Home

TP-Link TL-SL5428E V2 CLI Reference Guide

1. Link Types There are three Link Types for the ports Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Specify the Link Type of Fast Ethernet port 3 as trunk TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if switchport mode trunk switchport access vlan Description The switchport access vlan command is used to add the desired Access port to IEEE 802 1Q VLAN or to remove a port from the corresponding VLAN Syntax switchport access vlan vian id no switchport access vlan 21 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Parameter vlan id Specify IEEE 802 1Q VLAN ID ranging from 2 to 4094 Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure Fast Ethernet port 3 whose link type is access to VLAN 2 TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if switchport access vlan 2 switchport trunk allowed vian Description The switchport trunk allowed vian command is used to add the desired Trunk port to IEEE 802 1Q VLAN To remove a Trunk port from the corresponding VLAN please use no switchport trunk allowed vlan command Syntax switchport trunk allowed vlan v an list all no switchport trunk a
2. Create a standard IP ACL whose ID is 123 TL SL5428E config access list create 123 mac access list Description The mac access list command is used to create MAC ACL To set the detailed configurations for a specified MAC ACL please use mac access list command to access Mac Access list Configuration Mode To delete the MAC ACL please use no mac access list Syntax mac access list access list num no mac access list access list num 169 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Parameter access list num ACL ID ranging from 0 to 99 Command Mode Global Configuration Mode Example Create a MAC ACL whose ID is 23 TL SL5428E config mac access list 23 access list standard Description The access list standard command is used to add Standard IP ACL rule To delete the corresponding rule please use no access list standard command Standard IP ACLs analyze and process data packets based on a series of match conditions which can be the source IP addresses and destination IP addresses carried in the packets Syntax access list standard acl id rule rule id deny permit sip source ip smask source ip mask dip destination ip dmask destination ip mask tseg time segment frag disable enable no access list standard acl id rule rule id Parameter acl id The desired Standard IP ACL for configuration rule id The rule ID deny The operation to discard packets per
3. Privileged EXEC Mode as 123 in the prompted DOS screen shown in Figure 1 5 TL SL5428E BA 6 0 5 1 BRETT DL EG e BRETT tp link HyperTerminal File Edit View Call Transfer Help Oe 2309 TL SL5428E gt TL SL5428E gt enable TL SL5428E config TL SL5428E config line vty 5 TL SL5428E config line login local lt set login mode TL SL5428E config line exit set password for TL SL5428E config enable password 123 lt entering Privileged EXEC Mode Figure 1 6 Configure login local mode Now you can logon by Telnet in login local mode 1 Make sure the switch and the PC are in the same LAN Click Start Run to open the Run window and type cmd in the prompt Run window as Figure 1 7 and click OK Type the name of a program folder document or Internet resource and Windows will open it for you Open Cancel Browse Figure 1 7 Run Window 2 Open Telnet then type telnet 192 168 0 1 in the command prompt shown as Figure 1 8 and press the Enter button C AWINDOWS system32 cmd exe of x gt Dier 2600 a SET RR Figure 1 8 Connecting to the Switch TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide 3 Type the default user name and password admin admin then press the Enter button so as to enter User EXEC Mode cir Telnet 192 168 0 1 User Access Login Wser admin Password TL SLS428E gt _ Figure 1 9 E
4. TL SL5428E config protocol vian template name TP ether type 2024 29 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT protocol vlan vlan Description The protocol vlan vlan command is used to create a Protocol based VLAN entry To delete a Protocol based VLAN entry please use no protocol vlan vlan command Syntax protocol vlan vlan vian id template template idx no protocol vlan vlan group idx Parameter vlan id Specify IEEE 802 1Q VLAN ID ranging from 1 4094 template idx The number of the Protocol based VLAN Template You can get the template corresponding to the number by the show protocol vlan template command group idx The number of the Protocol based VLAN entry You can get the Protocol based VLAN entry corresponding to the number by the show protocol vian vlan command Command Mode Global Configuration Mode Example Create Protocol based VLAN 2 and bind it with Protocol based VLAN Template 3 TL SL5428E config protocol vlan vlan 2 template 3 protocol vlan Description The protocol vlan command is used to enable the Protocol based VLAN feature for a specified port To disable the Protocol based VLAN feature of this port please use no protocol vlan command By default the Protocol based VLAN feature of all ports is disabled 30 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Syntax protocol vlan no protocol vlan Command Mode Interface Configuration Mode interface
5. source filter none indicates applying none both indicates applying both 67 TL SL5428E MOCSUCEU MIA EME Eli e BRETT Command Mode Global Configuration Mode Example Modify the hostname as tp link of the entry with the index 1 TL SL5428E config ip source binding index 1 hostname tp link ip dhcp snooping Description The ip dhcp snooping command is used to enable DHCP Snooping function globally To disable DHCP Snooping function globally please use no ip dhcp snooping command DHCP Snooping functions to monitor the process of the Host obtaining the IP address from DHCP server and record the IP address MAC address VLAN and the connected Port number of the Host for automatic binding The switch can also propagate the control information and the network parameters via the Option 82 field to provide more information for the Host Syntax ip dhcp snooping no ip dhcp snooping Command Mode Global Configuration Mode Example Enable the DHCP Snooping function globally TL SL5428E config ip dhcp snooping ip dhcp snooping global Description The ip dhcp snooping global command is configure DHCP Snooping globally To restore to the default value please use no dhcp snooping global command 68 TL SL5428E BA 6 KY LLE a EV Xe DL Eli e BRETT Syntax ip dhcp snooping global global rate global rate dec threshold dec threshold dec rate dec rate no ip dhcp snooping global Parameter gl
6. 157 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TL SL5428E config monitor session 1 source interface fastEthernet 1 0 4 5 1 0 7 rx Delete the Fast Ethernet port 4 in monitor session 1 and its configuration TL SL5428E config no monitor session 1 source interface fastEthernet 1 0 4 rx show monitor session Description The show monitor session command is used to display the configuration of port monitoring Syntax show monitor session session_num Parameter session_num The monitor session number the value of which is 1 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the monitoring configuration of monitor session 1 TL SL5428E config show monitor session 1 158 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 25 Port isolation Commands Port Isolation provides a method of restricting traffic flow to improve the network security by forbidding the port to forward packets to the ports that are not on its forwarding port list port isolation Description The port isolation command is used to configure the forward port list of a port so that this port can only communicate with the ports on its port list To delete the corresponding configuration please use no port isolation command Syntax port isolation fa forward list fa forward list gi forward list gi forward list no port isolation
7. 48 63 TC3 2 Among the priority levels TCO TC3 the bigger value the higher priority Example Map DSCP values 10 12 to TC 2 TL SL5428E config qos queue dscp map 10 12 2 qos queue mode Description The qos queue mode command is used to configure the Schedule Mode To return to the default configuration please use no qos queue mode command When the network is congested the program that many packets complete for resources must be solved usually in the way of queue scheduling The switch will control the forwarding sequence of the packets according to the priority 152 TL SL5428E BA 6 LLE a EME EG e BRETT queues and scheduling algorithms you set On this switch the priority levels are labeled as TCO TC1 TC3 Syntax qos queue mode sp wrr sp wrr equ no qos queue mode Parameter sp Strict Priority Mode In this mode the queue with higher priority will occupy the whole bandwidth Packets in the queue with lower priority are sent only when the queue with higher priority is empty wrr Weight Round Robin Mode In this mode packets in all the queues are sent in order based on the weight value for each queue The weight value ratio of TCO TC1 TC2 and TC3 is 1 2 4 8 sp wrr Strict Priority Weight Round Robin Mode In this mode the switch provides two scheduling groups SP group and WRR group Queues in SP group and WRR group are scheduled strictly based on Strict Priority mode while t
8. cecccecccceeeeeeceeeeeeeceeeeeeeeeeeceeeaeeeeeeeessceaeaeeeeeeeeseeesuneneeseees 136 interface gigabitEthern t A 137 interface range gigabitEthernet oooooooococococccccccconconcnccnnnccconnnnnonnnnnnnoncnnannnnnnnnnnnnnnnnnnnnnnnnnnnno 137 AOS MI EEN 138 SOU EE 139 A seed Egeter ak eee d he bees ebesnaa sad boa cs E be coma sateddevabeedensalaxdevetantiteess 139 mediatype ENEE 140 o 6 0 D coset Rast tees eta ce ec fi eek i toed AR ial ES eared ate E 140 en EEN 141 storm control broadcast cee 141 tel Eeer Ku Le 142 ele eeler Rive E 143 DAanGwidthie e ioc erin A ete EE 143 ege ln 144 le Olne TEEN 144 show interface Counters ttet ttttttEE EEE EAESEEEEEEEE EEES ESEEEEEE EEES EREAEE EEEE EERe rrene 145 show interface description 146 show interface flowcontrol cccceeceeeceeeeeeeeeeeeeeceneaeeeeeeeeeeceneaaeeeeeeeeeeseeccaeeseeeeeeeseeneuaeaees 146 show interface Confiouration tettette tttt tnte Eet tEEE EEES ESEE EE EEES EnE EEEE Ennn 147 Glenn e RE 147 Neen An WEE 148 Chapter 23 QoS COmMMmaNdS ooo in 149 le 149 GOS e 149 COS CO A a e T 150 QOS QUE E COS MA D ii a a ENEE TA EEREN RETE 151 OS queue USC MAP tidad es 151 VIII GOS QUEUE lee EE 152 SHOW COS interface 2 cece ce ceeceeeecece cece eeeeeeeaeeeceeeeceeeaeaeeeceeeeeeeeecceaeaeeeseeeeeeeqeeeaeeeeeesesseeeenaes 153 SNOW QOS Cos map nn eee eee 154 SHOW GOS ISC Marita dida ptas 154 ShOW QOS qQueUC Mode snet iind A e AA AAA a ey 155 SHOW QOS EE 155 C
9. fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the STP function for Fast Ethernet port 2 182 TL SL5428E MOSCA EME EG e BRETT TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if spanning tree spanning tree common config Description The spanning tree common config command is used to configure the parameters of the ports for comparison in the CIST and the common parameters of all instances To return to the default configuration please use no spanning tree common config command CIST Common and Internal Spanning Tree is the spanning tree in a switched network connecting all devices in the network spanning tree common config port priority pri ext cost ext cost int cost int cosf portfast enable disable point to point auto open close no spanning tree common config Parameter pri Port Priority which must be multiple of 16 ranging from 0 to 240 By default the port priority is 128 Port Priority is an important criterion on determining if the port connected to this port will be chosen as the root port In the same condition the port with the highest priority will be chosen as the root port The lower value has the higher priority ext cost External Path Cost which is used to choose the path and calculate the path costs of ports in different MST regions It is an important criterion on determining the root port The lo
10. monitor session source interface command monitor session session_num source interface fastEthernet port list gigabitEthernet port list mode no monitor session session_num source interface fastEthernet port list gigabitEthernet port list mode Parameter Session num The monitor session number the value of which is 1 port list List of monitored port It is multi optional mode The monitor mode There are three options rx tx and both Rx ingress monitoring mode means the incoming packets received by the monitored port will be copied to the monitoring port TX egress monitoring mode indicates the outgoing packets sent by the monitored port will be copied to the monitoring port Both ingress and egress monitoring presents the incoming packets received and the outgoing packets sent by the monitored port will both be copied to the monitoring port Command Mode Global Configuration Mode User Guidelines 1 The monitoring port is corresponding to current interface configuration mode 2 Monitored ports number is not limited but it can t be the monitoring port at the same time 3 Whether the monitoring port and monitored ports are in the same VLAN or not is not demanded strictly 4 The monitoring port and monitored ports cannot be link aggregation member Example Create monitor session 1 then configure Fast Ethernet port 4 5 7 as monitored ports and enable ingress monitoring
11. 3 Windows Messenger Y Paint ES Command Prompt a Windows Movie Maker S i Program Compatibility Wizard A Activate Windows Synchronize OvisLink Wireless Che Utility wi MSN Tour Windows XP 3 Windows Explorer A WordPad IxChariot EN asmax H LogMeTT E Tera Term E Microsoft Office Im Macrovision E TP LINK All Programs ei OvisLink Ag OFF Turn OFF Computer Windows Media Play Paint e e e e e e e e Figure 1 1 OpenHyper Terminal 3 The Connection Description Window will prompt as Figure 1 2 Enter a name into the Name field and click OK TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Connection Description K New Connection Enter a name and choose an icon for the connection Name tp link Mes3zeur Figure 1 2 Connection Description 4 Select the port to connect in Figure 1 3 and click OK Connect To B tp link Enter details for the phone number that you want to dial Country region Area code Phone number Connect using Y Figure 1 3 Select the port to connect 5 Configure the port selected in the step above as the following Figure 1 4 shown Configure Bits per second as 38400 Data bits as 8 Parity as None Stop bits as 1 Flow control as None and then click OK COM1 Properties pes Port Settings Bits per second Data bits 8 Parity None Stop bits Flow contrat Y Restore Default
12. Port Security To return to the default configurations please use no mac address table max mac count command Port Security is to protect the switch from the malicious MAC address attack by limiting the maximum number of the MAC addresses that can be learned on the port The port with Port Security feature enabled will learned the MAC address dynamically When the learned MAC address number reaches the maximum the port will stop learning Therefore the other devices with the MAC address unlearned can not access to the network via this port Syntax mac address table max mac count max number num mode dynamic static permanent status disable enable no mac address table max mac count Parameter num The maximum number of MAC addresses that can be learned on the port It ranges from 0 to 64 By default this value is 64 dynamic static permanent Learn mode for MAC addresses There are three modes including Dynamic mode Static mode and Permanent mode When Dynamic mode is selected the learned MAC address will be deleted automatically after the aging time When Static mode is selected the learned MAC address will be out of the influence of the aging time and can only be deleted manually The learned entries will be cleared after the switch is rebooted When permanent mode is selected the learned MAC address will be out of the 114 TL SLSA7pERIGCEIORRKR EIET DL EG e BRETT influence of th
13. VLAN ID and the Port number together in the condition that you have got the related information of the Hosts in the LAN To delete the IP MAC VID PORT entry from the binding table please use no ip source binding index command Syntax ip source binding hostname ip addr mac addr vlan vlan id interface fastEthernet port gigabitEthernet port none arp detection ip verify source both forced source arp scanning dhcp snooping no ip source binding index dx Parameter hostname The Host Name which contains 20 characters at most ip addr The IP address of the Host mac addr The MAC address of the Host vlan id The VLAN ID needed to be bound ranging from 1 to 4094 port The number of port connected to the Host none arp detection ip verify source both The protect type for the entry arp detection indicates ARP detection ip verify source indicates IP source filter none indicates applying none both indicates applying both forced source The source of the binding entry can be specified as arp scanning or dhcp snooping It is multi optional idx The entry number needed to be deleted You can use the show ip source binding command to get the idx Pay attention that the entry number is the actual number in the binding table which is not display in an arranged order 66 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Co
14. node of the network Syntax ping p_adar n count H count i count Parameter ip_addr The IP address of the destination node for ping test 130 TL SL5428E BA 5 0 5 1 aE TATT DL Eli e BRETT n count The amount of times to send test data during Ping testing It ranges from 1 to 10 By default this value is 4 count The size of the sending data during ping testing It ranges from 1 to 1024 bytes By default this value is 64 i count The interval to send ICMP request packets It ranges from 100 to 1000 milliseconds By default this value is 1000 Command Mode User EXEC Mode and Privileged EXEC Mode Example To test the connectivity between the switch and the network device with the IP 192 168 0 131 please specify the count l as 512 bytes and count i as 1000 milliseconds If there is not any response after 8 times Ping test the connection between the switch and the network device is failed to establish TL SL5428E ping 192 168 0 131 n 8 1 512 tracert Description The tracert command is used to test the connectivity of the gateways during its journey from the source to destination of the test data Syntax tracert ip_addr w waitTime h maxHops Parameter ip_addr The IP address of the destination device waitTime The maximum time for the test data to wait before timeout It ranges from 1 to 10000ms maxHops The maximum number of the route
15. password Interface vian Privileged EXEC Global Configuration Mode Mode VLAN Configuration Mode The following table gives detailed information about the Accessing path Prompt of each mode and how to exit the current mode and access the next mode Mode Accessing Path Prompt Logout or Access the next mode Use the exit command to disconnect the ir Tee Primary mode once it is switch except that the switch is seh connected with the TL SL5428E gt connected through the Console port switch Use the enable command to access Privileged EXEC mode Use the enable Enter the disable or the exit command to Privileged command to enter this TL SL5428E return to User EXEC mode EXEC Mode mode from User EXEC Enter configure command to access mode Global Configuration mode Use the exit or the end command or press Ctrl Z to return to Privileged EXEC mode Use the configure Use the interface fastEthernet Global E Configuration command to enter this gigabitEthernet port or interface range 9 mode from Privileged TL SL5428E config fastEthernet gigabitEthernet port list Mode EXEC mode command to access interface Configuration mode Use the vlan vlan list to access VLAN Configuration mode 11 TL SL5428E MOSCA EME BESANI e BRETT Mode Accessing Path Prompt Logout or Access the next mode Use the interface Use the end command or press Ctrl Z to fastEthernet gigabitE
16. please use no contact info command Syntax contact info contact_info no contact info contact_info Parameter contact_info Contact Information It consists of 32 characters at most It is www tp link com by default Command Mode Global Configuration Mode Example Configure the system contact information as www tp link com TL SL5428E config contact info www tp link com ip management vlan Description The ip management vlan command is used to configure the management VLAN through which you can log on to the switch By default the management VLAN is VLAN1 Syntax ip management vlan vlan id Parameter vlan id VLAN ID ranging from 1 to 4094 Command Mode Global Configuration Mode Example Set the VLAN6 as management VLAN TL SL5428E config ip management vlan 6 125 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT ip address Description The ip address command is used to configure the system IP Address Subnet Mask and Default Gateway To restore to the factory defaults please use no ip address command This command should be configured in the Interface Configuration Mode of the management VLAN Syntax ip address ip addr ip mask gateway no ip address Parameter ip addr The system IP of the switch The default system IP is 192 168 0 1 ip mask The Subnet Mask of the switch The default Subnet Mask is 255 255 255 0 gateway The Default Gateway of the switch By def
17. under Time range Create Configuration Mode To delete the corresponding Holiday Mode time range please use no holiday command Syntax holiday no holiday Command Mode Time range Create Configuration Mode Example Configure the time range tSeg1 into Holiday Mode TL SL5428E config time range tSeg1 TL SL5428E config time range holiday holiday global Description The holiday command is used to define a holiday To delete the corresponding holiday please use no holiday command Syntax holiday name start date start date end date end date no holiday Parameter name The holiday name ranging from 1 to 16 characters start date The start date of the holiday in the format of MM DD for instance 05 01 end date The end date of the holiday in the format of MM DD for instance 05 03 168 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Command Mode Global Configuration Mode Example Define National Day configuring the start date as October 1st and the end date as October 3rd TL SL5428E config holiday nationalday start date 10 01 end date 10 03 access list create Description The access list create command is used to create standard IP ACL and extend IP ACL Syntax access list create access list num Parameter access list num ACL ID ranging from 100 to 299 100 199 must be Standard IP ACL and 200 299 must be Extend IP ACL Command Mode Global Configuration Mode Example
18. 01 2000 The Absolute Mode will be disabled if the start date and end date are both in default value Command Mode Time range Create Configuration Mode Example Configure the time range tSeg1 with time from May 5 2012 to Oct 5 2012 TL SL5428E config time range tSeg1 TL SL5428E config time range absolute start 05 05 2012 end 10 05 2012 periodic Description The periodic command is used to configure the time range into periodic mode To delete the corresponding Periodic Mode time range please use no periodic command Syntax periodic week date week day time slice1 time slice time slice2 time slice time slice3 time slice time slice4 time slice no periodic Parameter week day Periodic Mode in the format of 1 3 6 or daily off day working day 1 3 6 represent Monday Tuesday Wednesday and Saturday daily represents every day off day represents weekend and working day represents working day By default the Periodic Mode is disabled time slice Create the time slice in the format of HH MM HH MM Command Mode Time range Create Configuration Mode Example Configure the time range tSeg1 with time from 8 30 to 12 00 at weekend 167 TL SL5428E BAG 6 0 5 1 WAV EV Xe DL EG e BRETT TL SL5428E config time range tSeg1 TL SL5428E config time range periodic week date off day time slice1 08 30 12 00 holiday Description The holiday command is used to configure the time range into Holiday Mode
19. 4094 Command Mode Global Configuration Mode Example Enable the Voice VLAN function for VLAN 10 TL SL5428E config voice vlan 10 voice vian aging time Description The voice vlan aging time command is used to set the aging time for a voice VLAN To restore to the default aging time for the Voice VLAN please use no voice vlan aging time command By default the aging time is 1440 minutes Syntax voice vlan aging time time 38 TL SL5428E BA 6 0 5 1 a EME EG e M EE ETT IT no voice vlan aging time Parameter time Aging time in minutes to be set for the Voice VLAN lt ranges from 1 to 43200 Command Mode Global Configuration Mode Example Set the aging time for the Voice VLAN as 1 minute TL SL5428E config voice vlan aging time 1 voice vlan priority Description The voice vlan priority command is used to configure the priority for the Voice VLAN To restore to the default priority please use no voice vlan priority command By default the priority value is 6 Syntax voice vlan priority pri no voice vlan priority Parameter pri Priority ranging from 0 to 7 Command Mode Global Configuration Mode Example Configure the priority of the Voice VLAN as 5 TL SL5428E config voice vlan priority 5 39 TL SL5428E BAS KY LLE a EME Eli e BRETT voice vlan mac address Description The voice vlan mac address command is used to create Voice VLAN OUI To delete the specified Vo
20. EE ETT IT logging file flash Description The logging file flash command is used to configure the level and the status of the log file input To restore to the default configuration please use no logging file flash command The log file indicates the flash sector for saving system log The information in the log file will not be lost after the switch is restarted and can be got by the show logging flash command Syntax logging file flash level no logging file flash Parameter level Severity level of the log information output to each channel There are 8 severity levels marked with values 0 7 The smaller value has the higher priority Only the log with the same or smaller severity level value will be output By default it is 2 indicating that the log information marked with 0 2 will be saved in the log buffer Command Mode Global Configuration Mode Example Enable the log file function and set the severity as 7 TL SL5428E config logging file flash 7 clear logging Description The clear logging command is used to clear the information in the log buffer and log file Syntax clear logging buffer flash 100 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Parameter buffer flash The output channels buffer and flash Clear the information of the two channels by default Command Mode Global Configuration Mode Example Clear the information in the log file TL SL5428E config clear
21. Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the system current operating configuration TL SL5428E show running config 134 TL SL5428E BAGS LLE aE TATT DL Eli e BRETT show cable diagnostics interface Description The show cable diagnostics interface command is used to display the cable diagnostics of the connected Ethernet Port which facilitates you to check the connection status of the cable connected to the Switch locate and diagnose the trouble spot of the network Syntax show cable diagnostics interface fastEthernet port gigabitEthernet port Parameter port The number of the port which is selected for Cable test Command Mode Privileged EXEC Mode and Any Configuration Mode Example Show the cable diagnostics of Gigabit Ethernet port 25 TL SL5428E show cable diagnostics interface gigabitEthernet 1 0 25 135 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Chapter 22 Ethernet Configuration Commands Ethernet Configuration Commands can be used to configure the Bandwidth Control Negotiation Mode and Storm Control for Ethernet ports interface fastEthernet Description The interface fastEthernet command is used to enter the interface fastEthernet Configuration Mode and configure the corresponding Fast Ethernet port Syntax interface fastEthernet port Parameter port The Fast Gigabit Ethernet port number Command M
22. Example Display the configuration of 801 X globally TL SL5428E config show dot1x global show dot1x interface Description The show dot1x interface command is used to display all ports or the specified port s configuration information of 801 X Syntax show dot1x interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number Display the configuration of all the ports by default Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of 801 X for Gigabit Ethernet port 25 TL SL5428E config show dot1x interface gigabitEthernet 1 0 25 Display the configuration information of 801 X for all Ethernet ports 97 TL SL5428E BA 6 LLE a EME EG e BRETT TL SL5428E config show dot1x interface show radius accounting Description The show radius accounting command is used to display the configuration of the accounting server Syntax show radius accounting Command Mode Privileged EXEC Mode and Any Configuration Modes Example Display the configuration of the accounting server TL SL5428E config show radius accounting show radius authentication Description The show radius authentication command is used to display the configuration of the RADIUS authentication server Syntax show radius authentication Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration o
23. Interface Ethernet Configure parameters for several Ethernet ports c Interface link aggregation Configure parameters for a link aggregation such as broadcast storm d Interface range link aggregation Configure parameters for multi trunks e Interface vlan Configure parameters for the vlan port e Vlan Configuration Mode In this mode users can create a VLAN and add a specified port to the VLAN 12 TL SL5428E EN LLE A EME Eli e M EE ETT IT 3 Some commands are global that means they can be performed in all modes e show Displays all information of switch for example statistic information port information VLAN information e history Displays the commands history 1 3 Security Levels This switch s security is divided into two levels User level and Admin level User level only allows users to do some simple operations in User EXEC Mode Admin level allows you to monitor configure and manage the switch in Privileged EXEC Mode Global Configuration Mode Interface Configuration Mode and VLAN Configuration Mode Users get the privilege to the User level once connecting console port with the switch or logging in by Telnet However Guest users are restricted to access the CLI Users can enter Privileged EXEC mode from User EXEC mode by using the enable command In default case no password is needed In Global Configuration Mode you can configure password for Admin level by enable password comman
24. LAG active Enable the active LACP mode passive Enable the passive LACP mode Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEhternet Example Add the Fast Ethernet port 2 4 to EtherChannel Group 1 and enable the static LAG TL SL5428E config interface range fastEthernet 1 0 2 4 TL SL5428E config if range channel group 1 mode on 53 TL SL5428E BA 6 0 5 1 a VET Xe DL Eli e M EE ETT IT port channel load balance Description The port channel load balance command is used to configure the Aggregate Arithmetic for LAG To return to the default configurations please use no port channel load balance command Syntax port channel load balance src dst mac src dst ip no port channel load balance Parameter src dst mac The source and destination MAC address When this option is selected the Aggregate Arithmetic will be based on the source and destination MAC addresses of the packets The Aggregate Arithmetic for LAG is src dst mac by default src dst ip The source and destination IP address When this option is selected the Aggregate Arithmetic will be based on the source and destination IP addresses of the packets Command Mode Global Configuration Mode Example Configure the Aggregate Arithmetic for LAG as src dst mac TL SL5428E config port channel load balance
25. LLE A EME Eli e M EE ETT IT show dot1q tunnel mapping interface Description The show dot1q tunnel mapping interface command is used to display the VLAN Mapping port enable state of VLAN Mapping Syntax show dot1q tunnel mapping interface Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the enable state of all VLAN Mapping ports TL SL5428E config show dot1q tunnel mapping interface show dot1q tunnel uplink Description The show dot1q tunnel uplink command is used to display the configuration information of the VLAN VPN Up link ports Syntax show dot1q tunnel uplink Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of the VLAN VPN Up link ports TL SL5428E config show dot1q tunnel uplink 37 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Chapter 7 Voice VLAN Commands Voice VLANs are configured specially for voice data stream By configuring Voice VLANs and adding the ports with voice devices attached to voice VLANs you can perform QoS related configuration for voice data ensuring the transmission priority of voice data stream and voice quality voice vlan Description The voice vlan command is used to enable Voice VLAN function To disable Voice VLAN function please use no voice vlan command Syntax voice vlan vian id no voice vlan Parameter vlan id Specify IEEE 802 1Q VLAN ID ranging from 2 to
26. Mode and Any Configuration Mode Example Display the Aging Time of the MAC address TL SL5428E config show mac address table aging time show mac address table max mac count interface Description The show mac address table max mac count interface command is used to display the security configuration of an Ethernet port or of all Fast Gigabit Ethernet ports Syntax show mac address table max mac count interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the security configuration of all Gigabit Ethernet ports TL SL5428E config show mac address table max mac count interface gigabitEthernet Display the security configuration of Gigabit Ethernet port 25 TL SL5428E config show mac address table max mac count interface gigabitEthernet 1 0 25 116 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide show mac address table interface Description The show mac address table interface command is used to display the address configuration of an Ethernet port Syntax show mac address table interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the address configuration of Fast Ethernet port 1 TL SL5428E con
27. Object Identifier OID for the entry of View ranging from 1 to 61 characters include exclude View Type with include and exclude options They represent the view entry can cannot be managed by the SNMP management station individually Command Mode Global Configuration Mode Example Add a View named view1 configuring the OID as 1 3 6 1 6 3 20 and this OID can be managed by the SNMP management station TL SL5428E config snmp server view view1 1 3 6 1 6 3 20 include snmp server group Description The snmp server group command is used to manage and configure the SNMP group To delete the corresponding SNMP group please use no snmp server group command SNMP v3 provides the VACM View based Access Control Model and USM User Based Security Model mechanisms for authentication The users in the SNMP Group can manage the device via the Read View Write View and Notify View And the authentication mode and the privacy mode guarantee the high security for the communication between the management station and the managed device snmp server group name smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv read read view write write view notify notify view no snmp server group name smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv Parameter name The SNMP Group name ranging from 1 to 16 characters The Group Name Security Model and Security Level com
28. as 11111 the Privacy Mode as DES and the Privacy Password as 22222 TL SL5428E config snmp server user admin local group2 smode v3 slev authPriv cmode MD5 cpwd 11111 emode DES epwd 22222 snmp server community Description The snmp server community command is used to add Community To delete the corresponding Community please use no snmp server community command SNMP v1 and SNMP v2c adopt community name authentication The community name can limit access to the SNMP agent from SNMP network management station functioning as a password Syntax snmp server community name read only read write mib view no snmp server community name Parameter name Community Name ranging from 1 to 16 characters read only read write The access rights of the community with read only and read write options mib view The MIB View for the community to access Command Mode Global Configuration Mode Example Add community public and the community has read write management right to View viewDefault TL SL5428E config snmp server community public read write viewDefault 218 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT snmp server host Description The snmp server host command is used to add Notification To delete the corresponding Notification please use no snmp server host command With the Notification function enabled the switch can initiatively report to the management station about the impo
