps completely NWARNING Electrical Shock Hazard Disconnect power before servicing Before operating replace all panels Failure to do so may result in death or electrical shock IMPORTANT If the ambient temperature is expected to drop below 50 F turn off and unplug unit and drain all water from the unit to prevent freezing damage not covered by the warranty 1 Remove all consumable contents from the unit 2 Disconnect the power cord from its outlet and leave it disconnected until the unit is returned to service 3 Clean and dry the interior of the cabinet 4 During periods of nonuse the cabinet must remain open to prevent formation of mold and mildew Open door a minimum of 2 in 5 cm to provide the necessary ventilation Product Disposal If the unit is being removed from service for disposal check and obey all Federal State and or Local regulations regarding the disposal and recycling of refrigeration appliances and follow these steps completely 1 Remove all consumable contents from the unit 2 Disconnect power to the unit and unplug the power cord from
28. rom door Be sure to only remove the two screws holding the actuator to the door Reinstall che actuator 4 on the opposite end of the door where the nameplate was removed 8 Install new nameplate where the actuator assembly was removed 9 Install screws into holes on opposite side where the hinge was removed Replace nuts if used Prepare door for reinstallation For black or white doors Remove plastic hole plug from top of door handle and reinstall on opposite side 2 Remove plastic hinge bushing on bottom of door and reinstall on opposite side Clean out bushing hole in door bottom with a screwdriver if necessary Install top hinge and door l Reorient the pivot screw so it protrudes the opposite direction from the hinge Remove the pivot screw from the hinge Turn the plate over and reinstall the screw 2 Hold door to keep it from falling 3 Lift the door on to the bottom hinge 4 Align flat edge of the hinge with the outer edge of the unit 5 Install three or four screws depending on model Align and adjust the door l Align and adjust the door see DOOR ALIGNMENT AND ADJUSTMENT above Install grille Install the grille see MAINTENANCE section of this guide U Line Standrd Door Alignment and Reversal lI 9 Self Closing Doors Door Alignment and Adjustment Align and adjust the door if it is not level or is not sealing properly If the door is not sealed the unit may not co
29. rom hinge holes on the opposite side Reinstall into holes where the hinge was removed Ensure not to scratch cabinet Remove bottom hinge Remove bottom hinge from cabinet Some models will have a gusset with two screws Other models will have a plate with three screws 2 Remove corresponding screws on opposite side of cabinet On 10 U Line Standard Door Alignment and Reversal Install bottom hinge If you have a plate hinge reorient the pivot screw so it protrudes the opposite direction form the hinge Remove the pivot screw from the hinge Turn the plate over and reinstall the screw 2 Align hinge outer edge with cabinet For models with a plate hinge the flat edge of the hinge alignes with the outer edge of the cabinet Install two or three screws depending on model Replace nuts if used gt Prepare door for reinstallation For stainless steel models with glass doors 3 Stainless glass doors are flipped upside down to be reversed 4 Lay the door on it s side Remove the plastic hole plug 1 and install in the corner opposite of where it was removed 5 Remove the plastic hinge bushing 2 and install in the corner opposite of where it was removed 6 Remove the U Line nameplate 3 from door This will reveal mounting holes for the door actuator bracket 7 Remove door actuator 4 f
30. ry property or equipment damage NCAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or equipment damage U Line Safety Precautions General Precautions Use this appliance for its intended purpose only and follow these general precautions with those listed throughout this guide DANGER RISK OF CHILD ENTRAPMENT Before you throw away your old refrigerator or freezer take off the doors and leave shelves in place so children may not easily climb inside NWARNING SHOCK HAZARD Electrical Grounding Required Never attempt to repair or perform maintenance on the unit until the electricity has been disconnected Never remove the round grounding prong from the plug and never use a two prong grounding adaptor Altering cutting of power cord removal of power cord removal of power plug or direct wiring can cause serious injury fire and or loss of property and or life and will void the warranty Never use an extension cord to connect power to the unit Always keep your working area dry NWARNING Install provided Anti Tip kit on all Wine Captain Models and Beverage Centers Serious personal injury could occur NCAUTION Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges If your model requires defrosting DO NOT use an ice pick or other sharp instrument to help speed up defrosting
