Home
Tekkeon ET1000 User's Manual
Contents
1. Bluetooth Wireless Headset Limited Warranty The product enclosed herein is warranted to be free of operational defects for a period of one year from the date of purchase In the event of a defect in operation during the warranty period Tekkeon Inc will replace the defective product when the owner returns all product contents The limited warranty will be considered void if the unit is tampered with subject to misuse negligence or accidental damage has been improperly serviced or if the security seal is removed This warranty is limited to replacement only and shall not cover any other damages Any product returned to Tekkeon Inc with no fault found will be returned to the owner at the owner s expense To obtain warranty coverage please complete and submit the enclosed EzTalker registration card Disclaimer of Warranties Any user of this product does so at the user s own risk To the maximum extent permitted by applicable law Tekkeon Inc and its suppliers provide the hardware and any support services related thereto as is and with all faults and hereby disclaim all warranties and conditions whether express implied or statutory including but not limited to implied warranties of merchantability fitness for a particular purpose non infringement lack of negligence or correspondence to description except for those warranties specifically and expressly provided in the Limited Warranty With respect to the use of this produ
2. status of the headset while tones heard through the headset provide an audible indication of a requested action Following are descriptions of visual and audible indicators provided by your ezTalker headset Headset is in standby mode ready to make and receive calls Headset Is in Pairing Mode Visual Indicators LED Status Blue LED flashes at two second intervals Blue and amber LEDs flash alternately Amber LED flashes Both LEDs are off cee Headset is off Audible Indicators Series of tones increasing in Headset has been turned on pitch Series of tones decreasing in pitch Headset is about to turn off Techn a beep every 32 seconds Double chime Headset has been put into Pairing Mode 00 Headset is muted Beeps every four seconds Troubleshooting If your headset is not communicating with your mobile phone ensure that the headset is on and charged and that you have paired the headset with your mobile phone If you encounter poor reception via the headset verify that you have good reception on your mobile phone or move closer to your mobile phone If the reception is still poor try moving the mobile phone away from your body or to the same side of your body as your headset If you are in a noisy environment and your mobile phone does not accept voice commands dial the number from the mobile phone keypad as the loud background noise may interfere with voice commands ez lalker
3. ET1000 ez lalker Bluetooth Wireless Headset EZTALKER by Tekkeon Is a sleek cord free headset that enables comfortable handsfree communication with your mobile phone EZTALKER 1000 works with your Bluetooth ready mobile phone to provide clear high quality communication While using your EZTALKER headset you can store your mobile phone in your pocket backpack or briefcase just about anywhere in close proximity that is convenient for you Unpacking EZTALKER A gt Your ezTalker package includes the following ezlalker Headset Charging cradle with belt clip Charger ezEarhook ezFit Ring Comfort Pad User guide not shown S ee o Getting to Know EZTALKER TALK Button Used for turning headset on off pairing and making receiving calls Amber and Blue LEDs Provides visual indication of headset status power on off pairing mode muting mode charging mode and low batterv Volume Control Used to adjust the speaker volume and to mute the microphone Microphone Speaker Getting Started Before using ezTalker you must Charge ezTalker Pair ezTalker to your mobile phone Fit ezTalker to your ear Power ezTalker Directions for each of these activities are provided in the following four sections Once these steps are completed you will be ready to use ezTalker USER GUIDE Charging EZTALKER Before using ezlalker you must charge the headset for approximately t
4. ct in no event shall the company be liable for any loss of profit or any other commercial damage including but not limited to special incidental consequential and other damages Customer Service Information Customer service for EzTalker is available at Tekkeon Inc c o ezTalker 3002 Dow Avenue 218 Tustin CA 92780 888 787 5888 714 832 1266 www tekkeon com Tekkeon Inc must issue a Return Merchandise Authorization RMA number for all exchanges or refunds USER GUIDE FCC Statement for Class B Digital Devices This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures Reorient or locate the receiving antenna Increase the separation between the equipment and receiver m Connect the equipment into an o
5. ctly on your Bluetooth headset Refer to the mobile phone user guide for instructions for initiating this feature Ending Calls 1 When you have finished your call press the headset TALK button The call will be disconnected ez lalker Bluetooth Wireless Headset Transferring Calls You can transfer calls from your mobile phone to your headset To Transfer Calls from Your Mobile Phone To The Headset 1 With the call connected to your mobile phone press the TALK button on your headset Adjusting the Volume To Increase the Volume 1 Press and release the top of the VOLUME Figure 5 Volume buttons button to increase the volume one level Repeat until you have reached the desired level To Decrease the Volume 1 Press and release the bottom of the VOLUME button to decrease the volume one level Repeat until you have reached the desired level Muting EZTALKER You can mute and un mute the microphone temporarily so that you cannot be heard by the connected party To Mute the Headset 1 Press and hold either VOLUME button for three seconds While the headset is muted you will hear a beep every four seconds To Un Mute the Headset 1 When the microphone is muted press and hold either VOLUME button for three seconds Storing EZTALKER When you re not using ezTalker you can store it in the charging cradle USER GUIDE Visual And Audible Indicators Two LEDs blue and amber indicate the
