Transition Networks CPSMP-140 User's Manual
Contents
1. 4 Handle Replace the Power Supply Module 6 Replace the Fuse 8 Fuse Technical Specifications 10 on the circuit boara Troubleshooting 11 Contacts me piada prei nese 11 External Power Connectors Compliance Information 12 CPSMP 130 amp CPSMP 140 READ AND FOLLOW ALL WARNING NOTICES amp INSTRUCTIONS MARKED ON THE PRODUCT OR INCLUDED IN THE MANUAL CAUTION All installation and service must be performed by qualified service personnel CAUTION Wear a grounding device and observe electrostatic discharge precautions when installing or servicing the power supply module Failure to observe this caution could result in damage to and subsequent failure of the power supply module The Power Supply Module in the 13 Slot Chassis CPSMP 130 Power Supply 48 VDC The CPSMP 130 power supply module may replace an existing 48 VDC power supply or be installed in the second installation slot see drawing below of the PointSystem 13 slot chassis to become the optional redundant power supply DC Power Second Supply Installation Slot CPSMP 140 Power Supply 24 Volt The CPSMP 140 power supply module may replace an existing 24 VDC power supply or be installed in the second installation slot see drawing above of the PointSystem 13 slot chassis to become the optional redundant power supply NOTE Both the CPSMP 130 and the CPSMP 140 DC2. Carefully slide the power supply module into the installation slot aligning the module with the installation guides A 4 Ensure that the power supply module is firmly seated inside the chassis Rotate the attached panel fastener screw clockwise to secure the power supply module to the chassis techsupport transition com Click the Transition Now link for a live Web chat 3 CPSMP 130 amp CPSMP 140 Connect to External Power CAUTION Ensure that external power source is NOT powered and that the On Off switch on the power supply module is set to 0 when connecting to the external power source Failure to observe this caution could result in damage to and subsequent failure of the power supply module 48 VDC power supply This product is intended to be used in a restricted access location Proper earthing grounding is required to ensure safe operation and to comply with customer installation requirements and local electrical codes Prior to installation use a voltmeter ohmmeter to check the wiring for the presence of earth ground A readily accessible disconnect device as part of the building installation shall be incorporated into the fixed wiring The disconnect device a 48 VDC 15 or 20A circuit breaker or switch must be included in the ungrounded supply conductor Overcurrent protection must be a 48 VDC 15 or 20A fuse or circuit breaker 24 VDC Power Supply This product is intended to be used i
3. To declare that the CPSMP 130 and CPSMP 140 to which this declaration refers are in conformity with the following standards EN 55022 1988 A1 2000 Class A FCC Part 15 subpart B UL 1950 I the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s ee ee une 8 2001 Stephen Anderson Vice President of Engineering Date Trademark Notice All trademarks and registered trademarks are the property of their respective owners Copyright Restrictions 2001 2004 Transition Networks All rights reserved No part of this work may be reproduced or used in any form or by any means graphic electronic or mechanical without written permission from Transition Networks Printed in the U S A 33213 B
4. power supply modules may be installed as the redundant power supply in any of the three PointSystem 13 slot chassis e CPSMC1300 100 AC chassis e CPSMC1310 100 48 VDC chassis e CPSMC1320 100 24 VDC chassis For more information see the user s guide for the CPSMC13xx 100 13 slot chassis on line at www transition com 2 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 WARNING Do NOT connect the power supply module to the external power source before installing it into the chassis Failure to observe this caution could result in equipment damage and or personal injury or death Install the Power Supply Module CAUTION Ensure that the power supply module has been disconnected from the external power source and the module s On Off switch has been set to 0 Failure to observe this caution could result in damage to and subsequent failure of the power supply module NOTE The power supply module may be hot swapped i e installed in the chassis while the chassis is in operation provided the module to be installed has been disconnected from its external power source and the module s On Off switch has been set to 0 To install the power supply module into the PointSystem chassis 1 Loosen the screw that secures the protective plate to the chassis and pull the plate away from the chassis 2 Set the On Off switch on the power supply module to 0