29. by IEEE DSCP priorities are mapped to the corresponding 802 1p priorities IP datagram will be classified into the egress queue based on the mapping relation between DSCP priority and TC egress queue Example Enable the mapping relation between DSCP Priority and egress queue TL SL5428E config qos dscp 150 TL SL5428E MOCSUCEU MIA EME EG e BRETT qos queue cos map Description The qos queue cos map command is used to configure the mapping relation between IEEE 802 1P priority tag IEEE 802 1Q tag CoS value and the TC egress queue To return to the default configuration please use no qos queue cos map command When 802 1P Priority is enabled the packets with 802 1Q tag are mapped to different priority levels based on 802 1P priority mode The untagged packets are mapped based on port priority mode Syntax qos queue cos map fag cos id tc id no qos queue cos map Parameter tag cos id The 8 priority levels defined by IEEE 802 1P or the priority level the packets with tag are mapped to which ranges from CoS 0 to CoS 7 tc id The egress queue the packets with tag are mapped to It ranges from 0 to 3 which represents TCO TC1 TC2 TC3 respectively Command Mode Global Configuration Mode User Guidelines 1 By default the mapping relation between tag cos and the egress queue is 0 TCO 1 TCO 2 TC1 3 TC1 4 TC2 5 TC2 6 TC3 7 TC3 2 Among the priority levels TCO TC3 the bigger value the higher priori
30. cluster time segment t1 TL SL5428E config cluster timeseg periodic week date 1 4 248 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT backup time Description The backup time command is used to specify the backup time The switch will backup its configurations only when its system time is right at the backup time By default it is 00 00 To return to the default configuration please use no backup time command Syntax backup time backup time no backup time Parameter backup time Specify the backup time in the format of HH MM Command Mode Cluster Time segment Configuration Mode cluster time segment Example Configure the time segment t1 with the backup time 08 00 TL SL5428E config cluster time segment t1 TL SL5428E config cluster timeseg backup time 08 00 cluster manage tftp server Description The cluster manage tftp server command is used to configure the TFTP server for the switch The switch can backup its configurations to the TFTP server or download the configuration file from the TFTP server To delete the TFTP server please use no cluster manage tftp server command Syntax cluster manage tftp server tfip server no cluster manage tftp server Parameter tftp server Enter the IP address of the TFTP server Command Mode Global Configuration Mode 249 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Configure the TFTP server as 192 168 0
31. from 0 to 61440 It is 32768 by default Command Mode Global Configuration Mode Example Configure the bridge priority as 4096 TL SL5428E config spanning tree priority 4096 spanning tree tc defend Description The spanning tree tc defend command is used to configure the TC Protect of Spanning Tree globally To return to the default configuration please use no spanning tree tc defend command A switch removes MAC address entries upon receiving TC BPDUs If a malicious user continuously sends TC BPDUs to a switch the switch will be busy with removing MAC address entries which may decrease the performance and stability of the network Syntax spanning tree tc defend threshold threshold period period no spanning tree tc defend Parameter threshold TC Threshold ranging from 1 to 100 packets By default it is 20 TC Threshold is the maximum number of the TC BPDUs received by the switch in a TC Protect Cycle period TC Protect Cycle ranging from 1 to 10 in seconds By default it is 5 Command Mode Global Configuration Mode Example Configure TC Threshold as 30 packets and TC Protect Cycle as 10 seconds TL SL5428E config spanning tree tc defend threshold 30 period 10 189 TL SL5428E BAS 0 5 1 a EME EG e M EE ETT IT spanning tree timer Description The spanning tree timer command is used to configure forward time hello time and max age of Spanning Tree To return to the default configurations please
32. interface vlan 1 TL SL5428E config if ip address alloc bootp reset Description The reset command is used to reset the switch s software After resetting all configuration of the switch will restore to the factory defaults and your current settings will be lost Syntax reset Command Mode Privileged EXEC Mode 127 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Example Reset the software of the switch TL SL5428E reset reboot Description The reboot command is used to reboot the Switch To avoid damage please don t turn off the device while rebooting Syntax reboot Command Mode Privileged EXEC Mode Example Reboot the switch TL SL5428E reboot copy running config startup config Description The copy running config startup config command is used to save the current settings Syntax copy running config startup config Command Mode Privileged EXEC Mode Example Save current settings TL SL5428E copy running config startup config 128 TL SL5428E BAG 6 LLE a EME Eli e M EE ETT IT copy startup config tftp Description The copy startup config tftp command is used to backup the configuration file from TFTP server Syntax copy startup config tftp ip address p addr filename name Parameter ip addr IP Address of the TFTP server name Specify the name for the configuration file which would be backuped Command Mode Privileged EXEC Mode Example Backup the c
33. logging buffer logging host index Description The logging host index command is used to configure the Log Host To clear the configuration of the specified Log Host please use no logging host index command Log Host is to receive the system log from other devices You can remotely monitor the settings and operation status of other devices through the log host Syntax logging host index dx host ip level no logging host index dx Parameter idx The index of the log host The switch supports 4 log hosts host ip The IP for the log host level The severity level of the log information sent to each log host There are 8 severity levels marked with values 0 7 The smaller value has the higher priority Only the log with the same or smaller severity level value will be sent to the corresponding log host By default it is 6 indicating that the log information marked with 0 6 will be sent to the log host Command Mode Global Configuration Mode Example Set the IP address as 192 168 0 148 the level 5 101 TL SL5428E MOSCA EME EG e BRETT TL SL5428E config logging host index 2 192 168 0 148 5 show logging local config Description The show logging local config command is used to display the configuration of the Local Log including the log buffer and the log file Syntax show logging local config Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of
34. please use no absolute command Syntax absolute start start date end end date no absolute 247 TL SL5428E MOCSUCEU MIA EME Eli e M EE ETT IT Parameter start date The start date in Absolute Mode in the format of MM DD YYYY By default it is 01 01 2000 end date The end date in Absolute Mode in the format of MM DD YYYY By default it is 01 01 2000 The Absolute Mode will be disabled if the start date and end date are both in default value Command Mode Cluster Time segment Configuration Mode cluster time segment Example Configure the time segment t1 with time from May 5 2012 to Oct 5 2012 TL SL5428E config cluster time segment t1 TL SL5428E config cluster timeseg absolute start 05 05 2012 end 10 05 2012 periodic Description The periodic command is used to configure the time segment into Periodic Mode To delete the corresponding Periodic Mode time range please use no periodic command Syntax periodic week date week day no periodic Parameter week day Periodic Mode in the format of 1 3 6 or daily off day working day 1 3 6 represent Monday Tuesday Wednesday and Saturday daily represents every day off day represents weekend and working day represents working day By default the Periodic Mode is disabled Command Mode Cluster Time segment Configuration Mode cluster time segment Example Configure the time segment t1 with time from Monday to Thursday TL SL5428E config
35. please use no ip dhcp snooping trust command Syntax ip dhcp snooping trust no ip dhcp snooping trust Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure the Fast Ethernet port 2 to be a Trusted Port TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if ip dhcp snooping trust 72 TL SL5428E BAG 6 0 5 1 a EME EG e BRETT ip dhcp snooping mac verify Description The ip dhcp snooping mac verify command is used to enable the MAC Verify feature To disable the MAC Verify feature please use no ip dhcp snooping mac verify command There are two fields of the DHCP packet containing the MAC address of the Host The MAC Verify feature is to compare the two fields and discard the packet if the two fields are different Syntax ip dhcp snooping mac verify no ip dhcp snooping mac verify Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the MAC Verify feature for the Fast Ethernet port 2 TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if ip dhcp snooping mac verify ip dhcp snooping limit rate Description The ip dhcp snooping limit rate command is used to enable the Flow Control feature for the DHCP packets The excessive DHCP packe
36. ranges from 0 to 63 By default it is not limited pri Local Priority of QOS Remark Specify the local priority for the data packets matching the corresponding ACL Local Priority ranges from 0 to 3 Command Mode Action Configuration Mode 177 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Example Edit the actions for policy1 For the data packets matching ACL 120 specify the DSCP region as 30 and local priority 2 TL SL5428E config access list policy action policy1 120 TL SL5428E config action qos remark dscp 30 priority 2 access list bind interface Description The access list bind command is used to bind a policy to a specified port To cancel the bind relation please use no access list bind command Syntax access list bind policy name no access list bind policy name Parameter policy name The name of the policy desired to bind Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Bind policy1 to Fast Ethernet port 2 TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if access list bind policy1 access list bind vlan Description The access list bind command is used to bind a policy to a VLAN To cancel the bind relation please use no access list bind command Syntax access list bind policy name no access list bind policy name Parameter policy na
37. request ranging from 1 to 255 The switch will resend the inform request if it doesn t get the response from the management station during the Timeout interval and it will terminate resending the inform request if the resending times reach the specified Retry times 219 TL SL5428E BAGS 0 5 1 aE Tare Xe DL EG e BRETT timeout The maximum time for the switch to wait for the response from the management station before resending a request ranging from 1 to 3600 in seconds Command Mode Global Configuration Mode Example Add a Notification entry and configure the IP Address of the management Host as 192 168 0 146 the UDP port as 162 the User name of the management station as admin the Security Model of the management station as v2c the type of the notifications as inform the maximum time for the switch to wait as 1000 seconds and the retries time as 100 TL SL5428E config snmp server host 192 168 0 146 162 admin smode v2c type inform retries 100 timeout 1000 snmp server enginelD Description Syntax The snmp server enginelD command is used to configure the local and remote enginelD of the switch To restore to the default setting please use no snmp server enginelD command snmp server enginelD local loca engine D remote remote enginelD y no snmp server enginelD Parameter local Local Engine ID for local clients The Engine ID is a unique alphanumeric string used to identify th
38. show qos cos map command is used to display the configuration of IEEE802 1P Priority and the mapping relation between cos id and tc id Syntax show qos cos map Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of IEEE 802 1P Priority and the mapping relation between cos id and tc id TL SL5428E show qos cos map show qos dscp map Description The show qos dscp map command is used to display the configuration of DSCP Priority 154 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Syntax show qos dscp map Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of DSCP Priority TL SL5428E show qos dscp map show qos queue mode Description The show qos queue mode command is used to display the schedule rule of the egress queues Syntax show qos queue mode Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the schedule rule of the egress queues TL SL5428E show qos queue mode show qos status Description The show qos status command is used to display the status of IEEE 802 1P priority and DSCP priority Syntax show qos status Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the status of IEEE 802 1P priority and DSCP priority TL SL5428E show qos status 155 TL SL5428E Ent L A EEES e m EE ETT IT Chapter 24 Port Mirror Commands Port Mirror refers
39. the corresponding port By default the LLDP configuration of all the ports will be displayed Syntax show Ildp interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LLDP configuration of Fast Ethernet port 1 TL SL5428E show lldp interface fastEthernet 1 0 1 show dp local information interface Description The show lldp local information interface command is used to display the LLDP information of the corresponding port By default the LLDP information of all the ports will be displayed Syntax show Ildp local information interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode 238 TL SL5428E BAG 6 0 5 1 A ETAT Te DL Eli e BRETT Example Display the LLDP information of Fast Ethernet port 1 TL SL5428E show lldp local information interface fastEthernet 1 0 1 show lldp neighbor information interface Description The show Ildp neighbor information interface command is used to display the neighbor information of the corresponding port By default the neighbor information of all the ports will be displayed Syntax show lldp neighbor information interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethern
40. the Local Log TL SL5428E config show logging local config show logging loghost Description The show logging loghost command is used to display the configuration of the log host Syntax show logging loghost index Parameter index The index of the log host whose configuration will be displayed Display the configuration of all the log hosts by default Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of the log host 2 TL SL5428E config show logging loghost 2 102 TL SL5428E EnS KY LLE A EME Eli e m EE ETT IT show logging buffer Description The show logging buffer command is used to display the log information in the log buffer according to the severity level Syntax show logging buffer level eve Parameter level Severity level There are 8 severity levels marked with values 0 7 The information of levels with priority not lower than the select level will display Display all the log information in the log buffer by default Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the log information from level O to level 5 in the log buffer TL SL5428E config show logging buffer level 5 show logging flash Description The show logging flash command is used to display the log information in the log file according to the severity level Syntax show logging flash level evel Parameter level Sev
41. the parameters of the ports in different instance IDs as well as view status of the ports in the specified instance Syntax spanning tree mst instance instance id port priority pri cost cost no spanning tree mst instance instance id Parameter instance id Instance ID ranging from 1 to 8 pri Port Priority which must be multiple of 16 ranging from O to 240 By default it is 128 Port Priority is an important criterion on determining if the port will be chosen as the root port by the device connected to this port cost Path Cost ranging from 0 to 200000 The lower value has the higher priority Its default value is O meaning auto Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure the priority of Fast Ethernet port 1 in MST Instance 1 as 64 and path cost as 2000 TL SL5428E config interface fastEthernet 1 0 1 TL SL5428E config if spanning tree mst instance 1 port priority 64 cost 2000 spanning tree priority Description The spanning tree priority command is used to configure the bridge priority To return to the default value of bridge priority please use no spanning tree priority command 188 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Syntax spanning tree priority pri no spanning tree priority Parameter pri Bridge priority ranging
42. the users for login Only the user with this MAC Address you set here is allowed to login To cancel the user access limit please use no user access control command 59 TL SL5428E BA 6 KT LL a VET Xe DL EG e m EE ETT IT Syntax user access control mac based mac addr no user access control Parameter mac addr The source MAC address Only the user with this MAC Address is allowed to login Command Mode Global Configuration Mode Example Configure that only the user with the MAC address 00 00 13 0A 00 01 is allowed to login TL SL5428E config user access control mac based 00 00 13 0A 00 01 user access control port based Description The user access control port based command is used to limit the ports for login Only the users connected to these ports you set here are allowed for login To cancel the user access limit please use no user access control command Syntax user access control port based interface fastEthernet port gigabitEthernet port range fastEthernet port list range gigabitEthernet port list no user access control Parameter port The Fast Gigabit Ethernet port number port list The list group of Ethernet ports You can appoint 5 ports at most Command Mode Global Configuration Mode Example Configure that only the users connected to Fast Ethernet ports 2 6 are allowed to login 60 TL SL5428E BA 6 LLE a EME Eli e BRETT TL SL5428E config user ac
43. those match the corresponding ACL rules by configuring ACLs and actions together for effect The operations here include stream mirror stream condition QoS Remarking and redirect Syntax access list policy name name no access list policy name name Parameter name The Policy Name ranging from 1 to 16 characters Command Mode Global Configuration Mode Example Add a Policy named policy1 TL SL5428E config access list policy name policy1 access list policy action Description The access list policy action command is used to add ACLs and create actions for the policy To set the detailed configuration of actions for a policy please use access list policy action command to access Action Configuration Mode To delete the corresponding actions please use no access list policy action command Syntax access list policy action policy name acl id no access list policy action policy name acl id Parameter policy name The Policy Name ranging from 1 to 16 characters acl id The ID of the ACL to which the above policy is applied 174 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Command Mode Global Configuration Mode Example Add ACL whose ID is 120 to policy1 and create an action for them TL SL5428E config access list policy action policy1 120 redirect interface Description The redirect interface command is used to configure Direction function of policy action for specified ports Syntax
44. tlv select command is used to configure TLVs to be included in outgoing LLDPDU To exclude TLVs please use no Ildp tlv select command By default All TLVs are included in outgoing LLDPDU Syntax lldp tlv select port description system capability system description system name management address port vlan protocol vlan vlan name link aggregation mac phy cfg max frame size power all no dp tlv select port description system capability system description system name management address port vlan protocol vlan vlan name link aggregation mac phy cfg max frame size power all Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Exclude management address and port vlan id TLVs in LLDPDU outgoing from Fast Ethernet port 1 TL SL5428E config interface fastEthernet 1 0 1 TL SL5428E config if no lldp tlv select management address port vlan show Ildp Description The show lldp command is used to display the global configuration of LLDP Syntax show lldp Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of LLDP 237 TL SL5428E BAG 6 0 5 1 WAV EV Xe DL EG e BRETT TL SL5428E show lldp show Ildp interface Description The show Ildp interface command is used to display LLDP configuration of
45. to add promiscuous type port to private VLAN To remove the port from Private VLAN please use no switchport private vlan mapping command Syntax switchport private vlan mapping primary_vlan_id secondary_vlan_id no switchport private vlan mapping primary_vlan_id secondary_vlan_id Parameter primary vlan id Primary VLAN ID ranging from 2 to 4094 secondary vlan id Secondary VLAN ID ranging from 2 to 4094 Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure promiscuous type Fast Ethernet port 3 as a member of primary VLAN 3 and secondary VLAN 4 TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if switchport private vlan mapping 3 4 47 TL SL5428E BA 6 0 5 1 a VET Xe DL EG e m EE ETT IT show vlan private vlan Description The show vlan private vlan command is used to display the Private VLAN configuration information of the switch Syntax show vlan private vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of all Private VLAN TL SL5428E config show vlan private vlan 48 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Chapter9 GVRP Commands GVRP GARP VLAN registration protocol is an implementation of GARP generic attribute registration protocol GVRP allows the switch to automa
46. to display the detailed information of IEEE 802 1Q VLAN By default the detailed information of all the ports will be displayed Syntax show vlan id vian list Parameter vian list Specify IEEE 802 1Q VLAN ID ranging from 1 to 4094 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the detailed information of VLAN 2 10 TL SL5428E config show vlan id 2 10 25 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Chapter A MAC based VLAN Commands MAC VLAN Virtual Local Area Network is the way to classify the VLANs based on MAC Address A MAC address is relative to a single VLAN ID The untagged packets and the priority tagged packets coming from the MAC address will be tagged with this VLAN ID mac vlan mac address Description The mac vlan mac address command is used to create a MAC based VLAN entry To delete a MAC based VLAN entry please use the no mac vlan mac address command Syntax mac vlan mac address mac addr vlan vlan id description descript no mac vlan mac address mac addr Parameter mac addr MAC address in the format of XX XX XX XX XX XX vlan id Specify IEEE 802 1Q VLAN ID ranging from 1 to 4094 descript Give a description to the MAC address for identification which contains 8 characters at most Command Mode Global Configuration Mode Example Create VLAN 2 named TP and the MAC address is 00 11 11 01 01 12 TL SL5428E config ma
47. use no spanning tree timer command Syntax spanning tree timer forward time forward time hello time hello time max age max age no spanning tree timer Parameter forward time Forward Delay which is the time for the port to transit its state after the network topology is changed Forward Delay ranges from 4 to 30 in seconds and it is 15 by default Otherwise 2 Forward Delay 1 gt Max Age hello time Hello Time which is the interval to send BPDU packets and used to test the links Hello Time ranges from 1 to 10 in seconds and it is 2 by default Otherwise 2 Hello Time 1 lt Max Age max age The maximum time the switch can wait without receiving a BPDU before attempting to reconfigure ranging from 6 to 40 in seconds By default it is 20 Command Mode Global Configuration Mode Example Configure forward time hello time and max age for Spanning Tree as 16 seconds 3 seconds and 22 seconds respectively TL SL5428E config spanning tree timer forward time 16 hello time 3 max age 22 spanning tree hold count Description The spanning tree hold count command is used to configure the maximum number of BPDU packets transmitted per Hello Time interval To return to the default configurations please use no spanning tree hold count command 190 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Syntax spanning tree hold count value no spanning tree hold count Parameter va
48. 00000kbps osd Out of Band disposal of Stream Condition It is the disposal way of the data packets those are transmitted beyond the rate There are two options none and discard By default the option is none Command Mode Action Configuration Mode Example Edit the actions for policy1 For the data packets matching ACL 120 in the policy if the rate beyond 1000kbps they will be discarded by the switch TL SL5428E config access list policy action policy1 120 TL SL5428E config action s condition rate 1000 osd discard 176 TL SL5428E BAG 6 0 5 1 a EME EG e BRETT s mirror Description The s mirror command is used to configure Stream Mirror function of policy action to the specified port Syntax s mirror interface fastEthernet port gigabitEthernet port Parameter port The Mirror Port number of Stream Mirror Command Mode Action Configuration Mode Example Edit the actions for policy1 Specify the mirror port as Fast Ethernet port 2 for the data packets matching ACL 120 TL SL5428E config access list policy action policy1 120 TL SL5428E config action s mirror interface fastEthernet 1 0 2 qos remark Description The qos remark command is used to configure QoS Remark function of policy action Syntax qos remark dscp dscp priority pri no qos remark Parameter dscp DSCP of QoS Remark Specify the DSCP region for the data packets matching the corresponding ACL DSCP
49. 1x port method Parameter mac based port based The control type for the port mac based Any client connected to the port should pass the 802 1X authentication for access port based All the clients connected to the port can access the network on the condition that any one of the clients has passed the 802 1X Authentication Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure the Control Type for Gigabit Ethernet port 25 as port based TL SL5428E config interface gigabitEthernet 1 0 25 TL SL5428E config if dot1x port method port based radius Description The radius command is used to configure the parameters of radius Syntax radius auth pri ip auth sec jp auth port port auth key keyvalue acct pri ip acct sec ip acct port port acct key keyvalue timeout value no radius auth port auth key acct port acct key timeout Parameter auth pri jo The IP address of the authentication server auth sec ip The IP address of the alternative authentication server auth port port The UDP port of authentication server s ranging from 1 to 65535 The default value is 1812 95 TL SL5428E BA 6 LLE aE Tare Te DL EG e BRETT auth key keyvalue The shared password for the switch and the authentication servers to exchange messages which cont
50. 32 TL SL5428E MOSCA EME EG e M EE ETT IT Chapter6 VLAN VPN Commands VLAN VPN Virtual Private Network function the implement of a simple and flexible Layer 2 VPN technology allows the packets with VLAN tags of private networks to be encapsulated with VLAN tags of public networks at the network access terminal of the Internet Service Provider And these packets will be transmitted with double tag across the public networks dot1q tunnel Description The dot1q tunnel command is used to enable the VLAN VPN function globally To disable the VLAN VPN function please use the no dot1q tunnel command Syntax dot1q tunnel no dot1q tunnel Command Mode Global Configuration Mode Example Enable the VLAN VPN function globally TL SL5428E config dot1q tunnel dot1q tunnel tpid Description The dot1q tunnel tpid command is used to configure Global TPID of the VLAN VPN To restore to the default value please use the no dot1q tunnel tpid command Syntax dot1q tunnel tpid num no dot1q tunnel tpid 33 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Parameter num The value of Global TPID It must be 4 Hex integers By default it is 8100 Command Mode Global Configuration Mode Example Configure Global TPID of the VLAN VPN as 0x9100 TL SL5428E config dot1q tunnel tpid 9100 dot1q tunnel mapping Description The dot1q tunnel mapping command is used to add the VLAN Mapping entry To de
51. 46 TL SL5428E MOSCA EME e M EE TT IT show interface configuration Description The show interface configuration command is used to display the configurations of an Ethernet port including Port status Flow Control Negotiation Mode and Port description Syntax show interface fastEthernet port gigabitEthernet port configuration Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configurations of all Ethernet ports TL SL5428E config show interface configuration show storm control Description The show storm control command is used to display the storm control information of an Ethernet port Syntax show storm control interface fastEthernet port gigabitEthernet port range fastEthernet port list range gigabitEthernet port list Parameter port The Fast Gigabit Ethernet port number port list The list of Fast Gigabit Ethernet ports Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the storm control information of port Gigabit Ethernet port 25 TL SL5428E config show storm control interface gigabitEthernet 1 0 25 Display the storm control information of port Fast Ethernet ports 4 5 6 7 147 TL SL5428E Aet tream 13 Managied Switch CU Guide L2 Managed Switch CLI Guide TL SL5428E config show storm control interface range fastEthernet 1 0 4 7 show b
52. 55 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Parameter channel group num The EtherChannel Group number ranging from 1 to 14 By default it is empty and will display the information of all EtherChannel Groups detail The detailed information of EtherChannel summary The EtherChannel information in summary Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the detailed information of EtherChannel Group 1 TL SL5428E config show etherchannel 1 detail show etherchannel load balance Description The show etherchannel load balance command is used to display the Aggregate Arithmetic of LAG Syntax show etherchannel load balance Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Aggregate Arithmetic of LAG TL SL5428E config show etherchannel load balance show lacp Description The show lacp command is used to display the LACP information for a specified EtherChannel Group Syntax show lacp channel group num internal neighbor 56 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Parameter channel group num The EtherChannel Group number ranging from 1 to 14 By default it is empty and will display the information of all LACP groups internal The internal LACH information neighbor The neighbor LACP information Command Mode Privileged EXEC Mode and Any Configuration Mode Exam
53. 6 TL SL5428E config cluster manage tftp server 192 168 0 6 cluster manage batch management user config backup Description The cluster manage batch management user config backup command is used to backup the configurations of the switch to the TFTP server Syntax cluster manage batch management user config backup index index filename filename Parameter index Specify the index of the desired switch in cluster it ranges from 0 to 31 filename Type a name for the configuration file which contains 59 characters at most Command Mode Global Configuration Mode Example Backup the configurations of the switch with the index 1 and specify the filename as TL SL5428E TL SL5428E config cluster manage batch management user config backup index 1 filename TL SL5428E cluster manage batch management user config restore Description The cluster manage batch management user config restore command is used to download the configuration file from TFTP server and then restore the switch with the file 250 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Syntax cluster manage batch management user config restore index index filename filename Parameter index Specify the index of the desired switch in cluster it ranges from 0 to 31 filename Specify the filename of the configuration file Command Mode Global Configuration Mode Example Restore the switch with the index 1 to t
54. 7 ACL Commands ACL Access Control List is used to filter data packets by configuring a series of match conditions operations and time ranges It provides a flexible and secured access control policy and facilitates you to control the network security time range Description The time range command is used to add Time Range To delete the corresponding Time Range please use no time range command A time range based ACL enables you to implement ACL control over packets by differentiating the time ranges A time range can be specified in each rule in an ACL The rule takes effect only when the specified time range is configured and the system time is within the time range Syntax time range name no time range name Parameter name The Time Range name ranging from 1 to 16 characters Command Mode Global Configuration Mode Example Add a time range named tSeg1 TL SL5428E config time range tSeg1 absolute Description The absolute command is used to configure a time range into an Absoluteness Mode To delete the corresponding absolute mode time range please use no absolute command Syntax absolute start sfart date end end date 166 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT no absolute Parameter start date The start date in Absolute Mode in the format of MM DD YYYY By default it is 01 01 2000 end date The end date in Absolute Mode in the format of MM DD YYYY By default it is 01
55. AC VID PORT binding table Syntax show ip source binding 74 TL SL5428E BA 6 KT LLE a VET Xe DL EG e BRETT Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the IP MAC VID PORT binding table TL SL5428E config show ip source binding show ip dhcp snooping Description The show ip dhcp snooping command is used to display the running status of DHCP Snooping Syntax show ip dhcp snooping Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the running status of DHCP Snooping TL SL5428E show ip dhcp snooping show ip dhcp snooping information Description The show ip dhcp snooping information command is used to display the Option 82 configuration status of DHCP Snooping Syntax show ip dhcp snooping information Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Option 82 configuration status of DHCP Snooping TL SL5428E show ip dhcp snooping information 75 TL SL5428E N LLE A EEN EG e BRETT show ip dhcp snooping interface Description The show ip dhcp snooping interface command is used to display the DHCP Snooping configuration of a desired Fast Gigabit Ethernet ports or of all Ethernet ports Syntax show ip dhcp snooping interface fastEthernet port gigabitEthernet port Parameters port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Exampl
56. BA 6 KY LLE a EME Eli e BRETT Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEhternet Example Configure the Fast Ethernet ports 2 5 as the Trusted Port TL SL5428E config interface range fastEthernet 1 0 2 5 TL SL5428E config if range ip arp inspection trust ip arp inspection interface Description The ip arp inspection command is used to enable the ARP Defend function To disable the ARP detection function please use no ip arp inspection command ARP Attack flood produces lots of ARP Packets which will occupy the bandwidth and slow the network speed extremely With the ARP Defend enabled the switch can terminate receiving the ARP packets for 300 seconds when the transmission speed of the legal ARP packet on the port exceeds the defined value so as to avoid ARP Attack flood Syntax ip arp inspection no ip arp inspection Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEhternet Example Enable the arp defend function for the Fast Ethernet ports 2 6 TL SL5428E config interface range fastEthernet 1 0 2 6 TL SL5428E config if range ip arp inspection 78 TL SL5428E MOSCA VET Xe DL Eli e BRETT ip arp inspection limit rate Description The ip arp inspection limit rate command is used to configure the AR
