Tyco ADC 660P User's Manual
Contents
1. 16 17 CAMERA MOUNT 0 0 2 16 Il EXAMPLES OF CONNECTIONS 17 1 SIMPLEST ONE MONITOR SYSTEM WITH ONE CAMERA 17 2 ONE MONITOR SYSTEM WITH TWO OR MORE 8 17 1 18 IV SPECIFICATIONS 19 6 gt DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P oo 1 Video Output Connector BNC 1 0V 75 composite video signal is provided at this connector 2 Power Input Connector screw terminal FF AMERICAN 7 DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P This terminal accepts 12 VDC or 24 VAC Power Requirement Maximum 200 mA 12 VDC Maximum 100 mA 24 VAC Recommended Power Supply Minimum 500 mA 12 VDC Minimum 300 mA 24 VAC Caution Use a 24V AC 12V DC class 2 LPS supply only 3 Auto Iris Lens Connector for VIDEO Drive Lens This connector supplies 9 VDC power and video signal without sync for video drive ty2. 11 ALC Level Adjustment Potentiometer for DC Drive Lens This potentiometer is used only if the camera is fitted with a DC drive Auto Iris lens It is used to control the amount of light striking the CCD image sensor Turn off AGC With a brightly lit scene adjust LENS IRIS control for a clean 1 VPP video level with no blooming Turn AGC back on after adjustment is complete LENS IRIS level control K AMERICAN 13 DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P Monitor Screen LEVEL Control Direction To increase the brightness Clockwise To decrease the brightness Counterclockwise 12 Power Indicator LED This LED turns ON only when power is supplied properly and the DC DC converter or the regulator inside the camera works properly 13 Backfocus Adjustment Screw This screw is used to position the CCD image sensor at the precise point of focus of the lens Backfocusing Fixed Focal or Vari Focal Length Lenses Install a lens and connect the camera to a monitor and power supply as described in this manual Open the iris completely or just before there is blooming in the picture If an Auto lris lens is used reduce the room lighting to use a neutral density filter to allow the lens to open completely This gives the most accurate results Adjust the screw slowly until the sharpest picture is obtained This completes the adjustment The back focus adjustment screw i
3. 7 2 POWER INPUT CONNECTOR SCREW TERMINAL 5552 56 noe tere ko ERE Ue ER Re cup 7 3 IRIS LENS CONNECTOR FOR VIDEO DRIVE 1 14 n 8 4 AUTO IRIS LENS CONNECTOR FOR DC DRIVE 8 5 BLC BACKLIGHT COMPENSATION ON OFF SWITCH sess 9 6 ALC ELC SELECT SWITCH EE ELC is ON ALC AI IS 10 7 AGC ON OFF SWITCH 0 0 000 sss sans sas esas a sanas nasa danda 11 B INT LL LL is itik 11 9 FL ON SWITCH FLICKERLESS 11 10 V PHASE ADJUSTMENT 1 11 11 ALC LEVEL ADJUSTMENT POTENTIOMETER FOR DC DRIVE 5 13 12 POWER INDICATOR LED llli 14 13 BACKFOCUS ADJUSTMENT SCREW nene et tenes tr nzzzzzznrzzzzzzzzzzznzzzza 14 14 C MOUNT ADAPTOR RING 0 4000 0 tr essa sanas sess asa sss 16 15 CCD DUST PROTECTIVE 1 ss sas sse 16 16 CAMERA MOUNT 0
4. used outdoors or not never point it toward the sun Use caution when operating the camera in the vicinity of spot lights or other bright lights and light reflecting objects 5 Do not operate the camera beyond its temperature humidity or power source ratings Do not use the camera in an extreme environment where high temperature or high humidity exists Use the camera under conditions where temperatures are between 14 F 122 F 10 C 50 C and humidity is below 85 6 Use a 24V AC 12V DC class 2 LPS supply only Hi Res B W camera instruction manual ADC 660N and ADC 660P Copyright 2007 Sensormatic Electronics Corporation Product specifications subject to change without notice Certain product names mentioned herein may be trade names and or registered trademarks of other companies Customer Service Thank you for using American Dynamics products We support our products through an extensive worldwide network of dealers The dealer through whom you originally purchased this product is your point of contact if you need service or support Our dealers are empowered to provide the very best in customer service and support Dealers should contact American Dynamics at 800 507 6268 or 561 912 6259 or on the Web at www americandynamics net AMERICAN 5 DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P l CONNECTORS AND CONTROLS nara 7 1 VIDEO OUTPUT CONNECTOR
5. FF MIN ILLUMINATION F1 2 0 03 lux ELECTRONIC IRIS 1 60 1 100 000 SEC 1 50 1 100 000 SEC LINE LOCK RANGE 60 Hz 1 Hz 50 Hz 1 Hz BACKLIGHT COMPENSAT I ON ON OFF SELECTABLE CENTER ZONE WEIGHTED BACKFOCUS ADJUSTMENT FINE ADJUSTMENT WITH SELF LOCKING SYSTEM CAMERA MOUNT 1 4 20 UNC TOP or BOTTOM SELECTABLE LENS MOUNT C or CS MOUNT C MOUNT ADAPTOR RING INCLUDED AUTO IRIS SUPPORT VIDEO DRIVE TYPE WITH 3P TERMINAL DC DRIVE TYPE WITH 4P SQUARE CONNECTOR POWER REQUIREMENT 12V DC 20 200mA MAX 24V AC 20 100mA MAX OPERATION CONDITION 14 F TO 122 F 10 C 50 C WITHIN 85 RELATIVE HUMIDITY NET WEIGHT WITHOUT LENS APPROX 0 9 Ib 400 g DIMENSIONS W x H x L 2 2 in x 2 2 in x 5 55 in 55 x 55 x 141 mm AMERICAN DYNAMICS 19