5. supply and the module s On Off switch has been set to 0 To replace the fuse in the CPSMP 130 or CPSMP 140 power supply module 1 2 3 6 7 Set the On Off switch on the power supply module to 0 Verify that the external power source is NOT powered Disconnect the positive DC terminal from the external power connector marked Disconnect the negative DC terminal from the external power connector marked Disconnect the ground terminal from the external power connector marked chassis ground Panel Faste Power LED Connectors Rotate the attached panel fastener screw counter clockwise Carefully slide the power supply module out of the chassis a 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 WARNING Do NOT connect the power supply module to the external power source before installing it into the chassis Failure to observe this caution could result in equipment damage and or personal injury or death 8 10 11 12 13 14 15 Remove the four 4 screws that secure the panel to the module see the drawing below and remove the panel from module Remove these four 4 screws to access the fuse The fuse is located inside the power supply module on the circuit board Remove the fuse from the fuse holder Install a same size and rating replacement fuse in the
6. TRANSITION networks User s Guide CPSMP 130 48 VDC Power Supply Module CPSMP 140 24 VDC Power Supply Module 13 Slot PointSystem Accessory The Transition Networks CPSMP 130 power supply is a 48 VDC slide in module that provides optional redundant power to the CPSMC1310 100 13 slot PointSystem chassis and any installed media converter slide in modules and management modules The Transition Networks CPSMP 140 power supply is a 24 VDC slide in module that provides optional redundant power to the CPSMC1320 100 13 slot PointSystem chassis and any installed media converter slide in modules and management modules The figure below illustrates the components of both types of power supplies An On Off switch that when set to I allows the power supply module to supply power to the chassis and any installed modules A panel fastener screw that secures the power supply module to the chassis A power LED indicator A handle for installing and removing the power supply module to from the chassis A fuse installed on the circuit board inside the power supply module s housing A set of three 3 external power connectors that distribute power from an external DC outlet to a chassis ground connector a positive connector and a negative connector on the power supply module On Off Switch G Panel Fastener Screw stall the Power Supply Module 3 Power LED Connect to External Power
7. ct Us Technical Support Technical support is available 24 hours a day US and Canada 1 800 260 1312 International 00 1 952 941 7600 Transition Now Chat live via the Web with Transition Networks Technical Support Log onto www transition com and click the Transition Now link Web Based Seminars Transition Networks provides seminars via live web based training Log onto www transition com and click the Learning Center link E Mail Ask a question anytime by sending an e mail to our technical support staff techsupport transition com Address Transition Networks 6475 City West Parkway Minneapolis MN 55344 USA telephone 952 941 7600 toll free 800 526 9267 fax 952 941 2322 techsupport transition com Click the Transition Now link for a live Web chat 11 Compliance Information UL Listed C UL Listed Canada CE Mark CISPR22 EN55022 Class A FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interfer
8. ence in which case the user will be required to correct the interference at the user s own expense Canadian Regulations This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la Class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada European Regulations Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Achtung Dieses ist ein Ger t der Funkst rgrenzwertklasse A In Wohnbereichen k nnen bei Betrieb dieses Ger tes Rundfunkstdrungen auftreten in weichen Fallen der Benutzer fur entsprechende Gegenma nahmen werantwortlich ist Attention Ceci est un produit de Classe A Dans un environment domestique ce produit risque de cr er des interf rences radio lectriques il appartiendra alors a l utilsateur de prende les measures sp cifiques appropri es CRANSTTION Declaration of Conformity Name of Mfg Transition Networks 6475 City West Parkway Minneapolis MN 55344 USA Model Redundant Power Supply Part Number s CPSMP 130 CPSMP 140 Regulation EMC Directive 89 336 EEC Purpose
9. fuse holder Replace the panel to the power supply module and secure it in place with the four 4 screws Carefully slide the power supply module into the installation slot aligning the module with the installation guides Ensure that the power supply module is firmly seated inside the chassis Rotate the attached panel fastener screw clockwise to secure the power supply module to the chassis See the Connect to External Power section page 5 for instructions on re connecting the power supply module to the external power source techsupport transition com Click the Transition Now link for a live Web chat 9 CPSMP 130 amp CPSMP 140 Technical Specification For use with Transition Networks model CPSMP 130 or CPSMP 140 or equivalent Standards UL Listed FCC amp CISPR Class A CE Mark Dimensions 3 4 x 2 5 x 11 0 86 mm x 64 mm x 279 mm Weight 1 8 Ib 0 8 kg approximate CPSMP 130 Power Input 48VDC 38 to 58VDC 2 63Amp typical for a fully loaded chassis Power Output 12 VDC 12 5 Amp maximum CPSMP 140 Power Input 24VDC 20 to 31VDC 4 83 Amp typical for a fully loaded chassis Power Output 12 VDC 8 3 Amp maximum Fuse 6 3Amp 250V MTBF 520 441 hours MIL217F2 V5 0 MIL HDBK 217F 1 087 866 hours Bellcore7 V5 0 Environment Tmra O to 50 C 32 to 122 F Storage Temp 20 to 85 C 4 to 185 F Humidity 10 to 90 non condensing Altitude 0 to 10 000 feet War
