Theta Digital Intrepid User's Manual
Contents
1. WARNING United States law prohibits disposition of these commodities to Libya Laos North Korea Cambodia or Cuba unless otherwise authorized by the United States O 2000 Theta Digital Corporation All rights reserved Written and Illustrated by Glenn Buckley This manual is also available for download as a PDF file at Theta Digital s website http www thetadigital com No part of this publication may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of Theta Digital Corporation CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of significant magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHOCK DO NOT USE THE AC POLARIZED PLUG WI2. JU9UND H paje nbay OK UO joued jnduj JUOJ4 AINI JO JUOQ rin p pu3 l6uis JO pa3uejeg 96ejS indino 965819 J9AUC 96ejs indu weibeig 19019 pid nul Front Panel Layout AR THETA Intrepid ZERO FEEDBACK HIGH CURRENT AMPLIFIER THERMAL e STANDBY q Figure 2 Front Panel Layout 1 STANDBY button After the rear panel MAIN POWER switch is turned on press the front panel STANDBY button to exit the standby mode All channels will come out of standby 2 STANDBY LED Illuminates red when the power amplifier is in STANDBY green when the amplifier is active 3 THERMAL LED Illuminates when any channel s temperature rises above the maximum operating temperature and puts the Intrepid into standby Rear Panel Layout pam N ourPur ourPur ourPUr oureur SINGLE ENDED SINGLE ENDED SINGLE ENDED SINGLE ENDED INPUT INPUT INPUT INPUT satanceo Y j ataco jJ saance BALANCED CHANNEL 4 CHANNEL 3 CHANNEL 2 CHANNEL 1 CAUTION ALL OUTPUTS ARE BRIDGED DO NOT GROUND NEGATIVE OUTPUTS A C LINE Figure 3 Rear Panel Layout showing the optional RS 232 Jacks installed BINDING POST Connect plus and minus speaker wires for one speaker to appropriatelv marked terminals of each post The binding posts can accept spade lugs banana plugs or bare wire SINGLE ENDED input jack BALANCED input jack AC POWER INPUT Rear panel FUSE I
3. that is intended for use DOES NOT DEFEAT THE AC GROUND on its AC outlets Only the highest powered line conditioners should be considered for use with the Intrepid Otherwise the amplifier s power output may be compromised DO NOT remove any cover panels from the Intrepid as there are no user serviceable components inside Refer servicing and updating to qualified service personnel only Endcaps NOT shorting plugs on all unused RCA inputs will improve the sound quality and may reduce the susceptibility to RF induced anomalies It is imperative that the Intrepid be operated in a well ventilated environment and the immediate external temperature be maintained as specified in Appendix D of this manual External cooling fans may be required in some cases Do not stack any equipment directly above or below the Intrepid as to protect it from overheating as well as the continued functionality of any equipment near and around it Each channel is a balanced bridge amplifier thus the negative speaker terminal is NOT a ground and cannot be connected to a ground or a loudspeaker system with a common ground Consult your speaker manufacturer to ensure that any speaker in your system that will be connected to the Intrepid does NOT have internal circuitry with a common ground lnpouu jndjno auo Buimoys pidojjuj wesbeig 490 19 L 9IN I4 abels mdmo 9beJS JAALQ Cs punoje paouejeg papu3 a Buls JO pasuejeg Ajddns Ajddns JOMOq JOMOq
4. AROUND IT EACH CHANNEL IS A BALANCED BRIDGE AMPLIFIER THUS THE NEGATIVE SPEAKER TERMINAL IS NOT A GROUND AND CANNOT BE CONNECTED TO A SYSTEM GROUND OR LOUDSPEAKER SYSTEM WITH A COMMON GROUND CONSULT YOUR SPEAKER MANUFACTURER TO ENSURE THAT ANY SPEAKER IN YOUR SYSTEM THAT WILL BE CONNECTED TO THE INTREPID DOES NOT HAVE INTERNAL CIRCUITRY WITH A COMMON GROUND AFTER MARKET and THIRD PARTY MODIFICATIONS Please note that any after market and or third party modifications will void the warranty In the case of changing the feet on a unit in order to prevent any damage which will also not be covered under warranty please verify that the screws being used to secure non Theta feet do not screw any deeper into the chassis than the original ones The original screw is 1 4 20 by 1 2 and goes into the chassis 1 4 inch iv Table of Contents INTRODUCTION Getting to know your Intrepid This Intrepid has been put through a rigorous and unique testing procedure that ensures that it will last for many years with minimal service requirements This procedure includes the following e All assembled circuit boards are given a thorough visual inspection and are then tested in a bench reference Intrepid e The tested assembled circuit boards are then installed in a new Intrepid and the whole unit is tested for every function and parameter e The unit is put on a burn in torture rack to test for any possible component failures e It is then teste
