Transition Networks MGE-PSW-SX-01 User's Manual
Contents
1. 5 M GE PSW xX 0 Installation Installation Continued Copper and fiber ports Connect the fiber cable The illustration below shows the front panel of the M GE PSW xX 01 media Full duplex always ON is on the fiber side only therefore the 512 Bit Rule does not converters apply The cable lengths are constrained by the cable requirement 1 Locate or build IEEE 803 2 compliant 1000Base X fiber cable with male two stranded TX to RX connectors installed at both ends 2 Connect the fiber cable to the M GE PSW xX 01 media converters as follows Front Panel TP Link Active Fiber Link Activity e Connect the male TX cable connector to the female TX port e Connect the male RX cable connector to the female RX port 3 Connect the fiber cable to the other device another media converter hub etc as follows e Connect the male TX cable connector to the female RX port e Connect the male RX cable connector to the female TX port Copper Port Fiber Port Power ON LED Connect fiber cable Connect fiber cable to media converter to other device as shown media converter hub etc as shown a es 4 TX Electrostatic Discharge ESD Always observe the following ESD precautions when installing or handing the M GE PSW xX 01 media converter e Do not remove the converter from its protective packaging until you are ready to install it e Wear an ESD wrist grounding s2. lectriques il appartiendra alors l utilsateur de prende les measures sp cifiques appropri es In accordance with European Union Directive 2002 96 EC of the European Parliament and of the Council of 27 January 2003 Transition Networks will accept post usage returns of this product for proper disposal The contact information for this activity can be found in the Contact Us portion of this E ocument CAUTION RJ connectors are NOT INTENDED FOR CONNECTION TO THE Fa PUBLIC TELEPHONE NETWORK Failure to observe this caution could result 7 in damage to the public telephone network Der Anschluss dieses Ger tes an ein offentlickes Telekommunikationsnetz in den EG Mitgliedstaaten verst sst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91 263 EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten ber Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformitat 14 Tech Support 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat 5 M GE PSW xX 0 Trademark Notice All trademarks and registered trademarks are the property of their respective owners Copyright Restrictions 2001 2005 Transition Networks All rights reserved No part of this work may be reproduced or used in any form or by any means graphic electronic or mechanical without writ
3. dB 1310 nm single mode min 9 5 dBm max 3 0 dBm min 20 0 dBm max 3 0 dBm 10 5 dB 1310TX 1550RX nm single mode 1550TX 1310RX nm single mode min 8 0 dBm max 3 0 dBm min 21 0 dBm max 3 0 dBm 13 dB JEC 825 CDRH standards and comply with 21 CFR1040 10 and 21CFR1040 11 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours Cable Specifications Continued Copper cable Categories 5 and 5e minimum requirement Gauge 24 to 22 AWG Attenuation 22 0 dB 100m 100 MHz Maximum Cable Distance 100 meters e Straight through or crossover twisted pair cable may be used e Shielded STP or unshielded UTP twisted pair cable may be used e Pins 1 amp 2 and 3 amp 6 are the two active pairs in an Ethernet network e All four pairs are used in a gigabit Ethernet network e Use only dedicated wire pairs for the active pins e g blue white amp white blue orange white amp white orange etc e Do not use flat or silver satin wire Straight Through Cable Crossover Cable 1 1 1 1 Twisted Pair 1 2 2 Twisted Pair 1 2 2 Twisted Pair 2 3 3 Twisted Pair 2 3 3 e 6 CAT5e Gigbit Ethernet Straight Through Cable Twisted Pair 1 Twisted Pair 2 Twisted Pair 3 Twisted Pair 4 techsupport transition com Click the Transition Now link for a live Web chat M GE PSW xX 0 Technical Specifications For use with Transition Networks Model M GE PSW xX 0
4. www transition com and click the Transition Now link Web Based Seminars Transition Networks provides seminars via live web based training Log onto www transition com and click the Learning Center link E Mail Ask a question anytime by sending an e mail to our technical support staff techsupport transition com Address Transition Networks 10900 Red Circle Drive Minnetonka MN 55343 U S A telephone 952 941 7600 toll free 800 526 9267 fax 952 941 2322 TRANSITION Declaration of Conformity Ne NETWORKS Name of Mfg Transition Networks 10900 Red Circle Drive MinnetonkaMN 55343 U S A Model M GE PSW xX 01 Series Media Converters Part Number s M GE PSW LX 01 M GE PSW SX 01 M GE PSW LX 01 100 M GE PSW LX 01 101 Regulation EMC Directive 89 336 EEC Purpose To declare that the M GE PSW xX 01 to which this declaration refers is in conformity with the following standards EN 55022 1994 A1 1995 A2 1997 EN 55024 1998 A1 2001 A2 2003 I the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s at Sark ete a A February 2009 Stephen Anderson Vice President of Engineering Date Compliance Information CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harm