10. n a restricted access location Proper earthing grounding is required to ensure safe operation and to comply with customer installation requirements and local electrical codes Prior to installation use a voltmeter ohmmeter to check the wiring for the presence of earth ground A readily accessible disconnect device as part of the building installation shall be incorporated into the fixed wiring The disconnect device a 24 VDC 15 or 20A circuit breaker or switch must be included in the ungrounded supply conductor Overcurrent protection must be a 24 VDC 15 or 20A fuse or circuit breaker 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 Connect to External Power Continued To power the CPSMP 130 or the CPSMP 140 power supply module 1 2 3 Set the On Off switch on the power supply module to 0 Verify that the external power source is NOT powered Connect the positive terminal to the external power connector marked Turn the terminal screw clockwise to secure Connect the negative terminal to the external power connector marked Turn the terminal screw clockwise to secure Connect the ground terminal to the external power connector marked chassis ground Turn the terminal screw clockwise to secure Set the power supply module power switch to I Verify that the power supply module is powered by observing the illuminated power LED On Off Panel Fa
11. ranty Lifetime Manufacturer s rated ambient temperature Tmra range for these power supply modules depend on the physical characteristics and the installation configuration of the Transition Networks PointSystem chassis in which this slide in module will be installed For the most up to date information on the CPSMP 130 and CPSMP 140 power supply modules view the user s guide on line at www transition com 10 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 Troubleshooting If the power supply module fails isolate and correct the failure by determining the answers to the following questions and then taking the indicated action 1 Is the power LED on the power supply module illuminated NO e Is the power supply module inserted properly into the chassis e Is the power supply module properly connected to the external power source e Does the external power source provide power e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e Proceed to step 2 2 Is the fuse on the power supply intact NO e CAUTION See the Replacing the Fuse section page 8 in this user s guide for the proper method for replacing the fuse to the power supply module e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 YES e Contact Technical Support US Canada 1 800 260 1312 International 00 1 952 941 7600 Conta
12. round Rotate the attached panel fastener screw counter clockwise Panel F Power LED On Off astener Screw G Connectors Carefully slide the power eR to be replaced out of the chassis 24 hour Technical Support 1 800 260 1312 International 00 1 952 941 7600 Replace the Power Supply Module Continued 8 Carefully slide the replacement power supply module into the installation slot aligning the module with the installation guides 9 Ensure that the power supply module is firmly seated inside the chassis 10 Rotate the attached panel fastener screw clockwise to secure the power supply module to the chassis 11 See the Connect to External Power section page 5 for instructions on re connecting the power supply module to the external power source techsupport transition com Click the Transition Now link for a live Web chat 7 CPSMP 130 amp CPSMP 140 Replace the Fuse CAUTION Ensure that the power supply module has been disconnected from the external power source and the module s On Off switch has been set to 0 Failure to observe this caution could result in damage to and subsequent failure of the power supply module NOTE The power supply module may be hot swapped i e serviced while the chassis is in operation provided the module to be serviced has been disconnected from its external power
13. stener Scre Switch Power LED External Power Connectors techsupport transition com Click the Transition Now link for a live Web chat 5 CPSMP 130 amp CPSMP 140 WARNING Do NOT connect the power supply module to the external power source before installing it into the chassis Failure to observe this caution could result in equipment damage and or personal injury or death Replace the Power Supply Module CAUTION Ensure that the power supply module has been disconnected from the external power source and the module s On Off switch has been set to 0 Failure to observe this caution could result in damage to and subsequent failure of the power supply module NOTE The power supply module may be hot swapped i e replaced while the chassis is in operation provided the module to be replaced has been disconnected from its external power source and the module s On Off switch has been set to 0 To replace the CPSMP 130 or the CPSMP 140 power supply module 1 2 a Set the On Off switch on the power supply module to 0 Verify that the external power source is NOT powered Disconnect the positive terminal from the external power connector marked Disconnect the negative terminal from the external power connector marked Disconnect the ground terminal from the external power connector marked chassis g
Download Pdf Manuals
Related Search