Triarch 2LTS User's Manual
Contents
1. 31441 2 LTS Semi Flush Fixture Assembly Instruction Sheet Thread the top loop onto the center treaded stem on the top of the Column Assemble Thread until tighten Follow the wattage label on the socket and install correct type and wattage bulb onto the bulb socket Fix the steel cap onto the center column assemble by through the center stem to the center hole of the steel cap Fix the glass shade onto the center stem assemble by through the center hole of the glass by center stem of the center column assemble Place the metal washer onto the center stem and secured by thread the nut to the threaded stem Thread the until tighten Place the bottom cover onto the center stem Fix the bottom finial onto the center stem Thread until tighten 4 Measure the height for the fixture to your ceiling and cut the excess chain and wire to fit the height Wire connection step please see the mounting instruction sheet Q LOOP B NIPPLE aaneen COUPLER eS wpput fo TUBE CAP c gt lt COVER METAL WASHER pat MOUNTING AND WIRING INSTRUCTIONS 1 Fasten mounting strap lo junction box with machine screws found in junction box The moutling suap must be Used to provide proper grounding of fixture 2 Turn nipple into threaded hole in the mounting strap Turn hex nut onto nipple Remove knurled nut from hang acloop Tum hanger toop onto nipple Place canopy up against ceiling and adjust ni2. d of bare wke to the house ground wire bate If tha junction box itself is metal and Is already grounded attachment to the green screw only Is sufficient Always use wire connectors thal are UL approved for the size and number of wires to be connected Cautlon Never connect the bare ground wire lo the black or white house wires 8 Place all wires and connectors back into the junction box making sure there are no loose wire conneclors or pare leads Slide canopy up to ceiling and hold in place by turning knurled nut onto hanger loop 9 For fixtures with glass shades only Your glass shade is held in place either by humbscrews or by a spin on ring screwed onto a threaded socket Place glass shade s into holder and tighten thumbscrews ot Spin ring onto socket 10 Lamp fixture with proper size bulbs n accordance with the watlage label found on the fixture ay White House Wire House Ground Wire Identified Fixture Wire Z Fixlure Ground Wire a Green Ground i Screw Mounting Strap Canopy N onam ees 4 Knurled Nut Hanger Loop me Chain __ ff Fixture Loop MOUNTING AND WIRING INSTRUCTIONS 1 Turn machine screws provided into mounting strap using the threaded holes in the Mounting strap that align with the holes in the canopy 2 Fasten mounting strap to junction box with machine screws found in junction box The mounting strap must be used to provide proper grounding of fixture 3 Pull lea
3. ds down out of junction box for easier wiring Connect the IDENTIFIED lead whitez tinned or ribbed if both conductors are the same color feel for the ribbed edge that runs the entire tength of one side to the WHITE house wire Connect the UNIDENTIFIED lead to the BLACK house wire Turn the green ground screw into the hole in the mounting strap and wrap the bare ground wire around screw one full turn and tighten screw Connect remaining end of bare wire to the house ground wire bare If the junction box itself is metal and is already 4 Place all wir s and connectors back into junction box making sure there are no loose wire nuts or bare leads Place canopy up against ceiling allowing the machine Screws to protrude through the two canopy holes Be care ful not to pinch any wires between the canopy and the ceiling 5 Turn ballnuts onto machine screws until can against Ceiling opy is firmly 6 Lamp fixture with proper size bulbs in accordance with the wattage label found on the fixture grounded attachment to the green screw only is sufficient Junction Always use wire connectors that are UL approved for the Box size and number of wires to be connected White Caution Never connect the bare ground wire to the Black House Wire black or white house wires House Wire __ Identified Fixture Wire Wire Connectors Unidentified Fixture Wire Cag amp snes Mounting rl Strap M achine Screws supplied with
4. fiture House pas 8 SH Ground Wire mu Bail Nuts
5. pple to leave about 3 8 pro ruding through canopy Remove canopy and lightly lock nipple In place by turning hex nut up against mounting strap 3 Assemble one end of chain to fixture loop by opening chaln fink end clasing It around loop NOTE Never twist chaln link to open Chain link must be opened In a C shape 4 Weave the two conductor cord and bare ground wite through the chain about every third lirik Slide knurled nut down chain Slide canopy down chain 3 5 Adjust chain length and wire lead length at this time for _ desired hanging height of fixture Leave at least 12 of leads beyond end of chain 6 Open last chain link then lift chain and fixture up to ceil ing and hook open link through hanger loop Close chain link 7 Insert wire leads through hole in hanger foop and nipple Junction Box N Wire Connectors PO ede Black House Wire Fixture Wire Machine Screws AT a Sa lound ii function bor EL E Hex Nut 3 3 a into junction box Pull leads down out of junction box lor easier wiring Connect the IDENTIFIED lead while linned or ribbed if boli conductors are he saine color feel lor the ribbed edge that runs the entire length of one side to the WHITE house wire Connect the UNIDENTIFIED lead to the BLACK hwuse wire Turn the grean ground screw inlo the hole in the mounting strap and wrap the bare ground wire around screw one full turn and tighten screw Connect femaining en
Download Pdf Manuals
Related Search