5. D Intrepid sends on this pin Figure 5 Intrepid RS232 Jack Pinout 11 ZHIN882 L NODVHAV REQ 9600 JA E EN o o o o 5858 L ED U Eso u u u Etm A A 09 A Figure 6 Intrepid RS232 Jumper Settings RS232 Jumper Settings There are 2 possible Baud rates 9600 and 19200 The factory default is 19200 To change the baud rate to 9600 move the jumper to the center and top pins if the RS232 board is orientated as in figure 6 The STATUS can be returned to the controller either automatically every time a parameter has changed or the user can request it manually The factory default is AUTO To set the Echo STATUS to return Status information only upon request move the AUTO REQ jumper to the top pins or nearer to REQ on the RS232 board The three SELECT jumpers are not currently implemented 12 Appendix D Specifications Inputs Analog audio 1 Single ended per channel RCA 1 Balanced per channel XLR Input Impedance 50 KQ Single Ended or Balanced for each phase Input sensitivity Single Ended 1 5V RMS input for 100W into 8 ohms Balanced 0 75V RMS input for 100W into 8 ohms Gain Single Ended 25 5dB 19x Balanced 31 5dB 38x Polarity Single Ended Non Inverting Balanced Pin 2 Positive Pin 3 Negative for Non Inverting Output Outputs Analog Audio 1 balanced output per channel YO RS232 1
6. DB9 and 1 RJ45 connector Modes Processes Standby All channels are muted and output bias is reduced to 40 Thermal One or more channels has overheated amp automaticallv switches to Standbv Power Output 8 ohms one channel driven 100 W rated 130 W tvpical Frequency Response THD Noise Signal to Noise Ratio Power Requirements Power Consumption Standby Trigger Input Dimensions Weight Maximum Operating Temperature 8 ohms five channels driven 100 W rated 4 ohms one channel driven 200 W rated 3dB points full power 0 9 Hz 350 KHz lt 2 unweighted gt 100dB 117 VAC 7 7 amp 230 VAC 4 amp 50 60 Hz for full power in all channels 80W Standby 100W idle 900W full power 5 12 VDC Pulse between 1 and 500mS 17 5 8 W x 6 1 4 H x 20 1 2 D 448 x 159 x 521 mm 115 W typical 210 W typical 58 Lbs Stand alone 26 3 Kg 64 Lbs Boxed with accessories 29 Kg Internal 176 F 80 C Room 131 F 55 C 13 90 DAY LIMITED WARRANTY TERMS AND CONDITIONS 3 Year optional extended service contract 1 Theta Digital Corporation henceforth referred to as Theta warrants the product designated herein to be free of manufacturing defects in material and workmanship subject to the conditions set forth herein for a period of 90 days from the date of purchase by the original purchaser henceforth referred to as purchaser If the purchaser registers the unit with Theta by mailing
7. If the Intrepid should function abnormally during operation please review the items in the following checklist Please be sure to thoroughly check all other connected components such as speakers preamplifiers as well as cables Symptom Possible Cause s No power or front panel Power cable is not inserted 100 into AC Ensure that the AC cord is inserted all the lights and no sound input connector way into the Intrepid and that the wall outlet is active Rear panel fuse is open Replace with same type and rating ONLY Circuit breaker is open AC outlet Check the AC outlet circuit breaker and reset if necessary or contact your dealer No audio output Overheating If the front panel THERMAL LED is illuminated shut down the Intrepid until it cools An external fan mav be necessarv Hot Warm Normal operation Appendix B Wiring Diagram This section provides an example illustration of an input and output wiring scheme Before making any connections please turn off ALL audio and video devices Unplug those that do not have a main power switch It is recommended that all cables including speaker cables be kept as short as possible for best sound quality To Front To Front To To Right To Left Right Left Center Surround Surround To From Speaker Speaker Speaker Speaker Speaker Controller CAUTION ALL Q fPUTS ARE BRIDGED DO NOL MOUND NEGATIVE OUTPUTS A C LINE From From From From Right From Left To Front RT Fro
