Triton Tools Lithium Ion Cordless Screwdriver User's Manual
Contents
1. FORWARD REVERSE SWITCH Use the direction switch 2 on the top of the screwdriver to select forward or reverse driving e To select forward when screwing in fasteners slide the switch back away from the hex drive e Slide the switch toward the hex drive to select reverse when removing fasteners HEX DRIVE The hex drive 3 is designed to accept commonly available 6mm hex bits A selection of eighteen bits 7 are supplied to cover most driving applications Sizes are marked on the sides of the bit holders The driver bits are fitted by pushing their hexagonal end fully into the hex drive 3 2 A magnetic extension piece 8 is supplied to reach fasteners in difficult locations Push the extension into the hex drive then fit the driver bit into the end of the extension piece A A magnet ensures that EN the bit locates fully into the extension 3 To remove the bit from the hex drive or the magnetic extension firmly grasp the bit between your fingers and pull outward CHARGER e The screwdriver is supplied uncharged and must be fully charged prior to initial use e The screwdriver will require 5 to 10 charge discharge cycles before it reaches its full capacity e It is acceptable to charge a partially discharged battery to ensure maximum output for the job e Most charge cycles will require 3 5 hours A Warnings e Do not charge the tool in a damp or wet environm2. use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury General Safety Rules 5 Use safety equipment Always wear eye protection Safety equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries Dress properly Do not wear loose clothing or jewellery Tie back long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents Remove adjusting keys or wrenches before turning the tool on A wrench or a key that is left attached to a rotating part of the tool may result in injury Accessories and metal parts can become very hot POWER TOOL USE AND CARE 6 Use clamps or other practical way to secure and support the work to a stable platform Holding the work by hand or against your body is unstable and may lead to loss of control Do not force the tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for General Safety Rules which it is designed Do not use the tool if
3. TLS Thank you for purchasing this Triton power tool These instructions contain information necessary for safe and effective operation of this product Keep this manual close to hand and ensure all users of this tool have read and fully understand them Specifications 3 Model no TLS Features 4 Voltage 3 6V De gt Charger 230 240V 50Hz Symbols 8 Charge time 3 5 hours Functions 9 Service il No load speed 200min Warranty 12 Net weight 300g 10 61b Triton Offices 13 Torque 5Nm 2 Contents Specifications 3 I Trigger switch 2 Forward reverse switch 3 Hex drive 4 Charger connection point 5 Charge indicator 6 Charger 7 Driver bits 8 Magnetic extension 4 Slotted 50mm Philips 50mm Philips 25mm Slotted 25mm Hex 25mm Star 25mm H2 0 1 2 3 4 5 6 mm 3 4 5 6mm T15 T20 T25 T30 Features Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury The term power tool in all of the warnings listed below refers to your mains operated corded power tool or battery operated cordless power tool SAVE THESE SAFETY INSTRUCTIONS e Keep your work area clean and well lit Cluttered benches and dark areas invite accidents Do not operate power tools in an environment where explosive or corrosive gases could be pres
4. art proves to be defective due to faulty materials or workmanship within 12 MONTHS from the date of original purchase Triton will repair or at its discretion replace the faulty part free of charge This warranty does not apply to commercial use nor does it extend to normal wear and tear or damage as a result of accident abuse or misuse If product is faulty or requires service please phone 300 655 686 for referral to your nearest authorised Triton Repair Centre Warranty does not include any freight to and from the user If outside of Australia please contact your nearest Triton office details on the next page for arrangements to repair or replace the product Date of Purchase __ Model TLS Retain your receipt as proof of purchase Serial Number Located on motor label 12 Warranty Australia South Africa Triton Manufacturing amp Design Co Tritonova 45 55 South Centre Rd PO Box 6391 Melbourne AirportVic 3045 Welgemoed 7538 Ph 03 9584 6977 Ph 0800 600432 Fax 03 9584 5510 Fax 021 987 6073 Canada United Kingdom Triton Woodworking Systems Triton Workshop Systems UK Ltd PO Box 523 Pontygwindy Industrial Estate Cornwall Ontario K6H 5T2 Caerphilly South Wales CF83 3HU Ph 888 874 8661 Ph 0800 856 7600 Fax 613 938 8089 Fax 029 2085 0118 Japan USA Japan Australia Corp Pty Ltd Triton Woodworking Systems 195 Kanaido SOJA shi PO Box 794 Rooseveltown Okayama Ken 719 1114 New Yor
5. by qualified repair personnel e Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained Triton Manufacturing amp Design Co will not be responsible for any damage or injury caused by unauthorised repair or mishandling of the tool POWER CORD MAINTENANCE If the supply cord needs replacing the task must be carried out by the manufacturer the manufacturer s agent or an authorised service centre in order to avoid a safety hazard CLEANING Exterior plastic parts may be cleaned a damp cloth and mild detergent Although these parts are highly solvent resistant NEVER use solvent Dirt and grease may be removed from the exterior of the charger using a cloth or soft non metallic brush Do not use water or any cleaning solutions Disconnect the charger from the power point before cleaning Service amp Maintenance To register your warranty complete the registration card included in this manual and return it to your nearest Triton office listed below Alternatively you can register online by visiting our web site www triton net au Your details will be included on our mailing list unless indicated otherwise for information on future releases Details provided will not be made available to any third party Triton Manufacturing amp Design Co warrants to the purchaser of this product that if any p