6. he headset should fit snugly in your ear and remain in your ear when you move your head However if the speaker is too small for your ear you can add the ezFit Ring that is provided with your headset To Add the ezFit Ring 1 Stretch the ezFit Ring around the end of the microphone as shown Figure 2 To Add the Comfort Pad ezTalker with ezFit Ring 1 Stretch the comfort pad around the end of the microphone as shown The comfort pad can be placed over the ezFit Ring if both are needed To Add the ezEarhook 1 Right ear From the rear of ezTalker insert the bottom of the ezEarhook into the small hole on the left side of the headset pushing until it stops Figure 3 Left ear From the rear of ezTalker insert the bottom of the ezEarhook into the small hole on the right side of the headset pushing until it stops Figure 4 ezEarhook connected for right and left ears N You can mold the soft plastic on ezEarhook to better fit your ear and or adjust the placement of the ezEarhook stem through the headset further in out To Remove the ezEarhook 1 Gently pull the ezEarhook away from the headset until it separates from the headset ezTalker with Comfort Pad USER GUIDE Powering ezTalker To Turn On the Headset Press and hold the TALK button approximately four seconds until the blue LED flashes or until you hear the ON tone 7he headset turns on and Is placed in standby mode ready to make and recei
7. hin 10 feet of the headset 2 Initiate the Bluetooth device pairing discovery feature on the mobile phone Refer to the mobile phone user guide for instructions on initiating this feature 3 With the headset turned off press and hold the TALK button approximately five seconds until the blue and amber LEDs flash alternately or until you hear the PAIRING tone P Release the TALK button 7he headset is now in Pairing Mode O1 Follow the mobile phone prompts and when prompted for the passkey also called passcode or BT PIN enter 0000 the ezTalker passkey When pairing is complete the headset will be placed in Standby Mode ready to make and receive calls the amber LED Will turn off and the blue LED will Hash at two second intervals ez lalker Bluetooth Wireless Headset To Cancel Pairing Mode While you are in pairing mode you can cancel the pairing process and turn off the headset 1 While in pairing mode press and hold the TALK button approximately three seconds until both LEDs turn off or you hear the OFF tone Fitting EZTALKER On Your Ear EzTalker is designed to fit comfortably in your ear For added comfort you can add the optional ezEarhook ezFit Ring and or comfort foam pad For additional comfort you can add the comfort foam pad that Is included with ezTalker To Place the Headset On Your Ear 1 Place the ezTalker speaker in your ear with the microphone angled toward your mouth as shown T
8. utlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Tekkeon www tekkeon com 2003 Tekkeon Inc Revision B5 All Rights Reserved
9. ve calls While the headset is on and in standby mode the blue LED will flash at two second intervals To Turn Off the Headset When the headset is on press and hold the TALK button approximately four seconds until the blue LED turns off or until you hear the OFF tone The headset turns off Making Calls You can make calls from your mobile phone or directly from ezTalker using voice dialing commands if this feature is supported by your mobile phone To Make Calls From Your Mobile Phone 1 Dial the call from your mobile phone he call is automatically connected to your headset To Make Calls Using Voice Dialing if supported by your mobile phone 1 Press the TALK button on your headset 2 When prompted by the mobile phone usually about five seconds speak the name of the person you wish to call 7he call is automatically connected to your headset TIP In a noisy environment you should dial the number trom the mobile phone keypad as the loud background noise may interfere with voice commands Receiving Calls When you receive a call on your mobile phone you will hear the mobile phone ring before you hear the ring tone through your headset as there is a small delay before the headset recognizes the incoming call 1 When you hear ring tone on your headset press the headset TALK button he call s automatically connected to your headset NOTE For some mobile phones you must configure the phone to answer calls dire
10. wo hours When fully charged the battery provides up to four hours of talk time and up to 168 hours of standby time To Charge the Headset 1 Insert ezTalker into the charging cradle as shown 2 Plug the charger into the charging jack on the right side of the charging cradle 3 Plug the charger into a wall outlet Wh e the headset is charging the amber LED on the headset will remain on When the headset is fully charged the amber LED will turn off Figure 1 ezTalker inserted into charging cradle 4 Unplug the charger cable from the wall outlet and the charging cradle BATTERY INDICATION When the battery is low less than 10 of capacity the amber LED will Hash and you ll hear a double beep every 32 seconds Pairing EZTALKER to Your Mobile Phone Pairing is the process of linking the headset with your Bluetooth mobile phone Before using ezTalker with your mobile phone you must pair the devices After this process is complete you can use the headset only with its paired mobile phone To use ezTalker with a different mobile phone you must repeat the pairing process with the new mobile phone In this case the headset will no longer work with the original mobile phone BEFORE YOU PAIR THE HEADSET ENSURE THAT THE BATTERY IS FULLY CHARGED AND REVIEW THE INSTRUCTIONS IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR MOBILE PHONE TO A BLUETOOTH HEADSET To Pair the Devices 1 Turn on the mobile phone and place it wit
Download Pdf Manuals
Related Search
Related Contents
製品安全データシート - シスメックス・ビオメリュー IDL_HS Version 4: User's Guide HDM 1 ULS Bedienungsanleitung/ User manual M-Cab PCI Karte - 2 x Seriell + 1 x Parallel Port Harrier XHD UM 0303 Vivid Colors pLenti6.2- GW/EmGFP Bedienungsanleitung BW Map mobile (Android) - LGL マニュアル、ダウンロード Alcatel OneTouch ONE TOUCH 280 Quick Start Manual Copyright © All rights reserved.
Failed to retrieve file