Tripp Lite OMNI1500LCD User's Manual
Contents
1. Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference using one or more of the following measures reorient or relocate the receiving antenna increase the separation between the equipment and the receiver connect the equipment into an outlet on a circuit different from that which the receiver is connected consult the dealer or an experienced radio television technician for help The user must use shielded cables and connectors with this product Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with part 15 of the FCC rules Operation is subject to the following 2 conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Equipment Attachm2. electrician as appropriate Regulatory Compliance Identification Numbers Note on Labeling aa rrr he For the purpose of regulatory compliance certifications and identification your Tripp Lite product has been assigned a unique series number The series Two symbols are used on the label number can be found on the product nameplate label along with all required approval markings and information When requesting compliance information V AC Voltage for this product always refer to the series number The series number should not be confused with the marking name or model number of the product DC Voltage Tripp Lite follows a policy of continuous improvement Product specifications are subject to change without notice TRIPP L ITE 1111 W 35th Street Chicago IL 60609 USA www tripplite com support 4 201004199 e 932668 EN
3. leave connected equipment on during a self test MUTE TEST Button CAUTION Do not unplug your UPS to test its battery This will remove safe electrical grounding and may introduce a damaging surge into your network connections Results of a Self Test The test will last approximately 10 seconds as the UPS switches to battery to test its load capacity All LCD Display icons will be illuminated and the UPS alarm will sound e If the FAULT icon remains lit and the alarm continues to sound after the test the outlets are overloaded To clear the overload unplug some of your equipment from the outlets and run the self test repeatedly until the FAULT icon is no longer lit and the alarm is no longer sounding CAUTION Any overload that is not corrected by the user immediately following a self test may cause the UPS to shut down and cease supplying output power in the event of a blackout or brownout e If the REPLACE icon remains lit and the alarm continues to sound after the test the UPS batteries need to be recharged or replaced Allow the UPS to recharge continuously for 12 hours and repeat the self test If the icon continues to illuminate after repeated self tests contact Tripp Lite for service Battery replacement should only be performed by qualified service personnel If the UPS requires battery replacement Tripp Lite offers a complete line of replacement batteries at www tripplite com Basic Operation Front Pane
4. pause to indicate the UPS is operating from its internal batteries Monitor the Battery Capacity Meter to determine the approximate battery charge level available to support equipment During a prolonged brownout or blackout the alarm will sound continuously and the BATTERY CAPACITY Meter will show one 20 capacity segment shaded to indicate the UPS s batteries are nearly out of power you should save files and shut down your equipment immediately Eid FAULT Icon This icon will illuminate and an alarm will sound after a self test to indicate the outlets are overloaded To clear the overload unplug some of your equipment from the outlets and run the self test repeatedly until the icon is no longer illuminated and the alarm is no longer sounding EG LCD Dimmer Adjusts the brightness of the LCD Status Screen Basic Operation Rear Panel NORM DELAY 6 9 Battery Backup Surge Only RS 232 Port USB Port Tel DSL Removabe Power Sensitivity Dial Protected Surge Protected Outlets Select models only Network Jacks Mounting Hardware Protected Outlets Select models only EI Battery Backup Protected Surge Protected Outlets Provide connected equipment with AC line power backed by surge protection and line noise filtering during normal operation Automatic voltage regulation continually corrects brownout low voltage and high voltage conditions without using battery power Provide battery power during blackouts and seve
5. Owner s Manual s SMART1200LCD SMART1500LCD amp OMNI1500LCD A C is TESTED TO Se a g UL 1778 S CSA 22 2 No 107 3 Ami be Tested To Comply With FCC Standards FOR HOME OR OFFICE USE R o Hi S COMPLIANT Not suitable for mobile applications English 1 Espa ol 5 Fran ais Q Important Safety Instructions AN SAVE THESE INSTRUCTIONS This manual contains instructions and warnings that should be followed during the installation operation and storage of all Tripp Lite UPS Systems Failure to heed these warnings may affect your warranty UPS Location Warnings e The UPS is designed for indoor use only in a controlled environment away from excess moisture heat cold conductive contaminants dust or direct sunlight e Leave adequate space around all sides of the UPS for proper ventilation e Do not mount unit with its front or rear panel facing down at any angle Mounting in this manner will seriously inhibit the unit s internal cooling eventually causing product damage not covered under warranty UPS Connection Warnings e Connect your UPS directly to a properly grounded AC power outlet Do not plug the UPS into itself this will damage the UPS e Do not modify the UPS s plug and do not use an adapter that would eliminate the UPS s ground connection e Do not use extension cords to connect the UPS to an AC outlet e If the UPS receives power from a motor powered AC gene
