TP-Link TL-SF1008P V4 Installation Guide
Contents
1. LAN access points network cameras network hubs embedded computers etc 1 2 Convention The switch or TL SF1008P mentioned in this Installation Guide stands for TL SF1008P 8 Port 10 100Mbps Desktop Switch with 4 Port PoE without any explanation 1 3 Features gt VV V WV Complies with IEEE802 3 IEEE802 3u IEEE802 3x IEEE802 3af standards 8 10 100Mbps Auto Negotiation RJ45 ports with 4 ports supporting PoE function port 1 port 4 all of them support Auto MDI MDIX Supports PoE power up to 15 4W for each PoE port Supports PoE power up to 57W for PoE ports Supports PoE IEEE802 3af compliant PDs Supports IEEE802 3x flow control for Full duplex Mode and backpressure for Half duplex Mode 2K entry MAC address table of the TL SF1008P with auto learning and auto aging LED indicators for monitoring Power Link Act and PoE Status External power adapter supply Chapter 2 Installation During the installation procedure please only use the accessories equipped with the switch 2 1 Mounting the Switch on a Desk To install the switch please follow the steps 1 Place the switch on a flat desk 2 Remove the adhesive backing papers from the rubber cushions 3 Turnover the switch and attach the supplied four rubber cushions to the recessed areas on the bottom at each corner of the switch A Note 1 Please avoid any heavy thing placed on the switch 2 Make sure the power is off before unplugging the power ada2. Store and Forward MAC ACESS Automatically learning automatically aging Learning Frame Filter 10Base T 14880pps Port Rate 100Base Tx 148800pps Port Frame 10Base T 14880pps Port Forward Rate 100Base Tx 148800pps Port Environmental and Physical 2 3 Watts max no PD connected Power Consumption 59 3 watts max with 57W PD connected Operating Temperature 0 40 C 32 104F Storage Temperature 40 70 C 40 158 F Operating Humidity 10 90 non condensing Storage Humidity 5 90 non condensing
3. TP LINK Installation Guide TL SF1008P 8 Port 10 100Mbps Desktop Switch with 4 Port PoE EAL REV4 0 0 7106504530 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TP LINK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2013 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT FE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with part 15 of the FCC Rules Operation is subject to the followi
4. ch is identified the switch will supply power through the PoE port and then you can use it as a 10 100Mbps Auto Negotiation RJ45 Ethernet port The working status can be indicated by the corresponding LEDs on the front panel 7 gt Ethernet Ports 1 8 Besides the 4 PoE ports the TL SF1008P switch is also equipped with the other four 10 100Mbps Auto Negotiation RJ45 ports without PoE function Once the network devices are connected to these 8 ports through the network cable the switch will make them plug and play according to the Auto MDI MDIX detection The working status can be indicated by the corresponding LEDs on the front panel A Note Make sure the PDs you connected to the switch are complaint with IEEE 802 3af Appendix A Specifications General Standard IEEE802 3 IEEE802 3u IEEE802 3x IEEE802 3af Protocol CSMA CD Data Transfer Rate Ethernet 10Mbps Half Duplex 20Mbps Full Duplex Fast Ethernet 100Mbps Half Duplex 200Mbps Full Duplex 10Base T UTP category 3 4 5 cable maximum 100m Network EIA TIA 568 100Q STP maximum 100m Media Cable 100Base TX UTP category 5 5e cable maximum 100m EIA TIA 568 1000 STP maximum 100m Number of 8 10 100Mbps Auto Negotiation RJ45 ports with Ports PoE enabled port 1 port 4 PoE Power on RJ45 Powert pin 3 amp pin 6 Power pin 1 amp pin 2 LEDs Power Link Act PoE Status PoE MAX anster
5. ere is no PD connected to the corresponding port A A valid link is established on the port Link Act HOES port 1 Flashing Data transmitting or receiving on port 8 green corresponding port Off No device is connected to the corresponding port A Note If all POE PDs power consumption is gt 57W a priority will be arranged among the PoE ports like port 1 port 2 port 3 gt 6 port 4 then the system will cut off the power of the lowest priority port Priority This function will help protect the system when the system power is overloaded For example Port 1 2 and 4 is using 15 4W maximum power for per port is 15 4W the system power is 46 2W in total If there is an additional PD inserted to Port 3 with 12W and then the system will cut off the power of Port 4 because of the overloaded power this means Port 1 2 will use 15 4W and Port3 will use 12W no power will be supplied to Port 4 3 2 Rear Panel is saVet ie ES ee ee 2 EEr E ea E a E Figure 3 2 TL SF1008P Switch Rear Panel The following parts are located on the rear panel gt Power 48V 48V indicates the input voltage of the power adapter provided with this TL SF1008P switch The Power socket is where you will connect the power adapter gt PoE Ports 1 4 These ports support PoE function which integrates power and data onto one Ethernet cable Once the device you connect to the swit