57. BAG 6 0 5 1 a EEN EG e BRETT media type Description The media type command is used to configure the media type of Combo port For a Combo port the media type should be configured before you set its speed and mode Syntax media type 1 45 sfp Parameter rj45 sfp Media type Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Configure the media type of Combo port 28T as SFP TL SL5428E config interface gigabitEthernet 1 0 28 TL SL5428E config if H media type sfp duplex Description The duplex command is used to configure the Duplex Mode for an Ethernet port To return to the default configuration please use no duplex command Syntax duplex full half no duplex Parameter full half The duplex mode of the Ethernet port There are two options full duplex mode default and half duplex mode Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure the Duplex Mode as full duplex for Gigabit Ethernet port 25 140 TL SL5428E MOSCA EME EG e BRETT TL SL5428E config interface gigabitEthernet 1 0 25 TL SL5428E config if duplex full speed Description The speed command is used to configure the Speed Mode for an Ethernet port To return to the default configuration please use no speed command Synta
58. C address VLAN and the connected Port number of the Host together Besides it also provide information about the commands used for monitoring the process of the Host obtaining the IP address from DHCP server and record the IP address MAC address VLAN and the connected Port number of the Host for automatic binding Chapter 13 ARP Inspection Commands Provide information about the commands used for protecting the switch from the ARP cheating or ARP Attack Chapter 14 IP Verify Source Commands Provide information about the commands used for guarding the IP Source by filtering the IP packets based on the IP MAC Binding entries Chapter 15 DoS Defend Command Provide information about the commands used for DoS defend and detecting the DoS attack Chapter 16 IEEE 802 1X Commands Provide information about the commands used for configuring IEEE 802 1X function Chapter 17 System Log Commands Provide information about the commands used for configuring system log Chapter 18 SSH Commands Provide information about the commands used for configuring and managing SSH Security Shell Chapter 19 SSL Commands Provide information about the commands used for configuring and managing SSL Secure Sockets Layer Chapter 20 MAC Address Commands Provide information about the commands used for MAC Address configuration Chapter 21 System Configuration Commands Provide information about the commands used for configuring the System info
59. C address entries upon receiving TC BPDUs If a malicious user continuously sends TC BPDUs to a switch the switch will be busy with removing MAC address entries which may decrease the performance and stability of the network With the Protect of Spanning Tree function enabled you can configure the number of TC BPDUs in a required time so as to avoid the process of removing MAC addresses frequently Syntax spanning tree guard tc no spanning tree guard tc Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the TC Protect of Spanning Tree for Fast Ethernet port 2 TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if spanning tree guard tc spanning tree mcheck Description The spanning tree mcheck command is used to enable MCheck 194 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Syntax spanning tree mcheck Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable MCheck for Fast Ethernet port 2 TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if spanning tree mcheck show spanning tree active Description The show spanning tree active command is used to display the active information of spanning tree Syntax show spanning tree ac
60. D risan aaeeei mareek Eaei a E e E Aa aea E A EEEE gaee uae EEE aes TaN EE E aeai 220 somp server traps SAMP viii ise AE 221 snmp server traps Wnk status 222 SAME Serer MODS ii ta 222 XI SNiMp Server traps Macri ee 223 snmp server traps van 224 EI E e EE 225 A tings te shes Sicdaalenndad be A oben deutataadeeds A Gita ene 225 A One ea ah ean Se a eee 226 SNOW SNMP SEPvels feces ol a AA AAA e es les 228 SNOW SMMP SEFVET VI Wow fesse Attest Eeer eebe etait 228 show snmp server group 0 eee eee 229 Show sNMp Server TE 229 show snmp server Commun 230 Show snmp Server hOSt iiie cenit eneee iii deenaa EEE A EN aa A seas sues Oaa KEANE AKEN EAN Ee AEE Tat 230 show snmp server nginelD a AANEREN ENEE ENEE anes snes ENEE ANEREN EE ena 230 SNOW une Me Ee TEEN 231 NS titt tten tian trunrEAnEEEEEEE EEES tEEE NEEE NEEE EEEE tEEE ennnen 231 Ge Vin neu EE EE 232 Chapter 31 LLDP ComMandS ooonnnnnccccccccconnnnnannncnencncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnenennnnns 233 A Stevie ater cece Mattar eee leche dad ote oat les Gat bce ciitee a titan tale a 233 Hap hold pl concretado role 233 ele But EE 234 ele 235 Help Rue En LEE 235 ele Uu CN 236 lldprtlveselect cat rice 237 Sleigh eege AA Ee 237 show Ildp interface tii AAA Se AR RAE e 238 show Ildp local information Interface 238 show lldp neighbor information interface ooococcicocococcccnccccconnononcnnnonocnnnannnnnnnconnnnonannnnnncnno 239 show lldp traffic interface oonoooc
61. Description The spanning tree mode command is used to configure the STP mode of the switch To return to the default configurations please use no spanning tree mode command Syntax spanning tree mode stp rstp mstp no spanning tree mode Parameter stp Spanning Tree Protocol the default value rstp Rapid Spanning Tree Protocol mstp Multiple Spanning Tree Protocol Command Mode Global Configuration Mode Example Configure the spanning tree mode as mstp TL SL5428E config spanning tree mode mstp 184 TL SL5428E BAGS LLE Wa VET Xe DL EG e BRETT spanning tree mst configuration Description The spanning tree mst configuration command is used to access MST Configuration Mode from Global Configuration Mode as to configure the VLAN Instance mapping region name and revision level To return to the default configuration of the corresponding Instance please use no spanning tree mst configuration command Syntax spanning tree mst configuration no spanning tree mst configuration Command Mode Global Configuration Mode Example Enter into the MST Configuration Mode TL SL5428E config spanning tree mst configuration TL SL5428E config mst instance Description The instance command is used to configure the VLAN Instance mapping To remove the VLAN instance mapping or disable the corresponding instance please use no instance command When an instance is disabled the related mapping VLAN
62. EC Mode 15 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide TL SL5428E config enable password admin disable Description The disable command is used to return to User EXEC Mode from Privileged EXEC Mode Syntax disable Command Mode Privileged EXEC Mode Example Return to User EXEC Mode from Privileged EXEC Mode TL SL5428E disable TL SL5428E gt configure Description The configure command is used to access Global Configuration Mode from Privileged EXEC Mode Syntax configure Command Mode Privileged EXEC Mode Example Access Global Configuration Mode from Privileged EXEC Mode TL SL5428E configure TL SL5428E config exit Description The exit command is used to return to the previous Mode from the current 16 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Mode Syntax exit Command Mode Any Configuration Mode Example Return to Global Configuration Mode from Interface Configuration Mode and then return to Privileged EXEC Mode TL SL5428E config if exit TL SL5428E config exit TL SL5428E end Description The end command is used to return to Privileged EXEC Mode Syntax end Command Mode Any Configuration Mode Example Return to Privileged EXEC Mode from Interface Configuration Mode TL SL5428E config if end TL SL5428E show history Description The show history command is used t
63. EEEEEEEEEEEEEEEE reenen 189 SPANNING treeS Lu 190 spanning tree Noid count ee NEEE E NETEN EE ESSE E NETE EEVUE 190 spanning tree MAX NOPS EE 191 Spanning tree Dpdufilter oooooooconccoooconoconoconnnonnononconnnonnnonnnonnnnnnnnnnnnnnnnnnnnnr nn nn nnnnnnnnnnnos 192 spanning tree Dpduguard ee eee 192 Spanning tree guard lOOP voir ee aea aaa Ne aE a aa ERa 193 spanning tree guard root 193 Spanning tree guard EE 194 Spanning tree MCHECK EE 194 SHOW Spanning tree active 10 ceeeeeeeeeee eect eee eee aes aaeeaaeeaaeeaaee sues cues aaeeaaeeaeeeaaeeaaeeaeeeaeeaaaeaaes 195 show spanning tree bridge cococcccccccccconcconcnonnnonononononononnnnnnonnnonnnonnnnnnnnnnnnnnnnnnnnnncnnncnnncnnss 195 show spanning tree interface ooooococoonocccccccccoconnconnnncnnnnonocnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnneninnnnnnnnnnno 196 show spanning tree interface Security oooocconcinocococnncccccnonnnononcnnnncnnnnnnnnnnnnnnnnoninnnnnnnnnnnnnenens 196 Show Spanning tree mei 197 Chapter 29 IGMP CGomrangle oia 199 Ip IGMP SNOOPING GlObal serin ae e e e a a a N E Ea N aa a eda 199 ip igmp snoopipngt ntertace conan nn nnnnnnnennnnannnnnnnnaneness 199 ip igmp snooping immediate leave o oooccccccnncnncnnnncnnncnnnnnnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennninnn 200 ip igmp snooping drop upknown 200 ip igmp snooping vlan config eecceceece cece eeeeeeeeeeeeeeeeeeeeceeeaaeeeeeeeesesenccaeeeeeeeeeeseeceuseneeeeees 201 ip igmp sno
64. Example Display the time information of the switch TL SL5428E show system time show system time dst Description The show system time dst command is used to display the DST time information of the switch Syntax show system time dst Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the DST time information of the switch TL SL5428E show system time dst show system time ntp Description The show system time ntp command is used to display the NTP mode configuration information Syntax show system time ntp Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the NTP mode configuration information of the switch TL SL5428E show system time ntp 133 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT show system info Description The show system info command is used to display system description system name device location system contact hardware version firmware version system time run time and so on Syntax show system info Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the system information TL SL5428E show system info show running config Description The show running config command is used to display the current operating configuration of the system or of a specified port Syntax show running config interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit
65. Join message again before the timer times out value The value of the timer The LeaveAll Timer ranges from 1000 to 30000 centiseconds and the default value is 1000 The Join Timer ranges from 20 to 1000 centiseconds and the default value is 20 The Leave Timer ranges from 60 to 3000 centiseconds and the default value is 60 Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEhternet Example Set the GARP leaveall timer of Fast Ethernet port 6 as 2000 centiseconds and restore the join timer of it to the default value TL SL5428E config interface fastEthernet 1 0 6 TL SL5428E config if gvrp timer leaveall 2000 TL SL5428E config if no gvrp timer join 51 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT show gvrp global Description The show gvrp global command is used to display the global GVRP status Syntax show gvrp global Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global GVRP status TL SL5428E config show gvrp global show gvrp interface Description The show gvrp interface command is used to display the GVRP configuration information of a specified Ethernet port or of all Ethernet ports Syntax show gvrp interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number By default the GVRP configuration inf
66. N ports via the authentication Only the supplicant passing the authentication can access the LAN dot1x system auth control Description The dot1x system auth control command is used to enable the IEEE 802 1X function globally To disable the IEEE 802 1X function please use no dot1x system auth control command Syntax dot1x system auth control no dot1x system auth control Command Mode Global Configuration Mode Example Enable the IEEE 802 1X function TL SL5428E config dot1x system auth control dot1x auth method Description The dot1x auth method command is used to configure the Authentication Method of IEEE 802 1X and the default 802 1x authentication method is eap md5 To restore to the default 802 1x authentication method please use no dot1x auth method command Syntax dot1x auth method pap eap md5 no dot1x auth method Parameter pap eap md5 Authentication Methods 89 TL SLSA7pERIGCEIORRKR EIET DL Eli e BRETT pap IEEE 802 1X authentication system uses extensible authentication protocol EAP to exchange information between the switch and the client The transmission of EAP packets is terminated at the switch and the EAP packets are converted to the other protocol such as RADIUS packets for transmission eap md5 IEEE 802 1X authentication system uses extensible authentication protocol EAP to exchange information between the switch and the client The EAP protocol pac
67. P speed of a specified port To restore to the default speed please use no ip arp inspection limit rate command Syntax ip arp inspection limit rate value no ip arp inspection limit rate Parameter value The value to specify the maximum amount of the received ARP packets per second ranging from 10 to 100 in pps packet second By default the value is 15 Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEhternet Example Configure the maximum amount of the received ARP packets per second as 50 pps for Fast Ethernet port 5 TL SL5428E config interface fastEthernet 1 0 5 TL SL5428E config if ip arp inspection limit rate 50 ip arp inspection recover Description The ip arp inspection recover command is used to restore a port to the ARP transmit status from the ARP filter status Syntax ip arp inspection recover Command Mode Interface Configuration Mode Interface fastEthernet Interface range fastEthernet Interface gigabitEthernet Interface range gigabitEhternet 79 TL SL5428E BAG 6 KY LLE a EME EG e BRETT Example Restore Fast Ethernet port 5 to the ARP transmit status TL SL5428E config interface fastEthernet 1 0 5 TL SL5428E config if ip arp inspection recover show ip arp inspection Description The show ip arp inspection command is used to display the ARP detection global con
68. Parameter fa forward list Configure Fast Ethernet ports to the forward port list It is optional gi forward list Configure Gigabit Ethernet ports to the forward port list It is optional Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Set Gigabit Ethernet ports 25 27 to the forward port list of Gigabit Ethernet 28 TL SL5428E config interface range gigabitEthernet 1 0 28 TL SL5428E config if range port isolation gi forward list 1 0 25 27 Set all the Ethernet ports to forward port list of Fast Ethernet port 2 namely restore to the default setting TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if range no port isolation 159 TL SLSA7pERIGCEIORRKR EIET DL EG e BRETT show port isolation Description The show port isolation command is used to display the forward port list of a port Syntax show port isolation interface fastEthernet port gigabitEthernet port Parameter port The number of Ethernet port you want to show its forward port list in the format of 1 0 2 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the forward list of Fast Ethernet port 3 TL SL5428E show port isolation interface fastEthernet 1 0 3 Display the forward list of all Ethernet ports TL SL5428E show port isolation interface 160 TL
69. SL5428E MOSCA EME EG e M EE ETT IT Chapter 26 Loopback Detection Commands With loopback detection feature enabled the switch can detect loops using loopback detection packets When a loop is detected the switch will display an alert or further block the corresponding port according to the configuration loopback detection global Description The loopback detection command is used to enable the loopback detection function globally To disable it please use no loopback detection command Syntax loopback detection no loopback detection Command Mode Global Configuration Mode Example Enable the loopback detection function globally TL SL5428E config loopback detection loopback detection interval Description The loopback detection interval command is used to define the interval of sending loopback detection packets from switch ports to network aiming at detecting network loops periodically Syntax loopback detection interval interval time Parameter interval time The interval of sending loopback detection packets It ranges from 1 to 1000 seconds By default this value is 30 Command Mode Global Configuration Mode 161 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Example Specify the interval time as 50 seconds TL SL5428E config loopback detection interval 50 loopback detection recovery time Description The loopback detection recovery time command is used to configure the time
70. TP LINK CLI Reference Guide TL SL5428E 24 Port 10 100Mbps 4 Port Gigabit JetStream L2 Managed Switch REV1 4 0 1910010916 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TIP LINIK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2013 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com CONTENTS o ecctecevecctecscecctecs vex ctucasies ctedaves ctenacis cbetecesctecavesctetiececacedecedcvedecetecedecedczsdacecaze 1 Chapter1 Using the CLl sseeeeeeeeeeeeeEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEen 4 1 1 Accessing the Cl 4 1 1 1 Eogon by ar Console Portuaria 4 T12 Beete net EE 6 1 2 CL Command Modes veto tos tata 10 1 3 Security EE 13 14 Conventions a ci dane AAA AAA AAA 13 1 4 1 Format CONVeNtiONS coccccinnnococccncncccinnnnnonnnononennoncnnnnnnnnnnnncanannnnnnnnnncnceninnannnnncnn 13 1 42 Special Characters cutre Es 14 1 4 3 Parameter kort eegeieert geed ie ii ae 14 Chapter A hee ee ees 15 ON ADC EE 15 enable password soz aes se ec eege ee bed Ski nike ied eh es ea ted be ate
71. VLAN mode for the switchport Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure Fast Ethernet port 3 as host TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if switchport private vlan host switchport private vlan host association Description The switchport private vlan host association command is used to add host type port to private VLAN To remove the port from Private VLAN please use no switchport private vlan host association command Syntax switchport private vlan host association primary_vian_id secondary_vlan_id no switchport private vlan host association primary_vlan_id secondary_vlan_id Parameter primary vlan id Primary VLAN ID ranging from 2 to 4094 secondary vlan id Secondary VLAN ID ranging from 2 to 4094 Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet 46 TL SL5428E BA 6 0 5 1 a EME Eli e BRETT Example Configure host type Fast Ethernet port 3 as a member of primary VLAN 3 and secondary VLAN 4 TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if switchport private vlan host association 3 4 switchport private vlan mapping Description The switchport private vlan mapping command is used
72. abitEthernet interface range gigabitEthernet Example Enable the BPDU filter function for Fast Ethernet port 2 TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if spanning tree bpdufilter spanning tree bpduguard Description The spanning tree bpduguard command is used to enable the BPDU protect function for a port With the BPDU protect function enabled the port will set itself automatically as ERROR PORT when it receives BPDU packets and the port will disable the forwarding function for a while To disable the BPDU protect function please use no spanning tree bpduguard command Syntax spanning tree bpduguard no spanning tree bpduguard Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the BPDU protect function for Fast Ethernet port 2 192 TL SL5428E MOSCA EME EG e BRETT TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if spanning tree bpduguard spanning tree guard loop Description The spanning tree guard loop command is used to enable the Loop Protect function for a port Loop Protect is to prevent the loops in the network brought by recalculating STP because of link failures and network congestions To disable the Loop Protect function please use no spanning tree guard loop command Syntax spanning tree guard loop no spanning tree guard
73. able SNMP extended MAC address related traps which include four types new full learn mode change and max learned To disable the sending of SNMP extended MAC address related traps please use no snmp server traps mac command Syntax snmp server traps mac new full learn mode change max learned no snmp server traps mac new full learn mode change max learned Parameter new Enable new MAC address trap It is sent when the switch learns new MAC address including dynamic address static address and filter address full Enable MAC address table trap It is sent when the MAC address table is full learn mode change Enable MAC address learn mode change trap It is sent when MAC address learning mode of the switch changes 223 TL SL5428E BAG S051 a EME EG e BRETT max learned Enable MAC address max learned trap It is sent when the amount of learned MAC address reaches the limit which is configured in port security module Command Mode Global Configuration Mode Example Enable all SNMP extended MAC address related traps for the switch TL SL5428E config snmp server traps mac Enable new MAC address trap only for the switch TL SL5428E config snmp server traps mac new snmp server traps vlan Description The snmp server traps vlan command is used to enable SNMP extended VLAN related traps which include two types create and delete To disable this function please use no snm
74. after which the blocked port would automatically recover to normal status Syntax loopback detection recovery time recovery time Parameter recovery time The time after which the blocked port would automatically recover to normal status and the loopback detection would restart It is integral times of detection interval ranging from 3 to 100 and the default value is 3 Command Mode Global Configuration Mode Example Configure the recovery time as 3 times of detection interval TL SL5428E config loopback detection recovery time 3 loopback detection interface Description The loopback detection command is used to enable the loopback detection function of the specified port To disable it please use no loopback detection command Syntax loopback detection no loopback detection Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet 162 TL SL5428E BAG 6 0 5 1 a EME Eli e BRETT Example Enable the loopback detection function of Gigabit Ethernet ports 25 27 TL SL5428E config interface range gigabitEthernet 1 0 25 27 TL SL5428E config if range loopback detection loopback detection config Description The loopback detection config command is used to configure the process mode and recovery mode for the ports by which the switch copes with the detected loops Syntax loopback detection config pr
75. ains 15 characters at most acct pri jo The IP address of the accounting server acct sec ip The IP address of the alternative accounting server acct port port The UDP port of accounting server s ranging from 1 to 65535 The default value is 1813 acct key keyvalue The shared password for the switch and the accounting servers to exchange messages which contains 15 characters at most timeout value The maximum time for the switch to wait for the response before resending a request to the supplicant ranging from 1 to 9 in second By default it is 3 Command Mode Global Configuration Mode Example Configure the IP address of the accounting server as 10 20 1 100 and password as tplink TL SL5428E config radius auth pri 10 20 1 100 auth key tplink radius server account Description The radius server account command is used to enable the accounting feature To disable the accounting feature please use no radius server account command Syntax radius server account no radius server account Command Mode Global Configuration Mode Example Enable the accounting feature 96 TL SLSA7pERIGCEIORRKR EIET DL EG e BRETT TL SL5428E config radius server account show dot1x global Description The show dot1x global command is used to display the global configuration of 801 X Syntax show dot1x global Command Mode Privileged EXEC Mode and Any Configuration Mode
76. ample Specify the DST start time of the switch as 2 00 am on the first Sunday in May the end time as 2 00 am on the last Sunday in October and the offset as 45 minutes TL SL5428E config system time dst recurring first Sun May 02 00 last Sun Oct 02 00 45 123 TL SL5428E BAG 6 0 5 1 a EEN EG e BRETT hostname Description The hostname command is used to configure the system name To clear the system name information please use no hostname command Syntax hostname hostname no hostname hostname Parameter hostname System Name ranging from 1 to 32 characters It is the product name by default Here it is TL SL5428E Command Mode Global Configuration Mode Example Configure the system name as TPLINK TL SL5428E config hostname TPLINK location Description The location command is used to configure the system location To clear the system location information please use no location command Syntax location ocation no location ocation Parameter location Device Location It consists of 32 characters at most It is SHENZHEN by default Command Mode Global Configuration Mode Example Configure the system location as GUANGZHOU TL SL5428E config location GUANGZHOU 124 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT contact info Description The contact info command is used to configure the system contact information To clear the system contact information
77. amplings from the port ranging from 10 to 3600 in seconds By default it is 1800 owner name The owner of the history sample entry ranging from 1 to 16 characters By default it is monitor Command Mode Global Configuration Mode Example Configure the sample port as 2 and the sample interval as 100 seconds for the entry 1 3 TL SL5428E config rmon history 1 3 interface fastEthernet 1 0 2 interval 100 owner owner rmon event Description The rmon event command is used to configure the entries of SNMP RMON Event To return to the default configuration please use no rmon event 225 TL SLSA7pERIGCEIORRKR EIET DL EG e M EE ETT IT command Event Group as one of the commonly used RMON Groups is used to define RMON events Alarms occur when an event is detected Syntax rmon event index user user name description descript type none log notify log notify owner owner name y no rmon event index Parameter index The index number of the event entry ranging from 1 to 12 You can only select one entry for each command user name The name of the User to which the event belongs ranging from 1 to 16 characters By default it is public descript The description of the event ranging from 1 to 16 characters By default it is empty type The event type with none log notify and both options None indicates no proces
78. and is used to display the port state of MAC based VLAN Syntax show mac vlan interface Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the enable state of all the ports TL SL5428E config show mac vlan interface 28 TL SL5428E MOCSUCEU MIA EME EG e m EE ETT IT Chapter 5 Protocol based VLAN Commands Protocol VLAN Virtual Local Area Network is the way to classify VLANs based on Protocols A Protocol is relative to a single VLAN ID The untagged packets and the priority tagged packets matching the protocol template will be tagged with this VLAN ID protocol vlan template Description The protocol vlan template command is used to create Protocol based VLAN template To delete Protocol based VLAN template please use no protocol vian template command Syntax protocol vlan template name protoco name ether type type no protocol vlan template template idx Parameter protocol name Give a name for the Protocol based VLAN Template which contains 8 characters at most type Enter the Ethernet protocol type field in the protocol template composing of 4 Hex integers template idx The number of the Protocol based VLAN Template You can get the template corresponding to the number by the show protocol vlan template command Command Mode Global Configuration Mode Example Create a Protocol based VLAN template named TP whose Ethernet protocol type is 0x2024
79. andwidth Description The show bandwidth command is used to display the bandwidth limit information of Ethernet port Syntax show bandwidth interface fastEthernet port gigabitEthernet port range fastEthernet port list range gigabitEthernet port list Parameter port The Fast Gigabit Ethernet port number port list The list of Fast Gigabit Ethernet ports Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the bandwidth limit information of Gigabit Ethernet port 25 TL SL5428E config show bandwidth interface gigabitEthernet 1 0 25 Display the bandwidth limit information of Fast Ethernet ports 2 6 7 8 TL SL5428E config show bandwidth interface range fastEthernet 1 0 2 1 0 6 8 148 TL SL5428E MOSCA EEN Eli e BRETT Chapter 23 QoS Commands QoS Quality of Service function is used to optimize the network performance It provides you with network service experience of a better quality qos Description The qos command is used to configure CoS Class of Service based on port To return to the default configuration please use no qos command Syntax qos cos id no qos Parameter cos id The priority of port It ranges from O to 7 which represent CoSO CoS7 respectively By default the priority is 0 Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEth
80. ans that you can edit modify and view all the settings of different functions It is admin by default disable enable Enable disable the user The new added user is enable by default simple cipher The way of displaying password in configuration file By default it is simple Mode Global Configuration Mode Add and enable a new admin user named tplink of which the password is password 58 TL SL5428E MOSCA EME Eli e BRETT TL SL5428E config user name tplink password password type admin status enable user access control ip based Description The user access control ip based command is used to limit the IP range of the users for login Only the users within the IP range you set here are allowed to login To cancel the user access limit please use no user access control command Syntax user access control ip based p addr ip mask no user access control Parameter ip addr The source IP address Only the users within the IP range you set here are allowed to login ip mask The subnet mask of the IP address Command Mode Global Configuration Mode Example Configure that only the user with the IP address 192 168 0 148 is allowed to login TL SL5428E config user access control ip based 192 168 0 148 255 255 255 255 user access control mac based Description The user access control mac based command is used to limit the MAC Address of
81. arameter The aging time of the local information in the neighbor device is determined by the actual TTL value used in the sending LLDPDU TTL Hold Multiplier Transmit Interval To return to the default configuration please use no Ildp hold multiplier command Syntax dp hold multiplier multiplier no Ildp hold multiplier 233 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Parameter multiplier Configure the Hold Multiplier parameter It ranges from 2 to 10 By default it is 4 Command Mode Global Configuration Mode Example Specify Hold Multiplier as 5 TL SL5428E config lldp hold multiplier 5 Ildp timer Description The lldp timer command is used to configure the parameters about transmission To return to the default configuration please use no lldp timer command Syntax lldp timer tx interval tx interval tx delay tx delay reinit delay reinit delay notify interval notify interval fast count fast count no lidp timer tx interval tx delay reinit delay notify interval fast count Parameter tx interval Configure the interval for the local device to transmit LLDPDU to its neighbors The value ranges from 5 to 32768 and the default value is 30 seconds tx delay Configure a value from 1 to 8192 in seconds to specify the time for the local device to transmit LLDPDU to its neighbors after changes occur so as to prevent LLDPDU being sent frequently By default it
82. ault it is empty Command Mode Interface Configuration Mode interface vian Example Configure the system IP as 192 168 0 69 and the Subnet Mask as 255 255 255 0 when the management VLAN of the switch is VLAN 1 TL SL5428E config interface vlan 1 TL SL5428E config if ip address 192 168 0 69 255 255 255 0 ip address alloc dhcp Description The ip address alloc dhcp command is used to enable the DHCP Client function When this function is enabled the switch will obtain IP from DHCP Client server This command should be configured in the Interface Configuration Mode of the management VLAN Syntax ip address alloc dhcp Command Mode Interface Configuration Mode interface vian 126 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Example Enable the DHCP Client function when the management VLAN of the switch is VLAN1 TL SL5428E config interface vlan 1 TL SL5428E config if ip address alloc dhcp ip address alloc bootp Description The ip address alloc bootp command is used to enable the BOOTP Protocol When the BOOTP Protocol is enabled the switch will obtain IP address from BOOTP Server This command should be configured in the Interface Configuration Mode of the management VLAN Syntax ip address alloc bootp Command Mode Interface Configuration Mode interface vian Example Enable the BOOTP Protocol to obtain IP address from BOOTP Server when the management VLAN of the switch is VLAN1 TL SL5428E config
83. c vlan mac address 00 11 11 01 01 12 vlan 2 description TP 26 TL SL5428E MOSCA EME EG e M EE ETT IT mac vlan Description The mac vlan command is used to enable a port for the MAC based VLAN feature Only the port is enabled can the configured MAC based VLAN take effect To disable the MAC based VLAN function please use no mac vlan command All the ports are disabled by default Syntax mac vlan no mac vlan Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the Fast Ethernet port 3 for the MAC based VLAN feature TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if mac vlan show mac vlan Description The show mac vlan command is used to display the information of the MAC based VLAN entry MAC address and VLAN ID can be used to filter the displayed information Syntax show mac vlan all mac address mac adar vlan vian id y Command Mode Privileged EXEC Mode and Any Configuration Mode Parameter mac addr MAC address in the format of XX XX XX XX XX XX vlan id Specify IEEE 802 1Q VLAN ID ranging from 1 to 4094 27 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Example Display the information of all the MAC based VLAN entry TL SL5428E config show mac vlan all show mac vlan interface Description The show mac vlan interface comm
84. ccnnononicinocococccnnncoconnnnrnncnnnnnononcnnnnnncnnnnnnnncannnnncnnnn nn co teere EEE 239 Chapter 32 Cluster COMMAnNdS cccccccccnonnnncnncncncncnnnananannnnnnnnnnnnnnnnnnnnnnnennnnnnnnnanas 241 CIS Le LW A A AA ee a Eee 241 el O io A A A 242 Cluster Erleis wedi AAA AAA AAA A A aai 243 O O eet 243 e Mee E 244 Cluster commander 244 CIUSTO MANAGES etica 245 XII cluster DEE nd e tee 245 AP 246 Cluster individual nneennsennsesreesressrssrrssrrssrrrerrrerrrerrrerrtttrrtrrterrterrretttettrertrerrrertrertrernne 246 Cluster en E 247 ADSONUle saci os eG E A A a aea 247 POMOGIC EE 248 DACKUP TT 249 cluster Manage Uip sener cess seceaeeeeeeeeseseeeciseseeeeesessseeeseaneess 249 cluster manage batch management user config backup 250 cluster manage batch management user config restore cocccccccnnccnnnnnnnnoncnnncnonnnnnnnnnss 250 cluster manage batch management user config auto backup 251 cluster manage batch management Cancel 252 Nee E gin et EE 252 SNOW EEN 253 Show cluster E 253 Beidel duu Le CH EEN 254 show cluster Dme sedmment kk 254 show cluster manage batch management enne 255 XIII TL SL5428E BAG 6 0 5 1 KREIEN le BRETT Preface This Guide is intended for network administrator to provide referenced information about CLI Command Line Interface The device mentioned in this Guide stands for TL SL5428E JetStream L2 Managed Switch Overview of this Guide Chapter 1 Using the CLI Prov
85. cess control port based interface range fastEthernet 1 0 2 6 user max number Description The user max number command is used to configure the maximum login user number at the same time To cancel the limit on login number please use no user max number command Syntax user max number admin num guest num no user max number Parameter admin num The maximum number of the users allowed to log on as Admin ranging from 1 to 16 The total number of Admin and Guest should be less than 16 guest num The maximum number of the users allowed to log on as Guest ranging from 0 to 15 The total number of Admin and Guest should be less than 16 Command Mode Global Configuration Mode Example Configure the maximum number of users login as Admin and Guest as 5 and 3 TL SL5428E config user max num 5 3 user idle timeout Description The user idle timeout command is used to configure the timeout time of the switch To restore to the default timeout time please use no user idle timeout command Syntax user idle timeout minutes no user idle timeout 61 TL SL5428E BA 6 KY LL a EME EG e m EE TT IT Parameter minutes The timeout time ranging from 5 to 30 in minutes The value is 10 by default Command Mode Global Configuration Mode Example Configure the timeout time of the switch as 15 minutes TL SL5428E config user idle timeout 15 line Description The line command is used to enter