8. OR ANY PURPOSE BEFORE MAKING ANY CONNECTIONS TO THE INTREPID FIRST TURN OFF THE POWER AND THEN DISCONNECT THE AC POWER CORD WHEN INSTALLING THE INTREPID IN YOUR SYSTEM MAKE CERTAIN TO ALLOW A MINIMUM OF Y INCH OF VENTILATION ON EACH SIDE OF THE UNIT ALSO ALLOW AT LEAST 3 INCHES OF VENTILATION SPACE ABOVE THE UNIT IMPROPER VENTILATION OF THE UNIT MAY CAUSE OVERHEATING WHICH MAY DAMAGE THE UNIT AND CAUSE A FIRE PLACE THE UNIT ON A SOLID SURFACE ONLY I E NOT ON CARPET ETC DO NOT PLACE THE INTREPID NEAR HEAT SOURCES SUCH AS DIRECT SUNLIGHT STOVES HEAT REGISTERS RADIATORS OR OTHER HEAT PRODUCING EQUIPMENT TO PREVENT DAMAGE TO THE ANALOG OUTPUT CIRCUITRY BE CERTAIN NOT TO SHORT THE OUTPUT SIGNAL TO GROUND ENSURE THAT YOUR AUDIO OUTPUT CABLES DO NOT HAVE ANY INTERNAL SHORTS BEFORE CONNECTING THEM TO THE INTREPID IF REPLACEMENT OF THE AC LINE FUSE AND OR ANY INTERNAL FUSE BECOMES NECESSARY REPLACE ONLY WITH SAME VALUE AND TYPE OF FUSE NEVER BYPASS THE FUSE IF THE AC CORD BECOMES DAMAGED DO NOT USE IT IMMEDIATELY REPLACE IT WITH A NEW ONE OF THE SAME OR BETTER RATING IT IS IMPERATIVE THAT THE INTREPID BE OPERATED IN A WELL VENTILATED ENVIRONMENT AND THE IMMEDIATE EXTERNAL TEMPERATURE BE MAINTAINED AS SPECIFIED EXTERNAL COOLING FANS MAY BE REQUIRED IN SOME CASES DO NOT STACK ANY EQUIPMENT DIRECTLY ABOVE OR BELOW THE INTREPID AS TO PROTECT IT FROM OVERHEATING AS WELL AS THE CONTINUED FUNCTIONALITY OF ANY EQUIPMENT NEAR AND
9. TH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE Extension cords are not recommended for use with this product Intrepid Identification Record This information is for your records and for future identification of the Intrepid Please take a moment to fill out all pertinent data now and as upgrades and or options are installed Whenever upgrades inquiries and or changes are requested the serial number will be required SERIAL NUMBER DATE PURCHASED DEALER S NAME DEALER S ADDRESSIPHONE INSTALLED CARDS OPTIONS Date of installation TT Date of installation Date of installation 111 SAFETY PRECAUTIONS Please carefully read each item of the operating instructions and safety precautions before installing and using this product Use extra care to follow the warnings written on the product itself and or in the operating instructions Keep the operating instructions and safety precautions for future reference CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE ANY OF THE COVER PANELS NO USER SERVICEABLE PARTS INSIDE REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY TO PREVENT FIRE OR SHOCK HAZARD DO NOT ALLOW LIQUIDS TO SPILL OR OBJECTS TO FALL INTO ANY OPENINGS OF THE PRODUCT THIS UNIT IS SUPPLIED WITH A 3 PIN GROUNDED AC PLUG ALWAYS INSERT THE AC PLUG INTO A GROUNDED OUTLET DO NOT REMOVE THE GROUND PIN OR DISABLE THE GROUND F
10. THETA DIGITAL PREFACE CONGRATULATIONS You have just acquired one of the most advanced and versatile components for the amplification of audio ever to have been developed IMPORTANT Save all packaging in a dry place away from fire hazards Your Intrepid is a precision electronic instrument and should be properly packaged any time shipment is made In the unlikelv event that you have to return your Intrepid to the factory for service or updating the original packaging will best protect the unit from shipping damage In order to achieve the fullest flexibility and enjoyment from your Intrepid we at Theta recommend that you read this manual in full before connecting the unit to your audio video system Note lt is imperative that the Intrepid be operated in a well ventilated environment and that the immediate external temperature be maintained as specified External cooling fans may be required in some cases Do not stack any equipment directly above or below the Intrepid to protect it from overheating as well as to protect the continued functionality of equipment near and around it Warning Each channel is a balanced bridge amplifier thus the negative speaker terminal is NOT a ground and cannot be connected to a system ground or a loudspeaker system with a common ground Consult your speaker manufacturer to ensure that any speaker in your system that will be connected to the Intrepid does NOT have internal circuitry with a common ground
11. cannot be connected to a ground or a loudspeaker system with a common ground Consult your speaker manufacturer to ensure that any speaker in your system that will be connected to the Intrepid does NOT have internal circuitry with a common ground Connect a 12V pulse trigger source to the trigger input of the Intrepid if it is desired to be taken in and out of standby via another device If the Intrepid s functionality is to be controlled from a remote controller via RS232 connect the RS232 cable between the Intrepid and the controller When first turning on the rear panel power switch the red STANDBY LED on the front panel will illuminate indicating that all channels are in standby mode When in standby the signal is muted and the output bias of each channel is reduced to approximately 40 percent Remote Trigger When the rear panel STANDBY TRIGGER jack receives a 5 12 VDC pulse the Intrepid will change its state from either standby to operate or operate to standby depending on what the current state is RS232 RS232 is an option in the Intrepid It can be installed at any time either at the factory or by an authorized Theta dealer All functions of the Intrepid can be controlled and monitored via RS232 using either the RJ45 or DB9 connector As long as the rear panel power switch in turned on the RS232 circuitry is always active thus allowing the Intrepid to be taken out of STANDBY via RS232 Appendix A Troubleshooting Guide