6. es Appendix A Specifications 0cscscseeeeeseeeeeeeeeeeeeeeeeaeee Package Contents The following items should be found in your box gt One TL SF1008P 8 Port 10 100Mbps Desktop Switch with 4 Port PoE gt One DC Power Adapter gt Four rubber cushions to be used under the switch gt This Installation Guide A Note Make sure that the box contains the above items If any of the listed items are damaged or missing please contact your distributor Chapter 1 Introduction of the Product Thank you for choosing the TL SF1008P 8 Port 10 100Mbps Desktop Switch with 4 Port PoE 1 1 Overview of the Product The TL SF1008P 8 Port 10 100Mbps Desktop Switch with 4 Port PoE provides the seamless network connection which integrates 100Mbps Fast Ethernet and 10Mbps_ Ethernet network capabilities This PoE switch is also a Power Sourcing Equipment PSE Four of the eight Auto Negotiation RJ45 ports port 1 port 4 on the switch support Power over Ethernet PoE function which can automatically detect and supply power with those IEEE 802 3af complaint powered devices PDs PSE A device switch or hub for instance that will provide power in a PoE setup PoE This technology describes a system to transmit electrical power along with data to remote devices over standard twisted pair cable in an Ethernet network PD A device powered by a PSE and thus consumes energy Examples include powering IP telephones wireless
7. ng two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment CE Mark Warning CE This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures SAFETY NOTICES AN Cautions Do not use this product near water for example in a wet basement or near a swimming pool Avoid using this product during an electrical storm There may be a remote risk of electric shock from lightning CONTENT Package Contents c cceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaeaeeeeeeenens Chapter 1 Introduction of the Product sceeseseeeeeeeeees 1 1 Overview of the Product c cceseeeeseenetneeeees 1 2 CONVENTION ccsecescceeeeteseeeeseeeseeeeeseeeseeeeseenseeneees 1 3 Feature ccccssccsseeseeseneeeseeesseeeseesseeseneesseessseeesees Chapter 2 Installation cccccceeeeeeeeeeeeeeeaeeeeeeeeeeeeeeeeeeeee 2 1 Mounting the Switch on a DeSK 2 2 Power OMi eee Chapter 3 Identifying External Components sceeseses 3 1 Front Panel ccccccccseeesseesseseseesnesseeeeseeseeeeeseeneeee 3 2 Rear Panel c ccccccsesesssesseesseeesesseessseeseneesseensee
8. pter 2 2 Power On The TL SF1008P switch can be used with DC power supply Powering on the switch it will automatically initialize and its LED indicators will respond as follows 1 Firstly the Power LED indicator will light up 2 Then the Link Act LED indicators will flash momentarily for one second which represents a resetting of the system A Note If the LED indicators don t respond as described above please check the power supply and its connection Chapter 3 Identifying External Components This Chapter describes the front panel rear panel and LED indi cators of the switch 3 1 Front Panel Figure 3 1 TL SF1008P Switch Front Panel The switch s LEDs are located on the front panel Name _ Status Indication Power ae The switch is powered on Off The switch is powered off On There is a PoE PD connected to the port PEE green which supplies power successfully o z ports Flashing The PoE power circuit may be in short or port 1 green the power current may be overloaded port 4 No PD is connected to the corresponding Off port or no power is supplied according to the power limits of the port On The power of all the connected PoE ports is d gt 50W No power may be supplied if red additional PDs are connected PoE Flashing The power of all the connected PoE ports is MAX red gt 57W The power of all the connected PoE ports is Off lt 50W or th
Download Pdf Manuals
Related Search