6. ent e To prevent overheating do not cover the charger and do not charge in direct sunlight Functions 9 or near heat sources Do not attempt to charge the screwdriver with any charger other than that supplied with the tool Contact your local Triton office if charger replacement is required Avoid charging your screwdriver in temperatures below 0 C 32 F and over 40 C 104 F Push the connection pin on the charger 6 into the charger connection point 4 on the base of the screwdriver handle SHAFT LOCK This screwdriver is fitted with an automatic shaft lock With the trigger switch dis engaged it can be used for manual screwdriving Connect the mains plug of the charger to a suitable power point A The red LED charge EN light indicator 5 will illuminate for the duration of the charge cycle The charge cycle should take between 3 and 5 hours after which the charge light indicator 5 will switch off The charger should be disconnected from mains power on completion of the charge cycle Do not exceed 2 hours of connection to mains power Disconnect the charger from the power point before removing the connection pin from the screwdriver A While charging the charger EA and the screwdriver may become warm to touch This is normal and does not indicate a problem 10 Functions e Any damage to this tool should be repaired and carefully inspected before use
7. ent Power tools create sparks which may ignite fumes Avoid areas where there is excessive dampness or humidity Keep children bystanders and visitors away while operating the power tool Distractions can cause you to lose control e Always set up or fix the tool in a stable position ELECTRICAL SAFETY e Power tool plugs must match the outlet Never modify the plug in any way Do not use any adaptor plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock e Avoid body contact with earthed grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded e Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock e When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock e Never yank the cord to disconnect if from socket Keep the cord away from heat and sharp edges PERSONAL SAFETY Stay alert watch what you are doing and use common sense when operating a power tool Do not
8. k 13683 0794 Ph 0866 90 1415 Ph 888 874 866 Fax 0866 90 1417 Fax 613 938 8089 New Zealand Triton Manufacturing amp Design Co Ph 0508 874 866 Fax 0508 3944557 Triton Offices 13 1435 OL 3903 SIHLDNOTV 3dVL TLS Warranty Registration Card Mr Ms Mrs Address Postcode Ph Private Ph Business don t wish to be included on your mailing list Serial No Purchase date Retailer Age Under 25 25 35 36 45 46 55 56 65 Over 65 Occupation Please list any other Triton products you own Fold here Comments Suggestions Our aim is to provide innovative quality products which are excellent value for money If you have any comments on how we can improve our products or service please let us know 7 X TAPE ALONG THIS EDGE TO SEAL TO PLEASE AFFIX STAMP
9. protection when using this tool Position yourself to avoid being caught between the tool and walls or posts Should the screw become bound or jammed in the work the reaction torque of the tool could crush your hand or leg Do not run the screwdriver while carrying it at your side A spinning bit could become entangled with clothing and injury may result ADDITIONAL SAFETY WARNINGS FOR THE CHARGER e Use only the charger supplied in this pack Protect the charger against moisture including rain and high humidity Always check that the power cord is correctly connected before using the charger e When you are not using the charger remove the plug from the mains socket Do not pull the plug out by the power cord e Always remove the plug from the power socket before you clean or maintain the charger Do not charge the battery if the ambient temperature is less than 10 C 14 F or greater than 40 C 104 F General Safety Rules 7 ENVIRONMENTAL PROTECTION Waste electrical products X should not be disposed of with household waste Please recycle where facilities exist Check with your local authority or retailer for recycling advice oop Always wear ear eye and s respiratory protection o Double insulated A Instruction warning A Instruction note 8 Symbols TRIGGER SWITCH e To operate the screwdriver engage the trigger switch 1 e Release the switch to stop
10. switch does not turn it on or off Any tool that cannot be controlled with the switch is dangerous and must be repaired If there appears to be a problem refer to the Trouble shooting and if necessary contact a repair centre Disconnect the plug from power before making any adjustments changing accessories or storing the tool Such preventative measures reduce the risk of accidental starting Store tool in a dry location out of reach of children and untrained persons This tool is dangerous in the hands of untrained users Maintain tools with care Keep cutting tools sharp and clean Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control Check for misalignment ie excessive vibration binding of moving parts or any damage that may affect the tools operation lf damaged have the tool serviced before using Many accidents are caused by poorly maintained tools Never start the tool while the blade is touching the workpiece ADDITIONAL SPECIFIC SAFETY RULES I Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring Contact with a live wire will make exposed metal parts of the tool live and shock the operator 2 Be aware that this tool is always in an operating condition because it does not have to be plugged into an electrical outlet Always wear safety goggles or eye
Download Pdf Manuals
Related Search