6. ent Limitations models with the Industry Canada label in Canada only NOTICE The Industry Canada label identifies certified equipment This certification means that the equipment meets the telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements Document s The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that the compliance with the above conditions might not prevent degradation of service in some situations Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make connections themselves but should contact the appropriate electric inspection authority or
7. ion and operation procedures in this manual to insure that the service problem does not originate from a misreading of the instructions N If the problem continues do not contact or return the product to the dealer Instead visit www tripplite com support eS If the problem requires service visit www tripplite com support and click the Product Returns link From here you can request a Returned Material Authorization RMA number which is required for service This simple on line form will ask for your unit s model and serial numbers along with other general purchaser information The RMA number along with shipping instructions will be emailed to you Any damages direct indirect special or consequential to the product incurred during shipment to Tripp Lite or an authorized Tripp Lite service center is not covered under warranty Products shipped to Tripp Lite or an authorized Tripp Lite service center must have transportation charges prepaid Mark the RMA number on the outside of the package If the product is within its warranty period enclose a copy of your sales receipt Return the product for service using an insured carrier to the address given to you when you request the RMA Warranty Registration Visit www tripplite com warranty today to register the warranty for your new Tripp Lite product You ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product No purchase necessary Void where pr
8. l continued EI LCD Display The LCD Display indicates a variety of UPS operational conditions All descriptions apply when the UPS is plugged into an AC outlet and turned on The LCD Display can be rotated for easy viewing regardless of whether the UPS is in a horizontal or vertical tower position To rotate the display insert a small tool in the slots on the sides of the display to pop it out of the UPS housing rotate the display and snap it back into the UPS housing Er Input Voltage Meter This meter measures in real time the AC voltage that the UPS system is receiving from the utility wall outlet Although the meter may occasionally display input voltages which stray due to poor quality utility service outside the range of standard computer tolerance rest assured BATTERY CAPACITY that the UPS is designed through the use of automatic voltage regulation to continuously supply connected equipment with stable computer grade output voltage In the event of a blackout power loss severe brownout low power or overvoltage high power the UPS will rely on its internal battery to supply computer grade output voltage The Input Voltage Meter can be used as a diagnostic tool to identify poor quality input power By plugging the UPS into different outlets within a facility you can LCD Display identify individual circuits that are consistently providing low power which can be caused by the combined equipment load dema
9. lace it in the ON position again 3 If your UPS had an ON OFF button you must press it for at least one second to start the UPS A beep should sound when the UPS starts 4 If the UPS still does not start contact Tripp Lite Tech Support for assistance Basic Operation Front Panel El ON OFF Button e To turn the UPS on Press and hold the ON OFF Button for one second If utility power is absent pressing the Button will cold start the UPS i e turn it on and supply power from its battery e To turn the UPS off Press and hold the ON OFF Button for one second The UPS will be turned completely off deactivated The alarm will beep once briefly after one second has passed Providing runtime proportionate to the UPS battery s level of charge 1 Note UPS system will function properly upon initial startup however maximum runtime for the unit s battery will only be ON OFF Button accessible after it has been charged for 24 hours A MUTE TEST Button e To Silence or Mute UPS Alarms briefly press and release the MUTE TEST button Note continuous alarms warning you to immediately shut down connected equipment cannot be silenced e To Run a Self Test with your UPS plugged in and turned on press and hold the MUTE TEST button for two seconds Continue holding the button until the alarm beeps several times and the UPS performs a self test See Results of a Self Test 2 below Note you can