86. cify NTDP Hops as 5 NTDP Interval Time as 30 minutes TL SL5428E config cluster ntdp TL SL5428E config cluster ntdp timer interval timer 30 TL SL5428E config cluster ntdp hop 5 cluster explore Description The cluster explore command is used to enable the topology information collecting function manually Syntax cluster explore Command Mode Global Configuration Mode Example Enable the topology information collecting function manually TL SL5428E config cluster explore cluster Description The cluster command is used to configure cluster functions of a specified port To return to the default configuration please use no cluster command Syntax cluster ndp disable enable ntdp disable enable no cluster Parameter ndp Enable Disable NDP function for the port By default it is enabled ntdp Enable Disable NTDP function for the port By default it is enabled Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet 243 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Example Enable NDP and NTDP function for Fast Ethernet port 5 TL SL5428E config interface fastEthernet 1 0 5 TL SL5428E config if cluster ndp enable ntdp enable cluster ip pool Description The cluster ip pool command is used to create a new cluster If no specified cluster name is set through clust
87. command is used to select the DoS Defend Type To disable the corresponding Defend Type please use no ip dos prevent type command Syntax ip dos prevent type land scan synfin xma scan null scan port less 1024 smurf blat ping flood syn flood win nuke no ip dos prevent type land scan synfin xma scan null scan port less 1024 smurf blat ping flood syn flood win nuke Parameter land Land attack scan synfin Scan SYNFIN attack xma scan Xma Scan attack null scan NULL Scan attack port less 1024 The SYN packets whose Source Port less than 1024 smurf Smurf attack blat Blat attack ping flood Ping flooding attack With the ping flood attack enabled the switch will limit automatically the forwarding speed of ping packets to 512K when attacked by ping flood syn flood SYN SYN ACK flooding attack With the syn flood attack enabled the switch will limit automatically the forwarding speed of ping packets to 512K when attacked by syn flood win nuke winNuke Attack attack Command Mode Global Configuration Mode Example Enable the DoS Defend Type named Land attack TL SL5428E config ip dos prevent type land 86 TL SL5428E BAG 6 KY LL a VET Xe DL Eli e BRETT ip dos prevent detect Description The ip dos prevent detect command is used to configure the detect time for each DoS attack type except the flooding a
88. d Once password is configured you are required to enter it to access Privileged EXEC mode 1 4 Conventions 1 4 1 Format Conventions The following conventions are used in this Guide gt Items in square brackets are optional gt Items in braces are required gt Alternative items are grouped in braces and separated by vertical bars For example speed 10 100 1000 gt Bold indicates an unalterable keyword For example show logging gt Normal Font indicates a constant several options are enumerated and only one can be selected For example switchport type access trunk general gt Italic Font indicates a variable an actual value must be assigned For example bridge aging time aging time 13 TL SL5428E BAG 6 0 5 1 KREIEN le BRETT 1 4 2 Special Characters You should pay attentions to the description below if the variable is a character string gt gt These six characters lt gt 8 can not be input If a blank is contained in a character string single or double quotation marks should be used for example hello world hello world and the words in the quotation marks will be identified as a string Otherwise the words will be identified as several strings 1 43 Parameter Format Some parameters must be entered in special formats which are shown as follows gt gt MAC Address must be enter in the format of XX XX XX XX XX XX One or several va
89. d VLAN as the community VLAN of the Private VLAN To invalid the currently community VLAN please use no private vlan community command Syntax private vlan community no private vlan community 44 TL SL5428E MOCSUCEU MIA EME Eli e BRETT Command Mode VLAN Configuration Mode VLAN Example Configure the VLAN 4 as the community VLAN of the private VLAN TL SL5428E config vlan 4 TL SL5428E config vlan Hprivate vlan community private vlan association Description The private vlan association command is used to associate primary VLAN with secondary VLAN To exterminate the currently association please use no private vlan association command Syntax private vlan association vian_list no private vlan association vian_list Parameter vlan_list Secondary VLAN ID ranging from 2 to 4049 Command Mode VLAN Configuration Mode VLAN Example Associate primary VLAN 3 with community VLAN 4 as a private VLAN TL SL5428E config vlan 3 TL SL5428E config vian private vian association 4 switchport private vlan Description The switchport private vlan command is used to configure the private VLAN mode for the switchport To invalid the configuration please use no switchport private vlan command 45 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Syntax switchport private vlan promiscuous host no switchport private vlan promiscuous host Parameter promiscuous host Configure the private
90. d ea day Sets eene ee 15 ele 16 Elle EE 16 E 16 RER 17 RI VE ele EE 17 clear IEN a cece 22h ches ces cada Set hd et nate ete did 18 Chapter 3 IEEE 802 1Q VLAN Commands ccccccccccononccccncccncncnnnananannnnnenonnnnnananans 19 Wi Asst Ae Atala Meike is Pa tN hk tal Saale al hd et aah ah Sct eis oh cated te SET ah 19 ue VIAN EE EE 20 O eet Eed 20 SWItChport MOE 2 tiie katie ded ia 21 Switchport access E In DE 21 switchport trunk allowed Vian esos beier Eeh 22 switchport general allowed van AAA 23 SWitehpOrnt PVid EE 23 Show VIM SUMMA DN cta tin dee Eu See dee dada evade bea dee dans See ad 24 Glen 24 SNOW VIAN sedate atten ee essa ew at a ends de tind Raat endear eaten A 25 Chapter 4 MAC based VLAN Commands oooocccccccccnnnoncncnnccncnnnnnnnananannnenenenennnanans 26 Maca MAC AMES deed eer Ee eene e 26 maclar anis e a a a a e a a 27 show mac vlan 00 eee eeee cence eee eee eee eee eee nn aaa eae aaa aaa aae a aae ease aaeaaaeaaae ages aaae aes aaeeaaeaeaaeneanees 27 show mac vlan Interface 28 Chapter 5 Protocol based VLAN Commands c ccssceeeesseeeeeeeseeeeeeeeeeeeeeees 29 prot colevlan TE 29 protocol vlan V AN TE 30 DrofocOk vam 30 show protocol vlan Template 31 show protocol Van MAMA ek ee ee Eh 31 show protocol vlan Interface 32 Chapter 6 VLAN VPN Commande cccccoonnnnnncnccccnnccnnnanannnnnnncnnnnnnnannnnnnnenenenennnanans 33 dotta tunnel ias e O eS 33 d tTd tunneltpid e ea idol 33 dottg tunnel Mappi
91. d is used to download a SSL key to the switch from TFTP server Syntax ip http secure server download key ss key ip address p addr Parameter ssi key The name of the SSL key which is selected to download to the switch The length of the name ranges from 1 to 25 characters The Key must be BASE64 encoded ip addr The IP address of the TFTP server Command Mode Global Configuration Mode Example Download a SSL Key named ssl key from TFTP server with the IP Address of 192 168 0 146 TL SL5428E config ip http secure server download key ssl key ip address 192 168 0 146 110 TL SL5428E MOSCA EME EG e BRETT show ip http secure server Description The show ip http secure server command is used to display the global configuration of SSL Syntax show ip http secure server Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of SSL TL SL5428E config show ip http secure server 111 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Chapter 20 MAC Address Commands MAC Address configuration can improve the network security by configuring the Port Security and maintaining the address information by managing the Address Table mac address table static Description The mac address table static command is used to add the static MAC address entry To remove the corresponding entry please use no mac address table static command The static addres
92. ddress source MAC address and port number matched to the IP MAC binding rules can be processed TL SL5428E config interface range fastEthernet 1 0 5 10 TL SL5428E config if range ip verify source sip mac 82 TL SL5428E BA 6 0 5 1 a VET Xe DL EG e BRETT show ip verify source Description The show ip verify source command is used to display the IP Verify Source configuration information Syntax show ip verify source Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the IP Verify Source configuration information TL SL5428E config show ip verify source 83 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Chapter 15 DoS Defend Command DoS Denial of Service Attack is to occupy the network bandwidth maliciously by the network attackers or the evil programs sending a lot of service requests to the Host With the DoS Defend enabled the switch can analyze the specific field of the received packets and provide the defend measures to ensure the normal working of the local network ip dos prevent Description The ip dos prevent command is used to enable the DoS defend function globally To disable the DoS defend function please use no ip dos prevent command Syntax ip dos prevent no ip dos prevent Command Mode Global Configuration Mode Example Enable the DoS defend function globally TL SL5428E config ip dos prevent ip dos prevent ping rate Description The ip do
93. ded ac id rule rule id deny permit sip source ip smask source ip mask dip destination ip dmask destination ip mask tseg time segment frag disable enable dscp dscp s port s port d port d port tcpflag tcpflag protocol protocol icmptype icmptype icmpcode icmpcode tos tos pri pri no access list extended aci id rule rule id Parameter acl id The desired Extended IP ACL for configuration rule id The rule ID deny The operation to discard packets permit The operation to forward packets It is the default value source ip The source IP address contained in the rule source ip mask The source IP address mask It is required if you typed the source IP address 171 rule TL SL5428E BAG 6 KY Te aT Te Xe EG e BRETT destination ip The destination IP address contained in the rule destination ip mask The destination IP address mask It is required if you typed the destination IP address time segment The time range for the rule to take effect By default it is not limited frag Enable Disable Fragment By default it is disabled If Fragment is enabled this rule will process all the fragments and the last piece of fragment will be always forwarded dscp Specify the dscp value ranging from O to 63 s port The source port number d port The destination port number tcpflag Specify th
94. dual Description The cluster individual command is used to specify the current switch as individual switch Syntax cluster individual Command Mode Global Configuration Mode 246 TL SL5428E Ent L A EEES e m EE ETT IT Example Specify the current switch as individual switch TL SL5428E config cluster individual cluster time segment Description The cluster time segment command is used to create time segment entry and enter cluster time segment configuration mode To delete a time segment entry please use no cluster time segment command The time segment is needed in cluster manage batch management user config auto backup command After the time segment entry is created you can use the absolute periodic and backup time command to further specify its effective time By default its effective time is 00 00 every day Syntax cluster time segment time segment name no cluster time segment time segment name Parameter time segment name Type a name for the time segment which contains 16 characters at most composing digits English letters and under dashes only Command Mode Global Configuration Mode Example Create a time segment with the name t1 TL SL5428E config cluster time segment t1 absolute Description The absolute command is used to configure a time segment into an Absolute Mode and specify modify its stat amp end date To delete the corresponding Absolute Mode time segment
95. e Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure the ingress rate as 5120Kbps and egress rate as 1024Kbps for Fast Ethernet port 5 TL SL5428E config interface fastEthernet 1 0 5 TL SL5428E config if bandwidth ingress 5120 egress 1024 clear counters Description The clear counters command is used to clear the statistic information of all the Ethernet ports Syntax clear counters Command Mode Global Configuration Mode Example Clear the statistic information of all Ethernet ports TL SL5428E config clear counters show interface status Description The show interface status command is used to display the connective status of an Ethernet port 144 TL SL5428E BA 6 KT LL a VET Xe DL EG e m EE ETT IT Syntax show interface fastEthernet port gigabitEthernet porf status Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the connective status of all Ethernet ports TL SL5428E config show interface status Display the connective status of Fast Ethernet port 1 TL SL5428E config show interface fastEthernet 1 0 1 status show interface counters Description The show interface counters command is used to display the statistic information of an Ethernet port Syntax show interface fastE
96. e Display the DHCP Snooping configuration of all Ethernet ports TL SL5428E show ip dhcp snooping interface Display the DHCP Snooping configuration of Fast Ethernet port 5 TL SL5428E show ip dhcp snooping interface fastEthernet 1 0 5 76 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Chapter 13 ARP Inspection Commands ARP Address Resolution Protocol Detect function is to protect the switch from the ARP cheating such as the Network Gateway Spoofing and Man In The Middle Attack etc ip arp inspection global Description The ip arp inspection command is used to enable the ARP Detection function globally To disable the ARP Detection function please use no ip arp detection command Syntax ip arp inspection no ip arp inspection Command Mode Global Configuration Mode Example Enable the ARP Detection function globally TL SL5428E config ip arp inspection ip arp inspection trust Description The ip arp inspection trust command is used to configure the port for which the ARP Detect function is unnecessary as the Trusted Port To clear the Trusted Port list please use no ip arp detection trust command The specific ports such as up linked port routing port and LAG port should be set as Trusted Port To ensure the normal communication of the switch please configure the ARP Trusted Port before enabling the ARP Detect function Syntax ip arp inspection trust no ip arp inspection trust 77 TL SL5428E
97. e SNMP engine on the switch Its length ranges from 10 to 64 hexadecimal characters which must be even number meanwhile remote Remote Engine ID for the switch The Engine ID is a unique alphanumeric string used to identify the SNMP engine on the remote device which receives informs from the switch Its length ranges from 10 to 64 hexadecimal characters which must be even number meanwhile Command Mode Global Configuration Mode 220 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Example Specify the local enginelD as 1234567890 and the remote enginelD as abcdef123456 TL SL5428E config snmp server enginelD local 1234567890 remote abcdef123456 snmp server traps snmp Description The snmp server traps snmp command is used to enable SNMP standard traps which include four types linkup linkdown warmstart and coldstart To disable the sending of SNMP standard traps please use no snmp server traps snmp command Syntax snmp server traps snmp linkup linkdown warmstart coldstart no snmp server traps snmp linkup linkdown warmstart coldstart Parameter linkup Enable linkup trap It is sent when port status changes from linkdown to linkup By default it is enabled linkdown Enable linkdown trap It is sent when port status changes from linkup to linkdown By default it is enabled warmstart Enable warmstart trap It is sent upon SNMP function reboot By default it is e
98. e SSH v2 TL SL5428E config ip ssh version v2 ip ssh timeout Description The ip ssh timeout command is used to specify the idle timeout time of SSH To restore to the factory defaults please use ip ssh timeout command Syntax ip ssh timeout value no ip ssh timeout Parameter value The ldle timeout time During this period the system will automatically release the connection if there is no operation from the client It ranges from 1 to 120 in seconds By default this value is 120 Command Mode Global Configuration Mode Example Specify the idle timeout time of SSH as 100 seconds TL SL5428E config ip ssh timeout 100 ip ssh max client Description The ip ssh max client command is used to specify the maximum number of the connections to the SSH server To return to the default configuration please use no ip ssh max client command Syntax ip ssh max client num no ip ssh max client Parameter num The maximum number of the connections to the SSH server It ranges from 1 to 5 By default this value is 5 106 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Command Mode Global Configuration Mode Example Specify the maximum number of the connections to the SSH server as 3 TL SL5428E config ip ssh max client 3 ip ssh download Description The ip ssh download command is used to download the SSH key file from TFTP server Syntax ip ssh download v1 v2 key file ip addre
99. e aging time and can only be deleted manually too However the learned entries will be saved even the switch is rebooted status Enable or disable the Port Security function for a specified port By default this function is disabled Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable Port Security function for Fast Ethernet port 1 select Static mode as the learn mode and specify the maximum number of MAC addresses that can be learned on this port as 30 TL SL5428E config interface fastEthernet 1 0 1 TL SL5428E config if mac address table max mac count max number 30 mode static status enable show mac address table Description The show mac address table command is used to display the information of all address entries Syntax show mac address table dynamic static drop all Parameter dynamic static drop all The type of your desired entry Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of all Address entries TL SL5428E config show mac address table all 115 TL SL5428E MOSUCEU MIA EEES e BRETT show mac address table aging time Description The show mac address table aging time command is used to display the Aging Time of the MAC address Syntax show mac address table aging time Command Mode Privileged EXEC
100. e flag value when using TCP protocol protocol Configure the value of the matching protocol icmptype Configure the predefined ICMP type icmpcode Configure the predefined ICMP code tos Enter the IP ToS contained in the rule pri Enter the IP Precedence contained in the rule Command Mode Global Configuration Mode Example Create an Extended IP ACL whose ID is 220 and add Rule 10 for it In the rule the source IP address is 192 168 0 100 the source IP address mask is 255 255 255 0 the time range for the rule to take effect is tSeg1 and the packets match this rule will be forwarded by the switch TL SL5428E config access list create 220 TL SL5428E config access list extended 220 rule 10 permit sip 192 168 0 100 smask 255 255 255 0 tseg tSeg1 Description The rule command is used to configure MAC ACL rule To delete the corresponding rule please use no rule command 172 TL SL5428E BAG 6 0 5 1 KREIEN le BRETT rule rule id deny permit smac source mac smask source mac mask dmac destination mac dmask destination mac mask vid vian id type ethernet type pri user pri tseg time segmentf no rule rule id Parameter rule id The rule ID deny The operation to discard packets permit The operation to forward packets By default it is permit source mac The source MAC address contained in the rule source mac mask T
101. e from the router port it will consider this port is not a router port any more Router Port Time ranges from 60 to 600 in seconds By default it is 300 member time Member Port Time Within this time if the switch does not receive IGMP report message from the member port it will consider this port is not a member port any more Member Port Time ranges from 60 to 600 in seconds By default it is 260 202 TL SL5428E BAS 0 5 1 a VET Xe DL EG e BRETT leave time Leave Time which is the interval between the switch receiving a leave message from a host and the switch removing the host from the multicast groups Leave Time ranges from 1 to 30 in seconds By default it is 1 port Static Router Port which is mainly used in the network with stable topology There are two types of port Fast Ethernet port ranging from 1 to 24 in the format of 1 0 2 Gigabit Ethernet port ranging from 25 to 28 in the format of 1 0 25 Command Mode Global Configuration Mode Example Enable Multicast VLAN 3 and configure Router Port Time as 100 seconds TL SL5428E config ip igmp snooping multi vlan config 3 rtime 100 ip igmp snooping filter add id Description The ip igmp snooping filter add id command is used to configure the multicast IP range desired to filter To delete the corresponding IP range please use no ip igmp snooping filter add id command When IGMP Snooping is enabled you can specified the multicast IP ra
102. e general TL SL5428E config if switchport general allowed vlan 2 tagged switchport pvid Description The switchport pvid command is used to configure the PVID for the switch ports 23 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Syntax switchport pvid vian id Parameter vlan id Specify IEEE 802 1Q VLAN ID ranging from 1 to 4094 Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Specify the PVID of Fast Ethernet port 3 as 1 TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if switchport pvid 1 show vlan summary Description The show vlan summary command is used to display the summarized information of IEEE 802 1Q VLAN Syntax show vlan summary Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the summarized information of IEEE 802 1Q VLAN TL SL5428E config show vlan summary show vlan brief Description The show vlan brief command is used to display the brief information of IEEE 802 10 VLAN 24 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Syntax show vlan brief Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the brief information of IEEE 802 1Q VLAN TL SL5428E config show vlan brief show vlan Description The show vlan command is used
103. e gigabitEthernet Example Enable the broadcast control function for Fast Ethernet port 5 TL SL5428E config interface fastEthernet 1 0 5 TL SL5428E config if storm control broadcast storm control multicast Description The storm control multicast command is used to enable the multicast control function To disable the multicast control function please use no storm control multicast command Multicast control function allows the switch to filter multicast in the network If the transmission rate of the multicast packets exceeds the set bandwidth the packets will be automatically discarded to avoid network broadcast storm Syntax storm control multicast rate rate no storm control multicast Parameter rate Select the bandwidth for receiving multicast packets on the port The packet traffic exceeding the bandwidth will be discarded By default the value is 128K Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the multicast control function for Fast Ethernet port 5 TL SL5428E config interface fastEthernet 1 0 5 142 TL SL5428E MOCSUCEU MIA EME EG e BRETT TL SL5428E config if storm control multicast storm control unicast Description The storm control unicast command is used to enbale the unicast control function To disable the unicast control function please us
104. e no storm control unicast command Unicast control function allows the switch to filter UL frame in the network If the transmission rate of the UL frames exceeds the set bandwidth the packets will be automatically discarded to avoid network broadcast storm Syntax storm control unicast rate rate no storm control unicast Parameter rate Select the bandwidth for receiving UL Frame on the port The packet traffic exceeding the bandwidth will be discarded By default the value is 128K Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the unicast control function for Fast Ethernet port 5 TL SL5428E config interface fastEthernet 1 0 5 TL SL5428E config if storm control unicast bandwidth Description The bandwidth command is used to configure the bandwidth limit for an Ethernet port To disable the bandwidth limit please use no bandwidth command Syntax bandwidth ingress ingress rate egress egress rate 143 TL SL5428E BA 6 0 5 1 a EEES e M EE ETT IT no bandwidth all ingress egress Parameter ingress rate Specify the bandwidth for receiving packets Range 1 102400 for the megaport 1 1024000 for the gigaport egress rate Specify the bandwidth for sending packets Range 1 102400 for the megaport 1 1024000 for the gigaport Command Mod
105. e triggered if the sampled value is lower than the Falling Threshold It ranges from 1 to 12 a type Alarm Type with rise fall and all options Rise indicates that the alarm event will be triggered when the sampled value exceeds the Rising Threshold fall indicates that the alarm event will be triggered when the sampled value is under the Falling Threshold and all indicates that the alarm event will be 227 TL SLSA7pERIGCEIORRKR EIET DL EG e BRETT triggered either the sampled value exceeds the Rising Threshold or is under the Falling Threshold By default the Alarm Type is all owner name The owner of the entry ranging from 1 to 16 characters By default it is monitor interval The alarm interval time ranging from 10 to 3600 in seconds By default it is 1800 Command Mode Global Configuration Mode Example Configure the ports of entries of 1 3 as Gi1 0 2 the owners as owner1 and the alarm intervals as 100 seconds TL SL5428E config rmon alarm 1 3 interface fastEthernet 1 0 2 owner owner interval 100 show snmp server Description The show snmp server command is used to display SNMP configuration globally Syntax show snmp server Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display SNMP configuration globally TL SL5428E show snmp server show snmp server view Description The show snmp server view command is used to display the View table Sy
106. emoving the host from the multicast groups Leave Time ranges from 1 to 30 in seconds By default it is 1 port Static Router Port which is mainly used in the network with stable topology There are two types of port Fast Ethernet port ranging from 1 to 24 in 201 TL SL5428E BA 6 0 5 1 Wa EME EG e BRETT the format of 1 0 2 Gigabit Ethernet port ranging from 1 4 in the format of 1 0 2 vian id The VLAN ID of the multicast IP ranging from 1 to 4094 ip The static multicast IP address port list The forward port list of the multicast group Command Mode Global Configuration Mode Example Enable the IGMP Snooping function and modify Member Port Time as 200 seconds for VLAN1 3 TL SL5428E config ip igmp snooping vlan config 1 3 mtime 200 ip igmp snooping multi vlan config Description The ip igmp snooping multi vlan config command is used to create and configure a Multicast VLAN To delete the corresponding Multicast VLAN please use no ip igmp snooping multi vlan config command Syntax ip igmp snooping multi vlan config vlan id rtime router time mtime member time Itime eave time rport interface fastEthernet port gigabitEthernet port no ip igmp snooping multi vlan config Parameter vlan id The ID of the VLAN desired to modify configuration ranging from 2 to 4094 router time Router Port Time Within this time if the switch does not receive IGMP query messag
107. eout command Syntax dot1x timeout quiet period time reauth period time no dot1x timeout quiet period reauth period Parameter quiet period time The value for Quiet Period ranging from 1 to 999 in seconds By default it is 10 Once the supplicant failed to the 802 1X Authentication then the switch will not respond to the authentication request from the same supplicant during the Quiet Period reauth period time The maximum time for the switch to wait for the response from supplicant before resending a request to the supplicant ranging from 1 to 9 in second By default it is 3 91 TL SL5428E MOCSUCEU MIA EME Eli e BRETT Command Mode Global Configuration Mode Example Configure the quiet period as 100 seconds TL SL5428E config dot1x timeout quiet period 100 dot1x max reauth req Description The dot1x max reauth req command is used to configure the maximum transfer times of the repeated authentication request when the server cannot be connected To restore to the default value please use no dot1x max reauth req command Syntax dot1x max reauth req times no dot1x max reauth req Parameter times The maximum transfer times of the repeated authentication request ranging from 1 to 9 in times By default the value is 3 Command Mode Global Configuration Mode Example Configure the maximum transfer times of the repeated authentication request as 5 TL SL5428E config dot1x ma
108. er commander command the newly created cluster will enjoy the system default name tplink cluster Syntax cluster ip pool p mask Parameter ip The cluster IP address pool mask The cluster IP address mask Command Mode Global Configuration Mode Example Create a cluster and configure its IP address pool as 192 168 10 1 192 168 0 254 TL SL5428E config cluster ip pool 192 168 10 1 255 255 255 0 cluster commander Description The cluster commander command is used to specify the cluster name and you can only specify the cluster name when you create the cluster To delete a cluster please use no cluster commander command Syntax cluster commander name no cluster commander Parameter name The cluster name ranging from 1 to 16 characters 244 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Command Mode Global Configuration Mode Example Configure the newly created cluster name as tp TL SL5428E config cluster commander tp cluster manage Description The cluster manage command is used to configure the hold time and interval to send handshake packets of the cluster To return to the default configuration please use no cluster manage command Syntax cluster manage holdtime hold time timer interval time no cluster manage holdtime timer Parameter hold time Hold Time which is the time for the switch to keep the cluster information Hold Time ranges from 1
109. erface gigabitEthernet interface range gigabitEthernet Example Add a description Port 5 to Fast Ethernet port 5 TL SL5428E config interface fastEthernet 1 0 5 TL SL5428E config if description Port 5 138 TL SL5428E BAG 6 0 5 1 a EEN EG e BRETT shutdown Description The shutdown command is used to disable an Ethernet port To enable this port again please use no shutdown command Syntax shutdown no shutdown Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Disable Gigabit Ethernet port 25 TL SL5428E config interface gigabitEthernet 1 0 25 TL SL5428E config if shutdown flow control Description The flow control command is used to enable the flow control function for a port To disable the flow control function for this corresponding port please use no flow control command With the flow control function enabled the Ingress Rate and Egress Rate can be synchronized to avoid packet loss in the network Syntax flow control no flow control Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the flow control function for Gigabit Ethernet port 25 TL SL5428E config interface gigabitEthernet 1 0 25 TL SL5428E config if flow control 139 TL SL5428E
110. erity level There are 8 severity levels marked with values 0 7 The information of levels with priority not lower than the select level will display Display all the log information in the log file by default Command Mode Privileged EXEC Mode and Any Configuration Mode 103 TL SL5428E BAG 6 KY Ts a Tate D EC Oe BRETT E Example Display the log information with the level marked 0 3 in the log file TL SL5428E config show logging flash level 3 104 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Chapter 18 SSH Commands SSH Security Shell can provide the unsecured remote management with security and powerful authentication to ensure the security of the management information ip ssh server Description The ip ssh server command is used to enable SSH function To disable the SSH function please use no ip ssh server command Syntax ip ssh server no ip ssh server Command Mode Global Configuration Mode Example Enable the SSH function TL SL5428E config ip ssh server ip ssh version Description The ip ssh version command is used to enable the SSH protocol version To disable the protocol version please use no ip ssh version command Syntax ip ssh version v1 v2 no ip ssh version v1 v2 Parameter vi v2 The SSH protocol version to be enabled They represent SSH vi and SSH v2 respectively Command Mode Global Configuration Mode 105 TL SL5428E MOSCA EME EG e M EE ETT IT Example Enabl
111. ernet User Guidelines Port priority is one property of the port When the port priority is specified the data will be classified into the egress queue based on the CoS value of the ingress port and the mapping relation between the CoS and TC in IEEE 802 1P Example Configure the priority of port 5 as 3 TL SL5428E config interface gigabitEthernet 1 0 5 TL SL5428E config if qos 3 qos cos Description The qos cos command is used to enable the mapping relation between IEEE802 1P Priority and TC egress queue To disable the mapping relation please use no qos cos command 149 TL SL5428E BAG 6 0 5 1 aE TATT DL EG e M EE ETT IT Syntax qos cos no qos cos Command Mode Global Configuration Mode User Guidelines IEEE 802 1P gives the Pri field in IEEE 802 1Q tag a recommended definition When the mapping relation between IEEE 802 1P Priority and TC egress queue is enabled the data will be classified into the egress queue based on this mapping relation Example Enable the mapping relation between IEEE 802 1P Priority and egress queue TL SL5428E config qos cos qos dscp Description The qos dscp command is used to enable the mapping relation between DSCP Priority and TC egress queue To disable the mapping relation please use no qos dscp command Syntax qos dscp no qos dscp Command Mode Global Configuration Mode User Guidelines DSCP DiffServ Code Point is a new definition to IP ToS field given
112. et port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the neighbor information of Fast Ethernet port 1 TL SL5428E show lldp neighbor information interface fastEthernet 1 0 1 show Ildp traffic interface Description The show Ildp traffic interface command is used to display the LLDP statistic information between the local device and neighbor device of the corresponding port By default the LLDP statistic information of all the ports will be displayed Syntax show lldp traffic interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number 239 TL SLS4A7pERIGOCEIKROEIET D EC Oe BRETT E Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LLDP statistic information of Fast Ethernet port 1 TL SL5428E show Ildp traffic interface fastEthernet 1 0 1 240 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Chapter 32 Cluster Commande Cluster Management function enables a network administrator to manage the scattered devices in the network via a management device After a commander switch is configured management and maintenance operations intended for the member devices in a cluster is implemented by the commander device cluster ndp Description The cluster ndp command is used to configure NDP globally To return to the default configuration please use no cluster ndp command NDP Neig
113. eter password Configure the connection password which contains 16 characters at most composing digits English letters and under dashes only Command Mode Line Configuration Mode Example Configure the connection password of Console port connection 0 as tplink TL SL5428E config line console 0 TL SL5428E config line fpassword tplink Configure the connection password of virtual terminal connection 0 5 as tplink TL SL5428E config line vty 0 5 TL SL5428E config line fpassword tplink login Description The login command is used to configure the login of a switch not to use the user name and password At this situation a connection password must be set for virtual terminal connection 63 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Syntax login Command Mode Line Configuration Mode Example Configure the login of Console port connection 0 as login mode TL SL5428E config line console 0 TL SL5428E config line login Configure the login of virtual terminal connection 0 5 as login mode TL SL5428E config line vty 0 5 TL SL5428E config line login login local Description The login local command is used to configure the login of a switch with the user name and password Syntax login local Command Mode Line Configuration Mode Example Configure the login of virtual terminal connection 0 5 as login local mode TL SL5428E config line vty 0 5 TL SL5428E config l