12. d on an audio analyzer for all pertinent parameters e The unit has all remaining chassis components installed and then undergoes a complete visual inspection which assures that all Intrepids meet visual specifications e The Intrepid then undergoes a critical listening and functional test Burn in Time This unit has a break in period of about 1 week during which continuous improvement in sound quality will be observed It is recommended that music be played continuously through the unit during this time to expedite the break in period Reference Manual Conventions For clarity purposes references to buttons and LED s will be shown in bold capital letters IMPORTANT NOTICE VI VII It is imperative that the Intrepid be connected to a ground via its three wire AC power cord It is important that the AC power outlet which the Intrepid is plugged into is actually grounded Failure to do so will severely compromise the performance reliability and safety of use of the Intrepid Ventilation is an important issue when placing the Intrepid in a system Make certain that the Intrepid is placed in a well ventilated area or rack unit Heat must be dissipated and cool air must be allowed to enter the Intrepid Please take note that some powerline conditioners defeat the AC power ground on their outlets If the intention is to plug the Intrepid into a line conditioner check with your dealer to make certain that the particular conditioner
13. f necessary replace with same type and rating only Main Power Switch Master power switch Disconnects AC to all circuits It is recommended that this be left ON at all times during regular use with the exception of whenever cables are connected disconnected or when the unit is not going to be used for an extended period of time STANDBY REMOTE TRIGGER jack When the rear panel STANDBY TRIGGER jack receives a 5 12 VDC pulse the Intrepid will change its mode from either standby to operate or operate to standby depending on its current mode DB9 RS232 connector Used for connecting an external controller to the Intrepid to control and monitor its functions RJ45 RS232 connector See DB9 RS232 connector OPERATION Before turning on the Intrepid ensure that all precautions and warnings have been carefully reviewed and adhered to Damage to the Intrepid caused by improper operation wiring and or ventilation will not be covered under warranty and Theta will not be liable for any consequential damage or loss Connecting the Intrepid With the Intrepids rear panel main power switch turned off connect the signal outputs of each preamp processor channel to either the single ended or balanced input of the Intrepid Connect each channel output to the input of the speaker that is intended to be driven Please refer to figure 4 Please Note Each channel is a balanced bridge amplifier thus the negative speaker terminal is NOT a ground and
14. in the warranty card together with a copy of the bill of sale within 14 days of the date of purchase said purchaser will be registered for an extended service contract The extended service contract extends the 90 days to a period of 3 years from the date of purchase by the original purchaser or no later than 7 years from the date of shipment to the authorized Theta dealer whichever comes first 2 CONDITIONS This warranty is subject to the following conditions and limitations The warranty is void and inapplicable if the product has been used or handled other than in accordance with the instructions in the owner s manual abused or misused damaged by accident or neglect or in being transported or if the defect is due to the product being repaired or tampered with or modified by anyone other than Theta or an authorized Theta repair center In the unlikely event that the unit requires service contact Theta for an RA Return Authorization number The product must be packed and returned to Theta or an authorized Theta repair center by the customer at his or her sole expense Theta will pay return freight of its choice A returned product must be accompanied by a written description of the defect a photocopy of the original purchase receipt and a daytime phone number where the owner can be reached The unaltered receipt must clearly list model and serial number the date of purchase the name and address of the purchaser and authorized dealer and the pu