5. 1 converters Technical Specifications Continued Copper based media ports e g Twisted Pair TP Ethernet USB RS232 RS422 RS485 DS1 DS3 Video Coax etc are intended to be connected to intra building Standards IEEE 802 3 2000 inside plant link segments that are not subject to lightening transients or power Data rate 10 Mb s 100 Mb s 1000 Mb s faults Copper based media ports e g Twisted Pair TP Ethernet USB RS232 Dimensions 1 8 W x 3 35 D x 0 85 H 45 7 x 85 1 x 21 6 mm RS422 RS485 DS1 DS3 Video Coax etc are NOT to be connected to inter Weight 3 15 oz 127 5 g approximately Peas outside plant link segments that are subject to lightening transients or power aults MTBF 24 466 hours MIL217F2 V5 0 MIL HDBD 217F n 100 130 hours Bellcore7 V5 0 The product is certified by the manufacturer to comply with DHHS Rule 21 CFR i Subchapter J applicable at the date of manufacture emory e MAC ie Be 8K J WARNING Visible and invisible laser radiation when open Do not stare into the Maximum packet size Power sources Power consumption 1632 bytes untagged 1628 bytes tagged Unit will accept 5 to 28 VDC Barrel connector Wall Mount AC Adapter 400mA at 12VDC The external power supply provided with this product is UL listed by the power supply s manufacturer 262mA 12VDC 3 15 watts beam or view directly with optical instruments Failure to observe this warning could re
6. ally to achieve the best possible mode of operation over a link It broadcasts speed 10 100 1000 Mb s and duplex capabilities full or half to the other device and negotiates the best mode of operation Auto Negotiation allows quick and easy installation because the optimal link is established automatically Power ON LED LED states are as follows In a scenario where an auto negotiation device is linked to a non negotiating device Fiber Link Act LED the negotiating device via parallel detection recognizes the speed of the second Green ON Link fiber device then establishes the best operating speed 0 100 100Mbs at half duplex AutoCross Flashing Activity The AutoCross feature allows using either straight through MDI or crossover MDI X copper cables when connecting to 10Base T or 100Base TX devices TP Link Act LED AutoCross determines the characteristics of the connection and automatically Green ON Link copper configures the device to link up regardless of the copper cable configuration MDI Flashing Activity or MDI X Power LED Link Pass Through Green ON Connected to power The Link Pass Through feature illustrated below allows the media converter to monitor both the fiber and copper RX receive ports for loss of signal In the event of an RX signal loss 1 the media converter will automatically disable the TX transmit signal 2 thus passing through the link loss 3 The far end device is auto
7. faults Copper based media ports e g Twisted Pair TP Ethernet USB RS232 RS422 RS485 DS1 DS3 Video Coax etc are NOT to be connected to inter building outside plant link segments that are subject to lightening transients or power faults Failure to observe this caution could result in damage to equipment Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours the AC outlet e Is the power adapter properly installed in the media converter and in the outlet e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e Proceed to step 2 Note the following e Asa link pass through device both copper and fiber cables must be installed before the LEDs will light 2 Are the TX and FX Link ACT LEDs illuminated on the RJ 45 port NO e Check the copper cables for proper connection e Check the fiber cables for proper connection e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 techsupport transition com Click the Transition Now link for a live Web chat 13 M GE PSW xxX 0 Contact Us Technical Support Technical support is available 24 hours a day US and Canada 1 800 260 1312 International 00 1 952 941 7600 Transition Now Chat live via the Web with Transition Networks Technical Support Log onto
8. ful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense Canadian Regulations This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la Class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada European Regulations Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Achtung Dieses ist ein Ger t der Funkstorgrenzwertklasse A In Wohnbereichen k nnen bei Betrieb dieses Ger tes Rundfunkst rungen auftreten In diesem Fall ist der Benutzer f r Gegenma nahmen verantwortlich Attention Ceci est un produit de Classe A Dans un environment domestique ce produit risque de cr er des interf rences radio