114. evel of SNMP v3 Group There are three options including noAuthNoPriv no authorization and no encryption authNoPriv authorization and no encryption and authPriv authorization and encryption By default the option is noAuthNoPriv The Security Level of the User must be the same with that of the Group which the User belongs to cmode The Authentication Mode of the SNMP v3 User with none MD5 and SHA options None indicates no authentication method is used MD indicates the port authentication is performed via HMAC MD5 algorithm and SHA indicates the port authentication is performed via SHA Secure Hash Algorithm SHA authentication mode has a higher security than MD5 mode By default the Authentication Mode is none confirm pwd Authentication Password ranging from 1 to 16 characters emode The Privacy Mode of the SNMP v3 User with none and DES options None indicates no privacy method is used and DES indicates DES encryption method is used By default the Privacy Mode is none encrypt pwd Privacy Password ranging from 1 to 16 characters Command Mode Global Configuration Mode 217 TL SL5428E Ent L A EEES e m EE ETT IT Example Add Local User admin to Group group2 and configure the Security Model of the user as v3 the Security Level of the group as authPriv the Authentication Mode of the user as MD5 the Authentication Password
115. ex r event falling threshold f hold falling event index f event a type rise fall all owner owner name interval interval no rmon alarm index Parameter index The index number of the Alarm Management entry ranging from 1 to 12 in the format of 1 3 5 port String for the port on which the Alarm entry acts format as module slot port for example 1 0 24 alarm variable The alarm variable By default the option is drop s type Sample Type which is the sampling method for the selected variable and comparing the value against the thresholds There are two options absolute and delta Absolute indicates comparing the values directly with the thresholds at the end of the sampling interval Delta indicates subtracting the last sampled value from the current value and then comparing the difference in the values with the threshold By default the Sample Type is absolute r hold The rising counter value that triggers the Rising Threshold alarm ranging from 1 to 65535 By default it is 100 r event Rise Event which is the index of the corresponding event which will be triggered if the sampled value is larger than the Rising Threshold It ranges from 1 to 12 f hold The falling counter value that triggers the Falling Threshold alarm ranging from 1 to 65535 By default it is 100 f event Fall Event which is the index of the corresponding event which will b
116. f the RADIUS authentication server TL SL5428E config show radius authentication 98 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Chapter 17 System Log Commands The log information will record the settings and operation of the switch respectively for you to monitor operation status and diagnose malfunction logging buffer Description The logging buffer command is used to configure the severity level and the status of the configuration input to the log buffer To return to the default configuration please use no logging buffer command Local Log is the log information saved in the switch It has two output channels that is it can be saved to two different positions log buffer and log file The log buffer indicates the RAM for saving system log and the information in the log buffer can be got by show logging buffer command It will be lost when the switch is restarted Syntax logging buffer evel no logging buffer Parameter level Severity level of the log information output to each channel There are 8 severity levels marked with values 0 7 The smaller value has the higher priority Only the log with the same or smaller severity level value will be output By default it is 7 indicating that all the log information will be saved in the log buffer Command Mode Global Configuration Mode Example Set the severity level as 6 TL SL5428E config logging buffer 6 99 TL SL5428E MOCSUCEU MIA EME EG e M
117. fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the Protocol based VLAN feature for the Gigabit Ethernet port 25 TL SL5428E config interface gigabitEthernet 1 0 25 TL SL5428E config if Hprotocol vlan show protocol vlan template Description The show protocol vlan template command is used to display the information of the Protocol based VLAN templates Syntax show protocol vlan template Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of the Protocol based VLAN templates TL SL5428E config show protocol vlan template show protocol vlan vlan Description The show protocol vlan vlan command is used to display the information about Protocol based VLAN entry 31 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Syntax show protocol vlan vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display information of the Protocol based VLAN entry TL SL5428E config show protocol vlan vian show protocol vlan interface Description The show protocol vlan interface command is used to display port state and of Protocol based VLAN interface Syntax show protocol vlan interface Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the port state and of Protocol based VLAN interface TL SL5428E config show protocol vlan interface
118. fault the registration mode is normal Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEhternet Example Configure the GVRP registration mode as fixed for Fast Ethernet ports 2 6 TL SL5428E config interface range fastEthernet 1 0 2 6 TL SL5428E config if range gvrp registration fixed 50 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT gvrp timer Description The gvrp timer command is used to set a GVRP timer for the desired port To restore to the default setting of a GARP timer please use no gvrp timer command Syntax gvrp timer leaveall join leave value no gvrp timer leaveall join leave Parameter leaveall join leave They are the three timers leave All join and leave Once the LeaveAll Timer is set the port with GVRP enabled can send a LeaveAll message after the timer times out so that other GARP ports can re register all the attribute information After that the LeaveAll timer will start to begin a new cycle To guarantee the transmission of the Join messages a GARP port sends each Join message two times The Join Timer is used to define the interval between the two sending operations of each Join message Once the Leave Timer is set the GARP port receiving a Leave message will start its Leave timer and deregister the attribute information if it does not receive a
119. fig show mac address table interface fastEthernet 1 0 1 show mac address table count Description The show mac address table count command is used to display the total amount of MAC address table Syntax show mac address table count Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the total amount of MAC address table TL SL5428E config show mac address table count show mac address table address Description The show mac address table address command is used to display the information of a specified MAC address 117 TL SL5428E BA Si KT LL a EME Eli e BRETT Syntax show mac address table address mac addr Parameter mac addr The specified MAC address Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of the MAC address 00 00 00 00 23 00 00 TL SL5428E config show mac address table 00 00 00 00 23 00 00 show mac address table vlan Description The show mac address table vlan command is used to display the MAC address configuration of the specified vlan Syntax show mac address table vlan vid Parameter vid The specified VLAN id Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the MAC address configuration of vlan 1 TL SL5428E config show mac address table vlan 1 118 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Chapter 21 System Configuration Commands System C
120. figuration including the enable disable status and the Trusted Port list Syntax show ip arp inspection Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the ARP detection configuration globally TL SL5428E config show ip arp inspection show ip arp inspection interface Description The show ip arp inspection interface command is used to display the interface configuration of ARP detection Syntax show ip arp inspection interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of Fast Ethernet port 1 80 TL SL5428E MOSCA EME EG e BRETT TL SL5428E config show ip arp inspection interface fastEthernet 1 0 1 Display the configuration of all Ethernet ports TL SL5428E config show ip arp inspection interface show ip arp inspection statistics Description The show ip arp inspection statistics command is used to display the number of the illegal ARP packets received Syntax show ip arp inspection statistics Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the number of the illegal ARP packets received TL SL5428E config show ip arp inspection statistics clear ip arp inspection statistics Description The clear ip arp inspection statistics command is used to clear the statistic of the illegal ARP pac
121. gh Console port connection and then you are in User EXEC Mode TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide e Telnet 192 168 0 1 fx Password TL SLS428E gt Figure 1 13 Enter into the User EXEC Mode 3 When entering enable command to access Privileged EXEC Mode you are required to give the password 123 you have set through Console port connection cir Telnet 192 168 0 1 Password TL SLS428E gt enable Password TL SL5428EHt Figure 1 14 Enter into the Privileged EXEC Mode Now you can manage your switch with CLI commands through Telnet connection Note You can refer to Chapter 11 User Manage Commands for detailed commands information of the Telnet connection configuration 1 2 CLI Command Modes The CLI is divided into different command modes User EXEC Mode Privileged EXEC Mode Global Configuration Mode Interface Configuration Mode and VLAN Database VLAN Configuration Mode Interface Configuration Mode can also be divided into Interface fastEthernet Interface gigabitEthernet Interface link aggregation and some other modes which is shown as the following diagram 10 TL SL5428E RIIT MIA EME Eli e M EE ETT IT Interface Configuration Mode Interface fastEthernet Interface gigabitEthernet Interface link aggregation Interface range fastEthernet User EXEC Mode ae Interface range gigabitEthernet Interface range link aggregation
122. hapter 24 Port Mirror COMMANAS ccoooonnnnnnnnccccncnnnnnonnnnnnnncnnnnnnnnnannnnnnnnnnnnnnnnanas 156 monitor session destination interface cccccecccceceeeeeeeeeeeaeeeeeeeeeeeeeneaeeeeeeeeeeesenseeeeteeeees 156 monitor session source Interface 157 Show monitor SCSSION E 158 Chapter 25 Port isolation Commands oooonnnnnnncccccconononnnnnnnnnenonennnnanannnnnnnnnnnnnnnnns 159 POSO Oi ti cial 159 show port Ieolaton nn nr nnnrnnnnnnes 160 Chapter 26 Loopback Detection COMMANdOS ooonncccconcnncccnnncnnncnnnnnnncnnnnnnnnnnnnnanans 161 loopback detection global ococociinocococccnncoccnoncononcnnnnnononnnnnonnnnnonononnonnnnncncnnnnnnnnnnnnnnnncnnnno 161 loopback detection interval coocccnccnnnononenonononononenononononnnnnncnnnnnnnnnnnonnnenenennnenaneneneninnn 161 loopback detection recovery time eeeeeeeeeeeeeeeeee teer eeeeteserseetsertseetserttsreseernsetesetseenesensne 162 loopback detection interface cccccccceceeeeeeeeeeeceeeeeeeeeeeeeeeaeeeeeeeeeeeceeeeeeeeeeesesenseeeeeeeeess 162 loopback detection Config ttnt tre Ett EEE EEES ESEE EEEE EEES Rarere E EEEn E nene 163 loopback detection recover A 164 show loopback detection global ooooooccccccccccccccocconcnoncnononono nono nono nono nono nn nono nn nn nono no nono nnnnnnnnnnnos 164 show loopback detection Interface 165 Chapter 27 ACL COMMANdOS coooonnnnnncccccncncnonannnnnncncnnnnnnnnannnnnnnnnnnennnnnanannnnnrenrrrnnnnns 166
123. hbor Discovery Protocol is used to discover the information of the directly connected neighbor devices to support cluster establishing An NDP enabled device sends NDP packets regularly to neighbor devices as well as receives NDP packets from neighbor devices An NDP packet carries the aging time which indicates the period of the receiving devices to keep the NDP packet Syntax cluster ndp cluster ndp timer hello hello time aging aging time y no cluster ndp no cluster ndp timer hello hello time aging aging time Parameter hello time Hello Time which is the interval to send NDP packets Hello Time ranges from 5 to 254 in seconds By default it is 60 Hello Time should be smaller than Aging Time aging time Aging Time which is the period for the neighbor switch to keep the NDP packets from this switch Aging Time ranges from 5 to 255 in seconds By default it is 180 Command Mode Global Configuration Mode Example Enable NDP function globally and configure Aging Time as 120 seconds Hello Time as 50 seconds 241 TL SL5428E ENIS KY LLE A EME EG e BRETT TL SL5428E config cluster ndp TL SL5428E config cluster ndp timer hello 50 aging 120 cluster ntdp Description The cluster ntdp command is used to configure NTDP globally To return to the default configuration please use no cluster ntdp command NTDP Neighbor Topology Discovery Protocol is used to collect the NDP information a
124. he IGMP Snooping Querier function of the VLAN s To disable the IGMP Snooping Querier function of certain VLANs please use no ip igmp snooping querier vlan command to disable the IGMP Snooping Querier function of all VLANs please use no ip igmp snooping querier command Syntax ip igmp snooping querier vlan van Jet no ip igmp snooping querier vlan vian list Parameter vlan list VLAN ID list ranging from 1 to 4094 in the format of 1 3 5 It is multi optional Command Mode Global Configuration Mode Example Enable the IGMP Snooping Querier function of VLAN 1 3 TL SL5428E config ip igmp snooping querier vlan 1 3 206 TL SL5428E BA 6 0 5 1 MIA EME Eli e BRETT ip igmp snooping querier vlan general query Description The ip igmp snooping querier vlan command is used to configure the parameters for IGMP Snooping Querier to send a general query frame To return to the default configuration please use no ip igmp snooping querier vlan command Syntax ip igmp snooping querier vlan vian list query interval interval max response time response time general query source ip p addr no ip igmp snooping querier vlan vian list query interval max response time general query source ip Parameter vian list VLAN ID list ranging from 1 to 4094 in the format of 1 3 5 It is multi optional intervat The time interval to send a general query frame by IGMP Snooping Querier ranging f
125. he configuration file with the filename TL SL5428E TL SL5428E config cluster manage batch management user config restore index 1 filename TL SL5428E cluster manage batch management user config auto backup Description The cluster manage batch management user config auto backup command is used to backup the configuration to TFTP server according to the related time segment automatically To auto backup the switch you should define a time segment with the cluster time segment command first Syntax cluster manage batch management user config auto backup index index timeseg time segment name Parameter index Specify the index of the desired switch in cluster it ranges from 0 to 31 time segment name The time segment for the auto backup rule to take effect Command Mode Global Configuration Mode 251 TL SL5428E Ent L A EEES e m EE ETT IT Example Auto backup the switch with the index 1 to the TFTP server and specify its effective time as t1 TL SL5428E config cluster manage batch management user config auto backup index 1 timeseg t1 cluster manage batch management cancel Description The cluster manage batch management cancel command is used to cancel the auto backup operation of the desired switch Syntax cluster manage batch management cancle index index Parameter index Specify the index of the desired switch in cluster it ranges from 0 to 31 Command Mode Global Co
126. he queues inside WRR group follow the WRR mode In SP WRR mode TC3 is the SP group TCO TC1 and TC2 belong to the WRR group and the weight value ratio of TCO TC1 and TC2 is 1 2 4 In this way when scheduling queues the switch allows TC3 to occupy the whole bandwidth following the SP mode and the TCO TC1 and TC2 in the WRR group will take up the bandwidth according to their ratio 1 2 4 equ Equal Mode In this mode all the queues occupy the bandwidth equally The weight value ratio of all the queues is 1 1 1 1 Command Mode Global Configuration Mode Example Specify the Schedule Mode as Weight Round Robin Mode TL SL5428E config qos queue mode wrr show qos interface Description The show qos interface command is used to display the configuration of QoS based on port priority 153 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Syntax show qos interface fastEthernet port gigabitEthernet port range fastEthernet port list range gigabitEthernet port list Parameter port The Fast Gigabit Ethernet port number port list The list of Ethernet ports Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of QoS for Fast Ethernet port 5 TL SL5428E show qos interface fastEthernet 1 0 5 Display the configuration of QoS for Fast Ethernet ports 7 to 16 TL SL5428E show qos interface range fastEthernet 1 0 7 16 show qos cos map Description The
127. he source MAC address mask It is required if you typed the source MAC address destination mac The destination MAC address contained in the rule destination mac mask The destination MAC address mask It is required if you typed the destination MAC address vlan id The VLAN ID contained in the rule ranging from 1 to 4094 ethernet type EtherType contained in the rule in the format of 4 hex number user pri The user priority contained in the rule ranging from O to 7 By default it is not limited time segment The time range for the rule to take effect By default it is not limited Command Mode Mac Access list Configuration Mode Example Create a MAC ACL whose ID is 20 and add Rule 10 for it In the rule the source MAC address is 00 01 3F 48 16 23 the source MAC address mask is 11 11 11 11 11 00 VLAN ID is 2 the user priority is 5 the time range for the rule to take effect is tSeg1 and the packets match this rule will be forwarded by the switch TL SL5428E config mac access list 20 TL SL5428E config mac acl rule 10 permit smac 00 01 3F 48 16 23 smask 11 11 11 11 11 00 vid 2 pri 5 tseg tSeg1 173 TL SL5428E MOSCA EV Xe DL Eli e BRETT access list policy name Description The access list policy name command is used to add Policy To delete the corresponding Policy please use no access list policy name command A Policy is used to control the data packets
128. hops the test data can pass though It ranges from 1 to 30 By default this value is 4 Command Mode User EXEC Mode and Privileged EXEC Mode Example Test the connectivity between the switch and the network device with the IP 192 168 0 131 If the destination device has not been found after 20 maxHops 131 TL SL5428E ENSKT LLE A EEES e BRETT the connection between the switch and the destination device is failed to establish TL SL5428E tracert 192 168 0 131 h 20 loopback interface Description The loopback interface command is used to test whether the port is available or not Syntax loopback interface fastEthernet port gigabitEthernet port internal external Parameter port The Fast Gigabit Ethernet port number internal external Loopback Type There are two options internal and external Command Mode User EXEC Mode and Privileged EXEC Mode Example Do an internal type loopback test for Gigabit Ethernet port 25 TL SL5428E loopback interface gigabitEthernet 1 0 25 internal Do an external type loopback test for Gigabit Ethernet port 25 TL SL5428E loopback interface gigabitEthernet 1 0 25 external show system time Description The show system time command is used to display the current time system and its source Syntax show system time 132 TL SL5428E BA 6 KY LL a EME EG e m EE TT IT Command Mode Privileged EXEC Mode and Any Configuration Mode
129. how ip igmp snooping multi vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Multicast VLAN configuration TL SL5428E show ip igmp snooping multi vlan 210 TL SLSA7pERIGCEIORRKR EIET DL Eli e BRETT show ip igmp snooping groups Description The show ip igmp snooping groups command is used to display the information of all IGMP snooping groups It can be extended to some other commands to display the dynamic and static multicast information of a selected VALN Syntax show ip igmp snooping groups vlan vian id count dynamic dynamic count static static count Parameter vian id The VLAN ID selected to display the information of all multicast items count The numbers of all multicast groups dynamic Display dynamic multicast groups dynamic count The numbers of all dynamic multicast groups static Display static multicast groups static count The numbers of all static multicast groups Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of all IGMP snooping groups TL SL5428E show ip igmp snooping groups Display all the multicast entries in VLAN 5 TL SL5428E config show ip igmp snooping groups vlan 5 Display the count of multicast entries in VLAN 5 TL SL5428E config show ip igmp snooping groups vlan 5 count show ip igmp snooping filter Description The show ip igmp snooping filter c
130. how voice vlan switchport command is used to display the configuration information of all the ports or one specified port in the Voice VLAN Syntax show voice vlan switchport fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number selected to display the configuration information Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of Fast Ethernet port 1 in the Voice VLAN TL SL5428E config show voice vlan switchport fastEthernet 1 0 1 Display the configuration information of all the ports in the Voice VLAN TL SL5428E config show voice vlan switchport 43 TL SL5428E MOSCA EME EG e M EE ETT IT Chapter 8 Private VLAN Commands Private VLANs are configured specially for saving VLAN resource of uplink devices and decreasing broadcast private vlan primary Description The private vlan primary command is used to configure the designated VLAN as the primary VLAN of the Private VLAN To abolish the currently primary VLAN please use no private vlan primary command Syntax private vlan primary no private vlan primary Command Mode VLAN Configuration Mode VLAN Example Configure the VLAN 3 as the primary VLAN of the private VLAN TL SL5428E config vlan 3 TL SL5428E config vlan Hprivate vlan primary private vlan community Description The private vlan community command is used to configure the designate
131. ice VLAN OUI please use no voice vlan mac address command Syntax voice vlan mac address mac addr mask mask description descript no voice vlan mac address mac addr Parameter mac addr The OUI address of the voice device in the format of XX XX XX XX XX XX mask The OUI address mask of the voice device in the format of XX XX XX XX XX XX descript Give a description to the OUI for identification which contains 16 characters at most Command Mode Global Configuration Mode Example Create a Voice VLAN OUI described as TP Phone with the OUI address 00 11 11 11 11 11 and the mask address FF FF FF 00 00 00 TL SL5428E config voice vlan mac address 00 11 11 11 11 11 mask FF FF FF 00 00 00 description TP Phone switchport voice vlan mode Description The switchport voice vlan mode command is used to configure the Voice VLAN mode for the Ethernet port Syntax switchport voice vlan mode manual auto 40 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Parameter manual auto Port mode Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure the Fast Ethernet port 3 to operate in the auto voice VLAN mode TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if switchport voice vlan mode auto switchport voice vian security Descripti
132. ide information about how to use the CLI CLI Command Modes Security Levels and some Conventions Chapter 2 User Interface Provide information about the commands used to switch between five CLI Command Modes Chapter 3 IEEE 802 1Q VLAN Commands Provide information about the commands used for configuring IEEE 802 1Q VLAN Chapter 4 MAC based VLAN Commands Provide information about the commands used for configuring MAC Based VLAN Chapter 5 Protocol based VLAN Commands Provide information about the commands used for configuring Protocol based VLAN Chapter 6 VLAN VPN Commands Provide information about the commands used for configuring VLAN VPN Virtual Private Network function Chapter 7 Voice VLAN Commands Provide information about the commands used for configuring Voice VLAN Chapter 8 Private VLAN Commands Provide information about the commands used for configuring Private VLAN Chapter 9 GVRP Commands Provide information about the commands used for configuring GVRP GARP VLAN registration protocol Chapter 10 EtherChannel Commands Provide information about the commands used for configuring LAG Link Aggregation Group and LACP Link Aggregation Control Protocol Chapter 11 User Manage Commands Provide information about the commands used for user management TL SLSA7pERIGCEIOR KREIEN le BRETT Chapter 12 Binding Table Commands Provide information about the commands used for binding the IP address MA
133. ime command Syntax mac address table aging time aging time no mac address table aging time Parameter aging time The aging time for the dynamic address The value of it can be 0 or ranges from 10 to 630 seconds When 0 is entered the Auto Aging function is disabled It is 300 by default Command Mode Global Configuration Mode Example Configure the aging time as 500 seconds TL SL5428E config mac address table aging time 500 mac address table filtering Description The mac address table filtering command is used to add the filtering address entry To delete the corresponding entry please use no mac address table filtering command The filtering address function is to forbid the undesired package to be forwarded The filtering address can be added or removed manually independent of the aging time Syntax mac address table filtering mac adadr vid vid no mac address table filtering mac addr vid vid Parameter mac addr The MAC address to be filtered 113 TL SL5428E ENI LLE A EEN EG e BRETT vid The corresponding VLAN ID of the MAC address It ranges from 1 to 4094 Command Mode Global Configuration Mode Example Add a filtering address entry of which VLAN ID is 1 and MAC address is 00 1e 4b 04 01 5d TL SL5428E config mac address table filtering 00 1e 4b 04 01 5d vid 1 mac address table max mac count Description The mac address table max mac count command is used to configure the
134. ine login local Configure the login of Console port connection 0 as login local mode TL SL5428E config line console 0 TL SL5428E config line login local 64 TL SL5428E BAG 6 0 5 1 a EME Eli e BRETT show user account list Description The show user account list command is used to display the information of the current users Syntax show user account list Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of the current users TL SL5428E config show user account list show user configuration Description The user configuration command is used to display the security configuration information of the users including access control max number and the idle timeout etc Syntax show user configuration Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the security configuration information of the users TL SL5428E config show user configuration 65 TL SL5428E BAG 6 0 5 1 aE TATT DL EG e M EE ETT IT Chapter 12 Binding Table Commands You can bind the IP address MAC address VLAN and the connected Port number of the Host together which can be the condition for the ARP Inspection and IP verify source to filter the packets ip source binding Description The ip source binding command is used to bind the IP address MAC address VLAN ID and the Port number together manually You can manually bind the IP address MAC address
135. ion Mode 253 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Example Display the member information TL SL5428E show cluster member show cluster manage role Description The show cluster manage role command is used to display the role of the current switch Syntax show cluster manage role Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the role of the current switch TL SL5428E config show cluster manage role show cluster time segment Description The show cluster time segment command is used to display the information of the time segment entry Syntax show cluster time segment Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of the time segment entry TL SL5428E config show cluster time segment 254 TL SL5428E BA 6 0 5 1 aE Tare Te DL Eli e BRETT show cluster manage batch management Description The show cluster manage batch management command is used to display the batch management status of the switches in cluster Syntax show cluster manage batch management Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the status of the switches in cluster TL SL5428E config show cluster manage batch management 255
136. ion option Command Mode Global Configuration Mode Example Enable the Option 82 function of DHCP Snooping TL SL5428E config ip dhcp snooping information option ip dhcp snooping information strategy Description The ip dhcp snooping information strategy command is used to select the operation for the Option 82 field of the DHCP request packets from the Host To restore to the default option please use no ip dhcp snooping information strategy command Syntax ip dhcp snooping information strategy strategy no ip dhcp snooping information strategy Parameter strategy The operations for Option 82 field of the DHCP request packets from the Host including three types keep Indicates to keep the Option 82 field of the packets It is the default option replace Indicates to replace the Option 82 field of the packets with the switch defined one drop Indicates to discard the packets including the Option 82 field Command Mode Global Configuration Mode Example Replace the Option 82 field of the packets with the switch defined one and then send out TL SL5428E config ip dhcp snooping information strategy replace 70 TL SL5428E BAS KY LLE a EEN Eli e BRETT ip dhcp snooping information remote id Description The ip dhcp snooping information remote id command is used to enable and configure the customized sub option Remote ID for the Option 82 To return to default Remote ID for the Option 82 please use no ip dhc
137. is 2 seconds reinit delay This parameter indicates the amount of delay from when LLDP status becomes disable until re initialization will be attempted The value ranges from 1 to 10 and the default value is 3 notify interval Specify the interval of Trap message which will be sent from local device to network management system The value ranges from 5 to 3600 and the default value is 5 seconds fast count When the port s LLDP state transforms from Disable or Rx_Only to Tx amp Rx or Tx_Only the fast start mechanism will be enabled that 234 TL SL5428E BA 6 KT LLE a EME Eli e M EE ETT IT is the transmit interval will be shorten to a second and several LLDPDUs will be sent out the number of LLDPDUs equals this parameter The value ranges from 1 to 10 and the default value is 3 Command Mode Global Configuration Mode Example Specify the Transmit Interval of LLDPDU as 45 seconds and Trap message to NMS as 120 seconds TL SL5428E config lldp timer tx interval 45 TL SL5428E config Hlldp timer notify interval 120 Ildp receive Description The Ildp receive command is used to enable the designated port to receive LLDPDU To disable the function please use no Ildp receive command Syntax lldp receive no Ildp receive Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Examp
138. ision level for MST region identification ranging from 0 to 65535 Command Mode MST Configuration Mode Example Configure the revision level of MST as 100 TL SL5428E config spanning tree mst configuration TL SL5428E config mst revision 100 spanning tree mst instance Description The spanning tree mst instance command is used to configure the priority of MST instance To return to the default value of MST instance priority please use no spanning tree mst instance command Syntax spanning tree mst instance instance id priority pri no spanning tree mst instance instance id priority Parameter instance id Instance ID ranging from 1 to 8 pri MSTI Priority which must be multiple of 4096 ranging from 0 to 61440 By default it is 32768 MSTI priority is an important criterion on determining if the switch will be chosen as the root bridge in the specific instance Command Mode Global Configuration Mode Example Enable the MST Instance 1 and configure its priority as 4096 TL SL5428E config spanning tree mst instance 1 priority 4096 187 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT spanning tree mst Description The spanning tree mst command is used to configure MST Instance Port To return to the default configuration of the corresponding Instance Port please use no spanning tree mst command A port can play different roles in different spamning tree instance You can use this command to configure
139. ist Parameter vlan list VLAN ID list ranging from 2 to 4094 in the format of 2 3 5 It is multi optional Command Mode Global Configuration Mode Example Create VLAN 2 10 and VLAN 100 TL SL5428E config vlan 2 10 100 Delete VLAN 2 TL SL5428E config no vian 2 19 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT interface vian Description The interface vlan command is used to create VLAN Interface hereafter to access to Interface VLAN Mode Syntax interface vlan vian id no interface vlan vian id Parameter vlan id Specify IEEE 802 1Q VLAN ID ranging from 1 to 4094 Command Mode Global Configuration Mode Example Create VLAN Interface 2 TL SL5428E config interface vlan 2 name Description The name command is used to assign a description string to a VLAN To clear the description please use no name command Syntax name descript no name Parameter descript String to describe the VLAN which contains 16 characters at most Command Mode VLAN Configuration Mode VLAN 20 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Example Specify the description string of the VLAN 2 as VLANOO02 TL SL5428E config vlan 2 TL SL5428E config vian name VLANO02 switchport mode Description The switchport mode command is used to configure the Link Types for the ports Syntax switchport mode access trunk general Parameter access trunk general
140. itEthernet 1 0 25 TL SL5428E config if loopback detection recover show loopback detection global Description The show loopback detection global command is used to display the global configuration of loopback detection function such as loopback detection global status loopback detection interval and loopback detection recovery time Syntax show loopback detection global Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of loopback detection function TL SL5428E show loopback detection global 164 TL SL5428E MOSUCEU MIA EME DL Eli e M EE ETT IT show loopback detection interface Description The show loopback detection interface command is used to display the configuration of loopback detection function and the status of all ports or of a specified Fast Gigabit Ethernet port Syntax show loopback detection interface fastEthernet port gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of loopback detection function and the status of Fast Ethernet port 5 TL SL5428E show loopback detection interface fastEthernet 1 0 5 Display the configuration of loopback detection function and the status of all ports TL SL5428E show loopback detection interface 165 TL SL5428E BAG 6 0 5 1 aE TATT DL EG e M EE ETT IT Chapter 2
141. itEthernet 1 0 25 mode show spanning tree interface security Description The show spanning tree interface security command is used to display the protect information of all ports or a specified port Syntax show spanning tree interface security fastEthernet port gigabitEthernet port bpdufilter bpduguard loop root tc tc defend 196 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the protect information of all ports TL SL5428E config show spanning tree interface security Display the protect information of Gigabit Ethernet port 25 TL SL5428E config show spanning tree interface security gigabitEthernet 1 0 25 Display the interface security bpdufilter information TL SL5428E config show spanning tree interface security bpdufilter show spanning tree mst Description The show spanning tree mst command is used to display the related information of MST Instance Syntax show spanning tree mst configuration digest instance instance id interface fastEthernet port gigabitEthernet port Parameter instance id Instance ID desired to show ranging from 1 to 8 port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the region infor