6. connected to a switcher and the picture on the monitor rolls while switching from camera A to B adjusting the vertical phase V phase of the cameras will probably eliminate the rolling If this adjustment is necessary it should only be performed by a qualified technician Before making any adjustment confirm that cameras A and B are connected to the power supply with the same polarity To make an adjustment follow the steps below AMERICAN 11 DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P 1 While observing the video output signals from both cameras on an oscilloscope turn camera A s V phase control on back of camera until vertical sync from both cameras is in phase 2 f camera A s adjustment range is insufficient adjust camera B s V phase control in the opposite direction to camera A until they are in phase 3 If these adjustments do not bring vertical sync from both cameras phase recheck the polarity of the power supply connections Camera A s VIDEO OUT Camera B s VIDEO OUT Should be in phase If an oscilloscope is not available a less accurate adjustment can be made by observing the monitor and adjusting the V phase control potentiometer until no roll occurs on the monitor when switching back and forth between cameras A and B AMERICAN 12 DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P AC ADAPTOR SWITCHER
7. f field and the distant objects in a picture may be seen out of focus e Fixed iris or manual iris lenses may be used with the linear shutter EE ELC mode where the scene brightness varies over a limited range e Donot use the EE ELC mode when an Auto Iris lens is installed gt AMERICAN 10 DYNAMICS T Hi Res B W camera instruction manual ADC 660N and ADC 660P AGC ON OFF Switch This switch is provided for the AGC circuit The AGC circuit incorporated into the camera boosts the sensitivity automatically when the scene illumination is insufficient INT LL Switch LL is ON INT is OFF This camera can operate independently using its internal crystal controlled sync generator or it may be synchronized using line locking To select one or the other of these sync modes set the DIP switch on the rear panel to either INT or LL Switch 4 is set to ON for LL and OFF for INT If line lock is selected all the cameras in the system must be adjusted to begin the video field scan at the same time This is described in procedure 00 FL ON Switch Flickerless ON OFF This function is only used in JAPAN In order to use FL mode set EE AI switch to Al first and then FL ON OFF switch to ON When the DIP switch on the rear panel is set to ON the shutter speed is fixed at a rate of 1 100 120 sec V Phase Adjustment Potentiometer This potentiometer is set full counter clockwise at the factory If two or more cameras are
8. is used on the camera If a CS mount lens is used the adaptor is not necessary To install the adaptor first screw it into the lens mount opening on the camera Then screw the C mount lens into the adaptor LENS C MOUNT ADAPTER RING 15 CCD Dust Protective Cap Remove this cap before installing the lens Do not handle or leave the camera with cap open 16 Camera Mount Hole 17 Camera Mount Base 22 AMERICAN 16 E DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P 1 Simplest One monitor system with one camera AC ADAPTOR MONITOR CAMERA POWER VIDEO COAXIAL CABLE 2 One monitor system with two or more cameras AC ADAPTOR 8 CAMERA il EC NS VIDEO MONITOR 000000 I 12908822 SEQUENTIAL SWITCHER or QUAD SPLITTER AMERICAN 17 E DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P W 1 ji AD A 5 2 N al AMERICAN 18 Hi Res B W camera instruction manual ADC 660N and ADC 660P MODEL ADC660N ADC660P TV SYSTEM EIA CCIR EFFECTIVE PIXELS 768 H X 494 V 752 H X 582 V IMAGE DEVICE 1 3 INTERLINE TRANSFER CCD SCANNING SYSTEM 2 1 INTERLACE SYNCHRONIZING SYSTEM INTERNAL LINE LOCK SELECTABLE HORIZONTAL RESOLUTION 580 TV LINE VIDEO OUTPUT LEVEL 1 V pp 75 ohm S N RATIO MORE THAN 50 dB AGC O
9. of this equipment a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Equipment Modification Caution Equipment changes or modifications not expressly approved by Sensormatic Electronics Corporation the party responsible for FCC compliance could void the user s authority to operate the equipment could create a hazardous condition This class A digital apparatus complies with Canadian 5 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada Caution This installation should be made by a qualified service person and should conform to local and national electrical and mechanical codes 1 Do not attempt to disassemble the camera In order to prevent electric shock do not remove screws or cover There are no user serviceable parts inside 2 Do not expose the camera to rain or moisture or try to operate it in wet areas Take immediate action if the camera becomes wet Turn the power off and refer servicing to qualified service personnel Moisture can damage the camera and also create a danger of electric shock 3 Do not use strong or abrasive detergents when cleaning the camera body Use a dry cloth to clean the camera when dirty In a case where the dirt is hard to remove use a mild detergent and wipe gently 4 Never point the camera toward the sun Whether the camera is