9. matically notified of the link loss 4 which prevents the loss of valuable data unknowingly transmitted over an invalid link media converter A media converter B disables the fiber TX link loses the fiber RX link Near End Media Media Far End Device 7 Converter A Converter 7 Device original fault media converter B on the copper link disables the copper link Note Both copper and fiber cables must be installed before the LEDs will light 6 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat 7 M GE PSW xX 0 Operation Continued Operation Continued Product features continued Product features continued Automatic link restoration The media converter will automatically re establish the link when connected to a switch if the link is lost even with Auto Negotiation and Link Pass through both directions enabled Full duplex flow control In a full duplex network maximum cable lengths are determined by the type of cables used see front cover and cable specifications section The 512 Bit Rule does not apply in a full duplex network Note Full duplex is ON permanently for the fiber port only Half duplex flow control 5 2 Bit Rule In a half duplex network the maximum cable lengths are determined by the round trip delay limitations of each Fast Ethernet collision domain A colli
10. nt the M GE PSW xX 01 media converters extend network distances to the physical cable limitations imposed by the selected twisted pair copper fiber cables Rate conversion The M GE PSW xX 01 media converters allow the following connections e 10Mb s devices on a 10Base T legacy copper network to 1000Mb s devices on a 1000Base SX LX Gigabit Ethernet fiber network e 100Mb s devices on a 100Base T legacy copper network to 1000Mb s devices on a 1000Base SX LX Gigabit Ethernet fiber network Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat M GE PSW xX 0 Cable Specifications The physical characteristics must meet or exceed IEEE 802 3 specifications Fiber cable Bit Error Rate single mode fiber recommended Multimode fiber recommended Multimode fiber optional M GE PSW SX 01 Fiber Optic Transmitter Power Fiber Optic Receiver Sensitivity Link Budget M GE PSW LX 01 Fiber optic Transmitter Power Fiber optic Receiver Sensitivity Link Budget M GE PSW LX 01 100 M GE PSW LX 01 101 Fiber optic Transmitter Power Fiber optic Receiver Sensitivity Link Budget The fiber optic transmitters on this device meet Class I Laser safety requirements per lt 10 9 9 um 62 5 125 um 100 140 85 140 50 125 um 850nm multimode min 10 0 dBm max 4 0 dBm min 17 0 dBm max 0 0 dBm 7 0
11. sion domain is the longest path between any two terminal devices e g a terminal switch or router The 512 Bit Rule determines the maximum length of cable permitted by calculating the round trip delay in bit times BT of a particular collision domain If the result is less than or equal to 512 BT the path is good For more information on the 512 Bit Rule see the white paper titled Collision Domains on the Transition Networks website at www transition com Back pressure Back pressure is used in half duplex mode It ensures the retransmission of incoming packets when a port using half duplex is temporarily unable to receive incoming frames Flow control The process of adjusting the flow of data from one device to another ensures that the receiving device can handle all the incoming data This is particularly important where the sending device is capable of transmitting data much faster than the receiving device can accept it Distance extension The M GE PSW xX 01 media converters can segment one 1 10Base T copper Ethernet 100Base T copper fast Ethernet or 1000Base T copper Gigabit Ethernet and one 1 1000 Base X fiber Fast Ethernet collision domain In a half duplex Ethernet or Fast Ethernet environment the M GE PSW xX 01 media converters extend network distances by segmenting collision domains so that the 512 Bit Rule applies separately to each collision domain In a full duplex Ethernet or Fast Ethernet environme
12. sult in an eye injury or blindness WARNING Use of controls adjustments or the performance of procedures other than those specified herein could result in hazardous radiation exposure The information in this user s guide is subject to change For the most up to date information view the user s guide on line at www transition com Troubleshooting If the media converter fails isolate and correct the failure by determining the answers Environment Tmra 0 C to 50 C 32 F to 122 F to the following questions and then taking the indicated action Storage Temp 25 C to 65 C 13 F to 1 see l Is the power LED illuminated and did the TX and FX LEDs turn ON then turn Humidity 5 to 95 non condensing OFF Altitude 0 to 10 000 feet NO Warranty Lifetime Is the power adapter the proper type of voltage and cycle frequency for MTBF is estimated using the predictability method This method is based on MIL 217F at 25 C ambient temperature typical enclosure heat rise of 10 C with nominal operating conditions and parameters Installation and configuration specific MTBF estimates are available upon request Contact Technical Support Manufacturers rated ambient temperature CAUTION Copper based media ports e g Twisted Pair TP Ethernet USB RS232 RS422 RS485 DS1 DS3 Video Coax etc are intended to be connected to intra building inside plant link segments that are not subject to lightening transients or power