142. kets received Syntax clear ip arp inspection statistics Command Mode Privileged EXEC Mode and Any Configuration Mode Example Clear the statistic of the illegal ARP packets received TL SL5428E config clear ip arp inspection statistics 81 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Chapter 14 IP Verify Source Commands IP Verify Source is to filter the IP packets based on the IP MAC Binding entries Only the packets matched to the IP MAC Binding rules can be processed which can enhance the bandwidth utility ip verify source Description The ip verify source command is used to configure the IP Verify Source mode for a specified port To disable the IP Verify Source function please use no ip verify source command Syntax ip verify source sip sip mac no ip verify source Parameter sip sip mac Security type sip indicates that only the packets with its source IP address and port number matched to the IP MAC binding rules can be processed sip mac indicates that only the packets with its source IP address source MAC address and port number matched to the IP MAC binding rules can be processed Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEhternet Example Enable the IP Verify Source function for Fast Ethernet ports 5 10 Configure that only the packets with its source IP a
143. kets with authentication data can be encapsulated in the advanced protocol such as RADIUS packets to be transmitted to the authentication server Command Mode Global Configuration Mode Example Configure the Authentication Method of IEEE 802 1X as pap TL SL5428E config dot1x auth method pap dot1x guest vlan global Description The dot1x guest vlan command is used to enable the Guest VLAN function globally To disable the Guest VLAN function please use no dot1x guest vlan command Syntax dot1x guest vlan vid no dot1x guest vlan Parameter vid The VLAN ID needed to enable the Guest VLAN function ranging from 2 to 4094 The supplicants in the Guest VLAN can access the specified network source Command Mode Global Configuration Mode Example Enable the Guest VLAN function for VLAN 5 90 TL SLSA7pERIGCEIORRKR EIET DL Eli e BRETT TL SL5428E config dot1x guest vlan 5 dot1x quiet period Description The dot1x quiet period command is used to enable the quiet period function To disable the function please use no dot1x quiet period command Syntax dot1x quiet period no dot1x quiet period Command Mode Global Configuration Mode Example Enable the quiet period function TL SL5428E config dot1x quiet period dot1x timeout Description The dot1x timeout command is used to configure the quiet period and the supplicant timeout To restore to the default please use no dot1x tim
144. le Enable Fast Ethernet port 1 to receive LLDPDU TL SL5428E config interface fastEthernet 1 0 1 TL SL5428E config if lldp receive Ildp transmit Description The Ildp transmit command is used to enable the designated port to transmit LLDPDU To disable the function please use no Ildp transmit command 235 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Syntax lldp transmit no Ildp transmit Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable Fast Ethernet port 1 to transmit LLDPDU TL SL5428E config interface fastEthernet 1 0 1 TL SL5428E config if lldp transmit Ildp snmp trap Description The Ildp snmp trap command is used to enable the ports SNMP notification If enabled the port will notify the trap event to network management system To disable the ports SNMP notification please use no Ildp snmp trap command Syntax lldp snmp trap no lldp snmp trap Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the SNMP notification for Fast Ethernet port 1 TL SL5428E config interface fastEthernet 1 0 1 TL SL5428E config if lldp snmp trap 236 TL SL5428E MOSCA EEN Eli e BRETT Ildp tlv select Description The Ildp
145. lete the VLAN Mapping entry please use the no dot1q tunnel mapping command Syntax dot1q tunnel mapping c v an sp vlan descripf no dot1q tunnel mapping c vian Parameter c vlan Customer VLAN ID ranging from 1 to 4094 sp vlan Service Provider VLAN ID ranging from 1 to 4094 descript Give a description to the VLAN Mapping entry which contains 15 characters at most Command Mode Global Configuration Mode Example Add a VLAN Mapping entry named TP with the C VLAN being 2 and the SP VLAN being 10 TL SL5428E config dot1q tunnel mapping 2 10 TP 34 TL SL5428E MOSCA EME EG e M EE ETT IT switchport dot1q tunnel mapping Description The switchport dot1q tunnel mapping command is used to enable the VLAN Mapping feature for a specified port To disable the VLAN Mapping feature of this port please use the no switchport dot1q tunnel mapping command By default the VLAN Mapping feature of all ports is disabled Syntax switchport dot1q tunnel mapping no switchport dot1q tunnel mapping Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the VLAN Mapping feature for the Fast Ethernet port 3 TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if switchport dot1q tunnel mapping switchport dot1q tunnel mode uplink Description The swi
146. llowed vlan v an list all Parameter vlan list VLAN ID list ranging from 2 to 4094 in the format of 2 3 5 It is multi optional all Add the port to all of the existing VLANs Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure the link type of port 2 as trunk and add it to VLAN 2 TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if switchport mode trunk 22 TL SL5428E MOSCA EEN EG e BRETT TL SL5428E config if switchport trunk allowed vlan 2 switchport general allowed vlan Description The switchport general allowed vlan command is used to add the desired General port to IEEE 802 1Q VLAN or to remove a port from the corresponding VLAN Syntax switchport general allowed vlan vian list tagged untagged no switchport general allowed vlan vian list Parameter vlan list VLAN ID list ranging from 2 to 4094 in the format of 2 3 5 It is multi optional tagged untagged egress rule Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure Fast Ethernet port 4 whose link type is general to VLAN 2 and its egress rule as tagged TL SL5428E config interface fastEthernet 1 0 4 TL SL5428E config if switchport mod
147. logging host INDEX eee e cece eeeeeeeeeeeeeeeeneeeeeeeeeeeeeeeseeeceeeceeeneeeseeaeeeaeeeaeeeaeeeaeesaeeeaeenaas 101 show logging local COnfig cccceceeeeeeceeeeceeeceeeeeeeceeeceeeeeeeeececeaeaeeeeeeeeseeeeieaeeeeeeeeteeeeeas 102 Show logging ee le EE 102 Showlogging BEE 103 SHOW logging flash ET 103 Chapter 18 SSH CoMManNdS oooonnnnnncccccccconononcnnnnncnononennnanannnnnnncnenennnnnannnnnnernnnnnnnas 105 PSSS EE 105 IP SSIVORSION adn alas 105 IA ON RN 106 IPsSSM E e E cdi 106 IE A SS 107 Ne Ve E D 107 Chapter 19 SSL CommandS nasa A a as 109 IP MUP SECUPE SEIV A Ee ee EEN Ee Een 109 VI ip http secure server download Certificate ooooonnninococinnnnnncccnnnccnconononnnnnnnnnonononcnnnnnnnss 109 ip http secure server download key 110 show ip http secure senver cocococccccccononononnnnn nono non nn nn 111 Chapter 20 MAC Address COMMANdOS cooonnnnnnncccconecononannnnnncnnnnnnnnnananannnnnnnnnnnnnnanos 112 mac address table stat AANER 112 mac address table aging time AAA 113 mac address table filtering 2 0 0 2 cccceceeeccececeeeeeeeceneaeeeeeeeeeeeceneaaeeeeeeeeseseeeaeeeeeeeeeesesneueaneees 113 mac address table max Mac cCount eenen nenene enneren eneen nnn enne nnne nnne nnne neee nennt 114 show mac address table NEE 115 show mac address table aging tIMe oooooconconocccncooonnnncnnncnnncnoncnnnnnnnnnnnnnnn nono nnnnnnnnnnnnnnnnnnnns 116 show mac address table max mac count inte
148. loop Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the Loop Protect function for Fast Ethernet port 2 TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if spanning tree guard loop spanning tree guard root Description The spanning tree guard root command is used to enable the Root Protect function for a port With the Root Protect function enabled the root bridge will set itself automatically as ERROR PORT when receiving BPDU packets with higher priority in order to maintain the role of root bridge To disable the Root Protect function please use no spanning tree guard root command Syntax spanning tree guard root no spanning tree guard root 193 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the Root Protect function for Fast Ethernet port 2 TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if spanning tree guard root spanning tree guard tc Description The spanning tree guard tc command is used to enable the TC Protect of Spanning Tree function for a port To disable the TC Protect of Spanning Tree function please use no spanning tree guard tc command A switch removes MA
149. lue The maximum number of BPDU packets transmitted per Hello Time interval ranging from 1 to 20 in pps By default it is 5 Command Mode Global Configuration Mode Example Configure the hold count of STP as 8pps TL SL5428E config spanning tree hold count 8 spanning tree max hops Description The spanning tree max hops command is used to configure the maximum number of hops that occur in a specific region before the BPDU is discarded To return to the default configurations please use no spanning tree max hops command Syntax spanning tree max hops value no spanning tree max hops Parameter value The maximum number of hops that occur in a specific region before the BPDU is discarded ranging from 1 to 40 in hop By default it is 20 Command Mode Global Configuration Mode Example Configure the max hops of STP as 30 TL SL5428E config spanning tree max hops 30 191 TL SL5428E BA 6 0 5 1 MIA EME EG e BRETT spanning tree bpdufilter Description The spanning tree bpdufilter command is used to enable the BPDU filter function for a port With the function enabled the port can be prevented from receiving and sending any BPDU packets To disable the BPDU filter function please use no spanning tree bpdufilter command Syntax spanning tree bpdufilter no spanning tree bpdufilter Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gig
150. lues can be typed for a port list or a vlan list using comma to separate Use a hyphen to designate a range of values for instance 1 3 5 7 indicates choosing 1 3 4 5 and 7 The port number must enter in the format of 1 0 3 meaning unit slot port The unit number is always 1 and slot number is always O and the port number is a variable an actual value must be assigned 14 TL SL5428E BAG 6 0 5 1 a EME Eli e BRETT Chapter 2 User Interface enable Description The enable command is used to access Privileged EXEC Mode from User EXEC Mode Syntax enable Command Mode User EXEC Mode Example If you have set the password to access Privileged EXEC Mode from User EXEC Mode TL SL5428E gt enable Enter password TL SL5428E enable password Description The enable password command is used to set the password for users to access Privileged EXEC Mode from User EXEC Mode To return to the default configuration please use no enable password command Syntax enable password password secret simple cipher no enable password Parameter password super password which contains 31 characters at most composing digits English letters and underdashes only By default it is empty simple cipher The way of displaying password in configuration file By default it is simple Command Mode Global Configuration Mode Example Set the super password as admin to access Privileged EXEC Mode from User EX
151. lun Le ati a cis 166 ASUME IS AAA A A A A A A AI 166 lee e 167 Welte ET 168 Weller te e e IR EE 168 ACCESSHIISU e 169 ue EE 169 lee ele ee ME 170 ACCESS ASCO EE 171 Ml door Melee eat te art a 172 access list policy name 174 ACCESS IISE policy Ted e voor a e 174 red lechera a e e A 175 redirect O et dteesnt ee eieedaat s 175 COMMON Ai ii 176 SIMIO E and dedos 177 JOSE Ma A AAA A DEE AER 177 access list bind interface ivi aL bos 178 ACCESS ISHDIMACVIAN DEE 178 SNOW TIME TANGE ii A ee ee a 179 Delen EE 179 SHOW ACCESS S E 180 Ge UE dee e 180 SNOW ACCeSS lISt DING it ai ahaa Mee id ts eae eats 180 Chapter 28 MSTP Commands oooonnnncccccccccnnnnnncnnncnononcnnnnnnanannnnnonenennnnnannnnnnnnnnnnnnnas 182 Spanning Dreeidlobal nace Eneee erene 182 spanning tree interface ooocoocccccccccnnccccncononncnnnnnncoconnnnronnnnnnnonnnnnnnnnncnnnnnnnanannnnnnncnncncininnnns 182 spanning tree COMMONK CONAIY occcccccccnnccnnnnonnnonnnonnnonononononononononnnnnonnnnnnnnnononnnnnnnnnnnnnnnnnnoss 183 SPANMING tES EE 184 spanning tree mst configuration oooooocooncconnnnnnnoncnonnnnnnnnnnnnnnnnnnnnnnnnononnnnnnnnnnnnnnnnnnnnnononnss 185 A seca ceca the cette esate S tad state Ata cap teat bmn eet A deen eta 185 W 186 FOVISIOM EE 186 spanning tree mei INSTANCE necer rura a AEE a C aaa e Eea REE TaN AEAEE aane 187 SPANNING trES E 188 SPANNING tree elle EE 188 Spanning tree tG detend ttrt ttr rttArttArEEAEEEAAEEAAEEEEEEA
152. mation and mapping information of VLAN and MST Instance TL SL5428E config show spanning tree mst configuration Display the related information of MST Instance 1 TL SL5428E config show spanning tree mst instance 1 197 TL SL5428E BAG 6 KY T is a Taree D EC Oe REI Display all the ports information of MST Instance 1 TL SL5428E config show spanning tree mst instance 1 interface 198 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Chapter 29 IGMP Commands IGMP Snooping Internet Group Management Protocol Snooping is a multicast control mechanism running on Layer 2 switch It can effectively prevent multicast groups being broadcasted in the network ip igmp snooping global Description The ip igmp snooping command is used to configure IGMP Snooping globally To disable the IGMP Snooping function please use no ip igmp snooping command Syntax ip igmp snooping no ip igmp snooping Command Mode Global Configuration Mode Example Enable IGMP Snooping function TL SL5428E config ip igmp snooping ip igmp snooping interface Description The ip igmp snooping command is used to enable the IGMP Snooping function for the desired port To disable the IGMP Snooping function please use no ip igmp snooping command Syntax ip igmp snooping no ip igmp snooping Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabi
153. me The name of the policy desired to bind 178 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Command Mode Interface VLAN Mode Example Bind policy1 to VLAN 2 TL SL5428E config interface vlan 2 TL SL5428E config if access list bind policy1 show time range Description The show time range command is used to display the configuration of time range Syntax show time range Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of Time Range TL SL5428E show time range show holiday Description The show holiday command is used to display the defined holidays Syntax show holiday Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the defined holidays TL SL5428E show holiday 179 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT show access list Description The show access list command is used to display configuration of ACL Syntax show access list acl id Parameter acl id The ID of the ACL selected to display the configuration Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of the MAC ACL whose ID is 20 TL SL5428E show access list 20 show access list policy Description The show access list policy command is used to display the information of a specified policy Syntax show access list policy name Parameter name The Policy Name desired to show C
154. me US Canada UTC 06 00 TimeZone for Central Time US Canada UTC 05 00 TimeZone for Eastern Time US Canada UTC 04 30 TimeZone for Caracas UTC 04 00 TimeZone for Atlantic Time Canada UTC 03 30 TimeZone for Newfoundland UTC 03 00 TimeZone for Buenos Aires Salvador Brasilia UTC 02 00 TimeZone for Mid Atlantic UTC 01 00 TimeZone for Azores Cape Verde Is UTC TimeZone for Dublin Edinburgh Lisbon London UTC 01 00 TimeZone for Amsterdam Berlin Bern Rome Stockholm Vienna UTC 02 00 TimeZone for Cairo Athens Bucharest Amman Beirut Jerusalem UTC 03 00 TimeZone for Kuwait Riyadh Baghdad UTC 03 30 TimeZone for Tehran UTC 04 00 TimeZone for Moscow St Petersburg Volgograd Tbilisi Port Louis UTC 04 30 TimeZone for Kabul UTC 05 00 TimeZone for Islamabad Karachi Tashkent UTC 05 30 TimeZone for Chennai Kolkata Mumbai New Delhi UTC 05 45 TimeZone for Kathmandu UTC 06 00 TimeZone for Dhaka Astana Ekaterinburg UTC 06 30 TimeZone for Yangon Rangoon UTC 07 00 TimeZone for Novosibrisk Bangkok Hanoi Jakarta UTC 08 00 TimeZone for Beijing Chongqing Hong Kong Urumai Singapore UTC 09 00 TimeZone for Seoul Irkutsk Osaka Sapporo Tokyo UTC 09 30 TimeZone for Darwin Adelaide UTC 10 00 TimeZone for Canberra Melbourne S
155. mit The operation to forward packets It is the default value source ip The source IP address contained in the rule source ip mask The source IP address mask It is required if you typed the source IP address destination ip The destination IP address contained in the rule destination ip mask The destination IP address mask It is required if you typed the destination IP address time segment The time range for the rule to take effect By default it is not limited 170 TL SL5428E BA 6 0 5 1 a EME Eli e BRETT frag Enable Disable Fragment By default it is disabled If Fragment is enabled this rule will process all the fragments and the last piece of fragment will be always forwarded Command Mode Global Configuration Mode Example Create a Standard IP ACL whose ID is 120 and add Rule 10 for it In the rule the source IP address is 192 168 0 100 the source IP address mask is 255 255 255 0 the time range for the rule to take effect is tSeg1 and the packets match this rule will be forwarded by the switch TL SL5428E config access list create 120 TL SL5428E config access list standard 120 rule 10 permit sip 192 168 0 100 smask 255 255 255 0 tseg tSeg1 access list extended Description The access list extended command is used to add Extended IP ACL rule To delete the corresponding rule please use no access list extended command Syntax access list exten
156. mmand Mode Global Configuration Mode Example Bind an ACL entry with the IP 192 168 0 1 MAC 00 00 00 00 00 01 VLAN ID 2 and the Port number 5 manually And then enable the entry for the ARP detection and IP filter function TL SL5428E config ip source binding host1 192 168 0 1 00 00 00 00 00 01 vian 2 interface fastEthernet 1 0 5 both Delete the IP MAC VID PORT entry with the index 5 TL SL5428E config no ip source binding index 5 ip source binding index Description The ip source binding index command is used to modify the existing entry of ip source binding Syntax ip source binding index idx hostname hostname mac mac addr vlan vian id interface fastEthernet port gigabitEthernet porf none arp detection ip verify source both Parameter idx The entry number needed to be modified You can use the show ip source binding command to get the idx Pay attention that the entry number is the actual number in the binding table which is not displayed in an arranged order hostname The modified Host Name which contains 20 characters at most mac addr The modified MAC address of the Host vlan id The modified VLAN ID ranging from 1 to 4094 port The modified number of port connected to the Host none arp detection ip verify source both The modified protect type for the entry arp detection indicates ARP detection ip verify source indicates IP
157. mode v3 slev authNoPriv read viewDefault write viewDefault notify viewDefault Delete Group group 1 TL SL5428E config no snmp server group group1 smode v3 slev authNoPriv snmp server user Description The snmp server user command is used to add User To delete the corresponding User please use no snmp server user command The User in an SNMP Group can manage the switch via the management station software The User and its Group have the same security level and access right 216 TL SL5428E BAG 6 0 5 1 KREIEN le BRETT Syntax snmp server user name local remote group name smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv H emode none MD5 SHA cpwd confirm pwa emode none DES epwd encrypt pwa no snmp server user name Parameter name User Name ranging from 1 to 16 characters local remote User Type with local and remote options Local indicates that the user is connected to a local SNMP engine while remote indicates that the user is connected to a remote SNMP engine group name The Group Name of the User The User is classified to the corresponding Group according to its Group Name Security Model and Security Level smode The Security Model of the User with v1 v2c and v3 options By default the option is v1 The Security Model of the User must be the same with that of the Group which the User belongs to slev The Security L
158. n March 01 00 Last Sunday in October 01 00 New Zealand Last Sunday in September 02 00 First Sunday in April 03 00 Command Mode Global Configuration Mode Example Configure the DST period of the switch as European TL SL5428E config system time dst predefined European 121 TL SL5428E BA 6 0 5 1 MIA EME EG e M EE ETT IT system time dst date Description The system time dst date command is used to specify the DST configuration in Date mode This configuration is one off in use By default the current year is used as the starting time DST time periods should be within 12 months over one two year Syntax system time dst date smonth sday stime emonth eday etime offset Parameter smonth Month to start with the options Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec sday Day to start ranging from 1 to 31 Please mind that the number of days depends on the month stime Time to start in the format of hh mm emonth Month to end with the options Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec eday Day to end ranging from 1 to 31 Please mind that the number of days depends on the month etime Time to end in the format of hh mm offset Specify the time adding in minutes when Daylight Saving Time comes The value ranges from 1 to 1440 and the default value is 60 minutes It is optional Command Mode Global Configurati
159. nabled coldstart Enable coldstart trap It is sent upon switch reboot By default it is enabled Command Mode Global Configuration Mode Example Enable SNMP standard linkup trap for the switch TL SL5428E config snmp server traps snmp linkup 221 TL SL5428E MOSUCEIU MIA EME EG e BRETT snmp server traps link status Description The snmp server traps link status command is used to enable SNMP link status trap for the specified port To disable the sending of SNMP link status trap please use no snmp server traps link status command Syntax snmp server traps link status no snmp server traps link status Command Mode Interface Configuration Mode interface gigabitEthernet interface range gigabitEthernet Example Enable SNMP link status trap for port 3 TL SL5428E config interface gigabitEthernet 1 0 3 TL SG3424P config if snmp server traps link status snmp server traps Description The snmp server traps command is used to enable SNMP extended traps To disable the sending of SNMP extended traps please use no snmp server traps command Syntax snmp server traps bandwidth control cpu flash ipaddr change Ildp loopback detection storm control spanning tree memory no snmp server traps bandwidth control cpu flash ipaddr change Ildp loopback detection storm control spanning tree memory Parameter bandwidth control Enable bandwidth control tra
160. nd neighboring connection information of each device in a specific network range It provides the commander switch with the information of devices which can join the cluster and collects topology information of devices within the specified hops cluster ntdp cluster ntdp timer interval time time hop delay va ue port delay value cluster ntdp hop hop value no cluster ntdp no cluster ntdp timer interval time time hop delay value port delay value no cluster ntdp hop hop value Parameter time NTDP Interval Time which is the interval to collect topology information NTDP Interval Time ranges from 1 to 60 in minutes By default it is 1 hop delay value NTDP Hop Delay which is the time between the switch receiving NTDP request packets and the switch forwarding NTDP request packets for the first time NTDP Hop Delay ranges from 1 to 1000 in milliseconds By default it is 200 port delay value NTDP Port Delay which is the time between the port forwarding NTDP request packets and its adjacent port forwarding NTDP request packets over NTDP Port Delay ranges from 1 to 100 in milliseconds By default it is 20 hop value NTDP Hops which is the hop count the switch topology collects NTDP Hops ranges from 1 to 16 By default it is 3 Command Mode Global Configuration Mode 242 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Example Enable NTDP function globally and spe
161. net port gigabitEthernet port basic config filter packet stat show ip igmp snooping interface fastEthernet port list gigabitEthernet port list basic config filter packet stat Parameter port The Fast Gigabit Ethernet port number By default the configuration of all ports is displayed basic config filter packet stat The related configuration information selected to display port list The list group of Ethernet ports Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the IGMP basic configuration of Fast Ethernet port 2 TL SL5428E show ip igmp snooping interface fastEthernet 1 0 2 basic config 209 TL SL5428E BAG 6 0 5 1 a EME EG e M EE ETT IT Display the IGMP filter configuration of Fast Ethernet ports 2 4 TL SL5428E show ip igmp snooping interface fastEthernet 1 0 2 4 filter show ip igmp snooping vian Description The show ip igmp snooping vlan command is used to display the VLAN configuration of IGMP Syntax show ip igmp snooping vlan v an id Parameter vlan id The VLAN ID selected to display Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the IGMP snooping configuration information of VLAN 2 TL SL5428E show ip igmp snooping vlan 2 show ip igmp snooping multi vlan Description The show ip igmp snooping multi vlan command is used to display the Multicast VLAN configuration Syntax s
162. nfiguration Mode Example Cancel the auto backup operation of the switch with index 1 TL SL5428E config cluster manage batch management cancel index 1 show cluster ntdp Description The show cluster ntdp command is used to display NTDP configuration information Syntax show cluster ntdp interface fastEthernet port gigabitEthernet port device list Parameter port The Fast Gigabit Ethernet port number By default the configuration of all Fast Gigabit Ethernet ports is displayed device list To display the device table of NTDP 252 TL SL5428E BA 6 KT LL a VET Xe DL EG e m EE ETT IT Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global information of NTDP TL SL5428E show cluster ntdp Display the NTDP configuration of all Ethernet ports TL SL5428E show cluster ntdp interface Display the device table of NTDP TL SL5428E show cluster ntdp device list show cluster Description When the current switch is Commander Switch the show cluster command is used to display the global configuration of Cluster Syntax show cluster Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of Cluster TL SL5428E show cluster show cluster member Description The show cluster member command is used to display the member information Syntax show cluster member Command Mode Privileged EXEC Mode and Any Configurat
163. ng a2 2 0 44 Wiss it A A See Ee Stee 34 switchport dot1q tunnel Mapping cccccccccccccconccnncnnncnnncnnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnonnnnnncnnss 35 switchport dot1q tunnel mode uplink ooooooocccncccncccncccnncnnncnnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnonononcninonons 35 le ee ae ET Olivia A ia A tas 36 show dot1q tunnel Mapping nnn cnn 36 show dot1q tunnel mapping Interface 37 show dot1q tunnel uplmk 00 ceeeceeeeeeeeeee eee aeeeaeee eee eaeeaaee sees aaeeaaeeaaee sae eaaeaaaeaaeeaaaeeaaeeaaeaaes 37 Chapter 7 Voice VLAN Commands cccooonnnnnnncncccnencnnnanannnncnncnnnnnnnnnnnnnnnnnnnnnnnnnanans 38 VOICE VIM EE 38 VOICE VIAN AGING ul 38 VOICE Vlani PROLLY scsi eared A AA Zeen de Side geed Eege 39 Voice vlan MaC addIess EE 40 switchport Voice Vlan mode kk 40 switchport voice vlan Security 41 SNOW VOICE WEE 42 Show Vice VAN OU eee 42 Show voice vlan switchport nono nnncnnncnnncnnnnnnncnnncnnnonnnonnnonnss 43 Chapter 8 Private VLAN Commande ccooonnnnnnncccccncnononanannnnnnnnnnnnnnnnnnnnnnnnnnnnennnannns 44 Private VIAN primary ococcccccnccnncnonononononononononononnnnnnn aaeeaaee sees cues nono sees sees sees nnnonnnennnonnnennnonncnnninnnss 44 private vlan Communffy EEEE E AEAEE EEEE EEEE E EEEE E EEEn n nnen nennen nnan 44 private vlan association 45 SWitehport piate a WEE 45 switchport private vlan host associati0N ooooooconnconocoooconoconnconnnonnconoconononoconononononononononnc
164. ng filter 3 225 1 1 1 226 3 2 1 ip igmp snooping filter interface Description The ip igmp snooping filter command is used to configure Port Filter To return to the default configuration please use no igmp snooping filter command When the switch receives IGMP report message it examines the multicast filtering IP ID configured on the access port to determine if the port can join the multicast group If the multicast IP is not filtered the switch will add the port to the forward port list of the multicast group Otherwise the switch will drop the IGMP report message In that way you can control the multicast groups that users can access Syntax ip igmp snooping filter no ip igmp snooping filter 204 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable IGMP Snooping filter function for Gigabit Ethernet port 26 TL SL5428E config interface gigabitEthernet 1 0 26 TL SL5428E config if ip igmp snooping filter ip igmp snooping filter maxgroup Description The ip igmp snooping filter maxgroup command is used to specify the maximum number of multicast groups for a port to join in Syntax ip igmp snooping filter maxgroup maxgroup Parameter maxgroup The maximum number of multicast groups for a port to join in It is used to prevent some po
165. nge the ports can join so as to restrict users ordering multicast programs via configuring multicast filter rules Multicast IP addresses ranges from 224 0 0 0 to 239 255 255 255 The range for receivers to join is from 224 0 1 0 to 239 255 255 255 Syntax ip igmp snooping filter addr id adar id list no ip igmp snooping filter addr id addr id list Parameter addr id list The filtering address ID to be bound Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Bind the filtering address ID 2 6 to Fast Ethernet port 3 TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if ip igmp snooping filter addr id 2 6 203 TL SL5428E BAG 6 0 5 1 Wa VE Tare Xe DL Eli e m EE ETT IT ip igmp snooping filter global Description The ip igmp snooping filter command is used to add or modify the multicast filtering IP range To delete the multicast filtering IP range please use no ip igmp snooping filter command Syntax ip igmp snooping filter id start ip end ip no ip igmp snooping filter id Parameter id P range ID ranging from 1 to 30 start ip The start multicast IP of the IP range end ip The end multicast IP of the IP range Command Mode Global Configuration Mode Example Modify the multicast IP range whose ID is 3 as 225 1 1 1 226 3 2 1 TL SL5428E config ip igmp snoopi
166. nnncnnns 46 switchport private vlan Mapping eee aeee eens aces aces aeeeaeeeaee sues sees sues aaeeaaeeaaeeaaeeaaeeaes 47 show Vlan private VAN octanos 48 Chapter 9 GVRP COMMANdS cooonnncccccccccnnnncnnnncncncncnnnnnanannnnnnnnnnnnnnnannnnnrrrnnnennnnaannns 49 gi OO 49 QVrpi inteMmace EE 49 gvrp reGistration EEN 50 eigene 51 Show gyrp MODA ici AAA a ee A E A A 52 SNOW QVip Tue 52 Chapter 10 Etherchannel COMMANAS cooooonnnnnncccccncccnnonanannnnnennnnnnnannnnnnnnnnnnnennnanans 53 ER Ile ele 1 EE 53 port channel oad balance AAA 54 lacp System priority iii eee ie ee ie el A ee eet 54 ACP pOrEprO ler 55 shoW etherchannel lccccciosast nella aa a eaaa 55 show etherchannel load balance nnne 56 aoa e o E EE E A E A E A E 56 Deler SyS i EE 57 Chapter 11 User Manage Commandes ken 58 USC LEET 58 user access control phase 59 user access control machbhased 59 user access control port based AAA 60 USE MAX NUMDESR lucia a li rad ra E aden Ines 61 USERS Te LEE 61 Eenheete ER ee ENE 62 DASSWOMD WEE 63 ele IL EE 63 LOGIN Be e EE 64 le Ve e ee ln EE 65 SHOW USer Gong Sen edeteteae tratas cen Red Ee E Eege enge geen 65 Chapter 12 Binding Table Command6 e iti titi iin niin 66 IP SOULCE DINING EE 66 IP SOUFCE DINGING IND EE 67 Eelere Bue ne WEE 68 ip dhcp Snooping golobal nnt 68 ip dhcp snooping information option 69 ip dhcp snooping information strategy cccconocnccocccnncocicncanonnnnnononnoncnnnnnn
167. nnnnnnnoncnnnnnnnnononinnns 70 ip dhcp snooping information remote jd rner trretern nnen eere ne 71 ip dhcp snooping information circuit id ooooconnnccococccnnconocanonocnnnncnnoncnnrnnnonnnnnnoncnnnnnnnnnnnoninnns 71 IPZANCP SMOOPING TUS EEN 72 ip dhcp snooping mac verify ccocccccncncocococccccccncononnnnnnnnononcnnnnnnnnnnnnnnnnnnnnnnnnnnnnnneninnnnnnnnnnnnnenens 73 ip dhcp snooping limit r Le E E E nero ncnnnenonenineniness 73 ip dhcp shooping declines e i eaa ie i aen i testes 74 SNOW IP Source DINGING ebe e aar Ee Eet EA ahi Ee 74 ShoWwip dhep Snooping EE 75 show ip dhcp snooping information 0 cccccceceeceececeeeceeeeeeeceeeaeeeeeeeesecneneaeeeeeeeesssesuseaeeeeees 75 show ip dhcp snooping interface c ccccecceeeeeeeeneaeeeeeeeeeecececeeeceeeeeeeeeecceseaeeeeeeeseseeneaneess 76 Chapter 13 ARP Inspection COMMAanNdS ooocccccccccccononannnnncccnenennnanannnnnnnnnnnnnnnananans 77 ip arp inspection global T a a a aa a aE ea E aaie 77 SR Re egen GE 77 ip arp inspection interface oooooccccnconocononococcncccnnnnnnonnnnnonocnononnnnnnnnnnnnnonannnnnnnnnnnnninnnnnnnnnnnnninens 78 ip arp inspection Immtt rate AANER 79 IP APP INSPECTOR a A 79 SNOW Ip ATP OS POCO ii A A AA A ee 80 show ip arp inspection interface ccccccecceeeeeeceneaeeeeeeeeeeeceneneaeeeceeeseeeceaeaeeeseeeeeeeesnseneeees 80 Show ip arp inspection statistics ooooocoonconnconononaconaconoconononcnonnnonoconononononono
168. nononononononnconnnnnncnnns 81 clear ip arp inspection statistics cece cee ceeeeeeeeeee ects cease eae eeaeeeaeeaaeaaaeaaaeaaaeeaaeaaeeaaaeaaaeaaaeaaes 81 Chapter 14 IP Verify Source Commande EEN NEn 82 leg ee 82 SHOW Ip Verify SUr e E 83 Chapter 15 DoS Defend CoOMMAnNd cccooonnnnnnnnccecececononanannncnononennnanannnnnnnenenennnananans 84 de Ree Cen EE 84 Ip dossprevent ele iia ent alive 84 ip d s prevent syn rate iii EE ee ig ei Se a 85 IP GOS PrEVENE e 86 Ip dos prevent detect EE 87 clear ip dos prevent detect statistics nnne cee ease sees aaee sees aaeeaaeeaaeeaaeeaaeeaaeeaaeeaaeeaes 87 SHOW ip AOS prevent cra eessen deene gege SES EES oid ds Telus ees d e geed dE 88 Chapter 16 IEEE 802 1X Commands ccoooonnnnnnncccccccnnnnnnannnnnnncnnnnnnnananannnenennnnnnnnnnns 89 le ak Een re WEE 89 dot1x auth Method WEE 89 dot1x guest vlan global isrener eN 90 ele at de UI enee EN 91 ele ot le jst A a ba ee aidan Jn ne eet Reel bee aidan sh net ng ee 91 doti max reath EA E 92 ele ek E 92 dot e EE 93 leie a port CONtTO EE 94 dott port mMmethod EE 94 Tale tege eege Ee ON 95 le ee 96 Show dot e ee EE 97 Ge dee ak ll Le 97 SNOW radis ACCOUNTING E 98 show radius authentication ce eee eee eee eeeeeeee cece ease eae a ease eae EEEE EEEEEEEE EEEE EEEEEEEE EEEE EEEE EEEE EEEE 98 Chapter 17 System Log Commandes EEn 99 JOGGING DU ii o Rann oe Be A intestate 99 logging file UE EE 100 Clear lOGGING EE 100
169. ntax show snmp server view 228 TL SL5428E BA 6 KY LL a EME EG e m EE TT IT Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the View table TL SL5428E show snmp server view show snmp server group Description The show snmp server group command is used to display the Group table Syntax show snmp server group Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Group table TL SL5428E show snmp server group show snmp server user Description The show snmp server user command is used to display the User table Syntax show snmp server user Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the User table TL SL5428E show snmp server user 229 TL SLSA7pERIGCEIORRKR EIET DL Eli e m EE ETT IT show snmp server community Description The show snmp server community command is used to display the Community table Syntax show snmp server community Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Community table TL SL5428E show snmp server community show snmp server host Description The show snmp server host command is used to display the Host table Syntax show snmp server host Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Host table TL SL5428E show snmp server host show snmp server enginelD Description The show snmp ser