10. nding more power than the circuit is designed to supply If all circuits within a facility consistently provide low power the facility may be served by inadequate utility service or may be in an industrial or commercial area with an overburdened power grid EIJ BATTERY CAPACITY Meter This meter displays the approximate charge level in 20 increments of the UPS s internal battery During a blackout or severe brownout the UPS will switch to battery power the ON BAT icon will be illuminated and the charge level will deplete ETJ AVR Automatic Voltage Regulation Icon This icon will illuminate whenever your UPS is automatically correcting low AC line voltage without depleting battery power This is a normal automatic operation of your UPS and no action is required on your part EG REPLACE Battery Recharge Replace Icon This icon will illuminate and an alarm will sound after a self test to indicate the UPS battery needs to be recharged or replaced Allow the UPS to recharge continuously for 12 hours and repeat the self test If the icon continues to illuminate contact Tripp Lite for service Battery replacement should only be performed by qualified service personnel If the UPS requires battery replacement Tripp Lite offers a complete line of replacement batteries at www tripplite com Ef ON BAT On Battery Icon During a severe brownout or blackout this icon illuminates and an alarm sounds 4 short beeps followed by a
11. ohibited Some restrictions apply See website for details FCC Part 68 Notice United States Only If your Modem Fax Protection causes harm to the telephone network the telephone company may temporarily discontinue your service If possible they will notify you in advance If advance notice isn t practical you will be notified as soon as possible You will be advised of your right to file a complaint with the FCC Your telephone company may make changes in its facilities equipment operations or procedures that could affect the proper operation of your equipment If it does you will be given advance notice to give you an opportunity to maintain uninterrupted service If you experience trouble with this equipment s Modem Fax Protection please call Tripp Lite Technical Support at 773 869 1234 for repair warranty information The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure the equipment is not malfunctioning There are no repairs that can be made by the customer to the Modem Fax Protection This equipment may not be used on coin service provided by the telephone company Connection to party lines is subject to state tariffs Contact your state public utility commission or corporation commission for information FCC Radio TV Interference Notice U S only Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to
12. put can be evaluated without disrupting critical operations The experiment should last long enough to assure that all expected line conditions are encountered Battery Replacement Under normal conditions the original battery in your UPS will last several years Battery replacement should be performed only by qualified service personnel Refer to Battery Warnings in the Safety section Should your UPS require battery replacement visit Tripp Lite on the Web at www tripplite com support battery index cfm to locate the specific replacement battery for your UPS Storage and Service Storage To avoid battery drain all connected equipment should be turned off and disconnected from the UPS Press and hold the ON OFF button for one second Your UPS will be completely turned off deactivated and will be ready for storage If you plan on storing your UPS for an extended period fully recharge the UPS batteries every three months Plug the UPS into a live AC outlet turn it on by pressing and holding the ON OFF button for one second and allow the batteries to recharge for 4 to 6 hours If you leave your UPS batteries discharged for a long period of time they will suffer a permanent loss of Capacity Service A variety of Extended Warranty and On Site Service Programs are available from Tripp Lite For more information on service visit www tripplite com support Before returning your product for service follow these steps 1 Review the installat
13. rator the generator must provide clean filtered computer grade output e The UPS contains its own energy source battery The output terminals may be live even when the UPS is not connected to an AC supply Equipment Connection Warnings e Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended Do not use this equipment in the presence of a flammable anesthetic mixture with air oxygen or nitrous oxide e Do not connect surge suppressors or extension cords to the output of your UPS This might damage the UPS and may affect the surge suppressor and UPS warranties Battery Warnings e Your UPS does not require routine maintenance Do not open your UPS for any reason There are no user serviceable parts inside e Batteries can present a risk of electrical shock and burn from high short circuit current Observe proper precautions Do not dispose of the batteries in a fire Do not open the UPS or batteries Do not short or bridge the battery terminals with any object Unplug and turn off the UPS before performing battery replacement Use tools with insulated handles There are no user serviceable parts inside the UPS Battery replacement should be performed only by authorized service personnel using the same number and type of batteries Sealed Lead Acid The batteries are rec
