Triarch 31401-38 User's Manual
Contents
1. 31401 38 S nue S iron wasner Fixture arm nut iron wasner fixture arm nut pice nut nut secure diffuser fiusn pan ee nicole G Check ring t wasner H Gloss wash r nut Jj giass I K glass washer L nut M bottom coo O N finia Assembly instruction for 31401 38 1 connect fixture arm B with flush pan C 2 Install fixture loop A to fixture B for vendant only 3 Use the icck up 2ut D to connet with Scure 8 and loop A 4 Adjust arms to space evenly 5 Install lignt bulbs not provided 6 Secure glass J with center pipe E nippie F check ring G glass Weczer ED ut D giess washer X 2ut L sottem cap M and Snial TD 7 Connect electrical wires at juzction box end secure crossbar nipple and canopy loop Assembly Instruction for the fixture with safety cable NOTE Fixtures weighing over50 lbs must be supported independently of the outlet bos 1 Turn off power 2 Supply wires shall cuter the outlet box through any knockout except the top center knockout 3 Fixture is to be mounted by a steel pipe approxtmutely 3 4 of 3 8 18NPSN threads at buttom Not Supplied Position pipe so that approximately 1 2 of thread protrudes into outlet box Attach pipe to a Structural Bridging structural bridging member of sufficient strength to support at least 4 times Member the fixture weigh 4 Thread pipe coupling onto protruding2. wires should be pre dent sicure wire connectors with UL Listed electrical tape FINAL ASSEMBLY L spiead the electrical splices sa that the black wires are on one side of the outlet box amd the white wires are on the other side 2 place the fixture against the mounting surface allowing the machine serews to pass tli fares eeure with acom nut provided 3 dn ti ghi Bulbs Do not exceed recommended wattage 4 Restore electricity and cheek the operation of your new light ing fixture
3. inside outlet box 5 Thread hex nut onto threaded pipe Screw threaded pipe into pipe coupling Secure in place by tightening hex out against pipe coupling and Clamps tightening allen head scerw 6 Thread hexnut Ship on ground wire and thread a second hex nut onto threaded pipe 7 Coanect screw collar loop without threaded ring to threaded pipe 8 Pass canopy over screw collar loop Approximately one half of the screw collar loop exterior thread should be exposed Adjust loop as required Remove canopy and tighten hex nut against screw collar loop Tighten second hex nut against first to hold ground wire in place 9 Attach chain to fixture not shown 10 Slip threaded ring then canopy onto chain 11 Attach chain with fixturc conncctcd to bottom of screw collar loop 12 Weave silver support cable up chain and exit through top holc in side of pipe coupling Slip cable through top existing opening or drill 3 16 dia Hole near center of outlet box Wrap cable around structural member described in step 3 Cable must be pulled tanul to evenly distribute fixture weight between cable and chain Secure cable with 2 clamps Allen Head Screw provided 13 Weave both fixture wires and copper ground wire up chain and cxit through top hole inside of pipe coupling ER 14 Connect fixture ground wire and ground wire attached to threaded pipe Ground Wire to outlet box ground wire with wire connector not provided Never connect ground wire to black or
4. move the old fixture Expose supply wi ton the outlet box machine screws into the opposite side of the crnss bar so that screws me facing the downward direction as illus trated in Figure 1 3 Fasten the crossbar to the outlet box using the two screws supplied with the outlet box 4 conneet the grounding wite green or bare copper fom the supply eireuit to grounding wire of vile wires to the green pounding attachment serew the fixture green or bare copper and att provided on the erossbar 5 Make Electrical connections ELECTRICAL CONNECTIONS AS ILLUSTRATED IN FIGURE 1 WARNING Risk of fire Most dwellings built hefore 1985 have supply wire rated 60 C consult a qualified electrician before installing connect the mhdtt Rire s or the ribbed wires from the fixture to the white wire of the supply vironit connect the black wire s af the smooth side of wies from the fixture to the black wire of the supply eirenit Connect the green of bare eoppor colored wire to the grounding conductor of the supply circuit If your fixture is supplied with an spt cord same color each side connect the half of the spt cord that is ribbed surface to the wire wire of the supply eirenit connect the smooth half of hte w the half with markings to the black wire of the supply circuit Use Ul Listed wire connectors su etable for the size type and number of conductors No loose strands or lonse
5. on titled ELECTRICAL CONNECTIONS If you fee you do not yourself Wiring handbook or have your fixture installed by a qualified Licensed electrician ve electrical wiring experience refer to a do it GENERAL 1 To ensure the success of the installation be sure to read these instructions and review the dja grams thoroughly before beginning 2 ALL electrical connections must be in accord es or the National ice with local cedes or Electrical code If you are unfamiliar with methods of installing electrical wiring s services af a licensed electrician 3 These fixtures are intended ta he mounted to a 4 x2 1 8 deep metal octagon bax The box must be directly supported by the building structure 4 Before starting the installation disconnect the power hy turning off the circuit breaker of by re moving the fuse at the fuse box Turning the power off using the light switch is not sufficient to prevent electrical shock to cov NOTE The important safeguards and instrurtions appearing in this manual are not me er all possible conditions and situations that may occur It must be understood that common sense caution and care are factare which cannot be built into any product These factors must he supplied hy the person s caring for installing and operating the fixture PERPARE TRE FIXTURE NOTE FIRST TURN OFF THE ELECTRICITY 1 1 you are replacing an existing fixture disconnect and re
6. power supply wires eee Make wire connectings connectors not provided Reference chart below Threaded Pipe T for correct conncctions and wire accordingly Support Cable Outlet Box Pipe Coupling Hexnut Connect Black or Connect Black or Red Supply Wire to White Supply Wire to White Screw Collar Loop Black Parallel cord square amp ridged Parallel cord round amp smooth Clear Brown Gold or Clear Brown Gold or Black without tracer Black without tracer Insulated wire other than green with copper conductor Insulated wire other than green with sliver conductor Notes When parallel SPTI amp SPTIII are used The Neutral wire is square shaped or ridged and the other wire Will be roundin shape or smooth sce us Chain Warning Consult a qualifie Electrician for installation EN Light loop OUTLET BOX GROUND wRE GROUND BARE WIRE gt BLACK WHITE NUT OUTLET BOX GROUND WIRE GROUND _ T BARE WIRE ELITR WHITE NUT U NUT OUTLET BOX GROUND WIRE GROUND BARE WIRE WHITE OUTLET BOX GROUND WIRE GROUND BARE WIRE WHITE lt _ OUTLET BOX GROUND WIRE READ AND SAVE THESE INSTRUCTIONS INSTALLATION OPERATION INSTRUCTJONS CAUTION Before assembling your Lighting fixture refer to the secti
Download Pdf Manuals
Related Search