Home

Trojan 30 User's Manual

image

Contents

1. 136401 10 AxleCollar 13362 25 Wire Retaining Clip 136431 Cm ade O o 26 Hopper Plug J nn 12 Axle Bushings 14951 27 Parts Package 1528r a BEL eo 4 Agitator O Parts included in Hopper Assembly
2. round hole CAUTION Do Not Compress Spring At This Time Feed wire through the square handle tube Be sure wire passes above the bolts in the handle brace Secure T handle to the tube with 1 1 4 20 x 2 1 4 hex bolts 2 washers and 1 hex nut in the holes Remove caution label and push the thumb release toward the centre and push down knob and shutoff spring until knob latches Wire Clip 5 Slide wire retaining clip onto wire as shown Insert wire through hole shutoff plate Slide wire retaining clip over shutoff plate and wire until the clip locks into place Shutoff Plate Wire Handle Grips 6 Install handle grips onto the handle as shown Soapy water will ease installation Do not use petroleum based products Insert screen into hopper by sliding it under the screen clips Screen Clips OPERATION 1 Check the product package for the rate setting and recommended swath width Turn the spreader OFF by pushing the control knob in Rotate the rate cam to the proper setting 2 The rate setting is adjusted by rotating the rate cam to the desired setting The rate cam locks at each setting 3 Always fill the spreader on the driveway or path not on the lawn Make sure spreader is in the OFF position Empty after each use 4 Start spreader moving then open spreader by pushing the thumb release to the ON position Always push spreader never pull Push knob down to close spread
3. APPROX SPREAD PARTICLE SIZE GRAMS SQUARE SETTING WIDTH IN METRES Large heavy particles Medium mixed particles Small particles nitrogen Mixed size particles some fines Light weight particles The conversions should be used as guidelines for establishing proper rate settings for the particular product being applied Steps for obtaining the most accurate settings are outlined in the How to Determine Spreader Settings and Spread Width section of this manual These settings are approximate and may vary due to physical characteristics of the product Walking speed wear condition of the turf and humidity may cause actual rate setting to deviate No expressed nor implied warranty or guarantee is provided as to coverage or uniformity indicated by these rate settings MAINTENANCE 1 Never store unused material in spreader Return Ps unused product to its original container T Oil Impeller Shaft 2 Wash spreader thoroughly after each use and dry Bearing In Hopper completely in sun or heated area Oil 3 Oil the axle bearings impeller shaft bearing in BY hopper control knob in _ hy i A AA an T handle N TROJAN gt 4 Remove gear cover and wash gears thoroughly Oil all bearing areas and face of gear teeth Re install gear cover 5 Gear mesh should be checked on a regular basis during high use periods Clearance between the axle gear and pinion gear should be minimal but not tight If adjust
4. Prizelawno calibrator for the Trojan 30 Trojan HVO and the Trojan Tow For all other spreaders standard calibration procedures should be followed Visit www sherriff amenity com for further information EFFECTIVE PATTERN WIDTH A simple visual pattern test can be made by operating the spreader over a non turf area and evaluating the pattern Space 1 0 on Centres Space for Wheel Track A more accurate method is to place a row of common disposable aluminum cake tins approximately 30 cm on centres Set the rate cam at a middle setting and make 3 or 4 passes in the same direction as shown Pour the material collected from each pan into individual bottles of the same size Set them side by side in order and visually inspect their volume The effective pattern width is the distance out from the spreader to a point where the amount of material is 1 2 the average amount in the center pans This distance is multiplied by 2 to achieve the total effective pattern width RATE SETTING CONVERSION The following provides MY ROJAN 30 approximate settings for those units listed fF TROJAN 30 7 Setting Prizelawn BF 1 SS HVO J N1 2 P1 2 T CBRIII Setting Lesco Hi WHEEL J L Setting Scotts R8A SR 1 J L T V AP amp SR2000 Setting The following provides approximate settings 12 TRO JAN 3 when only the product weight square dr di foot coverage and visual inspection of the material is available FERTILIZER BAG RATE
5. enity SHERRIFF AMENITY SHALL NOT BE LIABLE FOR ANY INCIDENTAL SPECIAL OR CONSEQUENTIAL LOSS DAMAGE OR EXPENSE DIRECTLY OR INDIRECTLY ARISING FROM THE USE OF ANY OF THE PRODUCT INCLUDING BUT NOT LIMITED TO DAMAGE OR LOSS OF OTHER PROPERTY OR EQUIPMENT LOSS OF PROFITS OR REVENUE COST OF CAPITAL COST OF PURCHASED OR REPLACEMENT GOODS OR CLAIMS OF CUSTOMERS OF PURCHASER Parts List 13 12 11 PART OF OUR SERVICE IS PROVIDING REPLACEMENT Sherriff Amenity PARTS Parts may be obtained The Pines Fordham Road IF YOUR LOCAL DISTRIBUTOR Newmarket Suffolk CB8 7LG 1 SPREADER MODEL NUMBER CANNOT SUPPLY PARTS 2 SPREADER NAME CONTACT nn 3 PART NUMBER fax 01638 721815 www sherriff amenity com 4 NAME OF PART AS SHOWN Key Description W TROJAN Key Description TROJAN 2 No Part No No Part No 1 Hopper Assembly 15383 15 Impeller Shaft Bearing 14312 1 152770 16 Hopper Screen 14603 1 2 Shutoff Plate 144541 17 Screen Clips 2 14022 3 Shutoff Plate Guides 2 15377 18 Handle Brace W Plug LH 15378 4 Rate Cam amp Chute Assembly 144551 19 Handle Brace W Plug RH 15379 5 Impeller Assembly 15263 20 HandleTube 152834 6 Frame Assembly 162622 21 HandieGrips 15264 7 Drive Whee 14939 1 22 T Handie Assembly 136342 8 AxleGear 48360 23 Control Knob Spring 14462 9 Gear Cover Assembly 44628 24 Control Knob amp Wire Ass y