14. re brownout or severe high voltage conditions DO NOT PLUG LASER PRINTERS INTO ANY OF THESE OUTLETS 5 Surge Only Protected Outlets Provide surge and line noise protection but NOT battery backup Plug equipment that does not require battery backup during a utility power failure such as printers scanners or fax machines into these outlets O USB and RS 232 Communication Ports These ports can connect your UPS to any computer for automatic file saves and unattended shutdown in the event of a power failure Use with Tripp Lite s PowerAlert Software available as a FREE download at www tripplite com and appropriate USB or DB9 cable A USB or DB9 cable may be included with your UPS If the appropriate cable did not come with your UPS any user supplied DB9 pass through or USB cable may then be used to connect your UPS to your computer Note This connection is optional The UPS will work properly without this connection Also Note This UPS System provides basic communication compatibility with most integrated Windows Macintosh and Linux power management applications Tel DSL Network Line Surge Protection Jacks Your UPS has jacks that protect against surges on a single phone fax modem or Ethernet network line Using appropriate telephone or network cords connect your wall jack to the UPS jack marked IN Connect your equipment to the UPS jack marked OUT Make sure the equipment you connect to the UPS s jacks is also protected against
15. surges on the AC line Connecting your equipment to these jacks is optional Your UPS will work properly without this connection Not compatible with PoE Power Over Ethernet applications E Removable Mounting Hardware Adapts the UPS to either tower or rackmount 2U applications Basic Operation Rear Panel continued EJ Power Sensitivity Dial This dial is normally set fully counterclockwise which enables the UPS to protect against waveform distortions in its AC input When such distortion occurs the UPS will normally switch to providing PWM sinewave power from its battery reserves for as long as the distortion is present In some areas with poor utility power or where the UPS s input power comes from a backup generator frequent brownouts and or chronic waveform distortion could cause the UPS to switch to battery too often draining its battery reserves You may be able to reduce how often your UPS switches to battery due to waveform distortion or brownouts by experimenting with different settings for this dial As the dial is turned clockwise the UPS becomes more tolerant of variations in its input power s AC waveform NOTE The further the dial is adjusted clockwise the greater the degree of waveform distortion the UPS will allow to pass to connected equipment When experimenting with different settings for this dial operate connected equipment in a safe test mode so that the effect on the equipment of any waveform distortions in the UPS s out
16. ure types and may not be appropriate for all applications STEP 2 Plug the UPS into an outlet After plugging the UPS into a wall outlet push the ON OFF button for one second to turn the UPS on see Basic Operation section Please Note The UPS will not turn on automatically in the presence of live utility power STEP 3 Plug your equipment into the UPS Your UPS is designed to support electronic equipment only You will overload the UPS if the total VA ratings for all the equipment you connect to the outlets exceeds the UPS s Output Capacity To find your equipment s VA ratings look on their nameplates If the equipment is listed in amps multiply the number of amps by 120 to determine VA Example 1 amp x 120 120 VA If you are unsure if you have overloaded the outlets run a self test see MUTE TEST Button description STEP 4 Optional Installation All models include USB and RS 232 communication ports as well as Tel DSL network surge protection jacks These connections are optional the UPS will work properly without these connections See the connector s description in the Basic Operation section for connection instructions If the LINE POWER indicator light LCD screen on Digital models does not illuminate when the UPS is turned ON try the following 1 Make sure that the UPS is plugged into a live AC outlet 2 If your UPS has a sliding ON OFF switch place it back in the OFF position wait several seconds then p
17. yclable Refer to your local codes for disposal requirements or visit www tripplite com UPSbatteryrecycling for recycling information Tripp Lite offers a complete line of UPS System Replacement Battery Cartridges R B C Visit Tripp Lite on the Web at www tripplite com support battery index cfm to locate the specific replacement battery for your UPS e Do not attempt to add an external battery pack to the UPS TRIPP LITE 1111 W 35th Street Chicago IL 60609 USA www tripplite com support Copyright 2010 Tripp Lite All rights reserved All trademarks are the property of their respective owners Quick Installation STEP 1 To install the UPS in a 4 post rack attach the included mounting hardware to the UPS as shown in diagram EN To mount the UPS in a 2 post rack attach the included hardware to the UPS as shown in diagram E Then using an assistant if necessary lift the UPS and attach it to a standard rack or rack enclosure with user supplied hardware Caution If the UPS is installed in a rack allow at least 0 75 in 2 cm clearance above and below the unit If the UPS is placed flat on a surface do NOT stack any other object directly on top of the unit The UPS will stand in a tower position without the aid of the included hardware However for added stability Tripp Lite recommends that the included hardware be attached as shown in diagram A The UPS and included hardware are designed for common rack and rack enclos
Download Pdf Manuals
Related Search