31. t tip screwdriver in a small increment clockwise for a COLDER setting slower ice production or counterclockwise for a WARMER setting faster ice production 3 Replace the front grille two screws Checking Product Temperature To check the actual product temperature in the unit 1 Partially fill a plastic nonbreakable bottle with water Insert an accurate thermometer Tighten the bottle cap securely 2 3 4 Place the bottle in the desired area for 24 hours 5 Avoid opening the unit during the testing period 6 After 24 hours check the temperature of the water If required adjust the temperature control in a small increment See ADJUSTING TEMPERATURE Causes which affect the internal temperatures of the cabinet include Temperature setting Ambient temperature where installed Installation in direct sunlight or near a heat source The number of door openings and the time the door is open The time the internal light is illuminated This mainly affects product on the top rack or shelf The front grille or condenser are obstructed U Line Product Operation 6 Ice Maker Ice Maker Operation When the ice bucket is full the ice making mechanism will shut off However the refrigeration system will continue to cool and maintain the cube supply Frost free ice maker units have lower ice production than manual defrost units IMPORTANT Do not place cans or bottles in the ice
32. t to assure that it is firmly in contact with the cabinet Also make sure the door gasket is not pinched on the hinge side of the door To align and adjust the door 1 Loosen do not remove top and bottom hinge screws 2 Align door squarely with cabinet 3 Make sure gasket is firmly in contact with cabinet all the way around the door no gaps 4 Tighten bottom hinge screws 5 Tighten top hinge screws Door Reversability Location of the unit may make it desirable to mount the door on the opposite side of the cabinet Models with black and white doors are field reversible Stainless steel models with glass doors without locks are field reversible Stainless steel models without glass doors must be ordered right or left hand hinged Reversing the door The Hinge hardware will be removed and reinstalled on the opposite side of the cabinet The hinge plate is flipped over when it is reinstalled on the opposite side of the cabinet 0 0 020 0901 00 Plastic Plug Hole Plastic Plug Hole Right a D TT Left Side Door Swin Door Swing To reverse the door Remove grille Remove the grille see MAINTENANCE section of this guide Remove top hinge and door 1 Hold door to keep it from falling 2 Remove top hinge from cabinet by removing three or four screws depending on model Ww Remove door by tilting forward and lifting door off bottom hinge 4 Remove three or four plastic screw plugs f
33. the bottom of the unit Ensure the condenser coil is clean and free of any dirt or lint build up Ice Cubes During periods of limited use or high ambient Sticking temperatures it is common for cubes to fuse Together together Gently shake the bucket to break apart cubes No Ice Ensure the bin arm is not in the up off position Production Not Enough Ice Ensure the condenser coil is clean and free of any dirt or lint build up Water in Bucket Ensure cube size adjustment is not se too high 16 U Line Combo Models and Ice Makers Service U Line Corporation Limited Warranty 1 U Line Corporation U Line warrants each U Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase U Line further warrants the sealed system consisting of the compressor the condenser the evaporator the hot gas bypass valve the dryer and the connecting tube in each U Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase 2 During the initial one year warranty period for all U Line products U Line shall 1 repair any product or replace any part of a product and 2 for all Marine RV and Domestic U Line products sold and serviced in the United States including Alaska and Hawaii and Canada U Line shall be responsible for the labor costs performed by a U Line authorized service company
34. ube size by changing water amount injected into the ice maker assembly as follows 1 Remove the ice maker assembly cover 1 2 Find the adjusting screw on the ice maker assembly control box 2 The adjusting screw is just below the minus and plus signs on the control box NOTE Adjust in small increments Too large of an adjust ment could cause the unit to malfunction NCAUTION Too large of an adjustment to the screw can cause the water to overflow the ice maker and can cause property damage 3 Turn the adjusting screw toward the minus sign clockwise for smaller cubes or toward the plus sign counterclockwise for larger cubes 4 Install the ice maker assembly cover U Line Ice Makers 7 7 Maintenance Leveling IMPORTANT Unit must be level for proper door and ice maker if equipped operation For Models with adjustable leveling feet 1 Use a level to check the levelness of the unit from front to back and from side to side Place the level along top edge and side edge as shown 1 2 Ifthe unit is not level rotate the adjustable leveling legs to raise or lower each corner of the unit 5 as necessary 3 Check levelness after each adjustment and repeat the previous steps until the unit is level For Models without adjustable leveling feet IMPORTANT
Download Pdf Manuals
Related Search