6. er 5 Hold handle so top of spreader is level Tipping the spreader too far can cause uneven spreading 6 The settings and swath widths on the product label are recommended starting points Always check the delivery rate and pattern on a small area before treating a large area Actual delivery rate can vary due to weather conditions operating variables and condition of the product being applied See HOW TO DETERMINE SPREADER SETTING AND SWATH WIDTH for details 7 Push spreader 2 1 2 m p h 5 5 metres in 5 seconds for full 8 to 14 spread pattern when applying fertilizer products Apply header strips at each end of area to be treated then space trips across the area as shown OFF USE SWATH WIDTH ON PACKAGE OR ADJUST PER OPERATOR S WALKING SPEED 8 Empty spreader after each use Return leftover material to its original container HOW TO DETERMINE SPREADER SETTINGS AND SPREAD WIDTH Two major factors should be considered when determining correct spreader settings of any product 1 The product application rate or the amount of material applied per 500 square metres 2 The effective pattern width or the actual width in which material is applied Label settings are a guide and can be affected by numerous factors The Trojan 30 is factory calibrated However calibration should be checked occasionally to assure optimum performance For accurate calibration Sherriff Amenity recommends the use of the
7. mal lt Z lt L Ss 07 Ll Z O ASSEMBLY 1 4 20 x 2 1 4 RH Handle Hex Bolt 1 Remove components from carton E 27 0 and place spreader upside down on a padded surface Install LH 8 RH handle braces to frame as shown using four 4 1 4 20 x 2 1 4 hex bolts and nuts but do not tighten 114 20 Hex Nut 5 32 Dia x 2 Cotter Pin 4 LH Handle Brace Drive Wheel 1 8 Dia x 1 2 Install drive wheel onto right hand fe Cotter Pin end of axle you can identify the drive wheel by the cotter pin hole drilled in the J hub Hub must face toward frame Align a the hole in the drive wheel hub and the hole in the axle Secure drive wheel to axle with 5 32 dia x 2 cotter pin Install the free wheel on the opposite end of axle Insert 5 32 dia x 1 cotter pin in the Free Whee hole near the end of axle to retain free wheel 1 4 20 x 1 1 2 Hex Bolt 3 Turn spreader upright and install end of handle tube with DOT between handle braces as shown Secure with 2 1 4 20 x 1 1 2 hex bolts and nuts 5 114 20 Hex Nut Control Knob amp R Cauti eal en ee Wire Assembly Spring Thumb ra Release A 14 20 x 2 1 4 Bolt amp Washer i D tao 1 4 20 Hex Nut amp Washer CAUTION Once knob is latched do not move thumb release until completed in step 5 ou have 4 Feed control knob wire through the T handle until spring touches the
8. ment is necessary loosen axle collar set screw and hold gears together Slide axle collar against the gear support and tighten axle collar set screw Spin drive wheel Gears should run freely and smoothly Axle Collar 6 Impeller surface should be cleaned periodically to remove build up of product Build up can cause the spread pattern to change 7 Tyre pressure should be 20 25 PSI WARRANTY Sherriff Amenity warrants to Purchaser the following 1 Product will be free of defects in materials and workmanship for a period of one year from date of purchase 2 Sherriff Amenity will decide in its reasonable discretion if the part s unit is defective 3 The spreader or part s will be shipped to Sherriff Amenity at the customer expense with a written description of defect to the attention of Sherriff Amenity s WARRANTY DEPARTMENT 4 If the spreader is used for commercial rental the Limited Warranty shall be limited to a period of 90 days 5 All Unit and part replacement will be performed at the reasonable discretion of Sherriff Amenity 6 Labor charges are not covered and the unit need not be returned to the dealer for warranty service 7 Proof of purchase must be supplied to Sherriff Amenity Sherriff Amenity s sole obligation under this warranty is limited to repairing or replacing the defective part Upon replacement of any Product or Product part the replaced item shall become the property of Sherriff Amenity If Sherriff Ame
9. nity determines that the Product covered by this warranty requires service Sherriff Amenity shall prepay return shipping charges from Sherriff Amenity In all other instances such charges shall be paid by Purchaser Except for loss or damage caused by Sherriff Amenity s negligence Purchaser relieves Sherriff Amenity of responsibility for all risks of loss or damage to the Product and its parts during the period the products are in transit to and from Sherriff Amenity This warranty does not extend to any Product or parts thereof that have been allowed to corrode subjected to misuse neglect accident or modification by anyone other than Sherriff Amenity or that have been affixed to any nonstandard accessory attachment or that have been used stored installed maintained or operated in violation of Sherriff Amenity s instructions or standard industry practice No agent employee or representative of Sherriff Amenity has any authority to bind Sherriff Amenity to any affirmation representation or warranty concerning the Product and any affirmation representation or warranty made by any agent employee or representative shall not be enforceable by Purchaser THIS WARRANTY EXTENDS ONLY TO THE ORIGINAL PURCHASER AND IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS OR INTENDED USE FORA PARTICULAR PURPOSE AND OF ANY OTHER OBLIGATION ON THE PART OF Sherriff Am

Download Pdf Manuals

image

Related Search

Related Contents

AVALIAÇÃO PERFIL DE ESTUDO  Barriera luminosa/Tipo 2 Serie SF2C Manuale di istruzioni  MhouseKit - Leroy Merlin  Manual Video Viewer  Airlink101 AR504 Typewriter User Manual  

Copyright © All rights reserved.
Failed to retrieve file