13. ten permission from Transition Networks 16 Printed in the U S A 33398 B
14. trap before handling any module or component If you do not have a wrist strap maintain grounded contact with the system unit EONS kout any Pec CUne regure BaN protection Note With AutoCross permanently enabled the link LED only lights when a valid end to end connection is made 2 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours techsupport transition com Click the Transition Now link for a live Web chat 3 M GE PSW xX 0 Installation Continued Connect the twisted pair copper cable The AutoCross feature allows either MDI straight through or MDI X crossover cable connections to be configured automatically according to network conditions 1 Locate or build IEEE 803 2 compliant 10 100 1000Base T cables with RJ 45 connectors installed at both ends 2 Connect the RJ 45 connector at one end of the cable to the RJ 45 port on the M GE PSW xX 01 media converter 3 Connect the RJ 45 connector at the other end of the cable to the RJ 45 port on the other device switch workstation etc al RJ 45 port RJ 45 port on the media on the other device converter switch work station etc Note With AutoCross permanently enabled the link LED only lights when a valid end to end connection is made 4 Tech Support 1 800 260 1312 International 00 1 952 941 7600 24 hours Installation Continued Powering the media converter The M GE PSW xX 01 media converter is po
15. wered by using a DC power adapter through the barrel connector on its rear panel as shown below Back Panel Barrel Connector j 5 28 VDC S M GE PSW xX 01 Back Panel Power Power adapter AC power 1 Connect the barrel connector of the power adapter to the media converter s power port located on the back panel of the media converter 2 Connect the power adapter plug to AC power Verify that the media converter is powered up by observing the illuminated LED power indicator light on the front panel DC power Consult the user s guide for the Transition Networks SPS 1872 SA DC external power supply for powering the media converter techsupport transition com Click the Transition Now link for a live Web chat M GE PSW xX 0 Operation Operation Continued Status LEDs Product features Use the LEDs to monitor the status of the media converter Congestion reduction bank Panel The M GE PSW xX 01 media converters do not forward collision signals or error packets from one collision domain to another which results in improvements in TP Link Act LED baseline network performance In addition the media converter filters packets destined for local devices which reduces network congestion Fiber Link Act LED Auto Negotiation The Auto Negotiation feature is ON permanently for the M GE PSW xX 01 media converters Auto Negotiation allows the media converter to configure itself automatic
16. z TRANSITION User s Guide M GE PSW SX 01 M GE PSW LX 01 Stand Alone Media Converters e Copper to Fiber e 10 100 1000Base T to 1000Base X The miniature plug and play M GE PSW xX 01 2 port Ethernet Fast Ethernet bridging media converters allow integrating fiber optic cable to 10 100 1000 Unshielded Twisted Pair UTP environments while providing a space saving alternative to traditional sized media converters M GE PSW xX 01 Auto Negotiation AutoCross Link Pass Through Part Number Copper Port Fiber Optic Port 10 100 1000Base T 1000Base FX SC M GE PSW SX 01 RJ 45 SX 850 nm multimode 62 5 125 100 m 328 ft 200m 722 ft 50 125 550m 1 805 ft M GE PSW LX 01 RJ 45 LX 1310 nm single mode 100 m 328 ft 10 km 2 1 miles M GE PSW LX 01 RJ 45 LX 1310TX 1550RX nm single mode 100 100 m 328 ft 20 km 12 4 miles M GE PSW LX 01 RJ 45 LX 1550TX 1310RX nm single mode 101 100 m 328 ft 20 km 12 4 miles Typical maximum cable distance actual distance is dependent upon the physical characteristics of the network M GE PSW LX 01 100 and M GE PSW LX 01 101 are single stand models and are sold in pairs INStA1AtION acc noe besenerae soe ges 2 Operation 2 2400 neiaa 6 Cable Specifications 10 Technical Specifications 12 Troubleshooting 13 Comat US aceeteeresenteseee 14 Declaration of Conformity 14 Compliance Information
Download Pdf Manuals
Related Search