170. nter into the User EXEC Mode Now you can manage your switch with CLI commands through Telnet connection 4 Type enable command to enter Privileged EXEC Mode A password that you have set through Console port connection is required Here the password is set as 123 e Telnet 192 168 0 1 ox bonoonoonococcnoe sonooooooocoscnocone User Access Login User admin Password TL SL5428E gt enable Password TL SL5428EH Figure 1 10 Enter to the Privileged EXEC Mode gt Login Mode Firstly configure the Telnet login mode as login and both the connection password and the Privileged EXEC Mode password as 123 in the prompted DOS screen shown in Figure 1 11 TL SL5428E RIIT MIA EEN EG e BRETT tp link HyperTerminal File Edit View Call Transfer Help De o mp TL SL5428E gt enable TL SL5428E config TL SL5428E config line vty 5 TL SL5428E config line login lt set login mode set connection password TL SL5428E config line password 1234 TL SL5428E config line exit set password for TL SL5428E config enable password 1234 entering Privileged EXEC Mode Figure 1 11 Configure login mode Now you can logon by Telnet in login mode 1 Open Telnet then type telnet 192 168 0 1 in the command prompt shown as Figure 1 12 and press the Enter button Figure 1 12 Connecting to the Switch 2 You are prompted to enter the connection password 123 you have set throu
171. o show the latest 20 commands you entered since the switch is powered Syntax show history 17 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Command Mode Privileged EXEC Mode and any Configuration Mode Example Show the commands you have entered before TL SL5428E config if show history TL SL5428E 1 show history clear history Description The clear history command is used to clear the commands you have entered before therefore these commands will not be shown next time you use the show history command Syntax clear history Command Mode Privileged EXEC Mode and any Configuration Mode Example Clear the commands you have entered before TL SL5428E config if clear history TL SL5428E config if 18 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter3 IEEE 802 1Q VLAN Commands VLAN Virtual Local Area Network technology is developed for the switch to divide the LAN into multiple logical LANs flexibly Hosts in the same VLAN can communicate with each other regardless of their physical locations VLAN can enhance performance by conserving bandwidth and improve security by limiting traffic to specific domains vian Description The vlan command is used to create IEEE 802 1Q VLAN hereafter to access to VLAN Configuration Mode To delete the IEEE 802 1Q VLAN please use no vlan command Syntax vlan vian list no vlan Vian l
172. obal rate The value to specify the maximum amount of DHCP messages that can be forwarded by the switch per second The excessive messages will be discarded The options are 0 10 20 30 40 50 packet second By default it is O standing for disable dec threshold The value to specify the minimum transmission rate of the Decline packets to trigger the Decline protection for the specific port The options are 0 5 10 15 20 25 30 packet second By default it is 0 standing for disable dec rate The value to specify the Decline Flow Control The traffic flow of the corresponding port will be limited to be this value if the transmission rate of the Decline packets exceeds the Decline Threshold The options are 5 10 15 20 25 30 packet second By default it is 5 Command Mode Global Configuration Mode Example Configure the Global Flow Control as 30pps the Decline Threshold as 20 pps and decline Flow Control as 20 pps for DHCP Snooping TL SL5428E config ip dhcp snooping global global rate 30 dec threshold 20 dec rate 20 ip dhcp snooping information option Description The ip dhcp snooping information option command is used to enable the Option 82 function of DHCP Snooping To disable the Option 82 function please use no ip dhcp snooping information option command Syntax ip dhcp snooping information option 69 TL SL5428E BA 6 0 5 1 a VET Xe DL EG e m EE TT IT no ip dhcp snooping informat
173. ocess mode alert port based recovery mode auto manual Parameter process mode The mode how the switch processes the detected loops alert when a loop is detected display an alert port based when a loop is detected display an alert and block the port recovery mode The mode how the blocked port recovers to normal status auto block status can be automatically removed after recovery time manual block status can only be removed manually Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure the loopback detection process mode as port based and recovery mode as manual for Gigabit Ethernet port 25 TL SL5428E config interface gigabitEthernet 1 0 25 TL SL5428E config if loopback detection config process mode port based recovery mode manual 163 TL SLSA7pERIGCEIORRKR EIET DL Eli e m EE ETT IT loopback detection recover Description The loopback detection recover command is used to remove the block status of selected ports recovering the blocked ports to normal status Syntax loopback detection recover Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Recover the blocked Gigabit Ethernet port 25 to normal status TL SL5428E config interface gigab
174. ode Global Configuration Mode Example To enter the Interface fastEthernet Configuration Mode and configure Fast Ethernet port 2 TL SL5428E config interface fastEthernet 1 0 2 interface range fastEthernet Description The interface range fastEthernet command is used to enter the interface range fastEthernet Configuration Mode and configure multiple Fast Ethernet ports at the same time Syntax interface range fastEthernet port list Parameter port list The list of Fast Ethernet ports Command Mode Global Configuration Mode 136 TL SL5428E Ent L A EEES e m EE ETT IT User Guidelines Command in the Interface Range fastEthernet Mode is executed independently on all ports in the range It does not effect the execution on the other ports at all if the command results in an error on one port Example To enter the Interface Range fastEthernet Configuration Mode and configure ports 1 2 3 6 7 and 9 at the same time by adding them to one port list TL SL5428E config interface range fastEthernet 1 0 1 3 1 0 6 7 1 0 9 interface gigabitEthernet Description The interface gigabitEthernet command is used to enter the interface gigabitEthernet Configuration Mode and configure the corresponding Gigabit Ethernet port Syntax interface gigabitEthernet port Parameter port The Fast Gigabit Ethernet port number Command Mode Global Configuration Mode Example To enter the Interface gigabitEthernet Config
175. ommand Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of a policy named policy1 TL SL5428E show access list policy policy1 show access list bind Description The show access list bind command is used to display the configuration of Policy bind 180 TL SLS4A7pERIGOCEIKROEIET D EC Oe REI Syntax show access list bind Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of Policy bind TL SL5428E show access list bind 181 TL SL5428E BAG 6 KY LLE aE Tare Xe DL Eli e BRETT Chapter 28 MSTP Commands MSTP Multiple Spanning Tree Protocol compatible with both STP and RSTP and subject to IEEE 802 1s can disbranch a ring network STP is to block redundant links and backup links as well as optimize paths spanning tree global Description The spanning tree command is used to enable STP function globally To disable the STP function please use no spanning tree command Syntax spanning tree no spanning tree Command Mode Global Configuration Mode Example Enable the STP function TL SL5428E config spanning tree spanning tree interface Description The spanning tree command is used to enable STP function for a port To disable the STP function please use no spanning tree command Syntax spanning tree no spanning tree Command Mode Interface Configuration Mode interface fastEthernet interface range
176. ommand is used to display the Multicast Filter Address table 211 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Syntax show ip igmp snooping filter filter adar id lisf Parameter filter addr id list The multicast ID selected to display the multicast filter address information It is optional Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display all the multicast filter address information TL SL5428E config show ip igmp snooping filter show ip igmp snooping querier vian Description The show ip igmp snooping querier vlan command is used to display the configurations of IGMP Snooping Querier of the specified VLAN Syntax show ip igmp snooping querier vlan vian list Parameter vian list The ID of the VLAN selected to display the configurations of IGMP Snooping Querier It is multi optional Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configurations of IGMP Snooping Querier of VLAN 2 4 and 5 TL SL5428E config show ip igmp snooping querier vlan 2 4 5 show ip igmp snooping querier Description The show ip igmp snooping querier vlan command is used to display the IGMP Snooping Querier configurations of all VLANs Syntax show ip igmp snooping querier 212 TL SL5428E BAG 6 icy Ts a Taree D EC Oe BRETT E Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configurations of IGMP Snooping Q
177. on The switchport voice vlan security command is used to enable the Voice VLAN security feature To disable the Voice VLAN security feature please use no switchport voice vlan security command Syntax switchport voice vlan security no switchport voice vlan security Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the Fast Ethernet port 3 for Voice VLAN security feature TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if switchport voice vlan security 41 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT show voice vlan Description The show voice vlan command is used to display the global configuration information of Voice VLAN Syntax show voice vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of Voice VLAN globally TL SL5428E config show voice vlan show voice vlan oui Description The show voice vlan oui command is used to display the configuration information of Voice VLAN OUI Syntax show voice vlan oui Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration information of Voice VLAN OUI TL SL5428E config show voice vlan oui 42 TL SL5428E BA 6 KY LLE a VET Xe DL Eli e BRETT show voice vlan switchport Description The s
178. on Mode Example Configure the DST start time as 00 00 am on April 1 the end time as 00 00 am on October 1 and the offset as 30 minutes TL SL5428E config system time dst date Apr 1 00 00 Oct 1 00 00 30 122 TL SL5428E BA 6 0 5 1 a VET Xe DL EG e BRETT system time dst recurring Description The system time dst recurring command is used to specify the DST configuration in recurring mode This configuration is recurring in use The time period is not restricted to be within one year Syntax system time dst recurring sweek sday smonth stime eweek eday emonth etime offset Parameter sweek Week to start with the options first second third fourth last sday Day to start with the options Sun Mon Tue Wed Thu Fri Sat smonth Month to start with options Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec stime Time to start in the format of hh mm eweek Week to end with options first second third fourth last eday Day to end with options Sun Mon Tue Wed Thu Fri Sat emonth Month to end with options Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec etime Time to end in the format of hh mm offset Specify the time adding in minutes when Daylight Saving Time comes The range of value depends and the default value is 60 minutes It is optional Command Mode Global Configuration Mode Ex
179. onfiguration Commands can be used to configure the system information and system IP of the switch and to reboot and reset the switch upgrade the switch system and commands used for device diagnose including loopback test and cable test system time manual Description The system time manual command is used to configure the system time manually Syntax system time manual time Parameter time Set the date and time manually in the format of MM DD YYYY HH MM SS Command Mode Global Configuration Mode Example Configure the system time as 02 14 2012 12 30 00 TL SL5428E config system time manual 02 14 2012 12 30 00 system time ntp Description The system time ntp command is used to configure the time zone and the IP Address for the NTP Server The switch will get UTC automatically if it has connected to a NTP Server Syntax system time ntp timezone ntp server backup ntp server fetching rate Parameter timezone Your local time zone and it ranges from UTC 12 00 to UTC 13 00 The detailed information that each time zone means are displayed as follow 119 TL SL5428E MOSCA EME El le BRETT UTC 12 00 TimeZone for International Date Line West UTC 11 00 TimeZone for Coordinated Universal Time 11 UTC 10 00 TimeZone for Hawaii UTC 09 00 TimeZone for Alaska UTC 08 00 TimeZone for Pacific Time US Canada UTC 07 00 TimeZone for Mountain Ti
180. onfiguration files from TFTP server with the IP 192 168 0 148 and name this file config TL SL5428E copy startup config tftp ip address 192 168 0 148 filename config copy tftp startup config Description The copy tftp startup config command is used to download the configuration file to the switch from TFTP server Syntax copy tftp startup config ip address p addr filename name Parameter ip addr IP Address of the TFTP server name Specify the name for the configuration file which would be downloaded Command Mode Privileged EXEC Mode 129 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Example Download the configuration file named as config to the switch from TFTP server with the IP 192 168 0 148 TL SL5428E copy tftp startup config ip address 192 168 0 148 filename config firmware upgrade Description The firmware upgrade command is used to upgrade the switch system file via the TFTP server Syntax firmware upgrade ip address p addr filename name Parameter ip addr IP Address of the TFTP server name Specify the name for the firmware file Command Mode Privileged EXEC Mode Example Upgrade the switch system file named as firmware bin from the TFTP server with the IP address 192 168 0 148 TL SL5428E firmware upgrade ip address 192 168 0 148 filename firmware bin ping Description The ping command is used to test the connectivity between the switch and one
181. oping multi vlan config ooooccccocccccocononaccncncncnncnnonrnnnnnnononcnnnnnnnnnnnnnnnnnnnnnnnnncnnnno 202 ip igmp snooping filter ad 203 ip igmp snooping fliertolobalt rner erttnnnn nnee enee 204 ip igmp snooping filter interface oooocococnncnninicicccccnnoccnnnanananncononnoncnnrn ono nnnnononcnnnnnnnnnnnaninnns 204 ip igmp snooping filter maxvgroup nono nnnnnnancnnnnnnnnnnnaninnns 205 ip igmp snooping filter mode 205 ip igmp snooping querier van 206 ip igmp snooping querier vlan general QUETY cocccccccccconcoccncccnnccncnnnannncnnnnnononnannnnnnnnoneninnas 207 ip igmp snooping querier vlan specific query ooccccccicocococccncncccnnnnancnnnnnnnononnnnnnnnnnnnnonnnnas 208 SNOW IPIGMP SNOOPING EE 209 show ip igmp snooping Interface 209 Show ip iQMp SNOOPING VIAN ie ar nein ieee 210 Show ip mp snooping multt vlan 210 show IP mp SNOOPING QTOUPS irira ieii eaea aeie aa T ET EE a AEEA EEE AAE EEEE Ea eai 211 show ip igmp snooping filter 0 0 2 2 eee eee ceeccece cece eeeeeeeeeeeeeeeeeeeeceeeaaeeeeeeeesesenccneeeeeeeeeesesneneaeeees 211 show ip igmp snooping querier VIAN eenean 212 Show ip iQMp Snooping Ouere 212 Chapter 30 SNMP CoMMAanNdS oooonnnnccccccccnonononcnnnoncnoncnnnnnannnnnnnnnnnnnnnnnannnnnnrennnnennnns 214 SINIMP SOPVOP icc condones A A E 214 nl 214 SNMP SErVEr Groups d ier A A nen Ae Ne e EE 215 SOM PESE USER A ee A A eee eae 216 SNMP Server COMMUNIty EE 218 lune E 219 snmp server enginel
182. ormation of all the Ethernet ports is displayed Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the GVRP configuration information of Fast Ethernet port 1 TL SL5428E config show gvrp interface fastEthernet 1 0 1 Display the GVRP configuration information of all Ethernet ports TL SL5428E config show gvrp interface 52 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Chapter 10 Etherchannel Commands Etherchannel Commands are used to configure LAG and LACP function LAG Link Aggregation Group is to combine a number of ports together to make a single high bandwidth data path which can highly extend the bandwidth The bandwidth of the LAG is the sum of bandwidth of its member port LACP Link Aggregation Control Protocol is defined in IEEE802 3ad and enables the dynamic link aggregation and disaggregation by exchanging LACH packets with its partner The switch can dynamically group similarly configured ports into a single logical link which will highly extend the bandwidth and flexibly balance the load channel group Description The channel group command is used to add a port to the EtherChannel Group and configure its mode To delete the port from the EtherChannel Group please use no channel group command Syntax channel group num mode on active passive no channel group Parameter num The number of the EtherChannel Group ranging from 1 to 14 on Enable the static
183. p It is sent when the rate limit function is enabled and the bandwidth exceeds the predefined value cpu Allow CPU related trap It is sent when CPU usage exceeds the predefined threshold By default the CPU usage threshold of the switch is 80 flash Enable flash trap It is sent when flash is modified during operations such as backup reset firmware upgrade configuration import etc 222 TL SL5428E BA 6 0 5 1 a VET Xe DL Eli e BRETT ipaddr change Enable ipaddr change trap It is sent when IP address is changed such as user manually modifies the IP address or the switch obtains a new IP address from DHCP Ildp Enable lldp trap It is sent when the port s neighbor changes loopback detection Enable loopback detection trap It is sent when the switch detects loopback or loopback is cleared storm control Enable storm control trap It is sent when the multicast or broadcast rate exceeds the predefined value spanning tree Enable spanning tree trap It is sent when the port forwarding status changes or the port receives TCN packet or packet with TC flag memory Enable memory trap It is sent when CPU usage exceeds 80 Command Mode Global Configuration Mode Example Enable SNMP extended bandwidth control trap for the switch TL SL5428E config snmp server traps bandwidth control snmp server traps mac Description The snmp server traps mac command is used to en
184. p server traps vlan command Syntax snmp server traps vlan create delete no snmp server traps vlan create delete Parameter create Enable VLAN created trap It is sent when new VLAN is created successfully delete Enable VLAN deleted traps It is sent when VLAN is deleted successfully Command Mode Global Configuration Mode Example Enable all SNMP extended VLAN related traps for the switch TL SL5428E config snmp server traps vian Enable VLAN created trap only for the switch TL SL5428E config snmp server traps vlan create 224 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT rmon history Description The rmon history command is used to configure the history sample entry To return to the default configuration please use no rmon history command RMON Remote Monitoring basing on SNMP architecture functions to monitor the network History Group is one of the commonly used RMON Groups After a history group is configured the switch collects network statistics information periodically based on which the management station can monitor network effectively Syntax rmon history index interface fastEthernet port gigabitEthernet port interval seconds owner owner name no rmon history index Parameter index The index number of the entry ranging from 1 to 12 in the format of 1 3 5 port The Fast Gigabit Ethernet port number seconds The interval to take s
185. p snooping information remote id command Syntax ip dhcp snooping information remote id string no ip dhcp snooping information remote id Parameter string Enter the sub option Remote ID which contains 32 characters at most Command Mode Global Configuration Mode Example Enable and configure the customized sub option Remote ID for the Option 82 as tplink TL SL5428E config ip dhcp snooping information remote id tplink ip dhcp snooping information circuit id Description The ip dhcp snooping information circuit id command is used to enable and configure the customized sub option Circuit ID for the Option 82 To return to the default Circuit ID for the Option 82 please use no ip dhcp snooping information circuit id command Syntax ip dhcp snooping information circuit id string no ip dhcp snooping information circuit id 71 TL SL5428E MOSCA EME EG e M EE ETT IT Parameter string Enter the sub option Circuit ID which contains 32 characters at most Command Mode Global Configuration Mode Example Enable and configure the customized sub option Circuit ID for the Option 82 as tplink TL SL5428E config ip dhcp snooping information circuit id tplink ip dhcp snooping trust Description The ip dhcp snooping trust command is used to configure a port to be a Trusted Port Only the Trusted Port can receive the DHCP packets from DHCP servers To turn the port back to a distrusted port
186. ple Display the internal LACP information of EtherChannel Group 1 TL SL5428E config show lacp 1 internal show lacp sys id Description The show lacp sys id command is used to display the LACP system priority globally Syntax show lacp sys id Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LACP system priority TL SL5428E config show lacp sys id 57 Chapter 1 TL SL5428E BA 6 0 5 1 aE TATT Xe Eli e M EE ETT IT 1 User Manage Commands User Manage Commands are used to manage the user s logging information by Web CLI or SSH so as to protect the settings of the switch from being randomly changed user name Description Syntax Parameter Command Example The user name command is used to add a new user or modify the existed users information To delete the existed users please use no user name command user name user name password password type guest admin status disable enable secret simple cipher no user name user name Username Type a name for users login which contains 16 characters at most composing digits English letters and under dashes only password Type a password for users login which contains 31 characters at most composing digits English letters and under dashes only guest admin Access level Guest means that you can only view the settings without the right to edit and modify Admin me
187. pose the identifier of the SNMP Group These three items of the Users in one group should be the same 215 TL SL5428E BA 6 0 5 1 a VET Xe DL EG e m EE ETT IT smode Security Model with v1 v2c and v3 options They represent SNMP v1 SNMP v2c and SNMP v3 slev The Security Level of SNMP v3 Group There are three options including noAuthNoPriv no authorization and no encryption authNoPriv Cauthorization and no encryption and authPriv authorization and encryption By default the Security Level is noAuthNoPriv There is no need to configure this in SNMP v1 Model and SNMP v2c Model read Read only view The management access is restricted to read only and changes cannot be made to the assigned SNMP View write Write only view The management access is writing only and changes can be made to the assigned SNMP View The View defined both as the Read View and the Write View can be read and modified notify Notify view The management station software can receive trap messages of the assigned SNMP view generated by the Switch s SNMP agent Command Mode Global Configuration mode Example Add group 1 and configure the Security Model as SNMP v3 the security level as authNoPriv the management access to the assigned View viewDefault as read write besides the trap messages sent by View viewDefault can be received by Management station TL SL5428E config snmp server group group1 s
188. redirect interface fastEthernet port gigabitEthernet port Parameter port The Destination Port of Redirect The data packets matching the corresponding ACL will be forwarded to the specific port By default it is All Ports Command Mode Action Configuration Mode Example Edit the actions for policy1 Forward the data packets matching ACL 120 in the policy to Fast Ethernet port 2 TL SL5428E config access list policy action policy1 120 TL SL5428E config action redirect interface fastEthernet 1 0 2 redirect vian Description The redirect vlan command is used to configure Direction function of policy action for specified VLAN Syntax redirect vian vian id 175 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Parameter vian id The VLAN ID of Redirect The data packets matching the corresponding ACL will be forwarded in the specific VLAN The VLAN ID ranges from 1 to 4094 Command Mode Action Configuration Mode Example Edit the actions for policy1 Forward the data packets matching ACL 120 in the policy to Fast Ethernet VLAN 1 TL SL5428E config access list policy action policy1 120 TL SL5428E config action redirect vlan 1 s condition Description The s condition command is used to configure Stream Condition function of policy action Syntax s condition rate rate osd none discard Parameter rate The rate of Stream Condition ranging from 0 to 1
189. rface ooooococccccooccccccccccocanonncnccnnnnonnnnnnncnncnnnnos 116 show mac address table Interface 117 show mac address table COUN eee eee nnnn nono nnnnnnnn nn none nonnnnnnnnnnnos 117 show mac address table address 117 show mac address table van 118 Chapter 21 System Configuration Commande ken 119 system time Lu EC 119 SYSLSM UME MID aad is Ae AAR ete Seg aed ais At edad Aiea 119 system time dst predefined ccccccecceccece cece ceeeeeeecneeceeeeeeeeeeceeeaeeeeeeeesesccieaeeeeeeeeeeseeneaees 121 System timeASt date sas ses ods etc a deed gen d bee See e 122 system time det recurring AAA 123 We ln EEN 124 eler IER 124 contacto odian 125 p management VAN aa epa 125 PAS e A EE ee 126 ip address alot AHP ai AER 126 Ip address allOG DOOD TER 127 POSCU E 127 FEDER laca 128 copy running config startup config ooooocococcccncccccnnnononcnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnonnnnnnnnnncnnnno 128 copy Stanmtup Contig tht ire eege oe 129 COPY tftp Start p config EEN 129 firmware Upgrade ii San area e eae 130 elle VE 130 UE 131 VII loopback interface EE 132 show svstem Hme ee eee deanna 132 show system time det 133 SHOW SYSLSMAtIMG NIP acces r a a ati 133 Show SyStemeinto s r ad oe ee AAA A ed A is 134 SHOW TUNNING CONPIG EE 134 show cable diagnostics Interface 135 Chapter 22 Ethernet Configuration Commande KEEN 136 interface fastEthernet A 136 interface range fastEthernet
190. rmation and System IP reboot and reset the switch upgrade the switch system and commands used for device diagnose including loopback test and cable test Chapter 22 Ethernet Configuration Commands Provide information about the commands used for configuring the Bandwidth Control Negotiation Mode and Storm Control for ethernet ports TL SL5428E BAG 6 0 5 1 KREIEN le BRETT Chapter 23 QoS Commands Provide information about the commands used for configuring the QoS function Chapter 24 Port Mirror Commands Provide information about the commands used for configuring the Port Mirror function Chapter 25 Port isolation Commands Provide information about the commands used for configuring the Port isolation function Chapter 26 Loopback Detection Commands Provide information about the commands used for loopback detection Chapter 27 ACL Commands Provide information about the commands used for configuring the ACL Access Control List Chapter 28 MSTP Commands Provide information about the commands used for configuring the MSTP Multiple Spanning Tree Protocol Chapter 29 IGMP Commands Provide information about the commands used for configuring the IGMP Snooping Internet Group Management Protocol Snooping Chapter 30 SNMP Commands Provide information about the commands used for configuring the SNMP Simple Network Management Protocol functions Chapter 31 LLDP Commands Provide information about the commands
191. rom 1 to 300 Seconds By default it is 60 seconds response time The maximal time for the host to respond to a general query frame ranging from 1 to 25 Seconds By default it is 10 Seconds ip addr The source IP of the general query frame sent by IGMP Snooping Querier lt should not be a multicast IP or a broadcast IP By default it is 192 168 0 1 Command Mode Global Configuration Mode Example For VLAN 2 specify its query interval as 200 seconds and the response time as 20 seconds TL SL5428E config ip igmp snooping querier vlan 2 query interval 200 TL SL5428E config ip igmp snooping querier vlan 2 max response time 20 207 TL SL5428E BA 6 LLE aE Tare Xe DL Eli e m EE ETT IT ip igmp snooping querier vian specific query Description The ip igmp snooping querier vlan command is used to configure the parameters for IGMP Snooping Querier to send a specific query frame To return to the default configuration please use no ip igmp snooping querier vlan command Syntax ip igmp snooping querier vlan vian list last member query interval interval last member query count count special query source ip p addr no ip igmp snooping querier vlan vian list last member query interval last member query count special query source ip Parameter vlan list VLAN ID list ranging from 1 to 4094 in the format of 1 3 5 It is multi optional interval The time interval of sending specific que
192. rtant events that occur on the Views which allows the management station to monitor and process the events in time Syntax snmp server host ip udp port user name smode v1 v2c v3 slev noAuthNoPriv authNoPriv authPriv type trap inform H retries retries timeout timeout no snmp server host p user name Parameter ip The IP Address of the management Host udp port UDP port which is used to send notifications The UDP port functions with the IP address for the notification sending By default it is 162 user name The User name of the management station smode The Security Model of the management station with v1 v2c and v3 options By default the option is v1 slev The Security Level of SNMP v3 Group There are three options including noAuthNoPriv no authorization and no encryption authNoPriv authorization and no encryption and authPriv authorization and encryption By default the option is noAuthNoPriv type The type of the notifications with trap and inform options Trap indicates traps are sent while inform indicates informs are sent The inform type has a higher security than the trap type and resend and timeout need to be configured if you select this option You can only select the trap type in Security Model v1 By default the type of the notifications is trap retries The amount of times the switch retries an inform
193. rts taking up too much bandwidth Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Specify the maximum number of multicast groups for Fast Ethernet ports 2 5 to join in as 10 TL SL5428E config interface range fastEthernet 1 0 2 5 TL SL5428E config if range ip igmp snooping filter maxgroup 10 ip igmp snooping filter mode Description The ip igmp snooping filter mode command is used to configure the Action mode for the desired port Syntax ip igmp snooping filter mode mode 205 TL SL5428E Ent L A EEES e m EE ETT IT Parameter mode Action Mode with refuse and accept options Refuse indicates only the multicast packets whose multicast IP is not in the IP range will be processed while accept indicates only the multicast packets whose multicast IP is in the IP range will be processed By default the option is accept Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Specify the Action Mode as accept for Fast Ethernet port 3 TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if ip igmp snooping filter mode accept ip igmp snooping querier vlan Description The ip igmp snooping querier vlan command is used to enable t
194. ry frames by IGMP Snooping Querier ranging from 1 to 5 Seconds By default it is 1 A specific query will be sent on condition that immediate leave is not enabled and a leave frame is received count The times of sending specific query frames by IGMP Snooping Querier ranging from 1 to 5 By default it is 2 The switch will still treat the port as group member until the specific frames number sent by the querier reaches last member query count and no report frame is received from the port ip addr The source IP of the specific query frame sent by IGMP Snooping Querier It should not be a multicast IP or a broadcast IP By default it is 192 168 0 1 Command Mode Global Configuration Mode Example For VLAN 2 specify its last member query interval as 2 TL SL5428E config ip igmp snooping querier vlan 2 last member query interval 2 208 TL SL5428E BAG 6 0 5 1 a VET Xe DL EG e BRETT show ip igmp snooping Description The show ip igmp snooping command is used to display the global configuration of IGMP Snooping Syntax show ip igmp snooping Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of IGMP Snooping TL SL5428E show ip igmp snooping show ip igmp snooping interface Description The show ip igmp snooping interface command is used to display the port configuration of IGMP Syntax show ip igmp snooping interface fastEther
195. s Figure 1 4 Port Settings TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide 6 The DOS prompt TL SL5428E gt will appear after pressing the Enter button as Figure 1 5 shown It indicates that you can use the CLI now tp tink HyperTerminal Figure 1 5 Log in the Switch 1 1 2 Logon by Telnet To successfully create Telnet connection firstly CLI commands about configuring Telnet login mode login authentication information and Privileged EXEC Mode password should be configured through Console connection Telnet login has the following two modes you can choose one according to your needs Login Local Mode It requires username and password which are both admin by default Login Mode It requires no username and password but a connection password is required Note 1 Before Telnet login you are required to configure Telnet login mode and login authentication information through Console connection The relevant CLI commands should be entered in the prompted DOS screen shown in Figure 1 5 Log in the Switch 2 You will enter to User EXEC Mode after Telnet connection is successfully created but for switch security concerns you are required to set a password which functions to further access to Privileged EXEC Mode when you configure the login mode gt Login Local Mode Firstly configure the Telnet login mode as login local and set the password for entering into the
196. s can be added or removed manually independent of the aging time In the stable networks the static MAC address entries can facilitate the switch to reduce broadcast packets and enhance the efficiency of packets forwarding remarkably Syntax mac address table static mac addr vid vid interface fastEthernet port gigabitEthernet port no mac address table static mac addr vid vid mac mac addr vid vid interface fastEthernet port gigabitEthernet port Parameter mac addr The MAC address of the entry you desire to add vid The VLAN ID number of your desired entry lt ranges from 1 to 4094 port The Fast Gigabit Ethernet port number Command Mode Global Configuration Mode Example Add a static Mac address entry to bind the MAC address 00 02 58 4f 6c 23 VLAN1 and Fast Ethernet port 1 together TL SL5428E config mac address table static 00 02 58 4f 6c 23 vid 1 interface fastEthernet 1 0 1 Delete the static address entry whose VLAN id is 1 TL SL5428E config no mac address table static vid 1 Delete the static address entry whose MAC address is 00 02 58 4f 6c 23 112 TL SL5428E BAG 6 LLE a EME Eli e BRETT TL SL5428E config no mac address table static 00 02 58 4f 6c 23 mac address table aging time Description The mac address table aging time command is used to configure aging time for the dynamic address To return to the default configuration please use no mac address table aging t
197. s prevent ping rate command is used to configure the transmission rate of the Ping packets To restore to default please use no ip dos prevent ping rate command Syntax ip dos prevent ping rate ping rate no ip dos prevent ping rate 84 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Parameter ping rate Specify the transmission rate of the Ping packets when the Defend Type Ping Flooding is enabled The options are 128k 256k 512k 1m 2m 4m in bps By default the value is 128k Command Mode Global Configuration Mode Example Specify the transmission rate of the Ping packets as 256k TL SL5428E config ip dos prevent ping rate 256k ip dos prevent syn rate Description The ip dos prevent syn rate command is used to configure the transmission rate of the SYN SYN ACK packets To restore to default please use no ip dos prevent syn rate command Syntax ip dos prevent syn rate syn rate no ip dos prevent syn rate Parameter syn rate Specify the transmission rate of the SYN SYN ACK packets when the Defend Type SYN SYN ACK Flooding is enabled The options are 128k 256k 512k 1m 2m 4m in bps By default the value is 128k Command Mode Global Configuration Mode Example Specify the transmission rate of the SYN SYN ACK packets as 1m TL SL5428E config ip dos prevent syn rate 1m 85 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT ip dos prevent type Description The ip dos prevent type