15. ion of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state 7 WARRANTOR Inquiries regarding the above limited warranty may be sent to the following address THETA DIGITAL CORPORATION 5330 DERRY AVENUE SUITE R AGOURA HILLS CA 91301 WARRANTY OUTSIDE THE USA Theta has formal distribution in many of the countries of the free world in each country the Theta Importer has contractually accepted the responsibility for product warranty Warranty service should normally be obtained from the importing dealer or distributor from whom you obtained your product WARNINGS 1 To prevent fire or shock hazard do not expose your Theta product to rain or moisture 2 This unit contains voltages which can cause serious injury or death Do not operate with covers removed Refer all servicing to your authorized Theta dealer 3 For continued protection against fire hazard replace fuses only with the same type and rating of fuses as specified 14 GB 1 01
16. nt LT Center Surround Surround Trigger Preamp Preamp Preamp Preamp Preamp Out Channel Channel Channel Channel Channel Figure 4 Examples of Typical Input and Output Connections optional connection WARNING Each channel is a balanced bridge amplifier thus the negative speaker terminal is NOT a ground and cannot be connected to a ground or a loudspeaker system with a common ground Consult your speaker manufacturer to ensure that any speaker in your system that will be connected to the Intrepid does NOT have internal circuitry with a common ground Damage will occur if the negative terminal is connected to ground or to a terminal of another channel or module Appendix C RS232 Protocol RS232 settings are internally definable via jumper blocks to accommodate interfacing with a wide range of control products Baud rate 9600 or 19200 Echo status AUTO or REQUEST Baud rate Maximum number of bits per second The duration of a single bit is equal to 1 baud rate Echo status Specifies whether the STATUS of each parameter shown in the protocol will automatically AUTO be echoed back to the controller when there is any change or whether the user must manually request REQ the status information be sent to the controller Please refer to page R2 or information on changing these settings All commands will follow the format lt Header gt lt Command Identifier gt lt Argument 1 gt lt Argument 2 gt lt Argument 3 g
17. rchase price Theta reserves the right to modify the design of any product without obligation to purchasers of previously manufactured products and to change the prices or specifications of any product without notice or obligation to any person 3 REMEDY In the event the above product fails to meet the warranty and the above conditions have been met the purchaser s sole remedy under the limited warranty shall be to obtain an RA number and return the product to Theta or an authorized Theta repair center where the defect will be rectified without charge for parts or labor 4 LIMITED TO ORIGINAL PURCHASER This warranty is for the sole benefit of the original purchaser of the covered product and shall not be transferred to a subsequent purchaser of the product 5 DURATION OF WARRANTY This warranty expires 90 days after the date of original purchase If Theta receives the completed warranty registration card within 14 days of original purchase this period is extended to the third anniversary of the original date of purchase or no later that the seventh anniversary of the shipment to the authorized Theta dealer whichever comes first 6 MISCELLANEOUS ANY IMPLIED WARRANTIES RELATING TO THE ABOVE PRODUCT SHALL BE LIMITED TO THE DURATION OF THIS WARRANTY THE WARRANTY DOES NOT EXTEND TO ANY INCIDENTAL OR CONSEQUENTIAL COSTS OR DAMAGES TO THE PURCHASER Some states do not allow limitations on how long an implied warranty lasts or an exclusion or limitat
18. t where lt Header gt lt FEh gt lt EEh gt lt Command identifier gt lt byte gt lt Argument x gt lt byte gt Each command will be able to access the system configuration directly eliminating the need to press any button on the Intrepid front panel Example 1 To put the Intrepid into standby Send FE EE 01 00 00 00 all values in Hex Where FE and EE are the header 01 command 00 main standby 00 put unit in standby and 00 filler 4 characters required OI fi e C I o suaie EE i IA j ET TS j l e Oooo S T T S aww j j Prey Of EEE l ff __uu0A gt O L _ y ouueyo AAA fee AT ie eu ii j OE ej a Prey of weysnidesn eee d f y aww PE y 9uueyo Pi Z C j Li awd j C pte metodo e eres o arene nen o pas I uondiosag anjeA 1q Uuonduosag Ma Mg snle s UOI E LUJOJUI ou surlejuoo aj q yyi ey pau mja eq JJIM sej q SAI RS232 Hardware Connections DB9 DCD Intrepid sends on this pin Intrepid receives on this pin DTR GND DSR RTS CTS Ring CN2 RTS and CTS are not implemented in the Intrepid Jumped Rear panel view of DB9 connector From outside of unit DIR RIAS RTS Jumped Intrepid receives on this pin GND GND Intrepid sends on this pin DCD CTS CN3 Intrepid receives on this pin GN
Download Pdf Manuals
Related Search