10. p AMERICAN DYNAMICS Hi Res B W camera Instruction manual ADC 660N ADC 660P Version Rev A tyco Part Number 8200 0839 01 Notice WARNING To prevent fire or shock hazard do not expose the unit to rain or moisture The symbol is intended to alert the user to the presence of important operating N and maintenance servicing instructions in the literature accompanying the unit The symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of I sufficient magnitude to constitute a risk of electric shock to persons CAUTION RISK OF ELECTRIC SHOCK 00 NOT OPEN CAUTION To prevent electric shocks and CAUTION TO REDUCE THE RISK OF ELEC TRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALI FIED SERVICE PERSONNEL risk of fire hazards do NOT use other than specified power source Warning This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation
11. pe Auto lris lens PIN Signal l 1 GROUND an 2 POWER SUPPLY 9 VDC 40mA 3 VIDEO OUTPUT 0 7Vp p without sync When using a VIDEO drive lens the ALC ELC 1 must be set to the ALC OFF position 4 Auto Iris Lens Connector for DC Drive Lens This connector supplies the control signals to the DC drive Auto Iris lens 2 AMERICAN 8 DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P Autoiris lens cable If the cable is thick or the plug cover does not fit properly cut this rib away Back of camera 3 Signal Damp Damp Drive Drive Lens plug supplied EM191J 100 When using a DC drive lens the ALC ELC DIP 1 must be set to the ALC OFF position BLC Backlight Compensation ON OFF Switch If the subject you wish to view is too dim because of a bright background set the BLC DIP switch 2 to ON to compensate for the bright background With BLC on the background brightness may saturate in some cases This function may not operate properly if the object is too small compared to the area of the background This function can be used with either the linear shutter EE or ELC mode or an Auto Iris lens Al lens or ALC mode WITH BLC OFF WITH BLC ON FE AMERICAN 9 DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P 6 ALC ELC Select Switch EE ELC is ON ALC AI i
12. s OFF This switch is used to select EE electronic exposure ELC electronic light control mode or Al Auto Iris lens ALC automatic light control mode DIP switch 1 is set to ON for EE ELC and OFF for AI ALC In the EE ELC mode a continuously variable electronic shutter is employed to automatically control the exposure time of the CCD image sensor according to the incoming light level With this mode selected a fixed or manual iris lens can be used instead of an Auto lris lens In the AI ALC mode the CCD shutter speed is fixed to 1 60 1 50 sec and the incoming light level is controlled by the Auto Iris lens To use a video drive type or the DC drive type of Auto Iris lens set this switch to the ALC position Cautions e Under bright lighting conditions such as outdoors use an Auto Iris lens because the EE ELC control range is not wide enough under these conditions e Under certain unique lighting conditions the following phenomena may appear v Strong smear and or blooming on highlighted objects such as spotlights or windows Y Noticeable flicker in the picture and or color rendition variations To avoid this use an Auto Iris lens e When operating in EE ELC mode with manual iris lens the depth of field of the image may be less than that obtained by using an AI ALC lens Depth of field varies inversely with the iris opening Thus using this camera in EE ELC mode with the manual iris lens fully opened may result in less depth o
13. s held in place by friction so there is no locking screw to tighten Backfocusing Zoom Lenses Install a lens and connect the camera to a monitor and power supply Position the camera 10 30 feet 3 9 meters from a flat vertical surface suitable for focusing A newspaper works well as a focusing target Open the iris completely or just before there is blooming in the picture If an Auto lris lens is used reduce the room lighting or use a neutral density filter to allow the lens to open completely This gives the most accurate results 1 Zoom the lens in to the maximum telephoto setting Adjust the optical focus of the lens for the sharpest picture 2 Zoom out to the maximum wide angle setting If the picture is no longer in focus readjust the back focus screw to obtain the best focus possible 3 Repeat steps 1 and 2 until the image remains sharp through the entire zoom range without having to make any focus adjustments This completes the adjustment The back focus adjustment screw is held in place by friction so there is no locking screw gt AMERICAN 14 5 DYNAMICS Hi Res B W camera instruction manual ADC 660N and ADC 660P C W BACK FOCUS ADJ SCREV 15 Hi Res B W camera instruction manual ADC 660N and ADC 660P 14 Mount Adaptor Ring The C mount adaptor ring is used only if a C mount lens
Download Pdf Manuals
Related Search