198. s used to configure the Control Mode of IEEE 802 1X for the specified port By default the control mode is auto To restore to the default configuration please use no dot1x port control command Syntax dot1x port control auto authorized force unauthorized force no dot1x port control Parameter auto authorized force unauthorized force The Control Mode for the port auto In this mode the port will normally work only after passing the 802 1X Authentication authorized force In this mode the port can work normally without passing the 802 1X Authentication unauthorized force In this mode the port is forbidden working for its fixed unauthorized status Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure the Control Mode for Gigabit Ethernet port 25 as authorized force TL SL5428E config interface gigabitEthernet 1 0 25 TL SL5428E config if dot1x port control authorized force dot1x port method Description The dot1x port method command is used to configure the control type of IEEE 802 1X for the specified port By default the control type is mac based To restore to the default configuration please use no dot1x port method command 94 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Syntax dot1x port method mac based port based no dot
199. s will be removed Syntax instance instance id vlan vian id no instance instance id vlan vlan id Parameters instance id Instance ID ranging from 1 to 8 vian id The VLAN ID selected to mapping with the corresponding instance Command Mode MST Configuration Mode 185 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Example Map the VLANs 1 100 to Instance 1 TL SL5428E config spanning tree mst configuration TL SL5428E config mst instance 1 vlan 1 100 Disable Instance 1 namely remove all the mapping VLANs 1 100 TL SL5428E config spanning tree mst configuration TL SL5428E config mst no instance 1 Remove VLANs 1 50 in mapping VLANs 1 100 for Instance 1 TL SL5428E config spanning tree mst configuration TL SL5428E config mst no instance 1 vlan 1 50 name Description The name command is used to configure the region name of MST instance Syntax name name Parameters name The region name used to identify MST region It ranges from 1 to 32 characters Command Mode MST Configuration Mode Example Configure the region name of MST as region1 TL SL5428E config spanning tree mst configuration TL SL5428E config mst name region revision Description The revision command is used to configure the revision level of MST instance Syntax revision revision 186 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Parameters revision The rev
200. sing log indicates logging the event notify indicates sending trap messages to the management station and both indicates logging the event and sending trap messages to the management station owner name The owner of the event entry ranging from 1 to 16 characters By default it is monitor Command Mode Global Configuration Mode Example Configure the user name of entry 1 2 3 and 4 as user1 the description of the event as description1 the type of event as log and the owner of the event as owner TL SL5428E config rmon event 1 4 user user1 description description type log owner owner1 rmon alarm Description The rmon alarm command is used to configure SNMP RMON Alarm Management To return to the default configuration please use no rmon alarm command Alarm Group is one of the commonly used RMON Groups RMON alarm management allows monitoring the specific alarm variables When the 226 Syntax TL SL5428E MOSCA EEES le BRETT value of a monitored variable exceeds the threshold an alarm event is generated which triggers the switch to act in the set way rmon alarm index interface fastEthernet port gigabitEthernet port alarm variable drop revbyte revpkt bpkt mpkt crc lign undersize oversize fragment jabber collision 64 65 127 128 511 512 1023 1024 10240 Y s type absolute delta rising threshold r hold rising event ind
201. snooping drop unknown ip igmp snooping vlan config Description The ip igmp snooping vlan config command is used to enable VLAN IGMP Snooping function or to modify IGMP Snooping parameters and to create static multicast IP entry To disable the VLAN IGMP Snooping function please use no ip igmp snooping vlan config command Syntax ip igmp snooping vlan config vian list rtime router time mtime member time me eave time rport interface fastEthernet port gigabitEthernet port ip igmp snooping vlan config vian id static ip interface fastEthernet port gigabitEthernet port no ip igmp snooping vlan config vian id list no ip igmp snooping vlan config vian id static ip Parameter vlan list The ID list of the VLAN desired to modify configuration ranging from 2 to 4094 in the format of 1 3 5 router time Router Port Time Within this time if the switch does not receive IGMP query message from the router port it will consider this port is not a router port any more Router Port Time ranges from 60 to 600 in seconds By default it is 300 member time Member Port Time Within this time if the switch does not receive IGMP report message from the member port it will consider this port is not a member port any more Member Port Time ranges from 60 to 600 in seconds By default it is 260 leave time Leave Time which is the interval between the switch receiving a leave message from a host and the switch r
202. src dst mac lacp system priority Description The lacp system priority command is used to configure the LACP system priority globally To return to the default configurations please use no lacp system priority command Syntax lacp system priority pri no lacp system priority Parameter pri The system priority ranging from 0 to 65535 It is 32768 by default 54 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Command Mode Global Configuration Mode Example Configure the LACP system priority as 1024 globally TL SL5428E config lacp system priority 1024 lacp port priority Description The lacp port priority command is used to configure the LACP system priority globally To return to the default configurations please use no lacp port priority command Syntax lacp port priority pri no lacp port priority Parameter pri The port priority ranging from O to 65535 It is 32768 by default Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEhternet Example Configure the LACP port priority as 1024 for Fast Ethernet port 1 TL SL5428E config interface fastEthernet 1 0 1 TL SL5428E config if Hlacp port priority 1024 show etherchannel Description The show etherchannel command is used to display the EtherChannel information Syntax show etherchannel channel group num detail summary
203. ss p addr Parameter v1 v2 Select the type of SSH key to download v1 represents SSH 1 v2 represents SSH 2 key file The name of the key file which is selected to download The length of the name ranges from 1 to 25 characters The key length of the downloaded file must be in the range of 256 to 3072 bits ip addr The IP address of the TFTP server Command Mode Global Configuration Mode Example Download a SSH 1 type key file named ssh key from TFTP server with the IP Address 192 168 0 148 TL SL5428E config ip ssh download v1 ssh key ip address 192 168 0 148 show ip ssh Description The show ip ssh command is used to display the global configuration of SSH Syntax show ip ssh 107 TL SL5428E BAG 6 icy Ts a Taree D EC Oe BRETT E Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration of SSH TL SL5428E config show ip ssh 108 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Chapter 19 SSL Commands SSL Secure Sockets Layer a security protocol is to provide a secure connection for the application layer protocol e g HTTP based on TCP Adopting asymmetrical encryption technology SSL uses key pair to encrypt decrypt information A key pair refers to a public key contained in the certificate and its corresponding private key By default the switch has a certificate self signed certificate and a corresponding private key The Certifica
204. tEthernet 199 TL SL5428E BA 6 KT LL a VET Xe DL EG e m EE ETT IT Example Enable IGMP Snooping function of Gigabit Ethernet port 25 TL SL5428E config interface gigabitEthernet 1 0 25 TL SL5428E config if ip igmp snooping ip igmp snooping immediate leave Description The ip igmp snooping immediate leave command is used to configure the Fast Leave function for port To disable the Fast Leave function please use no ip igmp snooping immediate leave command Syntax ip igmp snooping immediate leave no ip igmp snooping immediate leave Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the Fast Leave function for Fast Ethernet port 3 TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if ip igmp snooping immediate leave ip igmp snooping drop unknown Description The ip igmp snooping drop unknown command is used to process the unknown multicast as discard To disable the operation of processing the unknown multicast as discard please use no ip igmp snooping drop unknown command Syntax ip igmp snooping drop unknown no ip igmp snooping drop unknown Command Mode Global Configuration Mode 200 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Example Specify the operation of processing unknown multicast as discard TL SL5428E config ip igmp
205. tchport dot1q tunnel mode uplink command is used to configure a specified port as the VPN Up link port To cancel this VPN Up link port please use the no switchport dot1q tunnel mode uplink command By default no port has been configured as the VPN Up link port Syntax switchport dot1q tunnel mode uplink no switchport dot1q tunnel mode uplink Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet 35 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Example Configure the Fast Ethernet port 3 as the VPN Up link ports TL SL5428E config interface fastEthernet 1 0 3 TL SL5428E config if switchport dot1q tunnel mode uplink show dot1q tunnel Description The show dotiq tunnel command is used to display the global configuration information of the VLAN VPN Syntax show dot1q tunnel Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global configuration information of the VLAN VPN TL SL5428E config show dot1q tunnel show dot1q tunnel mapping Description The show dot1q tunnel mapping command is used to display the information of VLAN Mapping entry Syntax show dot1q tunnel mapping Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the information of VLAN Mapping entry TL SL5428E config show dot1q tunnel mapping 36 TL SL5428E NI
206. te Key Download function enables the user to replace the default key pair ip http secure server Description The ip http secure server command is used to enable the SSL function globally on the switch To disable the SSL function please use no ip http secure server command Only the SSL function is enabled a secure HTTPS connection can be established Syntax ip http secure server no ip http secure server Command Mode Global Configuration Mode Example Enable the SSL function TL SL5428E config ip http secure server ip http secure server download certificate Description The ip http secure server download certificate command is used to download a certificate to the switch from TFTP server Syntax ip http secure server download certificate ss cert ip address p addr 109 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Parameter ssl cert The name of the SSL certificate which is selected to download to the switch The length of the name ranges from 1 to 25 characters The Certificate must be BASE64 encoded ip addr The IP address of the TFTP server Command Mode Global Configuration Mode Example Download a SSL Certificate named ssl cert from TFTP server with the IP Address of 192 168 0 146 TL SL5428E config ip http secure server download certificate ssl cert ip address 192 168 0 146 ip http secure server download key Description The ip http secure server download key comman
207. th Je return to Privileged EXEC mode ernet port or interface TL SL5428E config if Interface range fastEthernet Enter exit or command to return to Configuration i gabitEthernet port list TL SL5428E config if Global Configuration mode Mode g g P ee to ST SE range A port number must be specified in the mode rom oba interface command Configuration mode VUN Use the vlan vlan list Use the end command or press Ctrl Z to Gontiautatoh command to enter this TL SL5428E config return to Privileged EXEC mode Mode mode from Global vian Enter the exit or command to return to Configuration mode Global configuration mode Note 1 The user is automatically in User EXEC Mode after the connection between the PC and the switch is established by a console port or by a telnet connection 2 Each command mode has its own set of specific commands To configure some commands you should access the corresponding command mode firstly e Global Configuration Mode In this mode global commands are provided such as the Spanning Tree Schedule Mode and so on e Interface Configuration Mode In this mode users can configure one or several ports Different ports correspond to different commands a Interface fastEthernet gigabitEthernet Configure parameters for a Fast Gigabit Ethernet port such as Duplex mode flow control status b Interface range fastEthernet gigabitEthernet The commands contained are the same as that of the
208. the Event configuration of entry1 4 TL SL5428E show rmon event 1 4 show rmon alarm Description The show rmon alarm command is used to display the configuration of the Alarm Management entry Syntax show rmon alarm index Parameter index The index number of the entry selected to display the configuration ranging from 1 to 12 in the format of 1 3 5 You can select more than one entry for each command By default the configuration of all Alarm Management entries is displayed Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of the Alarm Management entry 1 2 TL SL5428E show rmon alarm 1 2 232 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Chapter 31 LLDP Commands LLDP function enables network devices to advertise their own device information periodically to neighbors on the same LAN The information of the LLDP devices in the LAN can be stored by its neighbor in a standard MIB so it is possible for the information to be accessed by a Network Management System NMS using SNMP Ildp Description The lldp command is used to enable LLDP function To disable the LLDP function please use no Ildp command Syntax lldp no lldp Command Mode Global Configuration Mode Example Enable LLDP function globally TL SL5428E config lldp Ildp hold multiplier Description The Ildp hold multiplier command is used to configure the Hold Multiplier p
209. the Line Configuration Mode and make related configurations for the desired user s including the login mode and password configurations Syntax line console inenum vty startlinenum endlinenum Parameter linenum The number of users allowed to login through console port Its value is 0 in general as there is only one console port on a switch startlinenum The start serial number of the login user selected to configure the login mode and password ranging from O to 15 O means the first login user number 1 means the second and the rest can be done on the same manner endlinenum The end serial number of the login user selected to configure the login mode and password ranging from O to 15 O means the first login user number 1 means the second and the rest can be done on the same manner Command Mode Global Configuration Mode Example Enter the Console port configuration mode and configure the console port 0 TL SL5428E config line console 0 62 TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Enter the Virtual Terminal configuration mode so as to prepare further configurations such as password and login mode for virtual terminal O to 5 TL SL5428E config line vty 0 5 password Description The password command is used to configure the connection password To clear the password please use no password command Syntax password password no password Param
210. thernet port gigabitEthernet port counters Parameter port The Fast Gigabit Ethernet port number By default the statistic information of all ports is displayed Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the statistic information of all Ethernet ports TL SL5428E config show interface counters Display the statistic information of Gigabit Ethernet port 25 TL SL5428E config show interface gigabitEthernet 1 0 25 counters 145 TL SL5428E BA 6 5 1 a EME EG e BRETT show interface description Description The show interface description command is used to display the description of all ports or an Ethernet port Syntax show interface fastEthernet port gigabitEthernet port description Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the description of all Ethernet ports TL SL5428E config show interface description show interface flowcontrol Description The show interface flowcontrol command is used to display the flow control information of an Ethernet port Syntax show interface fastEthernet port gigabitEthernet port flowcontrol Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the flow control information of all Ethernet ports TL SL5428E show interface flowcontrol 1
211. tically add or remove the VLANs via the dynamic VLAN registration information and propagate the local VLAN registration information to other switches without having to individually configure each VLAN gvrp Description The gvrp command is used to enable the GVRP function globally To disable the GVRP function please use no gvrp command Syntax gvrp no gvrp Command Mode Global Configuration Mode Example Enable the GVRP function globally TL SL5428E config gvrp gvrp interface Description The gvrp command is used to enable the GVRP function for the desired port To disable it please use no gvrp command The GVRP feature can only be enabled for the trunk type ports Syntax gvrp no gvrp 49 TL SL5428E BA 6 KY LLE a EME Eli e BRETT Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEhternet Example Enable the GVRP function for Fast Ethernet ports 2 6 TL SL5428E config interface range fastEthernet 1 0 2 6 TL SL5428E config if range gvrp gvrp registration Description The gvrp registration command is used to configure the GVRP registration type for the desired port To restore to the default value please use no gvrp registration command Syntax gvrp registration normal fixed forbidden no gvrp registration Parameter normal fixed forbidden Registration mode By de
212. tive Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the active information of spanning tree TL SL5428E config show spanning tree active show spanning tree bridge Description The show spanning tree bridge command is used to display the bridge parameters Syntax show spanning tree bridge forward time hello time hold count max age max hops mode priority state Command Mode Privileged EXEC Mode and Any Configuration Mode 195 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Example Display the bridge parameters TL SL5428E config show spanning tree bridge show spanning tree interface Description The show spanning tree interface command is used to display the spanning tree information of all ports or a specified port Syntax show spanning tree interface fastEthernet port gigabitEthernet port edge ext cost int cost mode p2p priority role state status Parameter port The Fast Gigabit Ethernet port number Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the spanning tree information of all ports TL SL5428E config show spanning tree interface Display the spanning tree information of Gigabit Ethernet port 25 TL SL5428E config show spanning tree interface gigabitEthernet 1 0 25 Display the spanning tree mode information of Gigabit Ethernet port 25 TL SL5428E config show spanning tree interface gigab
213. to 255 in seconds It is 20 by default interval time Interval Time which is the interval to send handshake packets Interval Time ranges from 1 to 255 in seconds It is 20 by default Command Mode Global Configuration Mode Example Specify the Hold Time and Interval Time of the cluster as 50 seconds TL SL5428E config cluster manage holdtime 50 TL SL5428E config cluster manage timer 50 cluster member Description The cluster member command is used to add member switch To delete the corresponding member please use no cluster member command The add delete operations of member switches should be implemented by the commander switch according to the MAC address 245 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Syntax cluster member mac address mac address no cluster member mac address mac address Parameter mac address The MAC address of the member switch desired to join in or to be deleted from the cluster Command Mode Global Configuration Mode Example Add the switch whose MAC address is 0e 3f 4g 5e 6d 7b to the cluster TL SL5428E config cluster member mac address 0e 3f 4g 5e 6d 7b cluster candidate Description The cluster candidate command is used to specify the current switch as candidate switch Syntax cluster candidate Command Mode Global Configuration Mode Example Specify the current switch as candidate switch TL SL5428E config cluster candidate cluster indivi
214. to the process of forwarding copies of packets from one port to a monitoring port Usually the monitoring port is connected to data diagnose device which is used to analyze the monitored packets for monitoring and troubleshooting the network monitor session destination interface Description The monitor session destination interface command is used to configure the monitoring port Each monitor session has only one monitoring port To change the monitoring port please use the monitor session destination interface command by changing the port value To delete the corresponding monitor session configuration please use no monitor session command Syntax monitor session session_num destination interface fastEthernet port gigabitEthernet port no monitor session session_num Parameter session_num The monitor session number the value of which is 1 port The Fast Gigabit Ethernet port number Command Mode Global Configuration Mode Example Create monitor session 1 and configure Fast Ethernet port 1 as the monitoring port TL SL5428E config monitor session 1 destination interface fastEthernet 1 0 1 Delete the monitor session 1 TL SL5428E config no monitor session 1 156 TL SL5428E MOSUCEU MIA EME Eli e BRETT monitor session source interface Description The monitor session source interface command is used to configure the monitored port To delete the corresponding monitored port please use no
215. ts will be discarded To restore to the default configuration please use no ip dhcp snooping limit rate command Syntax ip dhcp snooping limit rate va ue no ip dhcp snooping limit rate Parameter value The value of Flow Control The options are 0 5 10 15 20 25 30 packet second The default value is 0 which stands for disable 73 TL SL5428E BAG 6 0 5 1 aE TATT DL EG e M EE ETT IT Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Set the Flow Control of Fast Ethernet port 2 as 20 pps TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if ip dhcp snooping limit rate 20 ip dhcp snooping decline Description The ip dhcp snooping decline command is used to enable the Decline Protect feature To disable the Decline Protect feature please use no ip dhcp snooping decline command Syntax ip dhcp snooping decline no ip dhcp snooping decline Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the Decline Protect feature of Fast Ethernet port 2 TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if ip dhcp snooping decline show ip source binding Description The show ip source binding command is used to display the IP M
216. ttack type Syntax ip dos prevent detect detect time Parameter detect time Specify the detect time for each DoS attack type except the flooding attack type ranging from 1 to 5 in second Command Mode Global Configuration Mode Example Detect the DoS attack and specify the detect time for each DoS attack type except the flooding attack type as 5 seconds TL SL5428E config ip dos prevent detect 5 clear ip dos prevent detect statistics Description The clear ip dos prevent detect statistics command is used to clear the information statistic of the detected DoS attack Syntax clear ip dos prevent detect statistics Command Mode Privileged EXEC Mode and Any Configuration Mode Example Clear the information statistic of the detected DoS attack TL SL5428E config clear ip dos prevent detect statistics 87 TL SL5428E MOSCA ET Xe DL Eli e M EE ETT IT show ip dos prevent Description The show ip dos prevent command is used to display the DoS information of the detected DoS attack including enable disable status the DoS Defend Type the count of the attack etc Syntax show ip dos prevent Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the DoS information of the detected DoS attack globally TL SL5428E config show ip dos prevent 88 TL SL5428E MOSCA EME EG e M EE ETT IT Chapter 16 IEEE 802 1X Commands IEEE 802 1X function is to provide an access control for LA
217. ty Example Map CoS 5 to TC 2 TL SL5428E config qos queue cos map 5 2 qos queue dscp map Description The qos queue dscp map command is used to configure the mapping relation between DSCP Priority and the TC egress queue To return to the default configuration please use no qos queue dscp map command DSCP DiffServ Code Point is a new definition to IP ToS field given by IEEE This field is used to 151 TL SL5428E EN LLE A EME Eli e M EE ETT IT divide IP datagram into 64 priorities When DSCP Priority is enabled IP datagram are mapped to different priority levels based on DSCP priority mode non IP datagram with IEEE 802 1Q tag are mapped to different priority levels based on IEEE 802 1P priority mode if IEEE 802 1P Priority is enabled the untagged non IP datagram are mapped based on port priority mode Syntax qos queue dscp map dscp list tc id no qos queue dscp map Parameter dscp list List of DSCP value One or several DSCP values can be typed using comma to separate Use a hyphen to designate a range of values for instance 1 4 7 11 indicates choosing 1 4 5 6 7 11 The DSCP value ranges from 0 to 63 tc id The egress queue the packets with tag are mapped to It ranges from 0 to 3 which represents TCO TC1 TC2 TC3 respectively Command Mode Global Configuration Mode User Guidelines 1 By default the mapping relation between tag and the egress queue is 0 15 TCO 16 31 TC1 32 47 TC2
218. uerier of all VLANs TL SL5428E config show ip igmp snooping querier 213 TL SL5428E MOSCA EME EG e M EE ETT IT Chapter 30 SNMP Commands SNMP Simple Network Management Protocol functions are used to manage the network devices for a smooth communication which can facilitate the network administrators to monitor the network nodes and implement the proper operation snmp server Description The snmp server command is used to enable the SNMP function By default it is disabled To return to the default configuration please use no snmp server command Syntax snmp server no snmp server Command Mode Global Configuration Mode Example Enable the SNMP function TL SL5428E config snmp server snmp server view Description The snmp server view command is used to add View To delete the corresponding View please use no snmp server view command The OID Object Identifier of the SNMP packets is used to describe the managed objects of the switch and the MIB Management Information Base is the set of the OIDs The SNMP View is created for the SNMP management station to manage MIB objects Syntax snmp server view name mib oid include exclude no snmp server view name mib oid 214 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Parameter name The entry name of View ranging from 1 to 16 characters Each View can include several entries with the same name mib oid MIB Object ID It is the
219. uration Mode and configure Gigabit Ethernet port 25 TL SL5428E config interface gigabitEthernet 1 0 25 interface range gigabitEthernet Description The interface range gigabitEthernet command is used to enter the interface range gigabitEthernet Configuration Mode and configure multiple Gigabit Ethernet ports at the same time Syntax interface range gigabitEthernet port list 137 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT Parameter port list The list of Gigabit Ethernet ports Command Mode Global Configuration Mode User Guidelines Command in the Interface Range gigabitEthernet Mode is executed independently on all ports in the range It does not affect the execution on the other ports at all if the command results in an error on one port Example To enter the Interface Range gigabitEthernet Configuration Mode and configure Gigabit Ethernet ports 25 26 and 28 at the same time by adding them to one port list TL SL5428E config interface range gigabitEthernet 1 0 25 26 1 0 28 description Description The description command is used to add a description to the Ethernet port To clear the description of the corresponding port please use no description command Syntax description string no description Parameter string Content of a port description ranging from 1 to 16 characters Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet int
220. used for configuring the LLDP functions Chapter 32 Cluster Commands Provide information about the commands used for configuring the Cluster Management function TL SL5428E JetStream L2 Managed Switch CLI Guide L2 Managed Switch CLI Guide Chapter 1 Using the CLI 1 1 Accessing the CLI You can log on to the switch and access the CLI by the following two methods 1 Log on to the switch by the console port on the switch 2 Logon to the switch remotely by a Telnet or SSH connection through an Ethernet port 1 1 1 Logon by a console port To log on to the switch by the console port on the switch please take the following steps 1 Connect the PCs or Terminals to the console port on the switch by a provided cable 2 Click Start All Programs gt Accessories gt Communications Hyper Terminal to open the Hyper Terminal as the Figure 1 1 shown Set Program Access and Defaults W Windows Catalog Windows Update Program Updates 3 Accessibilty ICH Games Or ei Startup em Entertainment Internet Explorer H System Tools e msn 9 Address Book Network Connections 2 Network Setup Wizard E New Connection Wizard Ei Internet Internet Explorer ES E mail Microsoft Office Out ES Outlook Express 5 Calculator F Remote Desktop Connection y Remote Assistance E Command Prompt lt 2 Wireless Network Setup Wizard e Notepad Windows Media Player DB Notepad
221. ver enginelD command is used to display the enginelD of the SNMP Syntax show snmp server enginelD Command Mode Privileged EXEC Mode and Any Configuration Mode 230 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Example Display the enginelD TL SL5428E show snmp server enginelD show rmon history Description The show rmon history command is used to display the configuration of the history sample entry Syntax show rmon history index Parameter index The index number of the entry selected to display the configuration ranging from 1 to 12 in the format of 1 3 5 You can select more than one entry for each command By default the configuration of all history sample entries is displayed Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configuration of all history sample entries TL SL5428E show rmon history show rmon event Description The show rmon event command is used to display the configuration of SNMP RMON Event Syntax show rmon event index Parameter index The index number of the entry selected to display the configuration ranging from 1 to 12 in the format of 1 3 5 You can select more than one entry for each command By default the configuration of all SNMP RMON enabled entries is displayed 231 TL SL5428E BA 6 KY LL a EME EG e m EE TT IT Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display
222. wer value has the higher priority It ranges from o to 2000000 By default it is O which is mean auto int cost Internal Path Cost which is used to choose the path and calculate the path costs of ports in an MST region It is an important criterion on determining the root port The lower value has the higher priority By default it is automatic It ranges from o to 2000000 By default it is O which is mean auto portfast Enable Disable Edge Port By default it is disabled The edge port can transit its state from blocking to forwarding rapidly without waiting for forward delay point to point The P2P link status with auto open and close options By default the option is auto If the two ports in the P2P link are root port or 183 TL SL5428E BA 6 LLE a EME Eli e m EE ETT IT designated port they can transit their states to forwarding rapidly to reduce the unnecessary forward delay Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the STP function of Fast Ethernet port 1 and configure the Port Priority as 64 ExtPath Cost as 100 IntPath Cost as 100 and then enable Edge Port TL SL5428E config interface fastEthernet 1 0 1 TL SL5428E config if spanning tree common config port priority 64 ext cost 100 int cost 100 portfast enable point to point open spanning tree mode
223. x speed 10 100 1000 auto no speed Parameter 10 100 1000 auto The speed mode of the Ethernet port There are four options 10Mbps 100Mbps 1000Mbps and Auto negotiation mode default Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Configure the Speed Mode as 100Mbps for Gigabit Ethernet port 25 TL SL5428E config interface gigabitEthernet 1 0 25 TL SL5428E config if speed 100 storm control broadcast Description The storm control broadcast command is used to enable the broadcast control function To disable the broadcast control function please use no storm control broadcast command Broadcast control function allows the switch to filter broadcast in the network If the transmission rate of the broadcast packets exceeds the set bandwidth the packets will be automatically discarded to avoid network broadcast storm Syntax storm control broadcast rate rate no storm control broadcast 141 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Parameter rate Specify the bandwidth for receiving broadcast packets on the port The packet traffic exceeding the bandwidth will be discarded By default the value is 128K Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface rang
224. x reauth req 5 dot1x Description The dot1x command is used to enable the IEEE 802 1X function for a specified port To disable the IEEE 802 1X function for a specified port please use no dot1x command 92 TL SLSA7pERIGCEIORRKR EIET DL Eli e M EE ETT IT Syntax dot1x no dot1x Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the IEEE 802 1X function for the Fast Ethernet port 1 TL SL5428E config interface fastEthernet 1 0 1 TL SL5428E config if dot1x dot1x guest vlan interface Description The dot1x guest vlan command is used to enable the guest VLAN function for a specified port To disable the Guest VLAN function for a specified port please use no dot1x guest vlan command Please ensure that the Control Type of the corresponding port is port based before enabling the guest VLAN function for it Syntax dot1x guest vlan no dot1x guest vlan Command Mode Interface Configuration Mode interface fastEthernet interface range fastEthernet interface gigabitEthernet interface range gigabitEthernet Example Enable the Guest VLAN function for Fast Ethernet port 2 TL SL5428E config interface fastEthernet 1 0 2 TL SL5428E config if dot1x guest vlan 93 TL SL5428E MOCSUCEU MIA EME EG e M EE ETT IT dot1x port control Description The dot1x port control command i
225. ydney Brisbane UTC 11 00 TimeZone for Solomon Is New Caledonia Vladivostok UTC 12 00 TimeZone for Fiji Magadan Auckland Welington UTC 13 00 TimeZone for Nuku alofa Samoa ntp server The IP Address for the Primary NTP Server 120 TL SLSA7pERIGCEIORRKR EIET DL Eli e BRETT backup ntp server The IP Address for the Secondary NTP Server fetching rate Specify the rate fetching time from NTP server Command Mode Global Configuration Mode Example Configure the system time mode as NTP the time zone is UTC 12 00 the primary NTP server is 133 100 9 2 and the secondary NTP server is 139 78 100 163 the fetching rate is 11 hours TL SL5428E config system time ntp UTC 12 00 133 100 9 2 139 79 100 163 11 system time dst predefined Description The system time dst predefined command is used to select a predefined DST configuration and the configuration can be recycled Syntax system time dst predefined USA Australia European New Zealand Parameter USA Australia European New Zealand Predefined DST mode with four options USA Australia European and New Zealand By default the setting is European The DST time periods which the four predefined DST mode represents are displayed as follow USA Second Sunday in March 02 00 First Sunday in November 02 00 Australia First Sunday in October 02 00 First Sunday in April 03 00 European Last Sunday i

TP-Link TL-SL5428E V2 CLI Reference Guide

Contents

Download Pdf Manuals

Related Search

Related Contents